summaryrefslogtreecommitdiffstats
path: root/drivers/usb/host
Commit message (Collapse)AuthorAgeFilesLines
...
* usb: dwc2: avoid out of bounds accessStefan Brüns2015-12-311-3/+4
| | | | | | | | | | flush_dcache_range may access data after priv->aligned_buffer end if len > DWC2_DATA_BUF_SIZE. memcpy may access data after buffer end if done > 0 Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
* usb: add support of generic OHCI devicesAlexey Brodkin2015-12-173-0/+54
| | | | | | | | | | | This driver is meant to be used with any OHCI-compatible host controller in case if there's no need for platform-specific glue such as setup of controller or PHY's power mode via GPIOs etc. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Simon Glass <sjg@chromium.org> Cc: Marek Vasut <marex@denx.de>
* usb: host: ehci: samsung: Move hcor initialization after usb phy setupLukasz Majewski2015-12-171-2/+2
| | | | | | | | | | | | | With the old order of initialization the hcor pointer has been setup to the same address as Exynos EHCI base address (0x12110000 instead of 0x12110010). Such behaviour was caused by reading value of 0 instead of 0x10 from EHCI HCCPBASE register without doing proper clock initialization before. To fix this problem hcor initialization has been moved after USB PHY setup. Now ehci_readl(&ctx->hcd->cr_capbase) returns correct value. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
* usb: xhci: zynqmp: Removing unused function usb_phy_resetMarek Vasut2015-12-071-17/+0
| | | | | | | This patch removes unsued function usb_phy_reset, rather common function dwc3_phy_reset is used. Signed-off-by: Marek Vasut <marex@denx.de>
* usb: xhci: fsl: Removing unused function usb_phy_resetRajesh Bhagat2015-12-071-17/+0
| | | | | | | This patch removes unsued function usb_phy_reset, rather common function dwc3_phy_reset is used. Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
* usb: xhci: dwc3: Adding reset delay requirement as per dwc3 databookRajesh Bhagat2015-12-071-0/+2
| | | | | | | | | | | As per dwc3 databook, delay is required before taking the core out of reset. This delay is required so that the PHY are stable, and then we can take core out of reset. Reference is taken from linux dwc3 code, file: drivers/usb/dwc3/core.c. Signed-off-by: Sriram Dash <sriram.dash@freescale.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
* usb: add support for generic EHCI devicesAlexey Brodkin2015-12-073-0/+59
| | | | | | | | | | | | This driver is meant to be used with any EHCI-compatible host controller in case if there's no need for platform-specific glue such as setup of controller or PHY's power mode via GPIOs etc. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Simon Glass <sjg@chromium.org> Cc: Marek Vasut <marex@denx.de>
* sunxi: usb: Rename the sunxi usb driver DM entryMarek Vasut2015-12-071-1/+1
| | | | | | | | | | | The DM entry should be unique, otherwise it will collide with other drivers. Fix this by assigning the driver a more unique name than usb_ehci. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Ian Campbell <ijc@hellion.org.uk> Cc: Simon Glass <sjg@chromium.org>
* usb: zynqmp: Fix build warningsMarek Vasut2015-12-071-1/+1
| | | | | | | | The driver does "return 0" in function with void type. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Michal Simek <monstr@monstr.eu> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
* usb: host: xhci-omap: fix build breakFelipe Balbi2015-12-071-1/+1
| | | | | | | | | | Fix the following build break: drivers/usb/host/xhci-omap.c:35:5: error: ‘board_usb_init’ aliased to external symbol ‘__board_usb_init’ int board_usb_init(int index, enum usb_init_type init) ^ Signed-off-by: Felipe Balbi <balbi@ti.com>
* usb: zynqmp: Add XHCI driver supportSiva Durga Prasad Paladugu2015-12-072-0/+144
| | | | | | Added USB XHCI driver support for zynqmp. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
* usb: sandbox: Add support for interrupt operationsSimon Glass2015-11-191-0/+19
| | | | | | | Allow USB device emulation to support interrupt URBs so that we can use USB keyboards with sandbox. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: usb: Remove inactive children after a bus scanSimon Glass2015-11-191-0/+23
| | | | | | | | | | Each scan of the USB bus may return different results. Existing driver-model devices are reused when found, but if a device no longer exists it will stay around, de-activated, but bound. Detect these devices and remove them after the scan completes. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: usb: Deprecate usb_get_dev_index()Simon Glass2015-11-191-0/+9
| | | | | | | | This function should not be used with driver model. While there are users of USB Ethernet that use driver model for USB but not Ethernet, we have to keep it around. Add a comment to that effect. Signed-off-by: Simon Glass <sjg@chromium.org>
* Revert "dm: usb: Use device_unbind_children to clean up usb devs on stop"Simon Glass2015-11-191-3/+0
| | | | | | | | This reverts commit 6cda369509e0d3fa5f9e33c9d71589c4523799fa. We want to avoid having the USB stack rely on unbind. Signed-off-by: Simon Glass <sjg@chromium.org>
* Revert "dm: usb: Rename usb_find_child to usb_find_emul_child"Simon Glass2015-11-191-9/+10
| | | | | | | | This reverts commit 9b510df703d282effba4f56ac567aa8011d56e6b. We want to avoid having the USB stack rely on unbind. Signed-off-by: Simon Glass <sjg@chromium.org>
* Move console definitions into a new console.h fileSimon Glass2015-11-191-0/+1
| | | | | | | | The console includes a global variable and several functions that are only used by a small subset of U-Boot files. Before adding more functions, move the definitions into their own header file. Signed-off-by: Simon Glass <sjg@chromium.org>
* ohci: Add missing cache-flush for hcca areaHans de Goede2015-11-031-0/+1
| | | | | | | | We need to cache-flush the hcca area after the initial memset, otherwise on the first hc_interrupt we might see an old $random value as done_head and try to interpret that as the address for a completed td (followed by chaos). Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* dm: Rename dev_get_parentdata() to dev_get_parent_priv()Simon Glass2015-10-233-9/+9
| | | | | | | | The current name is inconsistent with other driver model data access functions. Rename it and fix up all users. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
* usb: ehci-marvell.c: Add DM supportStefan Roese2015-10-212-16/+77
| | | | | | | | | | | | This patch adds driver model (DM) support to the Marvell EHCI driver. This will be used by the MVEBU SoC's, currently Armada XP and 38x. Tested on Marvell Armada XP and 38x eval boards. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Luka Perkov <luka.perkov@sartura.hr>
* Move ALLOC_CACHE_ALIGN_BUFFER() to the new memalign.h headerSimon Glass2015-09-114-0/+4
| | | | | | | Now that we have a new header file for cache-aligned allocation, we should move the stack-based allocation macro there also. Signed-off-by: Simon Glass <sjg@chromium.org>
* usb: ehci: remember init modeStephen Warren2015-09-072-1/+7
| | | | | | | | | | | | | | When an EHCI device is registered in device mode, the HW isn't actually initialized at all, and hence isn't left in a running state. Consequently, when the device is deregistered, ehci_shutdown() will fail, since the HW bits it expects to see set in response to its shutdown requests will not be sent, and the message "EHCI failed to shut down host controller." will be printed. Fix ehci-hcd.c to remember whether the device was registered in host or device mode, and only call ehci_shutdown() for host mode registrations. Signed-off-by: Stephen Warren <swarren@nvidia.com>
* dm: Use dev_get_addr() where possibleSimon Glass2015-08-312-4/+6
| | | | | | | | | | This is a convenient way for a driver to get the hardware address of a device, when regmap or syscon are not being used. Change existing callers to use it as an example to others. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
* usb: dwc2: Rename to dwc2_usbMarek Vasut2015-08-191-1/+1
| | | | | | | This driver is not used only on exynos, but also on Altera SoCFPGA, HiSilicon SoCs, RPi etc, so rename it accordingly to prevent confusion. Signed-off-by: Marek Vasut <marex@denx.de>
* usb: dwc2: Add original Synopsys compat stringMarek Vasut2015-08-191-0/+1
| | | | | | Add the Synopsys compatible string. This is used in SoCFPGA DT files. Signed-off-by: Marek Vasut <marex@denx.de>
* usb: host: xhci-omap: invoke board_usb_cleanup in xhci_hcd_stopKishon Vijay Abraham I2015-08-191-0/+1
| | | | | | | | | | | | xhci omap driver has board_usb_init in xhci_hcd_init but doesn't have the corresponding cleanup function in xhci_hcd_stop. Fix it here by invoking board_usb_cleanup() in xhci_hcd_stop(). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Marek Vasut <marex@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
* usb: xhci: Fix a potential NULL pointer dereferenceSergey Temerkhanov2015-08-191-5/+14
| | | | | | | | | This patch fixes a potential NULL pointer dereference arising on non-present/non-initialized xHCI controllers and adds some error handling to xHCI code Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com> Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
* usb: spear: Add support for both SPEAr600 EHCI controllersStefan Roese2015-08-191-3/+35
| | | | | | | | | | | USB EHCI on SPEAr600 has not been tested for a while. The base controller addresses are missing. This patch adds the defines to the header. And adds the missing code. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Vipin Kumar <vk.vipin@gmail.com> Cc: Marek Vasut <marex@denx.de>
* imx: usb: ehci-mx6: wait_for_bit to check reg statusAdrian Alonso2015-08-191-4/+33
| | | | | | | Add wait_for_bit to check reg bit status and replace unbounded loops to check usb command status Signed-off-by: Adrian Alonso <aalonso@freescale.com>
* imx: usb: ehci-mx6: add usb support for imx7d socAdrian Alonso2015-08-192-19/+82
| | | | | | Extend ehci-mx6 usb driver to support imx7d usb Signed-off-by: Adrian Alonso <aalonso@freescale.com>
* imx: usb: ehci-mx6: document board specific functionsAdrian Alonso2015-08-191-0/+31
| | | | | | | | | | Document target board specific functions board_ehci_hcd_init - override usb phy mode board_ehci_hcd_init - set usb vbus voltage board_ehci_power - enables/disables usb vbus voltage Signed-off-by: Adrian Alonso <aalonso@freescale.com>
* imx: usb: ehci-mx6: reg accessor cleanupsAdrian Alonso2015-08-191-33/+18
| | | | | | Cleanup read/write register access, use clr/set bits_le32 Signed-off-by: Adrian Alonso <aalonso@freescale.com>
* usb: lpc32xx: add host USB driverSylvain Lemieux2015-08-182-0/+232
| | | | | | | | | | | | | Incorporate USB driver from legacy LPCLinux NXP BSP. The files taken from the legacy patch are: - lpc32xx USB driver - lpc3250 header file USB registers definition. The legacy driver was updated and clean-up as part of the integration with the latest u-boot. Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Vladimir Zapolskiy <vz@mleia.com>
* arm: mvebu: add multiple usb-hostcontroller support for AXPAnton Schubert2015-08-171-8/+11
| | | | | | | | | | | This patch adds support for multiple hostcontrollers to the ehci-marvell driver and enables all 3 usb-hcs on the db-mv784mp-gp board. It depends on the initial Armada XP usb support patch from Stefan. Signed-off-by: Anton Schubert <anton.schubert@gmx.de> Reviewed-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
* arm: mvebu: Enable USB EHCI support on Armada XPStefan Roese2015-08-171-1/+8
| | | | | | | | | | | | | | | | | This patch enables the USB EHCI support for the Marvell Armada XP (AXP) SoCs. In compatism to the Armada 38x (A38x), the AXP needs to configure the USB PLL and the USB PHY's specifically in U-Boot. The A38x has done this already in the bin_hdr (SPL U-Boot). Without this, accessing the controller registers in U-Boot or Linux will hang the CPU. Additionally, the AXP uses a different USB EHCI base address. This patch also takes care of this by runtime SoC detection in the Marvell EHCI driver. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Anton Schubert <anton.schubert@gmx.de> Cc: Marek Vasut <marex@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
* usb: ohci: enable cache supportWu, Josh2015-08-122-12/+2
| | | | | | | | Remove the CONFIG_DM_USB limitation to enable cache support functions. Tested on SAMA5D3x-EK board. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
* dwc2: Add dcache supportAlexander Stein2015-08-121-7/+17
| | | | | | | | | | | This adds dcache support for dwc2. The DMA buffers must be DMA aligned and is flushed for outgoing transactions before starting transfer. For ingoing transactions it is invalidated after the transfer has finished. Signed-off-by: Alexander Stein <alexanders83@web.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> [trini: Update to apply again on top of DM patches] Signed-off-by: Tom Rini <trini@konsulko.com>
* sunxi: usb-phy: Never power off the usb portsHans de Goede2015-08-082-2/+0
| | | | | | | | | | | | | | | | | | | | | USB devices are not really designed to get the power bounced off and on at them. Esp. USB powered harddisks do not like this. Currently we power off the USB ports both on a "usb reset" and when booting the kernel, causing the usb-power to bounce off and then back on again. This patch removes the powering off calls, fixing the undesirable power bouncing. Note this requires some special handling for the OTG port: 1) We must skip the external vbus check if we've already enabled our own vbus to avoid false positives 2) If on an usb reset we no longer detect that the id-pin is grounded, turn off vbus as that means an external vbus may be present now Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* Merge git://git.denx.de/u-boot-dmTom Rini2015-08-061-54/+201
|\
| * dm: usb: Add driver-model support to dwc2Simon Glass2015-08-061-0/+97
| | | | | | | | | | | | | | Add driver model support to this driver so it can be used with the new USB stack. Signed-off-by: Simon Glass <sjg@chromium.org>
| * dm: usb: Prepare dwc2 driver for driver-model conversionSimon Glass2015-08-061-54/+104
| | | | | | | | | | | | | | Put all global data in a structure and move (what will be) common code into common functions. This will make the driver-model conversion much easier. Signed-off-by: Simon Glass <sjg@chromium.org>
* | Tegra: clocks: Add 38.4MHz OSC support for T210 useTom Warren2015-08-051-5/+13
|/ | | | | | | | | | | | | | | Added 38.4MHz/48MHz entries to pll_x_table for CPU PLL. Needs to be measured - should be close to 700MHz (1.4G/2). Note that some freqs aren't in the PLLU table in T210 TRM (13, 26MHz), so I used the 12MHz table entry for them. They shouldn't be selected since they're not viable T210 OSC freqs. Since there are now 2 new OSC defines, all tables (pll_x_table, PLLU) had to increase by two entries, but since 38.4/48MHz are not viable osc freqs on T20/30/114, etc, they're just set to 0. Signed-off-by: Tom Warren <twarren@nvidia.com>
* usb: USB storage-specific part ifdef in uclassPaul Kocialkowski2015-08-051-0/+2
| | | | | | | usb_stor_reset is only defined when USB storage support is enabled, thus the function is not declared when such support is missing. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* usb: dwc2: Call board_usb_init() from usb_lowlevel_init()Peter Griffin2015-08-051-0/+4
| | | | | | | | | | This patch makes the dwc2 controller like ehci / ohci / xhci controllers by calling the board_usb_init() function from usb_lowlevel_init. This can then be implemented by specific platforms to initialise their USB hardware (phys / clocks etc). Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2015-08-021-0/+7
|\
| * arm: mx6: usb: kconfig: add USB_EHCI_MX6 kconfig optionNikita Kiryanov2015-08-021-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | Add USB_EHCI_MX6 option to menuconfig and use it when migrating cm-fx6 usb config to defconfig. Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* | ARM: Tegra210: Add support to common Tegra source/config filesTom Warren2015-07-281-1/+30
| | | | | | | | | | | | | | | | | | | | | | Derived from Tegra124, modified as appropriate during T210 board bringup. Cleaned up debug statements to conserve string space, too. This also adds misc 64-bit changes from Thierry Reding/Stephen Warren. Signed-off-by: Tom Warren <twarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
* | Merge git://git.denx.de/u-boot-usbTom Rini2015-07-247-240/+222
|\ \
| * | usb: ehci-marvell: Drop wrl accessor functionStefan Roese2015-07-221-14/+12
| | | | | | | | | | | | | | | | | | | | | | | | This patch removes the wrl accessor function from the Marvell EHCI driver by replacing it with the writel function. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de>
| * | drivers: usb: fsl: Remove LS102XA immap inclusionNikhil Badola2015-07-221-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | Remove LS102XA immap header inclusion from xhci fsl driver. It removes redefinition warnings when built for platforms other than LS102XA Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
OpenPOWER on IntegriCloud