summaryrefslogtreecommitdiffstats
path: root/drivers/serial/serial_pl01x.c
Commit message (Collapse)AuthorAgeFilesLines
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-241-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* serial_pl011: Set RTS during initializationJoshua Housh2012-12-071-2/+2
| | | | | | | | | | | If the pl011 is connected to another device which has hardware flow-control on, characters are never received by the pl011. Asserting RTS when flow-control is off will have no effect. This is in line with how Linux behaves. Signed-off-by: Joshua Housh <joshua.housh@calxeda.com> Tested-by: Marek Vasut <marex@denx.de>
* serial: Use default_serial_puts() in driversMarek Vasut2012-10-171-8/+1
| | | | | | | | | | Replace the in-place ad-hoc implementation of serial_puts() within the drivers with default_serial_puts() call. This cuts down on the code duplication quite a bit. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
* serial: Remove CONFIG_SERIAL_MULTI from serial driversMarek Vasut2012-10-151-32/+0
| | | | | | | | | | | | Remove the support for not-CONFIG_SERIAL_MULTI part from serial port drivers and some board files. Since CONFIG_SERIAL_MULTI is now enabled by default, that part is a dead code. Remove it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
* serial: arm: Implement CONFIG_SERIAL_MULTI into pl01x serial driverMarek Vasut2012-10-151-7/+62
| | | | | | | | | | | | | | | | | Implement support for CONFIG_SERIAL_MULTI into pl01x serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the pl01x driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Mathieu J. Poirier <mathieu.poirier@linaro.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: John Rigby <john.rigby@linaro.org> Cc: Rabin Vincent <rabin.vincent@stericsson.com>
* snowball: Add support for ux500 based snowball boardMathieu J. Poirier2012-09-011-0/+2
| | | | | | | | | | | Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: John Rigby <john.rigby@linaro.org> Acked-by: Tom Rini <trini@ti.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Conflicts: drivers/gpio/Makefile
* serial: pl01x: drain PL01x FIFO before baudrate changeLinus Walleij2011-10-221-0/+10
| | | | | | | | | Not draining the FIFO and waiting for the UART to be non-busy before changing baudrate results in crap characters on the console, so let's wait for the FIFO to drain and the last character to be clocked out before we do that. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Serial: p1011: new vendor init optionsJohn Rigby2011-05-121-3/+27
| | | | | | | | | | | | | | | | | | | | Two new options: CONFIG_PL011_SERIAL_RLCR Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500) have separate receive and transmit line control registers. Set this variable to initialize the extra register. CONFIG_PL011_SERIAL_FLUSH_ON_INIT On some platforms (e.g. U8500) U-Boot is loaded by a second stage boot loader that has already initialized the UART. Define this variable to flush the UART at init time. empty fifo on init Signed-off-by: John Rigby <john.rigby@linaro.org> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
* pl01x: use C structs and readl/writelRabin Vincent2010-11-301-20/+30
| | | | | | | | Use C structs for registers, and use readl/writel instead of custom accessors. Acked-by: Michael Brandt <michael.brandt@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
* ARMV7: Fixed baudrate setting in pl01x driverMatt Waddel2010-10-131-55/+38
| | | | | | | | | The pl01x serial driver was lacking the code to switch baudrates from the command line. Fixed by simply saving the new baudrate and calling serial_init() again. Also fixed CamelCase variables, I/O accessors and comment style. Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
* Moved conditional compile into MakefileAndreas Engel2008-09-091-10/+5
| | | | Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>
* Merged serial_pl010.c and serial_pl011.c.Andreas Engel2008-09-091-0/+228
They only differ in the init function. This also adds the missing watchdog support for the PL011. Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>
OpenPOWER on IntegriCloud