summaryrefslogtreecommitdiffstats
path: root/configs/Mele_M9_defconfig
Commit message (Collapse)AuthorAgeFilesLines
* kconfig: remove meaningless prefixes in defconfig filesMasahiro Yamada2015-03-151-11/+11
| | | | | | | | | | | | Since commit e02ee2548afe (kconfig: switch to single .config configuration), the prefixes in defconfig files such as "+S:", "+ST:", etc., are meaningless. This commit was generated by the following command: find configs -name '*_defconfig' | xargs sed -i 's/^+*S*T*://' Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* sunxi: Remove CONFIG_TARGET_FOO for sun4i, sun6i and sun8i boardsHans de Goede2015-01-221-1/+0
| | | | | | | | | | CONFIG_TARGET_FOO is only used in board/sunxi/Makefile to select the dram config for sun5i and sun7i boards and in board/sunxi/gmac.c for some special handling of the bananapi/bananapro (both sun7i), iow it is not used at all on any sun4i, sun6i and sun8i boards so lets get rid of it there. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: axp221: Make dcdc1 voltage configurableHans de Goede2015-01-141-0/+2
| | | | | | | | | | The dcdc1 voltage is typically used as generic 3.3V IO voltage for things like GPIO-s, sdcard interfaces, etc. On most boards this is undervolted to 3.0V to safe battery, but not on all, make it configurable so that we can use the same settings as the original firmware on all boards. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: axp221: Add Kconfig help and sane defaults for typical ldo usageHans de Goede2015-01-141-3/+0
| | | | | | | | | Some of the ldo-s of the axp221 are used in the same way on most boards, add comments to the Kconfig help text to reflect this, and give them defaults matching their typical usage. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun6i: Make dram clk and zq value Kconfig optionsHans de Goede2015-01-141-0/+2
| | | | | | | | | | | | It turns out that there is a too large spread between boards to handle this with a default value, turn this into Kconfig options, and set the values the factory images are using for the Colombus and Mele_M9 boards. Note this changes the ZQ default when not overriden through defconfig from 120 to 123, as that is what most boards seem to actually use. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun6i: Add gmac support for sun6i boardsHans de Goede2014-11-251-1/+1
| | | | | | | Hookup the gmac found on the sun6i / A31 SoCs. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun6i: Correct Mele M9 Vbus gpio settingsHans de Goede2014-11-251-2/+4
| | | | | | | | I noticed that the kernel and u-boot settings were different, double checking has confirmed that the kernel settings are correct. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun6i: ehci: Add sun6i ehci supportHans de Goede2014-11-131-0/+3
| | | | | | | | Add support for the 2 ehci controllers found on the sun6i (A31) soc. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Marek Vasut <marex@denx.de>
* sun6i: Add Mele M9 boardHans de Goede2014-11-131-0/+15
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
OpenPOWER on IntegriCloud