summaryrefslogtreecommitdiffstats
path: root/board
Commit message (Collapse)AuthorAgeFilesLines
* Merge remote-tracking branch 'u-boot-imx/master'Albert ARIBAUD2014-10-0820-71/+1677
|\ | | | | | | | | | | | | The single file conflict below is actually trivial. Conflicts: board/boundary/nitrogen6x/nitrogen6x.c
| * nitrogen6x: display use I2C detect for HDMIEric Nelson2014-10-061-3/+3
| | | | | | | | | | | | | | | | | | | | The HPD pin and RX_SENSE registers have proven to be less reliable than using I2C on the EDID pins for detection of an HDMI monitor. In particular, when the HDMI output is reset through a "reboot" cycle, the detect_hdmi() routine often bounces, resulting in a failure to detect a connected monitor. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: display: add wvga-lvds panelEric Nelson2014-10-061-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | Add support for WVGA (800x480) panels using VESA GTF timings over LVDS. No auto-detection is supported, so you must configure this panel manually through the 'panel' environment variable: U-Boot > setenv panel svga U-Boot > saveenv && reset Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: display: add Ampire 1024x600 panelEric Nelson2014-10-061-0/+20
| | | | | | | | | | | | | | | | | | Add support for an Ampire 1024x600 LVDS panel with integrated Ilitek capacitive touch screen. Auto-detection is enabled, so no explicit configuration is needed. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: display: add svga display (800x600)Eric Nelson2014-10-061-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | Add support for 800x600 18-bit RGB displays using VESA GTF timings. No auto-detection is supported, so you must configure this panel manually through the 'panel' environment variable: U-Boot > setenv panel svga U-Boot > saveenv && reset Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: display: add support for fusion 7 displayEric Nelson2014-10-061-0/+20
| | | | | | | | | | | | | | | | | | | | Add support for the Touch Revolution Fusion7 display: 800x480 RGB with a custom F0710A resistive touch controller. Auto-detection of this panel is supported so no configuration is required. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: display: add LDB-WXGA-S for SPWG 1280x800 displaysEric Nelson2014-10-061-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for LVDS WXGA displays that use the SPWG encoding standard instead of JEIDA. No auto-detection is enabled and you must explicitly set the 'panel' environment variable: U-Boot > setenv panel LDB-WXGA-S U-Boot > saveenv && reset Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: display: add support for LG-9.7 LVDS displayEric Nelson2014-10-061-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for LG 9.7" LVDS panel (1024x768) with integrated eGalax touch screen. Note that this panel differs only slightly from the Hannstar XGA panel (margins). No auto-detection is available because it shares the same touch controller as the Hannstar-XGA display, so you'll need to configure it through the 'panel' environment variable: U-Boot > setenv panel LG-9.7 U-Boot > saveenv && reset Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: display: add qvga panelEric Nelson2014-10-061-0/+20
| | | | | | | | | | | | | | | | | | | | | | Add support for a 1/4 VGA panel with a 24-bit RGB interface. No auto-detection is enabled, so you must configure the 'panel' environment variable to use this display: U-Boot > setenv panel qvga U-Boot > saveenv && reset Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: display: add support lvds jeida screenRobert Winkler2014-10-061-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for Boundary Devices 7" and 10.1" 1280x800 displays with integrated FocalTech ft5x06 10-point touch controller. Because they share the touch controller with the 1024x600 displays, auto-detection is disabled and you must explicitly set the 'panel' environment variable: U-Boot > setenv panel LDB-WXGA U-Boot > saveenv && reset Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com> Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: prevent warnings about board_ehci* callbacksEric Nelson2014-10-061-0/+1
| | | | | | | | | | | | | | Include declarations of board_ehci callbacks to prevent compiler warnings and enforce function prototypes. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: phy: add 100 us delay after phy resetTroy Kisky2014-10-061-0/+1
| | | | | | | | | | | | | | | | Testing shows that the Micrel PHY may not be completely out of reset if accessed immediately. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: staticize board fileEric Nelson2014-10-061-14/+16
| | | | | | | | | | | | | | | | Declare locally-used data structures and functions as static and pull in header files to prevent compiler warnings of "Should it be static?" when building with "make C=1". Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: configure SGTL5000, CSI camera clock outputsTroy Kisky2014-10-061-1/+7
| | | | | | | | | | | | | | | | | | | | Configure CLKO outputs for SGTL5000, CSI camera. The sys_mclk output for the SGTL500 in particular prevents Windows CE from properly driving audio. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: power-down miscellanous peripheralsEric Nelson2014-10-061-4/+43
| | | | | | | | | | | | | | | | Ensure that cameras and USB OTG power are in a stable (reset) state at reset by configuring their pads and toggling GPIOs. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: configure SD2 pads for SDIO on USDHC2Eric Nelson2014-10-061-0/+11
| | | | | | | | | | | | | | | | | | | | Pads SD2_CLK/CMD/DAT0-3 are connected to an SDIO WiFi device on Nitrogen and unconnected on BD-SL-i.MX6 (sabre lite). Configure them as SDIO pins to prevent them from being in a state that confuses the WiFi part. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * nitrogen6x: simplify board_mmc_getcdTroy Kisky2014-10-061-10/+4
| | | | | | | | | | | | | | The same logic applies to both SD card slots, only with different GPIOs and the code should make that easier to see. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
| * nitrogen6x: implement board_cfb_skip() to disable text outputEric Nelson2014-10-061-0/+5
| | | | | | | | | | | | | | | | Several customers have asked to leave the display quiet during boot, so allow the user to express this request by the presence of environment variable "novideo". Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * imx6: add Bachmann OT1200 boardChristian Gmeiner2014-10-066-0/+478
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the OT1200 series of devices. Following components are used in u-boot: + ethernet + i2c + emmc + gpio For more details see README. Changes v1 > v2 - make use of enable_cspi_clock(..) - fix usage of OUTPUT_40OHM define - added README Changes v2 > v3 - improve spelling in README - added own copy of mx6q_4x_mt41j128.cfg Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
| * nitrogen6x: Update DDR timings for 2G memory arrangementEric Nelson2014-10-061-12/+12
| | | | | | | | | | | | | | | | | | Update DDR calibration settings based on a larger test set. The initial values were gathered on a small number of boards, and have been found to fail on some boards under load. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * ARM: mx6: gw_ventana: Remove superfluous memset of GD in board_init_fStefan Roese2014-10-011-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | Zeroing GD in board_init_f() is not needed any more. As its now done in crt0.S. The patch that clears the GD in crt0.S is this one: aae2aef9 [arm: Set up global data before board_init_f()] from Simon. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Tim Harvey <tharvey@gateworks.com>
| * imx: mx6dlarm2: Add support for i.MX6Q/DL arm2 LPDDR2 boardsYe.Li2014-09-304-7/+510
| | | | | | | | | | | | | | | | Update the ddr scripts for LPDDR2 and add two build configs for LPDDR2 arm2 board. Since the LPDDR2 arm2 board has different DDR size, use CONFIG_DDR_MB in defconfig to replace the PHYS_SDRAM_SIZE. Signed-off-by: Ye.Li <B37916@freescale.com>
| * imx: mx6dlarm2: Add support for i.MX6DL arm2 DDR3 boardYe.Li2014-09-303-0/+149
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the i.MX6DL arm2 board support. The i.MX6DL ARM2 shared the same board with i.MX6Q ARM2 board since the i.MX6DL is pin-pin compatible with i.MX6Q. The patch also support the DDR 32-BIT mode option. Please define CONFIG_DDR_32BIT in the board configure file to enable DDR 32-BIT mode.But due to the board design, it's 64bit DDR buswidth physically, so, if you CONFIG_DDR_32BIT, the DDR memory size will be half of it. Signed-off-by: Ye.Li <B37916@freescale.com>
| * arm: mxs: olinuxino: Fine-tune DRAM configurationMarek Vasut2014-09-291-0/+30
| | | | | | | | | | | | | | | | | | Add fine-tuning for the DRAM configuration according to the DRAM chip datasheet. THis configuration applies to both Hynix HY5DU12622DTP and Samsung K5H511538J-D43 . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
| * arm: mxs: olinuxino: Enable USB only when neededMarek Vasut2014-09-291-2/+14
| | | | | | | | | | | | | | | | Enable the power to the USB port only when the USB port is really needed. Do not enable the power unconditionally. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
| * imx: ddr: Move mx6q_4x_mt41j128.cfg to mx6sabresd boardNitin Garg2014-09-222-0/+169
| | | | | | | | | | | | | | | | | | | | Provide cgtqmx6eval board its own variant of ddr setup config file. Move board/freescale/imx/ddr/ mx6q_4x_mt41j128.cfg to board/freescale/mx6sabresd/ as this is was designed for the mx6sabresd board. Signed-off-by: Nitin Garg <nitin.garg@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic2014-09-22580-2112/+1737
| |\
| * | imx: Fix warning by building vf610twr_nandStefano Babic2014-09-171-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit d6d07a9b... arm: vf610: add NAND support for vf610twr generates the following warnings: WARNING: no status info for 'vf610twr_nand' WARNING: no maintainers for 'vf610twr_nand'WARNING: no status info for 'vf610twr_nand' This is due to the fact that vf610twr_nand_defconfig has no Maintainer. This patch proposed Alison as Maintainer and fix it. Signed-off-by: Stefano Babic <sbabic@denx.de> Acked-by: Alison Wang <b18965@freescale.com> CC: Stefan Agner <stefan@agner.ch>
| * | mx6qsabreauto: Staticize when possibleFabio Estevam2014-09-161-8/+8
| | | | | | | | | | | | | | | | | | Turn all local symbols into static in order to make sparse happy. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx6sxsabresd: Staticize i2c_pad_info1Fabio Estevam2014-09-161-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | i2c_pad_info1 is only used locally, so it can be made static. Fix the following sparse warning: board/freescale/mx6sxsabresd/mx6sxsabresd.c:160:22: warning: symbol 'i2c_pad_info1' was not declared. Should it be static? Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | arm: vf610: add NAND support for vf610twrStefan Agner2014-09-161-3/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds NAND support for the Vybrid tower system (TWR-VF65GS10) provided by the vf610_nfc driver. Full 16-Bit bus width is supported. Also an aditional config vf610twr_nand is introduced which gets the environment from NAND. However, booting U-Boot from NAND is not yet possible due to missing boot configuration block (BCB). Signed-off-by: Stefan Agner <stefan@agner.ch>
* | | vf610twr: Tune DDR initialization settingsAnthony Felice2014-10-071-34/+60
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Removed settings in unsupported register fields. They didn’t do anything, and in most cases, were not documented in the reference manual. Changed register settings to comply with JEDEC required values. Changed timing parameters because they included full clock periods that were doing nothing. Signed-off-by: Anthony Felice <tony.felice@timesys.com> [rebased on v2014.10-rc2] Signed-off-by: Stefan Agner <stefan@agner.ch>
* | | Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2014-09-266-4/+100
|\ \ \
| * | | board/ls1021aqds: Add DDR4 supportYork Sun2014-09-253-1/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig for this variant to enable DDR4 support. RAW timing parameters are not added for DDR4. The board timing parameters are only tuned for single- rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM availability. Signed-off-by: York Sun <yorksun@freescale.com> CC: Alison Wang <alison.wang@freescale.com>
| * | | ARMv8/ls2085a: Enable secondary coresYork Sun2014-09-251-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Spin table is at the very beginning of boot code. Each core has an individual release address within the spin table, the ft_cpu_setup fn updates the "cpu-release-addr" property of each cpu node with the corresponding release address. Also fix CPU_RELEASE_ADDR to point to secondary_boot_func. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
| * | | ARMv8/ls2085a_emu: Enable DP-DDR as standalone memory blockYork Sun2014-09-253-3/+73
| | | | | | | | | | | | | | | | | | | | | | | | | | | | DP-DDR is used for DPAA, separated from main memory pool for general use. It has 32-bit bus width and use a standard DDR4 DIMM (64-bit). Signed-off-by: York Sun <yorksun@freescale.com>
| * | | board/ls2085a: Update env_addr after NOR flash relocationPrabhakar Kushwaha2014-09-241-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LS2085a has 2 regions in system memory map. Region1 is default map from where system boots. Once u-boot is moved to DDR, IFC is re-mapped to Region2. So, update gd->env_addr to reflect correct address. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | | | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2014-09-267-11/+46
|\ \ \ \
| * | | | board/t1040qds: Add sgmii ports support in 0xA7 protocolPriyanka Jain2014-09-241-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1042QDS (T1042 is T1040 Personality without L2 switch) supports following sgmii interfaces with serdes protocol 0xA7 -SGMII-MAC3 on Lane B - slot 7 -SGMII-MAC5 on Lane H - slot 7 -SGMII2.5G-MAC1 on Lane C - slot 6 -SGMII2.5G-MAC2 on Lane D - slot 5 Add support of above sgmii interfaces Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
| * | | | powerpc/t104xrdb: Set DDR ODT to 75ohmPriyanka Jain2014-09-242-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DDR-ODT require cfg_dram_type switch set properly as per DDR type. T1040RDB, T1042RDB boards have DDR3L type DDR, so cfg_dram_type should be set to OFF for DDR3L Update t104xrdb/README for switch setting Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | | | powerpc/t104xrdb: Add T1042RDB board supportvijay rai2014-09-243-2/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1042RDB is a Freescale reference board that hosts the T1042 SoC (and variants). The board is similar to T1040RDB, T1042 is a reduced personality of T1040 SoC without Integrated 8-port Gigabit(L2 Switch). T1042RDB is configured with serdes protocol 0x86 which can support following interfaces - 2 RGMII's on DTSEC4, DTSEC5 - 1 SGMII on DTSEC3 DTSEC1, DTSEC2 are not connected on board. This Patch - add T1042RDB support - updates README file for T1042RDB details and update commands for switching to alternate banks from vBank0 to vBank4 and vice versa This patch also does minor clean ups for fdt defines for T1042RDB and T1042RDB_PI board Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | | | powerpc/t104xrdb: Add Support of rcw for T1042RDB in u-bootvijay rai2014-09-242-4/+11
| |/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support of rcw for T1042RDB, it makes following changes : - Adds t1042_rcw.cfg file for serdes protocol 0x86 for T1042RDB - Renames t1042_pi_rcw.cfg file from t1042_rcw.cfg and also updates comments for valid serdes protocol which is 0x06 - Also updates CONFIG_SYS_FSL_PBL_RCW for T1042RDB Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | | | cosmetic: replace MIN, MAX with min, maxMasahiro Yamada2014-09-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The macro MIN, MAX is defined as the aliase of min, max, respectively. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | | MAINTAINERS: comment out blank M: fieldMasahiro Yamada2014-09-24106-106/+106
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit ddaf5c8f3030050fcd356a1e49e3ee8f8f52c6d4 (patman: RunPipe() should not pipe stdout/stderr unless asked), Patman spits lots of "Invalid MAINTAINERS address: '-'" error messages for patches with global changes. It takes too long for Patman to process them. Anyway, "M: -" does not carry any important information. Rather, it is just like a place holder in case of assigning a new board maintainer. Let's comment out. This commit can be reproduced by the following command: find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | | MAINTAINERS: comment out invalid maintainersMasahiro Yamada2014-09-2450-50/+50
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The "S: Orphan" in MAINTAINERS means that the maintainer in the "M:" field is unreachable (i.e. the email address is not working). (Refer to the definition of "Orphan" adopted in U-Boot in the log of commit 31f1b654b2f395b69faa5d0d3c1eb0803923bd3b, "boards.cfg: move boards with invalid emails to Orphan") For patch files adding global changes, scripts/get_maintainer.pl adds bunch of such invalid email addresses, which results in tons of annoying bounce emails. This commit can be reproduced by the following command: find . -name MAINTAINERS | xargs sed -i -e ' /^M:[[:blank:]]/ { N /S:[[:blank:]]Orphan/s/^/#/ } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* | | | mpc8xx: move common linker scripts into the CPU directoryMasahiro Yamada2014-09-248-660/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Each CPU of PowerPC has its default linker script under the CPU directory, except mpc8xx. Every mpc8xx board has its own linker script under the board directory, resulting in lots of duplication of linker scripts. I notice eight mpc8xx boards have the same linker script. We can decrease the number of linker scripts by putting a single default linker script, arch/powerpc/cpu/mpc8xx/u-boot.lds. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Stefan Roese <sr@denx.de>
* | | | spi: mxc: fix sf probe when using mxc_spiNikita Kiryanov2014-09-248-1/+45
|/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MXC SPI driver has a feature whereas a GPIO line can be used to force CS high across multiple transactions. This is set up by embedding the GPIO information in the CS value: cs = (cs | gpio << 8) This merge of cs and gpio data into one value breaks the sf probe command: if the use of gpio is required, invoking "sf probe <cs>" will not work, because the CS argument doesn't have the GPIO information in it. Instead, the user must use "sf probe <cs | gpio << 8>". For example, if bank 2 gpio 30 is used to force cs high on cs 0, bus 0, then instead of typing "sf probe 0" the user now must type "sf probe 15872". This is inconsistent with the description of the sf probe command, and forces the user to be aware of implementaiton details. Fix this by introducing a new board function: board_spi_cs_gpio(), which will accept a naked CS value, and provide the driver with the relevant GPIO, if one is necessary. Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Eric Benard <eric@eukrea.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Marek Vasut <marex@denx.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* | | Merge branch 'misc' of git://git.denx.de/u-boot-x86Tom Rini2014-09-231-3/+3
|\ \ \ | |_|/ |/| |
| * | sandbox: Update minor documentation changesJagannadha Sutradharudu Teki2014-09-211-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | - Use _defconfig instead of _config, but still _config is working. - Corrected README.sandbox path in ./README Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* | | Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2014-09-211-0/+4
|\ \ \
OpenPOWER on IntegriCloud