summaryrefslogtreecommitdiffstats
path: root/board/xilinx/zynqmp/zynqmp.c
Commit message (Collapse)AuthorAgeFilesLines
* ARM64: zynqmp: Add support for standard distro boot commandsMichal Simek2016-06-061-7/+27
| | | | | | | | | | | | | Nand and QSPI are not defined now but this will be extended. Based on selected bootmode boot_targets are rewritten. Patch also contains detection if variables are saved. If yes don't rewrite boot_targets variable. Also move variable setup to the end of file because SCSI needs to be defined before others macros are using it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Alexander Graf <agraf@suse.de>
* ARM64: zynqmp: Add support for reading MAC from eepromMichal Simek2016-05-241-0/+17
| | | | | | | | | | | | | | | | | | | | | | Add support for on board eeprom with programmed MAC for using in u-boot to have uniq address for every board. Most of the time uniq MAC address is on a label on the board. If address is not programmed use these command to program it. On zcu102: ZynqMP> mm.b 0 00000000: 00 ? 00 00000001: a0 ? 0a 00000002: 35 ? 35 00000003: 02 ? 02 00000004: 00 ? ef 00000005: 00 ? 67 00000006: 00 ? q i2c dev 5 i2c write 0 54 20 6 i2c md 54 20 Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Remove netdev.h from board fileMichal Simek2016-04-131-1/+0
| | | | | | | | | | | | | | | | Including netdev.h is causing compilation warning: + int fecmxc_register_mii_postcall(struct eth_device *dev, int (*cb)(int)); + ^ w+In file included from ../board/xilinx/zynqmp/zynqmp.c:9:0: w+../include/netdev.h:204:41: warning: ‘struct eth_device’ declared inside parameter list [enabled by default] w+../include/netdev.h:204:41: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default] This patch removes it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Make DDR detection code work on 32bit systemMichal Simek2016-04-131-3/+3
| | | | | | | Define u64 types to be usable on 32bit system because of 64bit address and size cells and 32bit shifts in the code. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* block: Add support for Ceva sataMichal Simek2016-04-041-0/+4
| | | | | | | Initial Ceva Sata init code. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM64: zynqmp: Read RAM information from DTMichal Simek2016-04-041-0/+121
| | | | | | | | | | | | | | | Read information about memory from DT. This patch simplify life with synchronization between DT and board files. dram_init() only needs maximum RAM size below 4GB that's why please sort banks in memory node. dram_init_banksize() copies memory setup to bi_dram[]. This will avoid reading information from DT twice. Memory test start/end were changed to DDR location to let memtest still compiled. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: zynq: zynqmp: Line up checkboard messageMichal Simek2016-01-271-1/+1
| | | | | | | | | Use space instead of tab in checkboard print to aligned it with others boards. Reported-by: David Glessner <david.glessner@rockwellcollins.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
* ARM64: zynqmp: Remove unneeded timer_init functionMichal Simek2016-01-271-5/+0
| | | | | | Empty weak function is used instead. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Fix bootmode SD_MODE1Michal Simek2016-01-271-1/+4
| | | | | | | | | | | | | When only sdhci1 IP is enabled and SD_MODE1 bootmode is selected U-Boot using sdboot1 variable which refers to mmc dev 1. But this device doesn't exist because only one controller is available. This patch fix logic around sdboot mode with using sdbootdev internal variable. Reported-by: Chris Kohn <ckohn@xilinx.com> Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Differentiate EMMC boot modeMichal Simek2016-01-271-1/+4
| | | | | | | | Show also EMMC bootmode if selected. There is difference compare to SD bootmode. Use the same bootcommand till better boot command is created. Reported-by: Sai Pavan Boddu <saipava@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Show information about bootmodeMichal Simek2016-01-271-1/+7
| | | | | | | Showing information about bootmode is very useful to make sure that correct bootmode is selected. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Add support for SD1 boot modeMichal Simek2016-01-271-0/+6
| | | | | | | SD1 boot mode is using different bootmode values. Add support for this mode used on DC1. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Modify the SD and QSPI bootmode valuesSiva Durga Prasad Paladugu2016-01-271-0/+7
| | | | | | | | Modify the SD bootmode value to 0x3 as per latest spec. Also add new boot mode QSPI 32 bit boot mode Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Use the same U-Boot version with/without ATFMichal Simek2016-01-271-4/+13
| | | | | | | | Remove SECURE_IOU option which is not needed. U-Boot itself can detect which EL level it is on and based on that use do platform setup. It also simplify usage because one Kconfig entry is gone. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynq: sdhci: Move driver to DMMichal Simek2015-12-071-22/+0
| | | | | | | Move driver to DM Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* net: gem: Move driver to DMMichal Simek2015-12-071-25/+0
| | | | | | | | | | | | | - Enable DM_ETH by default for Zynq and ZynqMP - Remove board_eth_init code - Change miiphy_read function to return value instead of error code based on DM requirement - Do not enable EMIO DT support by default Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* zynqmp: usb: Add usb dwc3 driver support for zynqmpSiva Durga Prasad Paladugu2015-08-191-0/+28
| | | | | | | | | | Added usb dwc3 driver support for zynqmp this also supports the DFU and LTHOR to download the linux images on to RAM and cen be booted from those linux images. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* board: Xilinx: zynqmp: Define checkboard() functionSiva Durga Prasad Paladugu2015-08-191-0/+6
| | | | | | | Define checkboard() function for zynqMP Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynqmp: Show EL level where U-Boot runsMichal Simek2015-07-281-0/+2
| | | | | | Add one more print to make clear which EL level U-Boot runs. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: zynqmp: Wire up SATA for the boardMichal Simek2015-07-281-0/+10
| | | | | | Enable SATA for the ZynqMP targets. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: zynqmp: Wire up ethernet controllersMichal Simek2015-07-281-0/+25
| | | | | | Wire up ethernet controllers and enable MII and BOOTP options. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynqmp: Add support for EMMC bootmodeMichal Simek2015-04-291-0/+1
| | | | | | Add support for EMMC bootmode. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* zynqmp: Add support for emulation platform - VeloceMichal Simek2015-04-291-2/+6
| | | | | | | Add support for Veloce - zynqmp emulation platform. Platform doesn't support SDHCI. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* arm64: Add Xilinx ZynqMP supportMichal Simek2015-03-021-0/+90
Add basic Xilinx ZynqMP arm64 support. Serial and SD is supported. It supports emulation platfrom ep108 and QEMU. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com>
OpenPOWER on IntegriCloud