summaryrefslogtreecommitdiffstats
path: root/board/udoo/udoo.c
Commit message (Collapse)AuthorAgeFilesLines
* udoo: Fix the error handling in board_eth_init()Fabio Estevam2015-09-131-8/+11
| | | | | | | | | We should not return 0 on failure, so return a negative error code instead. Also centralize the error path so that is easier to follow. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* udoo: Switch to SPL supportvpeter42015-09-021-40/+55
| | | | | | | | | | | | | | | | | | | Currently we need to build one U-boot image for each of the udoo variants: quad and dual-lite. By switching to SPL we can support all two variants with a single binary. Based on the SPL for wandboard. Tested with OpenELEC (Open Embedded Linux Entertainment Center) on both boards. Signed-off-by: Peter Vicman <peter.vicman@gmail.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Peter Vicman <peter.vicman@gmail.com> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
* udoo: Add SATA support on uDoo Board.Giuseppe Pagano2013-12-171-0/+4
| | | | | | | | Add SATA support on uDoo Board. Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
* udoo: Fix watchdog during kernel boot.Giuseppe Pagano2013-11-281-0/+1
| | | | | | | | | | | | uDoo uses APX823-31W5 watchdog chip. Timeout is about 1.2 seconds. To disabled watchdog during kernel boot, WDI pin of that chip needs to be in "high impedance" state. I.mx6 gpio configuration does not contemplate tristate, so pin is set as input in high impedance. Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
* udoo: Add ethernet support (FEC + Micrel KSZ9031).Giuseppe Pagano2013-11-281-0/+140
| | | | | | | | | | Add Ethernet and networking support on uDoo board (FEC +phy Micrel KSZ9031). Ethernet speed is currently limited to 10/100Mbps. Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
* i.MX6DQ/DLS: replace pad names with their Linux kernel equivalentsEric Nelson2013-11-131-10/+10
| | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
* udoo: Add initial support for mx6q udoo boardFabio Estevam2013-10-171-0/+110
Add basic support for mx6q udoo board. For further information about Udoo board: http://www.udoo.org/ Tested booting a mainline device tree kernel and a Yocto rootfs from mmc. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
OpenPOWER on IntegriCloud