summaryrefslogtreecommitdiffstats
path: root/board/nvidia/dts
Commit message (Collapse)AuthorAgeFilesLines
* ARM: tegra: Whistler: remove unused USB aliasStephen Warren2012-10-291-1/+4
| | | | | | | | | | | Port USB1 on Whistler is intended as a device port for USB recovery. Whistler's DT currently contains an alias for this USB port, even though Whistler's config doesn't enable multiple USB controllers, so the alias is unused. Remove the unused alias for consistency for now. Similar, explicitly disable the port in the device tree too. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: Harmony: enable ULPI USB portStephen Warren2012-10-291-1/+2
| | | | | | | | | | | | The ULPI port is routed onto pins on the mini PCI Express connector. A standard breakout board may be used to access the port. * Add required DT entries to configure the ULPI port. * Setup up the ULPI pinmux in the board code. * Enable multiple USB controller and ULPI support in the board config. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: enable NAND on HarmonyStephen Warren2012-09-071-0/+10
| | | | | Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: fdt: Add NAND definitions to fdtSimon Glass2012-09-071-0/+10
| | | | | | | | Add a flash node to handle the NAND, including memory timings and page / block size information. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra20: rename tegra2 -> tegra20Allen Martin2012-09-014-3/+3
| | | | | | | | | | This is make naming consistent with the kernel and devicetree and in preparation of pulling out the common tegra20 code. Signed-off-by: Allen Martin <amartin@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: ventana: add own device tree, enable USBStephen Warren2012-07-071-0/+57
| | | | | | | | | | Add a device tree for Ventana; the Seaboard file no longer represents the HW present on Ventana. Enable USB on Ventana. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: harmony: add device tree supportStephen Warren2012-07-071-0/+57
| | | | | | | ... to enable USB host support, which enables Ethernet support. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: Whistler board supportStephen Warren2012-07-071-0/+67
| | | | | | | | | | | | | | | | | | | Whistler is a highly configurable Tegra evaluation and development board. This change adds support for the following specific configuration: E1120 motherboard E1108 CPU board E1116 PMU board The motherboard configuration switches are set as follows: SW1=0 SW2=0 SW3=5 S1/S2/S3/S4 all on, except S3 7/8 are off. Other combinations of daugher boards may work to varying degrees, but will likely require some SW adjustment. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: fdt: Add keyboard definitions for SeaboardAnton Staff2012-05-151-0/+27
| | | | | | | | Seaboard uses a QUERTY keyboard. We add key codes for this to enable key scanning to work. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: fdt: Add EMC data for Tegra2 SeaboardSimon Glass2012-05-151-0/+37
| | | | | | | | | | | | This adds timings for T20 and T25 Seaboards, using the bindings found here: http://patchwork.ozlabs.org/patch/132928/ We supply both full speed options for normal running, and half speed options for testing / development. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: i2c: Select I2C ordering for SeaboardSimon Glass2012-03-291-0/+18
| | | | | | | Select the port ordering for I2C on Seaboard. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: usb: fdt: Add USB definitions for Tegra2 SeaboardSimon Glass2012-03-291-0/+11
| | | | | | | | We set up two USB ports, one of which can be host or device. For some reason the kernel version does enable both ports. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: fdt: Add clock bindings for Tegra2 SeaboardSimon Glass2012-03-291-0/+27
| | | | | | | | | | | Add the definition of the oscillator clock frequency and the 32KHz clock. The latter is provided by a PMIC on I2C which we don't actually use at present, but we expect this definition to be used in the kernel and want to keep our .dts the same. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: fdt: Add device tree file for Tegra2 Seaboard from kernelSimon Glass2012-03-291-0/+36
This was taken from commit b48c54e2 at: git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
OpenPOWER on IntegriCloud