summaryrefslogtreecommitdiffstats
path: root/board/mpc8540eval
Commit message (Collapse)AuthorAgeFilesLines
* mpc8xxx: LCRR[CLKDIV] is sometimes five bitsTrent Piepho2008-12-191-1/+1
| | | | | | | | | | | | | | On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits instead of four. In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems. It should be safe as the fifth bit was defined as reserved and set to 0. Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV. Signed-off-by: Trent Piepho <tpiepho@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Jon Loeliger <jdl@freescale.com>
* Align end of bss by 4 bytesSelvamuthukumar2008-11-181-0/+1
| | | | | | | | | | Most of the bss initialization loop increments 4 bytes at a time. And the loop end is checked for an 'equal' condition. Make the bss end address aligned by 4, so that the loop will end as expected. Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
* Cleanup: fix "MHz" spellingWolfgang Denk2008-10-211-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Pass dimm parameters to populate populate controller optionsHaiying Wang2008-10-181-1/+4
| | | | | | | | | | | | | Because some dimm parameters like n_ranks needs to be used with the board frequency to choose the board parameters like clk_adjust etc. in the board_specific_paramesters table of the board ddr file, we need to pass the dimm parameters to the board file. * move ddr dimm parameters header file from /cpu to /include directory. * add ddr dimm parameters to populate board specific options. * Fix fsl_ddr_board_options() for all the 8xxx boards which call this function. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
* rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD2008-10-184-68/+68
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* rename CFG_ENV macros to CONFIG_ENVJean-Christophe PLAGNIOL-VILLARD2008-09-101-8/+8
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASHJean-Christophe PLAGNIOL-VILLARD2008-09-101-2/+2
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Moved initialization of TULIP Ethernet controller to board_eth_init()Ben Warren2008-09-021-0/+12
| | | | | | | | | | | | | | | | | | | Affected boards: cu824 bab7xx adciop dasa_sim mousse mpc8540eval musenki mvblue pcippc2/pcippc6 sbc8240 stxssa Removed initialization of the driver from net/eth.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* FSL DDR: Convert MPC8540EVAL to new DDR code.Kumar Gala2008-08-273-5/+83
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Fix some more print() format errors.Wolfgang Denk2008-07-111-3/+5
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Cleanup out-or-tree building for some boards (.depend)Wolfgang Denk2008-07-021-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Change initdram() return type to phys_size_tBecky Bruce2008-06-121-1/+1
| | | | | | | | | | | | | | | | | | | This patch changes the return type of initdram() from long int to phys_size_t. This is required for a couple of reasons: long int limits the amount of dram to 2GB, and u-boot in general is moving over to phys_size_t to represent the size of physical memory. phys_size_t is defined as an unsigned long on almost all current platforms. This patch *only* changes the return type of the initdram function (in include/common.h, as well as in each board's implementation of initdram). It does not actually modify the code inside the function on any of the platforms; platforms which wish to support more than 2GB of DRAM will need to modify their initdram() function code. Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc MPC8641HPCN. Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* 85xx/86xx: Move to dynamic mgmt of LAWsKumar Gala2008-06-111-3/+3
| | | | | | | | | | | With the new LAW interface (set_next_law) we can move to letting the system allocate which LAWs are used for what purpose. This makes life a bit easier going forward with the new DDR code. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com> Acked-by: Jon Loeliger <jdl@freescale.com> Acked-by: Becky Bruce <becky.bruce@freescale.com>
* Big white-space cleanup.Wolfgang Denk2008-05-211-4/+4
| | | | | | | | | | | This commit gets rid of a huge amount of silly white-space issues. Especially, all sequences of SPACEs followed by TAB characters get removed (unless they appear in print statements). Also remove all embedded "vim:" and "vi:" statements which hide indentation problems. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Remove all the search paths from the .lds files.Jason Wessel2008-04-171-1/+0
| | | | | | | The cross compiler is responsible for providing the correct libraries and the logic to find the linking libraries. Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* 85xx: Add the concept of CFG_CCSRBAR_PHYSKumar Gala2008-03-261-1/+1
| | | | | | | | | When we go to 36-bit physical addresses we need to keep the concept of the physical CCSRBAR address seperate from the virtual one. For the majority of boards CFG_CCSBAR_PHYS == CFG_CCSRBAR Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Remove erroneous or extra spd.h #includers.Jon Loeliger2008-03-051-4/+2
| | | | | | | | | | Many of the spd.h #includers don't need it, and wanted to have spd_sdram() declared instead. Since they didn't get that, some also had open coded extern declarations of it instead or as well. Fix it all up by using spd_sdram.h where needed. Signed-off-by: Jon Loeliger <jdl@freescale.com>
* 85xx: Convert MPC8540EVAL to new TLB setupKumar Gala2008-01-174-141/+79
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Use proper defines for PCI addressesKumar Gala2008-01-162-3/+3
| | | | | | | | We should be using the _MEM_PHYS for LAW and TLB setup and not _MEM_BASE. While _MEM_BASE & _MEM_PHYS are normally the same, _MEM_BASE should only be used for configuring the PCI ATMU. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: convert remaining 85xx boards over to use new LAW init codeKumar Gala2008-01-163-44/+55
| | | | | | | Converted ATUM8548, MPC8568 MDS, MPC8540 EVAL, and TQM85xx boards over to use new LAW init code. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Fix linker scripts: add NOLOAD atribute to .bss/.sbss sectionsWolfgang Denk2008-01-121-1/+1
| | | | | | | | | | | | | | | | | | | With recent toolchain versions, some boards would not build because or errors like this one (here for ocotea board when building with ELDK 4.2 beta): ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab] For many boards, the .bss section is big enough that it wraps around at the end of the address space (0xFFFFFFFF), so the problem will not be visible unless you use a 64 bit tool chain for development. On some boards however, changes to the code size (due to different optimizations) we bail out with section overlaps like above. The fix is to add the NOLOAD attribute to the .bss and .sbss sections, telling the linker that .bss does not consume any space in the image. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Reworked FSL Book-E TLB macros to be more readableKumar Gala2008-01-091-66/+66
| | | | | | | | | | | The old macros made it difficult to know what WIMGE and perm bits were set for a TLB entry. Actually use the bit masks for these items since they are only a single bit. Also moved the macros into mmu.h out of e500.h since they aren't specific to e500. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Stop using immap_t on 85xxKumar Gala2007-12-111-8/+4
| | | | | | | | In the future the offsets to various blocks may not be in same location. Move to using CFG_MPC85xx_*_ADDR as the base of the registers instead of getting it via &immap. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Stop using immap_t for guts offset on 85xxKumar Gala2007-12-111-1/+1
| | | | | | | | In the future the offsets to various blocks may not be in same location. Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers instead of getting it via &immap->im_gur. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Move "ar" flags to config.mk to allow for silent "make -s"Wolfgang Denk2006-10-091-1/+1
| | | | Based on patch by Mike Frysinger, 20 Jun 2006
* Add support for a saving build objects in a separate directory.Marian Balakowicz2006-09-011-8/+12
| | | | | | | | | | | | | | | | | | | | | Modifications are based on the linux kernel approach and support two use cases: 1) Add O= to the make command line 'make O=/tmp/build all' 2) Set environement variable BUILD_DIR to point to the desired location 'export BUILD_DIR=/tmp/build' 'make' The second approach can also be used with a MAKEALL script 'export BUILD_DIR=/tmp/build' './MAKEALL' Command line 'O=' setting overrides BUILD_DIR environent variable. When none of the above methods is used the local build is performed and the object files are placed in the source directory.
* (no commit message)Wolfgang Denk2005-12-121-0/+1
|
* Fix problems with ld version 2.16 (dot outside sections problem)Wolfgang Denk2005-08-311-0/+2
| | | | | Pointed out by Gerhard Jaeger, 31 Aug 2005; cf. http://sourceware.org/ml/binutils/2005-08/msg00412.html
* Fix style issues primarily in 85xx and 83xx boards.Jon Loeliger2005-08-011-30/+10
| | | | | | | | - C++ comments - Trailing white space - Indentation not by TAB - Excessive amount of empty lines - Trailing empty lines
* * Patch by Ron Alder, 11 July 2005Lunsheng Wang2005-07-296-0/+1576
Add Xianghua Xiao and Lunsheng Wang's support for the GDA MPC8540 EVAL board.
OpenPOWER on IntegriCloud