summaryrefslogtreecommitdiffstats
path: root/board/keymile/kmp204x
Commit message (Collapse)AuthorAgeFilesLines
* KM/IVM: remove ivm_read_eeprom(void)Valentin Longchamp2015-02-161-1/+1
| | | | | | | | | | This is not used anymore since the procedure was split into a simple read function and a later alaysis. The ivm_read_eeprom name is now used for the previous ivm_simple_read_eeprom function. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* 85xx/kmp204x: read the IVM eeprom earlierValentin Longchamp2015-02-161-1/+4
| | | | | | | | | | This allows to define the ethaddr env variable according to the the IVM content by reading the IVM in misc_init_r. Later, when HUSH is available the content read earlier is analyzed to populate some non env variables. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* fdt: Allow ft_board_setup() to report failureSimon Glass2014-11-211-1/+3
| | | | | | | | | | | | | | | | | | This function can fail if the device tree runs out of space. Rather than silently booting with an incomplete device tree, allow the failure to be detected. Unfortunately this involves changing a lot of places in the code. I have not changed behvaiour to return an error where one is not currently returned, to avoid unexpected breakage. Eventually it would be nice to allow boards to register functions to be called to update the device tree. This would avoid all the many functions to do this. However it's not clear yet if this should be done using driver model or with a linker list. This work is left for later. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
* kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada2014-09-131-3/+0
| | | | | | | | | | | | | | | | | | Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* kmp204x: reset the Zarlink clocking chips at power up onlyValentin Longchamp2014-08-201-4/+4
| | | | | | | | | | | | | | There is the requirement on the chassis's backplane that when the clocks have been enabled, they then should not disappear. Resetting the Zarlink clocking chips at unit reset violates this requirement because the backplane clocks are not supplied during the reset time. To avoid this side effect, both the Zarlink clocking chips are reset only at power up. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2014-08-063-0/+54
|\
| * kmp204x: prepare to use CPU watchdogBoschung, Rainer2014-08-011-0/+3
| | | | | | | | | | | | | | | | | | This patch configures the qrio to trigger a core reset on a CPU reset request. Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * kmp204x/qrio: support for setting the CPU reset request modeBoschung, Rainer2014-08-012-0/+22
| | | | | | | | | | | | | | | | | | To acheive this, the qrio_uprstreq() function that sets the UPRSTREQN flag in the qrio RESCNF reg is added. Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * kmp204x: set CPU watchdog reset reason flagBoschung, Rainer2014-08-011-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | Check the core timer status register (TSR) for watchdog reset, and and set the QRIO's reset reason flag REASON1[0] accordingly. This allows the appliction SW to identify the cpu watchdog as a reset reason, by setting the REASON1[0] flag in the QRIO. Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * kmp204x/qrio: prepare support for the CPU watchdog reset reasonBoschung, Rainer2014-08-012-0/+17
| | | | | | | | | | | | | | | | | | To achieve this, the qrio_cpuwd_flag() function that sets the CPU watchdog flag in the REASON1 reg is added. Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | Add board MAINTAINERS filesMasahiro Yamada2014-07-301-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have switched to Kconfig and the boards.cfg file is going to be removed. We have to retrieve the board status and maintainers information from it. The MAINTAINERS format as in Linux Kernel would be nice because we can crib the scripts/get_maintainer.pl script. After some discussion, we chose to put a MAINTAINERS file under each board directory, not the top-level one because we want to collect relevant information for a board into a single place. TODO: Modify get_maintainer.pl to scan multiple MAINTAINERS files. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
* | kconfig: add board Kconfig and defconfig filesMasahiro Yamada2014-07-301-0/+15
|/ | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* kmp204x: add workaround for A-004849Valentin Longchamp2014-05-131-6/+37
| | | | | | | | | | This should prevent the problems that the CCF can deadlock with certain traffic patterns. This also fixes the workaround for A-006559 that was not correctly implemented before. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* kmp204x: update the RCWValentin Longchamp2014-05-131-1/+1
| | | | | | | | Fix the IRQ/GPIO settings: all the muxed GPIO/external IRQs that are used as internal interrupts are defined as GPIOs to avoid confusion between the internal/external interrupts. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* kmp204x: complete the reset sequence and PRST configurationValentin Longchamp2014-05-134-19/+45
| | | | | | | | | | | | | | | | | | | | | This adds the reset support for the following devices that was until then not implemented: - BFTIC4 - QSFPs This also fixes the configuration of the prst behaviour for the other resets: Only the u-boot and kernel relevant subsystems are taken out of reset (pcie, ZL30158, and front eth phy). Most of the prst config move to misc_init_f(), except for the PCIe related ones that are in pci_init_board and the bftic and ZL30158 ones that should be done as soon as possible. Only the behavior of the Hooper reset is changed according to the documentation as the application is not able to not configure the switch when it is not reset. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* kmp204x: selftest/factory test pin supportValentin Longchamp2014-05-131-0/+13
| | | | | | | | | | | | | | | | | | | This patch defines the post_hotkeys_pressed() function that is used for: - triggering POST memory regions test - starting the test application through the checktestboot command in a script by setting the active bank to testbank The post_hotkeys_pressed return the state of the SELFTEST pin. The patch moves from the complete POST-memory test that is too long in its SLOW version for our production HW test procedure to the much shorter POST-memory-regions test. Finally, the unused #defines for the not so relevant mtest command are removed. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* kmp204x: handle dip-switch for factory settingsStefan Bigler2014-05-133-0/+30
| | | | | | | | | Add readout of dip-switch to revert to factory settings. If one or more dip-switch are set, launch bank 0 that contains the bootloader to do the required action. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* kmp204x: Add support for the unit LEDsStefan Bigler2014-05-133-0/+19
| | | | | | | | | | | | The unit LEDs are managed by the QRIO CPLD. This patch adds support for accessing these LEDs in the QRIO. The LEDs then are set to a correct boot state: - UNIT-LED is red - BOOT-LED is on. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* kmp204x: initial support for PCIe FPGA configurationValentin Longchamp2014-02-032-1/+91
| | | | | | | | | | | | | | The PEXHC PCIe configuration mechanism ensures that the FPGA get configured at power-up. Since all the PCIe devices should be configured when the kernel start, u-boot has to take care that the FPGA gets configured also in other reset scenarios, mostly because of possible configuration change. The used mechanism is taken from the km_kirkwood design and adapted to the kmp204x case (slightly different HW and PCIe configuration). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
* kmp204x: update I2C field of RCWValentin Longchamp2014-02-031-1/+1
| | | | | | | | | | | On the previous HW revision (now unsupported), there was a need for external DMA signals and thus the I2C3/4 signals were used DMA1_DONE/ACK/REQ. These signals now are configured as GPIO[16:19]. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
* kmp204x: implement workaround for A-006559Valentin Longchamp2014-02-031-0/+10
| | | | | | | | | | | | According to the errata, some bits of an undocumented register in the DCSR must be set for every core in order to avoid a possible data or instruction corruption. This is required for the 2.0 revision of the P2041 that should be used as soon as available in our design. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
* kmp204x: I2C deblocking supportRainer Boschung2014-02-031-3/+50
| | | | | | | | | | | | | | | | | | | | This patch adds support for using some GPIOs that are connected to the I2C bus to force the bus lines state and perform some bus deblocking sequences. The KM common deblocking algorithm from board/keymile/common/common.c is used. The GPIO lines used for deblocking the I2C bus are some external GPIOs provided by the QRIO CPLD: - SCL = GPIOA_20 - SDA = GPIOA_21 The QRIO GPIOs act in an open-drain-like manner, for 0 the line is driven low and for 1 the GPIO is set as input and the line gets pulled-up. Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
* kmp204x: introduce QRIO GPIO functionsValentin Longchamp2014-02-034-57/+157
| | | | | | | | | | | The QRIO GPIO functions can be of general interest. They are thus added to a qrio.c and their prototype are available from kmp204x.h. The QRIO prst function are also included in this file, as well as the functions required for the I2C deblocking support (open-drain). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: Remove extra blank line in board/keymile/kmp204x/qrio.c] Signed-off-by: York Sun <yorksun@freescale.com>
* kmp204x: support for QRIO1 bootcounterRainer Boschung2014-02-031-20/+0
| | | | | | | | | | Make use of the QRIO1 32bit register at 0x20 as bootcounter register Check for BOOTCOUNT_MAGIC pattern when before bootcounter value is read Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: Minor change to commit message] Signed-off-by: York Sun <yorksun@freescale.com>
* Driver/DDR: Moving Freescale DDR driver to a common driverYork Sun2013-11-251-2/+2
| | | | | | | Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs. The similar DDR controllers will be used for ARM-based SoCs. Signed-off-by: York Sun <yorksun@freescale.com>
* Makefile: make directories by Makefile.buildMasahiro Yamada2013-11-171-4/+0
| | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* Makefile: specifiy an explicite object name rather than $(BOARD).oMasahiro Yamada2013-11-171-1/+1
| | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* board/keymile/kmp204x/Makefile: Convert to SPDX tagTom Rini2013-11-011-14/+1
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* board: powerpc: convert more makefiles to Kbuild styleTom Rini2013-11-011-20/+1
| | | | | | | | Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: York Sun <yorksun@freescale.com> Signed-off-by: Tom Rini <trini@ti.com>
* mpc85xx: introduce the kmp204x reference design supportValentin Longchamp2013-10-2410-0/+687
This patch introduces the support for Keymile's kmp204x reference design. This design is based on Freescale's P2040/P2041 SoC. The peripherals used by this design are: - DDR3 RAM with SPD support - SPI NOR Flash as boot medium - NAND Flash - 2 PCIe busses (hosts 1 and 3) - 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5) - 3 Local Bus windows, with one dedicated to the QRIO reset/power mgmt FPGA - 2 HW I2C busses - last but not least, the mandatory serial port The board/keymile/kmp204x code is mostly based on Freescale's P2041rdb support and was changed according to our design (that means essentially removing what is not present on the designs and a few adaptations). There is currently only one prototype board that is based on this design and this patch also introduces it. The board is called kmlion1. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> kmp204x: update the ENV #define The comments had to be refined as well as the total size Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: fix ddr.c] Acked-by: York Sun <yorksun@freescale.com>
OpenPOWER on IntegriCloud