summaryrefslogtreecommitdiffstats
path: root/board/keymile/common
Commit message (Collapse)AuthorAgeFilesLines
* KM: add CONFIG_KM_COMMON_ETH_INIT for km common eth initValentin Longchamp2013-10-241-0/+2
| | | | | | | | | | | | This must be defined by a board support file that want to use the keymile common.c board_eth_init function that requires ethernet_present to be defined. Currently all the km architectures use it but the kmp204x architecture later supported in this series does use another board_eth_init function and thus does not define it. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* KM: define CONFIG_SYS_I2C_INIT_BOARD only for concerned boardValentin Longchamp2013-10-241-25/+0
| | | | | | | | | | | | | This must be defined for all the keymile boards that use the common i2c_abort function that is used to "reset" the I2C bus. These are currently km82xx and km_arm boards. The km83xx boards use other functions and thus do not need this. This patch removes the CONFIG_SYS_I2C_INIT_BOARD from keymile-common.h and defines it for km_arm.h and km82xx.h. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* Merge branch 'next' of git://git.denx.de/u-boot-mpc83xxTom Rini2013-10-092-4/+4
|\
| * powerpc/83xx/km: make local functions and structs staticHolger Brunck2013-05-212-4/+4
| | | | | | | | | | Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini2013-07-241-17/+2
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The sandburst-specific i2c drivers have been deleted, conflict was just over the SPDX conversion. Conflicts: board/sandburst/common/ppc440gx_i2c.c board/sandburst/common/ppc440gx_i2c.h Signed-off-by: Tom Rini <trini@ti.com>
| * | i2c, multibus, keymile: get rid of EEprom_ivm envvariableHeiko Schocher2013-07-231-5/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | as the keymile boards use now the new i2c multibus/multiadapter framework, remove the EEprom_ivm Environmentvar, as not longer needed. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Holger Brunck <holger.brunck@keymile.com> Tested-By: Holger Brunck <holger.brunck@keymile.com>
| * | i2c, fsl_i2c: switch to new multibus/multiadapter supportHeiko Schocher2013-07-231-16/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | - added to fsl_i2c driver new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@wwwdotorg.org>
| * | i2c, soft-i2c: switch to new multibus/multiadapter supportHeiko Schocher2013-07-231-1/+5
| |/ | | | | | | | | | | | | | | | | - added to soft_i2c driver new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@wwwdotorg.org>
* | Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-243-38/+3
|/ | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* powerpc/83xx/km: add MV88E6122 switch support for kmvect1Karlheinz Jerg2013-02-151-1/+7
| | | | | | | | | | | | | | | kmvect1 has a UEC2 connection to the piggy board and a UEC0 connection to the switch MV88E6122. This switch has a connection to a frontport ethernet interface. The ethernet port used for network booting is automatically selected by u-boot. If a Piggy is plugged, the Piggy port is selected (UEC2, eth1). If the Piggy isn't present, the Frontport is selected (UEC0, eth0). The switch reset is connected to a GPIO on the PRIO3 board FPGA (GPIO28) and released at startup. Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* km/common/ivm: rework piggy mac adress offset generationHolger Brunck2013-02-151-11/+17
| | | | | | | | | For the the kmvect1 board we will also need a functionality to add an offset to the IVMs MAC address, because these board will have two valid ethernet ports for debugging purpose. So move the code to an own function. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* km82xx, km83xx: move ethernet_present() from common to cpu specificKarlheinz Jerg2013-02-151-11/+0
| | | | | | | | For kmvect1 we need a special solution and for km_arm boards we already have. So move the common code to the architectur specific file. Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* km/common/ivm: remove CONFIG_SYS_I2C_IVM_BUS related codeHolger Brunck2013-02-151-4/+0
| | | | | | | This define isn't set within our setup files. So we can safely remove the affected code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* km/common/ivm: remove obsolete codeHolger Brunck2013-02-151-8/+0
| | | | | | | EEprom_ivm_addr isn't set in our environment, so remove the usage of this. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* km/common: remove unneeded ifdefs for I2CHolger Brunck2013-02-151-2/+0
| | | | | | | All boards from this serie use i2c. There is no need to #ifdef the header. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* km/common: cosmetic change reported from checkpatchHolger Brunck2013-01-091-1/+1
| | | | | | | Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
* km/ivm: fix string len check to support 7 char board namesValentin Longchamp2012-09-031-1/+1
| | | | | | | | | | | | | | | The fanless boards now have a 7-digit (XXXXX-F) board name. This triggers a border condition when reading this string in the IVM although this string is smaller than the currenly read string size, but only by 1 character. This patch corrects this by changing the size check condition for string length. It is the same change that was done in the platform for this same bug. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Stefan Bigler <stefan.bigler@keymile.com>
* km/common: remove printfs for i2c deblocking codeHolger Brunck2012-07-311-3/+0
| | | | | | | | | This code will also be used before reallocation and during this time we are not allowed to do these printings. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Prafulla Wadaskar <Prafulla@marvell.com> Acked-by: Heiko Schocher <hs@denx.de>
* arm/km: enable BOCO2 FPGA download supportValentin Longchamp2012-07-071-0/+5
| | | | | | | | | | | | | | | | | | | | | | | This adds a first support of the FPGA download for a PCIe FPGA based on the BOCO2 CPLD. This takes place in 3 steps, all done accessing the SPICTRL reg of the BOCO2: 1) start the FPGA config with an access to the FPGA_PROG bit 2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1 for the end of the FPGA configuration (with a timeout) 3) reset the FPGA 4) finally remove the access to its config EEPROM from the FPGA so that the CPU can update the FPGA configuration when the kernel is running The boards with a PCIe FPGA but without BOCO2 still are supported. The config option name is CONFIG_KM_FPGA_CONFIG Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* km/common: check test_bank and testpin for testbootThomas Herzmann2012-06-151-0/+36
| | | | | | | | | | If the testpin is asserted, first check if a test_bank variable is defined before trying to boot this test_bank. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* powerpc/83xx: configure CONFIG_POST for kmcoge5neThomas Herzmann2012-06-151-1/+5
| | | | | | | | | | kmcoge5ne starts the post tests if the testpin on the board was enabled. Currently it does simply a memory test. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* powerpc/83xx/km: added missing enable of application bufferStefan Bigler2012-06-151-0/+2
| | | | | | | | Enabled application buffers in uboot to allow application chipselect access in uboot. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* km/common: fixed error in ethaddr (1-byte-shift)Thomas Herzmann2012-06-151-1/+1
| | | | | | | | The MAC address begins at offset 1. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* powerpc/83xx: move km 83xx specific i2c code to km83xx_i2cHolger Brunck2011-11-032-65/+9
| | | | | | | | | The common code should be valid for more than one architecture. Therefore this code was reorganized and moved to the new file km83xx_i2c.c Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* km/common: remove obsolete header fileHolger Brunck2011-10-221-4/+0
| | | | | | | | This header is unneeded due to code which was removed in the past. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Wolfgang Denk <wd@denx.de>
* km/common: fix ramfs development targetAndreas Huber2011-10-221-2/+14
| | | | | | | | | | Calucations of PRAM needs to take into account the 'rootfssize'. Memory available to the linux kernel 'mem=' is in all cases set to the total memory size minus the pram size. Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Wolfgang Denk <wd@denx.de>
* km/common: force set ethaddr only for KM kirkwood boardsHolger Brunck2011-10-221-0/+5
| | | | | | | | This prevents u-boot to print out "Can't overwrite "ethaddr"" each time a powerpc board starts. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Wolfgang Denk <wd@denx.de>
* km/common: fix bug in IVM mac address accessHolger Brunck2011-09-211-2/+2
| | | | | | | | The MAC address stored in the inventory eeprom begins at offset 1. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Wolfgang Denk <wd@denx.de>
* km/common: i2c deblock: enabled print of i2c deblock statusStefan Bigler2011-07-281-0/+3
| | | | | | | | | | Enable printout of i2c deblocking status if chips were in block state or deblocking failed. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: add printings to boardid commandsHolger Brunck2011-07-281-1/+5
| | | | | | | | | | Be verbose if do_setboardid was called and print correct names of variables in do_checkboardidhwk. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* powerpc/km82xx: remove 82xx specific functions from common.cHolger Brunck2011-07-272-68/+2
| | | | | | | | | | Common code should be valid for more than one architecture, therefore the km82xx specific code was removed from common.c. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: remove fdt_(gs)et_node_and_valueHolger Brunck2011-07-271-55/+0
| | | | | | | | | This code is unused and therefore dead code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: move ivm functions from to ivm.cHolger Brunck2011-07-273-318/+349
| | | | | | | | | | The file common.c grows in the past. So move the IVM specific code into an ivm.c file. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: remove saveenv from do_checkboardidhwkeyHolger Brunck2011-07-271-6/+1
| | | | | | | | | | | This is unneeded here because we save the environment when the board boots the first time. At this time we have set the values already. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: force set ethaddr after reading IVMHolger Brunck2011-07-271-2/+1
| | | | | | | | | | | | | | The ethaddr is stored inside the inventory eeprom. During boottime this value was read out and the ethaddr variable was set. Previously this was only done if it ethaddr == NULL but this is wrong for our ARM boards. Because ethaddr is at this stage never NULL for ARM due to the random calculation of a MAC address in mvgbe.c. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: remove obsolete defines and headerHolger Brunck2011-07-271-129/+0
| | | | | | | | | | These defines and the header keymile_hdlc_enet.h are obsolete due to the removed hdlc code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: implement boardId HWkey checks as u-boot cmdThomas Herzmann2011-05-181-0/+156
| | | | | | | | | | | | | | | | | | | | | | | | BoardId and HWKey are used to identify the HW class of a given board. The correct values are stored in the inventory eeprom. During creation time of a boot package the boardId and HWkey for the SW is stored in the default environment and burned into the flash. During boottime the values in the inventory and in the environment are compared to avoid starting of a SW which is not authorized for this board. Some bootpackages are allowed to run on a set of different boardId hwKey. In this case the environment variable boardIdListHex was added to the default environment. In this case the command iterates over the pair values and compares them with the values read from the inventory eeprom. The syntax of such a boardIdListHex value is e.g.: 158_1 159_1 159_2 Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de>
* km/common: implement setboardid commandHolger Brunck2011-05-101-0/+34
| | | | | | | | | | | Read out board id and HW key from the IVM eeprom and set these values as an environment variable. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* powerpc/km82xx: add mgcoge3ne and remove mgcoge2ne supportHolger Brunck2011-05-102-3/+4
| | | | | | | | | | | | | | | | | This patch adds support for the MPC8247 based board mgcoge3ne. Additionaly mgcoge2ne board supprot was removed, because due to the mgcoge3ne, this board is obsolete and not longer maintained. The board is similar to mgcoge. The difference is that a NUMONYX flash is used and a different SDRAM (256MB). Also introduce CONFIG_KM_82XX to collect ppc82xx common settings and remove staticness from the common set_pin function. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de>
* powerpc/km82xx: rework DIP switch detectionHuber, Andreas2011-05-101-0/+79
| | | | | | | | | | | | | Introduce a struct for the BFTICU FPGA to increase the readability of the code. And the define CONFIG_SYS_BFTICU_BASE was removed because the CONFIG_SYS_FPGA_BASE is already the base value for BFTICU registers. Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de>
* km/common: remove hdlc_enet implementationHolger Brunck2011-05-103-627/+0
| | | | | | | | | | | | | The hdlc implementation for mgcoge was initially developed, but later on not used. Remove the C files, the references in mgcoge.c and the Makefile to decrease maintenance effort. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* keymile, common: add setting of some environment variablesHeiko Schocher2011-04-302-0/+37
| | | | | | | | | | | | | This patch adds last_stage_init to all keymile boards. And in the last stage init some environment variables for u-boot were set. Currently these are pnvramaddr, pram and var address. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Wolfgang Denk <wd@denx.de> cc: Kim Phillips <kim.phillips@freescale.com>
* keymile boards: add CONFIG_PIGGY_MAC_ADRESS_OFFSETHeiko Schocher2011-04-302-0/+17
| | | | | | | | | | | | Normaly the PIGGY_MAC_ADRESS can be read directly from the IVM on keymile boards. On mgcoge3 it differs. Because there are two piggy boards deployed the second MAC adress must be calculated with the IVM mac adress and an offset. This patch allows to set such a offset in the board config. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de>
* keymile, common; fix i2c deblocking supportHeiko Schocher2011-04-301-32/+89
| | | | | | | | | | | | | | | | | | This patch fix the i2c deblocking facility with the i2c HW-Controller. The required delays for byte reading, the enhanced criteria for stop the dummy read and required 5 start/stop sequences are added. Add i2c deblocking before ivm eeprom read. Improve i2c deblocking sequence by respecting stop hold time. Cleaned function for deblocking. Have now one function i2c_make_abort() available for bitbang, mpc82xx and mpc83xx harware controller. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* ppc, 8321: cleanup tuxa1, tuda1 and suvd3 supportHeiko Schocher2011-04-301-1/+2
| | | | | | | | | | | | | | | | | | | | | For the kmsupx5 a new header file was introduced km8321-common.h. Now the common stuff from tuxa1, tuda1 and suvd3 was removed and the new header file included. The defines CONFIG_SYS_PIGGY_BASE and CONFIG_SYS_PIGGY_SIZE are confusing. Because they actually describe the KMBEC FPGA values. The KMBEC FPGA can be PRIO on kmeter1 or upio on mgcoge. Therefore all the defines were renamed. remove unneeded variable CONFIG_KM_DEF_NETDEV, as it is already declared in keymile-common.h Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Wolfgang Denk <wd@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* ppc: add support for ppc based board mgcoge2neHeiko Schocher2011-04-301-2/+2
| | | | | | | | | | | | | | | | | The mgcoge2 board from keymile deploys two different processors. An ARM based Kirkwood for the "unit" part of the SW and a PPC for the "ne" part of the SW. Therefore in Linux and U-Boot the names for the board are mgcoge2un and mgcoge2ne. This patch adds the mgcoge2ne part of the board. The ppc part of mgboge2 is quite similar to mgcoge, therefore a generic header km82xx-common.h was introduced to collect all similiarities. Currently the only difference is that mgcoge2ne has a 64 MB numonyx NOR flash with a single die. The mgcoge has a dual die flash 2*32MB from spansion. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* mpc832x: add support for the mpc8321 based suvd3 boardHeiko Schocher2011-04-301-4/+6
| | | | | | | | | | | | | | | | | | | | - serial console on UART1 - Ethernet RMII over UCC4 - PHY SMSC LAN8700 - 64MB Flash - 128 MB DDR2 RAM - I2C - bootcount This board is similiar to the kmeter1 (8360) board, so common config options are extracted into the include/configs/km83xx-common.h file. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* keymile: Fix Coding style issues for keymile boards.Heiko Schocher2011-04-302-188/+199
| | | | | | | | | | | | | | | | | | | - use I/O accessors -> For accessing the FPGA therefore a struct km_bec_fpga is introduced. - no longer externs needed - to defines, that only select functions, don;t assign a numeric value - Codingstyle changes to prevent checkpatch errors/warnings Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm, keymile: rename MACH_SUEN3 to MACH_KM_KIRKWOODHolger Brunck2011-04-301-2/+2
| | | | | | | | | | | | The MACH_TYPE SUEN3 is now to specific for keymile boards, because other boards similar to suen3 will follow. So the MACH_SUEN3 was renamed to MACH_KM_KIRKWOOD. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* net ppc: fix ethernet device names with spacesHeiko Schocher2010-08-091-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | since commit 1384f3bb8a4f9066805b70c1418eda78ecb73fdd ethernet names with spaces drop a Warning: eth device name has a space! message. This patch fix it for: - "FEC ETHERNET" devices found on mpc512x, mpc5xxx, mpc8xx and mpc8220 boards. renamed to "FEC". - "SCC ETHERNET" devices found on mpc8xx, mpc82xx based boards. Renamed to "SCC". - "HDLC ETHERNET" devices found on mpc8xx boards Renamed to "HDLC" - "FCC ETHERNET" devices found on mpc8260 and mpc85xx based boards. Renamed to "FCC" Tested on the kup4k board. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
OpenPOWER on IntegriCloud