summaryrefslogtreecommitdiffstats
path: root/board/freescale/b4860qds
Commit message (Collapse)AuthorAgeFilesLines
* B4860QDS: Enable enet port as per fsl_b4860_serdes2 string in hwconfigSuresh Gupta2014-12-051-0/+19
| | | | | | | | | | | | In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp respectively in hwconfig. Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/b4860qds: add workaround for XFIShaohui Xie2014-12-051-0/+13
| | | | | | | | | | | | | | | XFI does not work stable on current board, it's due to heat sink issue, to make it work stable the board needs additional heat sink, enable two XFI lanes only. Right now we do not have such an erratum for the issue, so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it. The workaround will only be used in XFI protocols and only if the hwconfig indicates that XFI is prefered. A new VSC3308 config function is used instead of re-use the original function, to avoid making the function complex and ugly. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* B4860QDS: Enable SFP or AMC on basis of hwconfig stringSuresh Gupta2014-12-051-8/+33
| | | | | | | | | | | | | SerDes2 lanes EFGH either go to SFP or AMC riser card slot2. By default AMC will be configured even if no hwconfig is specified. To enable XFI via SFP use the below hwconfig: fsl_b4860_serdes2:sfp_amc=sfp Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@ffeescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/b4860qds: dtb fixup for xfiShaohui Xie2014-12-051-0/+38
| | | | | | | | Since xfi has no phy, we delete the property "phy-handle" and use a "fixed-link" property for a xfi port. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/b4860qds: add xfi supportShaohui Xie2014-12-052-7/+39
| | | | | | | | | | We need following changes to make xfi work on B4: 1. set cross-point switch VSC3308 to use sfp config when running xfi; 2. add 10G interface check for xfi; 3. set phy address for xfi so the 10G ports can be registered by mdio; Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* B4860: Add alternate LC VCO serdes protocols support in board fileShaveta Leekha2014-12-051-0/+13
| | | | | | | | | Add the support of newly added LC VCO SerDes protocols for configuration of IDT and VSC crossbar Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* B4860QDS: SGMII related updatesShaveta Leekha2014-12-051-26/+38
| | | | | | | | | | | | | | - Enable SGMII support for 0x8d Serdes 2 protocol. - Correct Phy address for DTSECx for 0x8d/0xb2 Serdes 2 protocol. - Updated debug statement - Add Alternate LC VCO protocols(0x8d-->0x8c, 0xb2-->0xb1) - Rename onboard PHY address defines for more readability - Add these new Defines in B4860QDS.h file Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/b4860: Enable law creation of MAPLEShaveta Leekha2014-12-052-3/+8
| | | | | | | | | B4860, B4440, B4420 and B4220 have MAPLE, so enable law creation for them only. Remove static LAW creation for MAPLE. Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* fdt: Allow ft_board_setup() to report failureSimon Glass2014-11-211-1/+3
| | | | | | | | | | | | | | | | | | This function can fail if the device tree runs out of space. Rather than silently booting with an incomplete device tree, allow the failure to be detected. Unfortunately this involves changing a lot of places in the code. I have not changed behvaiour to return an error where one is not currently returned, to avoid unexpected breakage. Eventually it would be nice to allow boards to register functions to be called to update the device tree. This would avoid all the many functions to do this. However it's not clear yet if this should be done using driver model or with a linker list. This work is left for later. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
* MAINTAINERS: comment out blank M: fieldMasahiro Yamada2014-09-241-1/+1
| | | | | | | | | | | | | | | | | | Since commit ddaf5c8f3030050fcd356a1e49e3ee8f8f52c6d4 (patman: RunPipe() should not pipe stdout/stderr unless asked), Patman spits lots of "Invalid MAINTAINERS address: '-'" error messages for patches with global changes. It takes too long for Patman to process them. Anyway, "M: -" does not carry any important information. Rather, it is just like a place holder in case of assigning a new board maintainer. Let's comment out. This commit can be reproduced by the following command: find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada2014-09-131-3/+0
| | | | | | | | | | | | | | | | | | Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* Add board MAINTAINERS filesMasahiro Yamada2014-07-301-0/+17
| | | | | | | | | | | | | | | | | | | | We have switched to Kconfig and the boards.cfg file is going to be removed. We have to retrieve the board status and maintainers information from it. The MAINTAINERS format as in Linux Kernel would be nice because we can crib the scripts/get_maintainer.pl script. After some discussion, we chose to put a MAINTAINERS file under each board directory, not the top-level one because we want to collect relevant information for a board into a single place. TODO: Modify get_maintainer.pl to scan multiple MAINTAINERS files. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
* kconfig: add board Kconfig and defconfig filesMasahiro Yamada2014-07-301-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* powerpc/mpc85xx: Check return value of find_tlb_idxYork Sun2014-07-221-3/+9
| | | | | | | | | | find_tlb_idx() is called in board_early_init_r() on multiple boards. The return value is not checked before being used to disable a TLB. In normal case the return value wouldn't be -1. In case of a mis- configuration during porting to a new board, checking the return value may be helpful to reveal some user errors. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/B4420: Fixed incomplete handling for 0x9d serdes2poonam aggrwal2014-06-051-0/+6
| | | | | | | | | Crossbars and IDT were not getting configured for Serdes2 protocol 0x9d for B4420. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/b4qds: VID supportShaveta Leekha2014-05-131-0/+240
| | | | | | | | | | | | | | | | | | The fuse status register provides the values from on-chip voltage ID efuses programmed at the factory. These values define the voltage requirements for the chip. u-boot reads FUSESR and translates the values into the appropriate commands to set the voltage output value of an external voltage regulator. B4860QDS has a PowerOne ZM7300 programmable digital Power Manager which is programmed as per the value read from the fuses. Reference for this code is taken from t4qds VID implementation. Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
* board/b4qds:Add support of 2 stage NAND boot-loaderPrabhakar Kushwaha2014-04-224-3/+135
| | | | | | | | | | | | | | Add support of 2 stage NAND boot loader using SPL framework. here, PBL initialise the internal SRAM and copy SPL(160KB). This further initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR. Finally SPL transer control to u-boot. Initialise/create followings required for SPL framework - Add spl.c which defines board_init_f, board_init_r - update tlb and ddr accordingly Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/b4860qds:Slow MDC clock to comply IEEE specs in PBI configPrabhakar Kushwaha2014-04-221-0/+3
| | | | | | | | | | The MDC generate by default value of MDIO_CLK_DIV is too high i.e. higher than 2.5 MHZ. It violates the IEEE specs. So Slow MDC clock to comply IEEE specs Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/b4860: Add workaround for errata A006384 and A006475Shaveta Leekha2014-03-071-0/+193
| | | | | | | | | | | | | SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384) and at cold temperatures(A006475), workaround recalibrate the PLLs with some SerDes configuration Both these errata are only applicable for b4 rev1. So, make workaround for these errata conditional, depending upon soc version. Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* B4860qds: Set SerDes2 refclk2 at to 156.25MHz for XFI to workShaveta Leekha2014-03-071-4/+3
| | | | | | | | | | Change setting of SerDes2 refclk2 to have the default value as it is coming on board that is 156.25MHz, for XFI to work. Also change PLL_NUM variable to the one defined in config_mpc85xx.h for B4860 and B4420. Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* 85xx/b4860: Alternate serdes protocols for B4860/B4420poonam aggrwal2014-03-072-0/+7
| | | | | | | | | | | | | | | On B4860 and B4420, some serdes protocols can be used with LC VCO as well as Ring VCO options. Addded Alternate options with LC VCO for such protocols. For example protocol 0x2a on srds 1 becomes 0x29 if it is LC VCO. The alternate option has the same functionality as the original option; the only difference being LC VCO rather than Ring VCO. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/b4860qds: Add support to make PCIe SATA work on B4860QDSShaveta Leekha2014-03-071-9/+110
| | | | | | | | | | | | 1) SerDes2 Refclks have been set properly to make PCIe SATA to work as it work on SerDes refclk of 100MHz 2) Mask the SerDes's device reset request before changing the Refclks for SerDes1 and SerDes2 for PLL locks to happen properly, device reset request bit unmasked after SerDes refclks configuration Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/b4860qds: Add support to make Aurora work on B4860QDSShaveta Leekha2014-03-072-4/+79
| | | | | | | | | | | | | 1) Add new SerDes1 protocols having Aurora in them 2) Add VSC cross point connections for Aurora to work with CPRI and SGMIIs 3) Configure VSC crossbar switch to connect SerDes1 lanes to aurora on board, by checking SerDes1 protocols 4) SerDes1 Refclks have been set properly to make Aurora, CPRI and SGMIIs to work together properly Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/b4860/pbl: fix rcw cfgShaohui Xie2014-01-021-1/+1
| | | | | | The BOOT_LOC setting in rcw cfg is wrong, set it to Memory complex 1. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
* Driver/DDR: Moving Freescale DDR driver to a common driverYork Sun2013-11-251-3/+3
| | | | | | | Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs. The similar DDR controllers will be used for ARM-based SoCs. Signed-off-by: York Sun <yorksun@freescale.com>
* board: powerpc: convert makefiles to Kbuild styleMasahiro Yamada2013-11-011-32/+6
| | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Stefan Roese <sr@denx.de>
* fsl/mpc85xx: define common serdes_clock_to_string functionValentin Longchamp2013-10-241-16/+0
| | | | | | | | | | | | This allows to share some common code for the boards that use a corenet base SoC. Two different versions of the function are available in fsl_corenet_serdes.c and fsl_corenet2_serdes.c files. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: fix t1040qds.c] Acked-by: York Sun <yorksun@freescale.com>
* powerpc: Fix CamelCase warnings in DDR related codePriyanka Jain2013-10-161-16/+16
| | | | | | | | | | | Some DDR related structures present in fsl_ddr_dimm_params.h, fsl_ddr_sdram.h, ddr_spd.h has various parameters with embedded acronyms capitalized that trigger the CamelCase warning in checkpatch.pl Convert those variable names to smallcase naming convention and modify all files which are using these structures with modified structures. Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
* powerpc/B4860: enable PBL tool for B4860Shaohui Xie2013-10-162-0/+34
| | | | | | | | Use a default RCW of protocol 0x2A_0x98, and a PBI configure file which uses CPC1 as 512KB SRAM, then PBL tool can be used on B4860 to build a pbl boot image. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
* SGMII:fix PHY addresses for QSGMII Riser Card working in SGMII modeZhao Qiang2013-10-162-0/+23
| | | | | | | | | | | | | | | | | | | | | Fix PHY addresses for QSGMII Riser Card working in SGMII mode on board P3041/P5020/P4080/P5040/B4860. QSGMII Riser Card can work in SGMII mode, but having the different PHY addresses. So the following steps should be done: 1. Confirm whether QSGMII Riser Card is used. 2. If yes, set the proper PHY address. Generally, the function is_qsgmii_riser_card() is for step 1, and set_sgmii_phy() for step 2. However, there are still some special situations, take P5040 and B4860 as examples, the PHY addresses need to be changed when serdes protocol is changed, so it is necessary to confirm the protocol before setting PHY addresses. Signed-off-by: Zhao Qiang <B45475@freescale.com>
* Coding Style cleanup: replace leading SPACEs by TABsWolfgang Denk2013-10-141-1/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Drop changes for PEP 4 following python tools] Signed-off-by: Tom Rini <trini@ti.com>
* powerpc/common/vsc3316: remove const from vsc3316_config parameter defineShaohui Xie2013-08-201-6/+6
| | | | | | | | | Since the parameters need to be modified according to different Serdes protocols at runtime, the const will block this. Also remove const from arrays define used by vsc3316_config. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* board/b4860qds: Add support for configuring SerDes1 RefclksShaveta Leekha2013-08-092-2/+112
| | | | | | | | | | | | | | | | | | 1) Add support in B4860 board files for using IDT driver where IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer that generate different refclks for SerDes modules, used this driver for reconfiguring SerDes1 Refclks(based on SerDes1 protocols) for CPRI to work. CPRI works on 122.88MHz and default refclks coming on board are not suitable for it 2) Move SerDes1 refclk1 source selection from eth_b4860qds.c file to b4860qds board file, as SerDes1 Refclk1 would come from PHY MUX in case of certain protocols, that have been checked here. This change would make on board SGMIIs to work 3) Add I2C addresses for IDT8T49N222A devices in board/include file 4) Add define for PCA-I2C bus multiplexer, on which IDT devices exist Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc/corenet: Move RCW print to cpu.cYork Sun2013-08-091-15/+0
| | | | | | | The RCW print is common for all corenet platforms. Not necessary to ducplicate in each board file. Signed-off-by: York Sun <yorksun@freescale.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-249-144/+9
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* powerpc/b4860qds: Slave module for boot from SRIO and PCIELiu Gang2013-06-201-0/+19
| | | | | | | | | | | | | | | | | | | | | | When a b4860qds board boots from SRIO or PCIE, it needs to finish these processes: 1. Set all the cores in holdoff status. 2. Set the boot location to one PCIE or SRIO interface by RCW. 3. Set a specific TLB entry for the boot process. 4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot. 5. Set a specific TLB entry in order to fetch ucode and ENV from master. 6. Set a LAW entry with the TargetID one of the PCIE ports for ucode and ENV. 7. Slave's u-boot image should be generated specifically by make xxxx_SRIO_PCIE_BOOT_config. This will set SYS_TEXT_BASE=0xFFF80000 and other configurations. For more information about the feature of Boot from SRIO/PCIE, please refer to the document doc/README.srio-pcie-boot-corenet. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/b4860qds: Add LAW Target ID and Create LAW entry for MapleShaveta Leekha2013-05-241-0/+3
| | | | | Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/b4860: fix for Serdes connectivity to SFP'sShaveta Leekha2013-05-242-12/+25
| | | | | | | | | | Crossbar switches were wrongly programmed to route the CPRI lanes to SFP as the connectivity table was not correct. Modified it correctly for SFPs connections. Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Enable XAUI interface for B4860QDSSuresh Gupta2013-05-241-0/+35
| | | | | | | | | | | | | - Added SERDES2 PRTCLs = 0x98, 0x9E - Default Phy Addresses for Teranetics PHY on XAUI card The PHY addresses of Teranetics PHY on XAUI riser card are assigned based on the slot it is in. Switches SW4[2:4] and SW6[2:4] on AMC2PEX-2S On B4860QDS, AMC2PEX card decide the PHY addresses on slot1 and slot2 - Configure MDIO for 10Gig Mac Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* board/t4240qds, b4860qds: LAW/TLB for DCSR set to size 32MStephen George2013-05-242-2/+3
| | | | | | | Debug trace buffers are memory mapped in DCSR space beyond 4M. Signed-off-by: Stephen George <stephen.george@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/b4860qds: Assign DDR address in board fileYork Sun2013-05-141-0/+72
| | | | | | | | B4860QDS requires DDRC2 has 0 as base address and DDRC1 has higher address. This is the requirement for DSP cores to run in 32-bit address space. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/b4860qds: Add the tlb entries for SRIO interfacesLiu Gang2013-05-021-2/+17
| | | | | | | | | | | | | | Add the tlb entries based on the configuration of the SRIO interfaces. Every SRIO interface has 256M space: #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* ppc: Move lbc_clk and cpu to arch_global_dataSimon Glass2013-02-041-1/+1
| | | | | | | | Move these fields into arch_global_data and tidy up. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Update for bsc9132qds.c, b4860qds.c] Signed-off-by: Tom Rini <trini@ti.com>
* powerpc/b4860qds: Add support to dump switch settings on b4860qds boardShaveta Leekha2013-01-301-0/+47
| | | | | | | | | | This function is called by "qixis_reset switch" command and switch settings are calculated from FPGA/qixis registers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/b4860qds: Added Support for B4860QDSYork Sun2013-01-3010-0/+1380
B4860QDS is a high-performance computing evaluation, development and test platform supporting the B4860 QorIQ Power Architecture processor. B4860QDS Overview ------------------ - DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 4 GB of memory in two ranks of 2 GB. - DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB of memory. Single rank. - SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point 16x16 switch VSC3316 - SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point 8x8 switch VSC3308 - USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode. - B4860 UART port is available over USB-to-UART translator USB2SER or over RS232 flat cable. - A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA connector ports 0 and 2 for AMC mode. - The B4860 configuration may be loaded from nine bits coded reset configuration reset source. The RCW source is set by appropriate DIP-switches: - 16-bit NOR Flash / PROMJet - QIXIS 8-bit NOR Flash Emulator - 8-bit NAND Flash - 24-bit SPI Flash - Long address I2C EEPROM - Available debug interfaces are: - On-board eCWTAP controller with ETH and USB I/F - JTAG/COP 16-pin header for any external TAP controller - External JTAG source over AMC to support B2B configuration - 70-pin Aurora debug connector - QIXIS (FPGA) logic: - 2 KB internal memory space including - IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK, DDRCLK1, 2 and RTCCLK. - Two 8T49N222A SerDes ref clock devices support two SerDes port clocks - total four refclk, including CPRI clock scheme Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
OpenPOWER on IntegriCloud