summaryrefslogtreecommitdiffstats
path: root/board/atmel/at91sam9261ek
Commit message (Collapse)AuthorAgeFilesLines
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-244-66/+4
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* arm:at91-boards: remove console_init_f where unnecessaryAndreas Bießmann2012-09-011-3/+0
| | | | | | | | | | | | | | | | A lot of at91 boards have the console_init_f in board_init. This is useless cause it was called before by generic code in lib/board.c. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> cc: Jens Scharsig <esw@bus-elektronik.de> cc: Stelian Pop <stelian@popies.net> cc: Sedji Gaouaou<sedji.gaouaou@atmel.com> cc: Albin Tonnerre <albin.tonnerre@free-electrons.com> cc: Eric Benard <eric@eukrea.com> Tested-by: voice.shen@atmel.com Tested-by: voice.shen@atmel.com Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
* AT91SAM9*: Change kernel address in dataflash to match u-boot's sizeAlexandre Belloni2012-07-071-3/+3
| | | | | | | | | | | | | | | | | | | | | | | On at91sam platforms, u-boot grew larger than the allocated size in dataflash, the layout was: bootstrap 0x00000000 ubootenv 0x00004200 uboot 0x00008400 kernel 0x00042000 fs 0x00252000 u-boot with the defconfig doesn't seem to fit in 0x42000 - 0x8400 = 0x39C00 bytes anymore. Now, the layout is: bootstrap 0x00000000 ubootenv 0x00004200 uboot 0x00008400 kernel 0x00084000 fs 0x00294000 Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* Fix Stelian's email addressStelian Pop2011-11-293-3/+3
| | | | | | | Change my old email address which is no longer valid. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Anatolij Gustschin <agust@denx.de>
* punt unused clean/distclean targetsMike Frysinger2011-10-151-6/+0
| | | | | | | | | | The top level Makefile does not do any recursion into subdirs when cleaning, so these clean/distclean targets in random arch/board dirs never get used. Punt them all. MAKEALL didn't report any errors related to this that I could see. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* AT91: Board fix for AT91SAM9261-EKXu, Hong2011-08-033-67/+77
| | | | | | | Fix board part of AT91SAM9261-EK according to the new scheme Signed-off-by: Hong Xu <hong.xu@atmel.com> Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
* Switch from archive libraries to partial linkingSebastien Carlier2010-11-171-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Before this commit, weak symbols were not overridden by non-weak symbols found in archive libraries when linking with recent versions of binutils. As stated in the System V ABI, "the link editor does not extract archive members to resolve undefined weak symbols". This commit changes all Makefiles to use partial linking (ld -r) instead of creating library archives, which forces all symbols to participate in linking, allowing non-weak symbols to override weak symbols as intended. This approach is also used by Linux, from which the gmake function cmd_link_o_target (defined in config.mk and used in all Makefiles) is inspired. The name of each former library archive is preserved except for extensions which change from ".a" to ".o". This commit updates references accordingly where needed, in particular in some linker scripts. This commit reveals board configurations that exclude some features but include source files that depend these disabled features in the build, resulting in undefined symbols. Known such cases include: - disabling CMD_NET but not CMD_NFS; - enabling CONFIG_OF_LIBFDT but not CONFIG_QE. Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
* Rename TEXT_BASE into CONFIG_SYS_TEXT_BASEWolfgang Denk2010-10-181-1/+1
| | | | | | | | | | | | The change is currently needed to be able to remove the board configuration scripting from the top level Makefile and replace it by a simple, table driven script. Moving this configuration setting into the "CONFIG_*" name space is also desirable because it is needed if we ever should move forward to a Kconfig driven configuration system. Signed-off-by: Wolfgang Denk <wd@denx.de>
* ARM change name of defines for AT91 arm926ejsAchim Ehrlich2010-03-071-1/+1
| | | | | | | | | | Configuration defines should be preceeded with CONFIG_SYS_. Renamed some at91 specific defines to conform to this naming convention: AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>
* at91sam9261ek.c: fix minor coding style issue.Wolfgang Denk2009-12-071-4/+5
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* at91: Introduction of at91sam9g10 SOC.Sedji Gaouaou2009-07-121-0/+36
| | | | | | | AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a faster clock speed: 266/133MHz. Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
* Convert DM9000 driver for CONFIG_NET_MULTIRemy Bohmer2009-06-151-0/+7
| | | | | | | | | All drivers need to be converted to CONFIG_NET_MULTI. This patch converts the dm9000 driver. Signed-off-by: Thomas Smits <ts.smits@gmail.com> Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* at91sam9/at91cap: improve clock frameworkJean-Christophe PLAGNIOL-VILLARD2009-04-161-1/+2
| | | | | | calculate dynamically the clock rate and pllb setting for usb Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move nand drivers to drivers/mtd/nandJean-Christophe PLAGNIOL-VILLARD2009-03-223-81/+2
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* atmel/at91/boards: compile dataflash partition only when dataflash isJean-Christophe PLAGNIOL-VILLARD2009-03-221-1/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move common led management to cpuJean-Christophe PLAGNIOL-VILLARD2009-03-221-41/+6
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move common spi initialisation to cpuJean-Christophe PLAGNIOL-VILLARD2009-03-221-15/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move common serial initialisation to cpuJean-Christophe PLAGNIOL-VILLARD2009-03-221-28/+2
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* AT91: Use AT91_CPU_CLOCK in displaysStelian Pop2008-11-211-1/+1
| | | | | | | | | | Introduce AT91_CPU_CLOCK and use it for displaying the CPU speed in the LCD driver. Also make AT91_MAIN_CLOCK and AT91_MASTER_CLOCK reflect the corresponding board clocks. Signed-off-by: Stelian Pop <stelian@popies.net>
* AT91: Replace (undefined) AT91_ID_US* by the board specific values.Stelian Pop2008-11-071-3/+3
| | | | | | | | | | | | AT91_ID_US0 / AT91_ID_US1 / AT91_ID_US2 were used but never defined. Since they are never used outside the board specific files, they can be replaced by the board specific AT91xxx_ID_US0 / AT91xxx_ID_US1 / AT91xxx_ID_US2. Bug spotted by Jesus Alvarez <jalvarez@micromint.com>. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* lcd: Let the board code show board-specific infoHaavard Skinnemoen2008-10-271-0/+29
| | | | | | | | | | | | | The information displayed when CONFIG_LCD_INFO is set is inherently board-specific, so it should be done by the board code. The current code dealing with this only handles two cases, and is already a horrible mess of #ifdeffery. Yes, this duplicates some code, but it also allows boards to print more board-specific information; this used to be very difficult. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
* rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD2008-10-183-7/+7
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91: Update board NAND drivers to current API.Scott Wood2008-08-131-19/+18
| | | | Signed-off-by: Scott Wood <scottwood@freescale.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-at91Wolfgang Denk2008-07-071-6/+6
|\
| * [AT91SAM9] Fix NAND FLASH timingsPatrice Vilchez2008-07-051-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | Fix NAND FLASH timings for at91sam9x evaluation kits. New timings are based on application note "NAND Flash Support on AT91SAM9 Microcontrollers" available at http://atmel.com/dyn/resources/prod_documents/doc6255.pdf Signed-off-by: Patrice Vilchez <patice.vilchez@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Stelian Pop <stelian@popies.net>
* | Cleanup out-or-tree building for some boards (.depend)Wolfgang Denk2008-07-021-1/+1
|/ | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* AT91SAM9261EK: hook up the ATMEL LCD driverStelian Pop2008-05-101-0/+64
| | | | | | | | | This patch makes the necessary adaptations (PIO configurations and defines in config header file) to hook up the Atmel LCD driver to the AT91SAM9261EK board. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* AT91SAM9261EK supportStelian Pop2008-05-106-0/+449
This patch adds support for the AT91SAM9261 chip and the AT91SAM9261EK board. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
OpenPOWER on IntegriCloud