summaryrefslogtreecommitdiffstats
path: root/board/amcc/kilauea
Commit message (Collapse)AuthorAgeFilesLines
* ppc4xx: Add 405EX(r) revision C PVR definitions and detection codeStefan Roese2008-05-131-7/+12
| | | | Signed-off-by: Stefan Roese <sr@denx.de>
* Remove all the search paths from the .lds files.Jason Wessel2008-04-172-2/+0
| | | | | | | The cross compiler is responsible for providing the correct libraries and the logic to find the linking libraries. Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* ppc4xx: Fix comment in 405EX DDR2 init codeStefan Roese2008-03-151-2/+2
| | | | Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Fix remaining CONFIG_COMMANDS in 4xx filesStefan Roese2008-01-171-1/+1
| | | | Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Update Kilauea CPLD configuration with USB PHY reset bitStefan Roese2008-01-141-7/+7
| | | | | | | | | Now that bit 29 is the USB PHY reset bit, update the Kilauea port to remove the USB PHY reset after powerup. The CPLD will keep the USB PHY in reset (active low) until the bit is set to 1 in board_early_init_f(). Signed-off-by: Stefan Roese <sr@denx.de>
* Fix linker scripts: add NOLOAD atribute to .bss/.sbss sectionsWolfgang Denk2008-01-122-2/+2
| | | | | | | | | | | | | | | | | | | With recent toolchain versions, some boards would not build because or errors like this one (here for ocotea board when building with ELDK 4.2 beta): ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab] For many boards, the .bss section is big enough that it wraps around at the end of the address space (0xFFFFFFFF), so the problem will not be visible unless you use a 64 bit tool chain for development. On some boards however, changes to the code size (due to different optimizations) we bail out with section overlaps like above. The fix is to add the NOLOAD attribute to the .bss and .sbss sections, telling the linker that .bss does not consume any space in the image. Signed-off-by: Wolfgang Denk <wd@denx.de>
* ppc4xx: Bring 4xx fdt support up-to-dateStefan Roese2007-12-131-0/+1
| | | | | | | | This patch update the 4xx fdt support. It enabled fdt booting on the AMCC Kilauea and Sequoia for now. More can follow later quite easily. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: 405EX: Correctly enable USB pinsStefan Roese2007-12-081-0/+7
| | | | | | | | This patch selects the USB data pins in the 405EX GPIO and MFC (multi function control) registers. This is done for the AMCC Kilauea and Makalu eval boards. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Kilauea: Add PCIe reset assertion upon power-upStefan Roese2007-11-301-9/+6
| | | | | | | | This manual PCIe reset triggering solves the problem seen with the Intel EPRO/1000 card, which was not detected (link not established) upon power-up reset. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Small AMCC Kilauea cleanupStefan Roese2007-11-151-39/+0
| | | | | | Remove not needed pci_target_init() function. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Make output a little shorter on PCIe detectionStefan Roese2007-11-051-6/+4
| | | | | | Now not max 3 lines but 2 lines are printed per PCIe port. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Add AMCC Kilauea/Haleakala NAND booting supportStefan Roese2007-11-033-1/+148
| | | | | | | This patch adds NAND booting support for the AMCC 405EX(r) eval boards. Again, only one image supports both targets. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Add initial AMCC Haleakala PPC405EXr eval board supportStefan Roese2007-10-311-3/+33
| | | | | | | | | | The Haleakala is nearly identical with the Kilauea eval board. The only difference is that the 405EXr only supports one EMAC and one PCIe interface. This patch adds support for the Haleakala board by using the identical image for Kilauea and Haleakala. The distinction is done by comparing the PVR. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Fix size setup in Kilauea DDR2 init routineStefan Roese2007-10-311-26/+26
| | | | | | | | | The size was initilized wrong. Instead of 256MB, the DDR2 controller was setup to 512MB. Now the correct values is used. This patch also does a little cleanup and adds a comment here. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Dynamic configuration of 4xx PCIe mode as root or endpoint modeStefan Roese2007-10-311-34/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for dynamic configuration of PCIe ports for the AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe boards Yucca & Katmai and the 405EX board Kilauea. This dynamic configuration is done via the "pcie_mode" environement variable. This variable can be set to "EP" or "RP" for endpoint or rootpoint mode. Multiple values can be joined via the ":" delimiter. Here an example: pcie_mode=RP:EP:EP This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2 as endpoint. Per default Yucca will be configured as: pcie_mode=RP:EP:EP Per default Katmai will be configured as: pcie_mode=RP:RP:REP Per default Kilauea will be configured as: pcie_mode=RP:RP Signed-off-by: Tirumala R Marri <tmarri@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Enable device tree support (fdt) on Kilauea per defaultStefan Roese2007-10-311-0/+14
| | | | | | | | | | | | | This patch enables the fdt support on the AMCC Kilauea eval board. Additionally now EBC ranges fdt fixup is included to support NOR FLASH mapping via the Linux physmap_of driver. This Kilauea port now support booting arch/ppc and arch/powerpc Linux kernels. The default environment "net_nfs" is for arch/ppc and "net_nfs_fdt" is for arch/powerpc. In the long run, arch/ppc support will be removed. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Add initial AMCC Kilauea 405EX supportStefan Roese2007-10-317-0/+1125
Signed-off-by: Stefan Roese <sr@denx.de>
OpenPOWER on IntegriCloud