summaryrefslogtreecommitdiffstats
path: root/arch/powerpc
Commit message (Collapse)AuthorAgeFilesLines
* powerpc/85xx: Add C29x SoC supportMingkai Hu2013-08-097-0/+109
| | | | | | | | | | | | | | | The Freescale C29x family is a high performance crypto co-processor. It combines a single e500v2 core with necessary SEC engine. There're three SoC types(C291, C292, C293) with the following features: - 512K L2 Cache/SRAM and 512 KB platform SRAM - DDR3/DDR3L 32bit DDR controller - One PCI express (x1, x2, x4) Gen 2.0 Controller - Trust Architecture 2.0 - SEC6.0 engine Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Po Liu <Po.Liu@freescale.com>
* powerpc/pcie: remove PCIe version 3.x define for B4860 and B4420Zang Roy-R619112013-08-091-1/+0
| | | | | | B4860 and B4420 has PCIe version 2.4 IP instead of 3.x Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
* powerpc/pcie: add PCIe version 3.x supportZang Roy-R619112013-08-092-2/+34
| | | | | | | | | | | | | | | | | | | | | | | | | T4240 PCIe IP is version 3.0 and has some update comparing previous QorIQ products. 1. Move Freescale specific register define to arch/powerpc/include/asm/fsl_pci.h and update the register offset define for T4240. 2. add the status/control register define use status/control register to judge the link status 3. The original code uses 'Programming Interface' field to judge if PCIE is EP or RC mode, however, T4240 does not support this functionality. According to PCIE specification, 'Header Type' offset 0x0e is used to indicate header type, so for PCIE controller, the patch changes code to use 'Header Type' field to identify if the PCIE is RC or EP mode. This patch fixes the PCIe card link up issue on T4240QDS. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/rman: fix RMan support for t4240 and b4860Minghuan Lian2013-08-092-8/+8
| | | | | | | | | | | | 1. Add CONFIG_SYS_DPAA_RMAN macro to t4240 and b4860. 2. Decrease RMan liodn offset number. SET_RMAN_LIODN() is used to set liodn offset of RMan blocks 0-3. For t4240 and b4860, RMan liodn base is assigned to 922, the original offset number is too large that the liodn (base+offset 922+678 = 1600) is greater than 0x500 the maximum liodn number. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/asm: Move function declaration of 'serdes_get_prtcl' to fsl_serdes.hShaveta Leekha2013-08-092-1/+1
| | | | | | | It allows files not in the same path to use this function as required by B4 board file Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
* powerpc/mpc85xx: Add defines for serdes RSTCTL registerShaveta Leekha2013-08-091-1/+3
| | | | | | | | Also change the define name SRDS_RSTCTL_SDPD to SRDS_RSTCTL_SDEN, which stands for SerDes enable as mentioned in SerDes module guide Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
* board/bsc9132qds: Configure DSP DDR controllerPriyanka Jain2013-08-091-0/+6
| | | | | | | | | | | | | | BSC9132 SoC has two separate DDR controllers for PowerPC side and DSP side DDR. They are mapped to PowerPC and DSP CCSR space respectively. BSC9132QDS has two on-board MC34716EP DDR3 memory one connected to PowerPC and other to DSP side controller. Configure DSP DDR controller similar to PowerPC side DDR controller as memories are exactly similar. Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* board/bsc9132qds: Add DSP side tlb and lawsPriyanka Jain2013-08-092-1/+9
| | | | | | | | | | | | | | | BSC9132QDS is a Freescale Reference Design Board for BSC9132 SoC which is a integrated device that contains two powerpc e500v2 cores and two DSP starcores. To support DSP starcore -Creating LAW and TLB for DSP-CCSR space. -Creating LAW for DSP-core subsystem M2 and M3 memory -Creating LAW for 1GB DDR which is connected exclusively to DSP-cores Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc/srio-pcie-boot: Avoid the NOR_BOOT macro when boot from SRIO/PCIELiu Gang2013-08-091-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | When a board (slave) boots from SRIO/PCIE, it would get the instructions from a remote board (master) by SRIO/PCIE interface, and the slave's u-boot image should be built with the SYS_TEXT_BASE=0xFFF80000; So the u-boot of the slave should avoid the NOR_BOOT branch at the booting stage. For example, when a P2041RDB boots from SRIO/PCIE, it will set TLB entry 15 from base address "CONFIG_SYS_MONITOR_BASE & 0xffc00000", and with the 4M size as the boot window in NOR_BOOT branch. Because the CONFIG_SYS_MONITOR_BASE = CONFIG_SYS_TEXT_BASE = 0xFFF80000, so the TLB entry will be from base address 0xffc00000 and with 4M size. Then the u-boot will set TLB entry 14 from base address "CONFIG_SYS_INIT_RAM_ADDR", and with the 16K size as the initial stack window. For the P2041RDB platform, the CONFIG_SYS_INIT_RAM_ADDR = 0xffd00000. So the TLB entry 14 and 15 will be in confliction. There will be right TLB entries configurations when avoid the NOR_BOOT branch and set the boot window from 0xfff00000 with 1M size space. Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
* powerpc/mpc85xx: Workaround for A-005812York Sun2013-08-094-0/+29
| | | | | | | | Erratum A-005812 Incorrect reservation clearing in Write Shadow mode can result in invalid atomic operations. For u-boot, this erratum only impacts SoCs running in write shadow mode. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/mpc8xxx: Add memory reset controlYork Sun2013-08-097-13/+102
| | | | | | | | | JEDEC spec requires the clocks to be stable before deasserting reset signal for RDIMMs. Clocks start when any chip select is enabled and clock control register is set. This patch also adds the interface to toggle memory reset signal if needed by the boards. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/mpc8xxx: Add x4 DDR device supportYork Sun2013-08-096-0/+13
| | | | | | | | | On selected platforms, x4 DDR devices can be supported. Using x4 devices may lower the performance, but generally they are available for higher density. Tested on MT36JSF2G72PZ-1G9E1 RDIMM. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/mpc8xxx: Set inactive csn_bnds to 0xffffffffYork Sun2013-08-092-3/+9
| | | | | | | | | | | | When chip select interleaving is enabled, cs0_bnds is used for address binding. Other csn_bnds are not used. When two controllers interleaving is enabled, cs0_bnds of both controllers are used, other csn_bnds are not. However, the unused csn_bnds may be used internally for calculating addresses for calibration. Setting those registers to 0 may confuse controllers in some cases. Instead, setting them to 0xffffffff together with normal LAWs will guarantee the address is not mapped to DDR. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/corenet: Move RCW print to cpu.cYork Sun2013-08-091-4/+19
| | | | | | | The RCW print is common for all corenet platforms. Not necessary to ducplicate in each board file. Signed-off-by: York Sun <yorksun@freescale.com>
* mpc85xx: Base emulator supportYork Sun2013-08-094-1/+19
| | | | | | | | | Prepare for emulator support for mpc85xx parts. Disable DDR training and skip wrlvl_cntl_2 and wrlvl_cntl_3 registers. These two registers improve stability but not supported by emulator. Add CONFIG_FSL_TBCLK_EXTRA_DIV for possible adjustment to time base. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/corenet: Move CONFIG_FSL_CORENET out of board header fileYork Sun2013-08-091-0/+5
| | | | | | | Move CONFIG_FSL_CORENET define to config_mpc85xx.h. It is not board specific feature and belongs to SoC header. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/t4: Correct LIODN assignment for SRIOLiu Gang2013-08-092-2/+3
| | | | | | | For T4 platform, the SRIO LIODN registers are in SRIO address space and not in GUTs. Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
* powerpc/b4860: Correct LIODN assignment for SRIOLiu Gang2013-08-092-2/+3
| | | | | | | For B4, the SRIO LIODN registers are in SRIO address space and not in GUTs. Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
* powerpc/srio: Update the SRIO LIODN registers and ID table macroLiu Gang2013-08-092-0/+23
| | | | | | | | | | | | For some PowerPC platforms, LIODN registers for SRIO ports are in SRIO register address space. So the ccsr_rio structure should be updated for those LIODN registers. In addition, add a new macro "SET_SRIO_LIODN_BASE" to create the SRIO LIODN ID table based on the SRIO LIODN register address. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini2013-07-249-51/+16
|\ | | | | | | | | | | | | | | | | | | | | The sandburst-specific i2c drivers have been deleted, conflict was just over the SPDX conversion. Conflicts: board/sandburst/common/ppc440gx_i2c.c board/sandburst/common/ppc440gx_i2c.h Signed-off-by: Tom Rini <trini@ti.com>
| * i2c, ppc4xx_i2c: switch to new multibus/multiadapter supportDirk Eibach2013-07-236-33/+5
| | | | | | | | | | | | | | Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Heiko Schocher <hs@denx.de> Cc: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
| * i2c, multibus: get rid of CONFIG_I2C_MUXHeiko Schocher2013-07-231-14/+0
| | | | | | | | | | | | | | | | | | | | | | CONFIG_I2C_MUX is replaced through the new i2c multibus/multiadapter framework, configured through CONFIG_SYS_I2C. As CONFIG_I2C_MUX is only used on the keymile boards, and they are now completely moved to the new framework, remove CONFIG_I2C_MUX. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Holger Brunck <holger.brunck@keymile.com> Tested-By: Holger Brunck <holger.brunck@keymile.com>
| * i2c, soft-i2c: switch to new multibus/multiadapter supportHeiko Schocher2013-07-231-6/+3
| | | | | | | | | | | | | | | | | | - added to soft_i2c driver new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@wwwdotorg.org>
| * i2c: common changes for multibus/multiadapter supportHeiko Schocher2013-07-232-3/+13
| | | | | | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Simon Glass <sjg@chromium.org> Cc: Henrik Nordström <henrik@henriknordstrom.net>
* | Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24316-4981/+317
|/ | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* powerpc/mpc85xx:Disable Debug TLB entry for non-minimal SPLPrabhakar Kushwaha2013-07-161-1/+3
| | | | | | | | | | CONFIG_SPL_BUILD creates debug TLB entry, so disable it before init_tlbs. CONFIG_SPL_INIT_MINIMAL never creates any debug TLB entry, so no need of disable_tlb(). Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Build arch/$ARCH/lib/bootm.o depending on CONFIG_CMD_BOOTMDirk Eibach2013-07-161-1/+1
| | | | | | | | MAKEALL is fine for ppc4xx and mpc85xx. Run checks were done on our controlcenterd hardware. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Fix bootm to work on powerpc again (compressed uImage)Stefan Roese2013-06-281-5/+0
| | | | | | | | | | | | | | Patch 35fc84fa1 [Refactor the bootm command to reduce code duplication] breaks booting Linux (compressed uImage with fdt) on powerpc. boot_jump_linux() mustn't be called before boot_prep_linux() and boot_body_linux() have been called. So remove the superfluous call to boot_jump_linux() in arch/powerpc/lib/bootm.c as its called later on in this function. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@ti.com>
* powerpc/85xx: Add P1023RDB board supportChunhe Lan2013-06-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | P1023RDB Specification: ----------------------- Memory subsystem: 512MB DDR3 (Fixed DDR on board) 64MB NOR flash 128MB NAND flash Ethernet: eTSEC1: Connected to Atheros AR8035 GETH PHY eTSEC2: Connected to Atheros AR8035 GETH PHY PCIe: Three mini-PCIe slots USB: Two USB2.0 Type A ports I2C: AT24C08 8K Board EEPROM (8 bit address) Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx:Disable Debug TLB entry before init_tlbsPrabhakar Kushwaha2013-06-201-0/+4
| | | | | | | | | init_tlbs() initialize all the TLB entries required for the system. So disable DEBUG TLB entry before TLB entries initialization. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc: mpc85xx/mpc86xx: Fix off-by-one boundary checking with ARRAY_SIZEAxel Lin2013-06-2019-25/+25
| | | | | | | | If a variable is used as array subscript, it's valid value range is 0 ... ARRAY_SIZE -1. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: modify the functionality clear_bss and aligning the end ↵Ying Zhang2013-06-202-1/+3
| | | | | | | | | | | | | | | | | | | | address of the BSS There will clear the BSS in the function clear_bss(), the reset address of the BSS started from the __bss_start, and increased by four-byte increments, finally stoped depending on the address is equal to the _bss_end. If the end address __bss_end is not alignment to 4byte, it will be an infinite loop. 1. The reset action stoped depending on the reset address is greater than or equal the end address of the BSS. 2. The end address of the BSS should be 4byte aligned. Because the reset unit is 4 Bytes. This patch is on top of the patch "powerpc/mpc85xx: support application without resetvec segment in the linker script". Signed-off-by: Ying Zhang <b40530@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: support application without resetvec segment in the linker ↵Ying Zhang2013-06-202-0/+22
| | | | | | | | | | | | | | | | script For SD/SPI 2-stage bootloader, the On-Chip Rom code loads the SPL into L2 SRAM, then jump to it to begin execution. After that, the SPL loads the final uboot image into DDR, then jump to it to begin execution. The segment .resetvec in the SPL and in final U-boot is useless. So, add new symbols CONFIG_SYS_MPC85XX_NO_RESETVEC for this application. If CONFIG_SYS_MPC85XX_NO_RESETVEC is set, the segment .resetvec is excluded and the segment .bootpg is placed in the previous 4K of the segment .text. Signed-off-by: Ying Zhang <b40530@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: work around erratum A-006593Scott Wood2013-06-203-0/+8
| | | | | | | | | | | | Erratum A-006593 is "Atomic store may report failure but still allow the store data to be visible". The workaround is: "Set CoreNet Platform Cache register CPCHDBCR0 bit 21 to 1'b1. This may have a small impact on synthetic write bandwidth benchmarks but should have a negligible impact on real code." Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* fsl_ifc: add support for different IFC bank countMingkai Hu2013-06-203-32/+125
| | | | | | | | | | | | Calculate reserved fields according to IFC bank count 1. Move csor_ext register behind csor register and fix res offset 2. Move ifc bank count to config_mpc85xx.h to support 8 bank count 3. Guard fsl_ifc.h with CONFIG_FSL_IFC macro to eliminate the compile error on some devices that does not have IFC controller. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4qds: Slave module for boot from SRIO and PCIELiu Gang2013-06-201-0/+1
| | | | | | | | | | | | | | | | | | | | | When a T4 board boots from SRIO or PCIE, it needs to finish these processes: 1. Set all the cores in holdoff status. 2. Set the boot location to one PCIE or SRIO interface by RCW. 3. Set a specific TLB entry for the boot process. 4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot. 5. Set a specific TLB entry in order to fetch ucode and ENV from master. 6. Set a LAW entry with the TargetID one of the PCIE ports for ucode and ENV. 7. Slave's u-boot image should be generated specifically by make xxxx_SRIO_PCIE_BOOT_config. This will set SYS_TEXT_BASE=0xFFF80000 and other configurations. For more information about the feature of Boot from SRIO/PCIE, please refer to the document doc/README.srio-pcie-boot-corenet. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/b4860qds: Slave module for boot from SRIO and PCIELiu Gang2013-06-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | When a b4860qds board boots from SRIO or PCIE, it needs to finish these processes: 1. Set all the cores in holdoff status. 2. Set the boot location to one PCIE or SRIO interface by RCW. 3. Set a specific TLB entry for the boot process. 4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot. 5. Set a specific TLB entry in order to fetch ucode and ENV from master. 6. Set a LAW entry with the TargetID one of the PCIE ports for ucode and ENV. 7. Slave's u-boot image should be generated specifically by make xxxx_SRIO_PCIE_BOOT_config. This will set SYS_TEXT_BASE=0xFFF80000 and other configurations. For more information about the feature of Boot from SRIO/PCIE, please refer to the document doc/README.srio-pcie-boot-corenet. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/boot: Change the macro of Boot from SRIO and PCIE master moduleLiu Gang2013-06-203-7/+3
| | | | | | | | | | | | | | | | | Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable the master module of Boot from SRIO and PCIE on a platform. But this is not a silicon feature, it's just a specific booting mode based on the SRIO and PCIE interfaces. So it's inappropriate to put the macro into the file arch/powerpc/include/asm/config_mpc85xx.h. Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to "CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros in configuration header file of each board which can support the master module of Boot from SRIO and PCIE. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* 85xx: Change case of MPC85XX_PORBMSR_ROMLOC_SHIFTAndy Fleming2013-06-201-1/+1
| | | | | | | All the other constants use lowercase 'x' in "MPC85xx", so we duplicate that here. Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc: Use lower case for the core namesFabio Estevam2013-06-202-5/+5
| | | | | | | | | | | | | | | | | | Freescale documentation presents the PowerPC core names in lower case, such as "e300", "e500", "e600", etc. Change the upper case occurrences into lower case so that the core names reported in U-boot can match the ones from the documentation. While at it also fix a checkpatch error: ERROR: space prohibited before that close parenthesis ')' #53: FILE: arch/powerpc/cpu/mpc86xx/cpu.c:81: + printf("e600 Core %d", (msscr0 & 0x20) ? 1 : 0 ); Reported-by: Heinz Wrobel <heinz.wrobel@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/BSC9132: Add IFC bank countYork Sun2013-06-201-0/+1
| | | | | | | BSC9132 has 3 IFC banks. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* board/bsc9131rdb: Add DSP side tlb and lawsPriyanka Jain2013-06-202-0/+7
| | | | | | | | | | | | | | | BSC9131RDB is a Freescale Reference Design Board for BSC9131 SoC which is a integrated device that contains one powerpc e500v2 core and one DSP starcore. To support DSP starcore -Creating LAW and TLB for DSP-CCSR space. -Creating LAW for DSP-core subsystem M2 memory Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: new SPL support for IFC NANDPrabhakar Kushwaha2013-06-201-1/+1
| | | | | | | | | | | | | | Linker script is not able find start.o binary. So add its absolute path in u-boot-spl.lds. This change is similar to u-boot-nand.lds common/Makefile: Avoid compiling unnecssary files fsl_ifc_spl.c : It is is responsible for reading u-boot binary from NAND flash and copying into DDR. It also transfer control from NAND SPL to u-boot image present in DDR. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx:No NOR boot, do not compile IFC errata A003399Prabhakar Kushwaha2013-06-202-4/+4
| | | | | | | | IFC errata A003399 is valid for IFC NOR boot i.e.if no on-board NOR flash or no NOR boot, do not compile its workaround. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: explicit cast the SDRAM size to type phys_size_tMingkai Hu2013-06-201-1/+1
| | | | | | | | | | To avoid sign extension problem, use explicit casting to cast the SDRAM size to type phys_size_t, or else, if the SDRAM size is 2G(0x80000000), it will be extended to 0xffffffff80000000 when phys_size_t is type 'unsigned long long'. Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* 85xx: Change clock-frequency compatible to 2.0Andy Fleming2013-06-201-1/+1
| | | | | | | | | Accidentally applied an earlier version of the patch, which set the compatible to "fsl,qoriq-clockgen-2", lacking the final ".0". Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
* powerpc: fix 8xx and 82xx type-punning warnings with GCC 4.7Scott Wood2013-06-118-21/+35
| | | | | | | | | | | C99's strict aliasing rules are insane to use in low-level code such as a bootloader, but as Wolfgang has rejected -fno-strict-aliasing in the past, add a union so that 16-bit accesses can be performed. Compile-tested only. Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-05-3049-6351/+755
|\ | | | | | | | | | | Conflicts: common/cmd_fpga.c drivers/usb/host/ohci-at91.c
| * powerpc/mpc85xx: Clear L1 D-cache lockYork Sun2013-05-241-0/+1
| | | | | | | | | | | | | | | | dcbi instruction has been used to clear D-cache lock. However, the cache lock is persistent for e6500 core. Use dcblc to clear the lock explicitly. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * SECURE BOOT - Removed deletion of TLB entries codeRuchika Gupta2013-05-242-17/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | Boot ROM code creates TLB entries for 3.5G space before entering the u-boot. Earlier we were deleting these entries after early initialization of CPU. In recent past, code has been added to invalidate all these entries before relocation of u-boot code. So this code to delete TLB entries after CPU initialization is no longer required. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Acked-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
OpenPOWER on IntegriCloud