summaryrefslogtreecommitdiffstats
path: root/arch/powerpc/include
Commit message (Collapse)AuthorAgeFilesLines
* mpc85xx/t104x: Enable L2 and CPC cache when resumeTang Yuantian2014-07-221-0/+6
| | | | | | | | | | | When resume from deep sleep, uboot needs to enable L2 and CPC cache, or they would be keeping unusable in kernel because kernel didn't enble or initialized them. This patch didn't change the existing L2 cache enabling code, just put them in a function. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t4240qds: fix offset of serdes when checking reference clockShaohui Xie2014-07-221-0/+6
| | | | | | | | T4240 has 4 serdes, each serdes has 4k memory space, two PLLs. We use PLL1CR0 to check the serdes reference clock. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* driver/ddr: Fix DDR4 driver for ARMYork Sun2014-07-221-0/+3
| | | | | | | Previously the driver was only tested on Power SoCs. Different barrier instructions are needed for ARM SoCs. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: Removed support for G4060Sandeep Singh2014-07-221-1/+0
| | | | | | | G4060 has no PA cores, hence removing its support. Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* qe: move immap_qe.h from arch directory into common directoryZhao Qiang2014-07-221-582/+0
| | | | | | | | ls1021 is arm-core and supports qe too. Move immap_qe.h into common directory for both arm and powerpc. Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: Add workaround to enable TDM on T1040Sandeep Singh2014-06-053-1/+8
| | | | | | | | | | | | | | | This is a workaround for 32 bit hardware limitation of TDM. T1040 has 36 bit physical addressing, TDM DMAC register are 32 bit wide but need to store address of CCSR space which lies beyond 32 bit address range. This workaround creats a LAW to enable access of TDM DMA to CCSR by mapping CCSR to overlap with DDR. A hole of 16M is created in memory using device tree. This workaround law is set only if "tdm" is defined in hwconfig. Also disable POST tests and add LIODN for TDM Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/serdes: Add the workaround for erratum A-007186Shaveta Leekha2014-06-052-2/+37
| | | | | | | | | | | | | | | | | | SerDes PLL is calibrated at reset. When the junction temperature delta from the time the PLL is calibrated exceeds +56C/-66C, jitter may increase and can cause PLL to unlock. This workaround overwrite the SerDes registers with new values, to calibrate SerDes registers. These values are known to work fine for all temperature ranges. This workaround is valid for B4, T4 and T2 platforms, so added in their config. Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com> [York Sun: replaced typedef ccsr_sfp_regs_t with struct ccsr_sfp_regs] Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: Add workaround for DDR erratum A004508York Sun2014-06-051-0/+18
| | | | | | | | | | | When the DDR controller is initialized below a junction temperature of 0°C and then operated above a junction temperature of 65°C, the DDR controller may cause receive data errors, resulting ECC errors and/or corrupted data. This erratum applies to the following SoCs and their variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023, P2020. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc: hiddendragon: remove orphan boardMasahiro Yamada2014-05-301-12/+0
| | | | | | | | | | | This board has been orphan for a while. (Emails to its maintainer have been bouncing.) Because MPC82xx family is old enough, nobody would pick up the maintainership on it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denx <wd@denx.de>
* mpc85xx/p1020:Define number of USB controllers used on P1020RDB-PD platformramneek mehresh2014-05-161-0/+2
| | | | | | | | P1020 SoC which has two USB controllers, but only first one is used on this platform. Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: Added B4460 supportShaveta Leekha2014-05-161-0/+1
| | | | | | | | | | | B4460 differs from B4860 only in number of CPU cores, hence used existing support for B4860. B4460 has 2 PPC cores whereas B4860 has 4 PPC cores. Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* fsl/pci: Add workaround for erratum A-005434Chunhe Lan2014-05-161-0/+1
| | | | | | | | | | By default, all PEX inbound windows PEX_PEXIWARn[TRGT] are mapped to 0xF, which is local memory. But for BSC9132, 0xF is CCSR, 0x0 is local memory. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/85xx: add T4080 SoC supportShengzhou Liu2014-05-134-7/+18
| | | | | | | | The T4080 SoC is a low-power version of the T4160. T4080 combines 4 dual-threaded Power Architecture e6500 cores with single cluster and two memory complexes. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
* powerpc/t208x: enable errata A006261, A006593, A006379Shengzhou Liu2014-05-132-0/+6
| | | | | | | Enable errata A006261, A006593, A006379 for T208x. Additionally enable CONFIG_CMD_ERRATA for T2080RDB. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- Add secure boot target for T2080RDBAneesh Bansal2014-05-131-0/+1
| | | | | | | | | | | Secure Boot Target is added for T2080RDB Changes: For Secure boot, CPC is configured as SRAM and used as house keeping area which needs to be disabled. So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T2080RDB. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- secure boot target for t1040rdbAneesh Bansal2014-05-131-1/+1
| | | | | | | | T1040RDB.h file is removed and a unified file T104xRDB.h is created. Hence macro CONFIG_T1040 is renamed to CONFIG_T104x. Signed-off-by: Gaurav Kumar Rana <gaurav.rana@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
* bd_info: remove bi_barudrate member from struct bd_infoMasahiro Yamada2014-05-121-1/+0
| | | | | | | | | | | | | | | | | gd->bd->bi_baudrate is a copy of gd->baudrate. Since baudrate is a common feature for all architectures, keep gd->baudrate only. It is true that bi_baudrate was passed to the kernel in that structure but it was a long time ago. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de> Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
* powerpc/85xx: Enhance get_sys_info() to check clocking modevijay rai2014-04-221-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1040 and it's variants provide "Single Oscillator Source" Reference Clock Mode. In this mode, single onboard oscillator(DIFF_SYSCLK) can provide the reference clock (100MHz) to the following PLLs: • Platform PLL • Core PLLs • USB PLL • DDR PLL, etc The cfg_eng_use0 of porsr1 register identifies whether the SYSCLK (single-ended) or DIFF_SYSCLK (differential) is selected as the clock input to the chip. get_sys_info has been enhanced to add the diff_sysclk so that the various drivers can be made aware of ths diff sysclk configuration and act accordingly. Other changes: -single_src to ddr_refclk_sel, as it is use for checking ddr reference clock -Removed the print of single_src from get_sys_info as this will be -printed whenever somebody calls get_sys_info which is not appropriate. -Add print of single_src in checkcpu as it is called only once during initialization Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx: Add support for the supplement configuration unit registerTang Yuantian2014-04-221-0/+22
| | | | | | | | | | | | The supplement configuration unit (SCFG) provides chip-specific configuration and status registers for the device. It is the chip defined module for extending the device configuration unit (DCFG) module. It provides a set of CCSR registers in addition to those available in the device configuration unit. The base address for this unit is 0x0F_C000. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: Add workaround for erratum A007212York Sun2014-04-222-0/+4
| | | | | | | | | | | | | | | | | Erratum A007212 for DDR is about a runaway condition for DDR PLL oscilliator. Please refer to erratum document for detail. For this workaround to work, DDR PLL needs to be disabled in RCW. However, u-boot needs to know the expected PLL ratio. We put the ratio in a reserved field RCW[18:23]. U-boot will skip this workaround if DDR PLL ratio is set, or the reserved field is not set. Workaround for erratum A007212 applies to selected versions of B4/T4 SoCs. It is safe to apply the workaround to all versions. It is helpful for upgrading SoC without changing u-boot. In case DDR PLL is disabled by RCW (part of the erratum workaround), we need this u-boot workround to bring up DDR clock. Signed-off-by: York Sun <yorksun@freescale.com>
* fsl/usb: Workaround for USB erratum-A007075Nikhil Badola2014-04-222-0/+19
| | | | | | | | | | | | Put a delay of 5 millisecond after reset so that ULPI phy gets enough time to come out of reset. Erratum A007075 applies to following SOCs and their variants, if any P1010 rev 1.0 B4860 rev 1.0, 2.0 P4080 rev 2.0, 3.0 Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Add DDR4 support to Freescale DDR driverYork Sun2014-04-221-3/+14
| | | | | | | Mostly reusing DDR3 driver, this patch adds DDR4 SPD handling, register calculation and programming. Signed-off-by: York Sun <yorksun@freescale.com>
* QE/U-QE: Add U-QE supportZhao Qiang2014-04-223-1/+11
| | | | | | | | | | | | | Modify code to adapt to both u-qe and qe. U_QE is a kind of cutted QE. the differences between U_QE and QE 1. UCC: U_QE supports 2 UCCs while QE supports up to 8 UCCs. 2. IMMR: have different immr base addr. 3. iopin: U_QE doesn't need to config iopin. Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- Add secure boot target for T1040QDS and T1040RDBAneesh Bansal2014-04-221-1/+3
| | | | | | | | | | | | | Secure Boot Target is added for T1040QDS and T1040RDB Changes: For Secure boot, CPC is configured as SRAM and used as house keeping area which needs to be disabled. So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T1040QDS and CONFIG_T1040RDB Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- Add secure boot target for T2080QDSAneesh Bansal2014-04-221-1/+3
| | | | | | | | | | | Secure Boot Target is added for T2080QDS Changes: For Secure boot, CPC is configured as SRAM and used as house keeping area which needs to be disabled. So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T2080QDS. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- Add secure boot target for T4240QDS and T4160QDSAneesh Bansal2014-04-221-1/+1
| | | | | | | | | | | Secure Boot Target is added for T4240QDS and T4160QDS Changes: For Secure boot, CPC is configured as SRAM and used as house keeping area which needs to be disabled. So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T4240QDS. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- Add secure boot target for B4860QDSAneesh Bansal2014-04-221-0/+6
| | | | | | | | | | | | | | | | | Changes: 1. L2 cache is being invalidated by Boot ROM code for e6500 core. So removing the invalidation from start.S 2. Clear the LAW and corresponding configuration for CPC. Boot ROM code uses it as hosekeeping area. 3. For Secure boot, CPC is configured as SRAM and used as house keeping area. This configuration is to be disabled once in uboot. Earlier this disabling of CPC as SRAM was happening in cpu_init_r. As a result cache invalidation function was getting skipped in case CPC is configured as SRAM.This was causing random crashes. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: SECURE BOOT- Add secure boot target for BSC9132QDSAneesh Bansal2014-04-221-0/+2
| | | | | | | | | | Add NOR, SPI and SD secure boot targets for BSC9132QDS. Changes: - Debug TLB entry is not required for Secure Boot Target. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* PPC 85xx: Add qemu-ppce500 machineAlexander Graf2014-04-221-0/+4
| | | | | | | | | | | | | | | | For KVM we have a special PV machine type called "ppce500". This machine is inspired by the MPC8544DS board, but implements a lot less features than that one. It also provides more PCI slots and is supposed to be enumerated by device tree only. This patch adds support for the generic ppce500 machine and tries to rely solely on device tree for device enumeration. Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* PPC: 85xx: Generalize DDR TLB mapping functionAlexander Graf2014-04-221-0/+8
| | | | | | | | | | The DDR mapping function really is just a generic virtual -> physical mapping function. Generalize it so it can support any virtual starting offset and IO maps just the same. Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc: remove MBX and MBX860T boards supportMasahiro Yamada2014-04-181-1/+0
| | | | | | | | | | | Enough time has passed since these boards were moved to Orphan. Remove. - Remove board/mbx8xx/* - Remove include/configs/{MBX.h,MBX860T.h} - Clean-up if defined(CONFIG_MBX) - Move the entries from boards.cfg to doc/README.scrapyard Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* powerpc: remove NX823 board supportMasahiro Yamada2014-04-181-3/+0
| | | | | | | | | | | Enough time has passed since this board was moved to Orphan. Remove. - Remove board/nx823/* - Remove include/configs/NX823.h - Clean-up ifdef(CONFIG_NX823) - Move the entry from boards.cfg to doc/README.scrapyard Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* mmc:eSDHC: Workaround for data timeout issue on Txxx SoCHaijun.Zhang2014-04-021-0/+5
| | | | | | | | | | | | | | 1. The Data timeout counter value in eSDHC_SYSCTL register is not working as it should be, so add quirks to enable this workaround to fix it to the max value 0xE. 2. Add CONFIG_SYS_FSL_ERRATUM_ESDHC111 to enable its workaround. * Update of patch for change mmc interface by Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2014-03-073-2/+74
|\
| * powerpc/mpc85xx: Add SCFG_PIXCLKCR register support for T1040Priyanka Jain2014-03-071-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1040 SoC has SCFG (Supplement Configuration) Block which provides chip specific configuration and status support. The base address of SCFG block in T1040 is 0xfc000. SCFG contains SCFG_PIXCLKCR (DIU pixel clock control register) at offset 0x28. Add definition of -SCFG block -SCFG_PIXCLKCR register -Bits definition of SCFG_PIXCLK register Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/usb: Workaround for erratum-A006261Suresh Gupta2014-03-072-0/+41
| | | | | | | | | | | | | | | | | | | | | | USB spec says that the minimum disconnect threshold should be over 525 mV. However, internal USB PHY threshold value is below this specified value. Due to this some devices disconnect at run-time. Hence, phy settings are tweaked to increased disconnect threshold to be above 525mV by using this workaround. Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/b4860: Add workaround for errata A006384 and A006475Shaveta Leekha2014-03-072-2/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384) and at cold temperatures(A006475), workaround recalibrate the PLLs with some SerDes configuration Both these errata are only applicable for b4 rev1. So, make workaround for these errata conditional, depending upon soc version. Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * B4860/B4420: Add PLL_NUM define for B4420/B4860 to use SerDes2 Refclks ↵Shaveta Leekha2014-03-071-0/+2
| | | | | | | | | | | | | | | | | | | | re-configuration B4860 has two PLL per SerDes whereas B4420 has one PLL per SerDes, add their defines in arch/powerpc/include/asm/config_mpc85xx.h Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * board/b4860qds: Add support to make PCIe SATA work on B4860QDSShaveta Leekha2014-03-071-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | 1) SerDes2 Refclks have been set properly to make PCIe SATA to work as it work on SerDes refclk of 100MHz 2) Mask the SerDes's device reset request before changing the Refclks for SerDes1 and SerDes2 for PLL locks to happen properly, device reset request bit unmasked after SerDes refclks configuration Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | powerpc: mpc8260: consolidate CONFIG_MPC8260 and CONFIG_8260Masahiro Yamada2014-03-073-3/+3
|/ | | | | | | | | | | | | | | | | | | | | | | Before this commit, CONFIG_MPC8260 and CONFIG_8260 were used mixed-up. All boards with mpc8260 cpu defined both of them: - CONFIG_MPC8260 was defined in board config headers and include/common.h - CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk We do not need to have both of them. This commit keeps only CONFIG_MPC8260. This commit does: - Delete CONFIG_8260 and CONFIG_MPC8260 definition in config headers and include/common.h - Rename CONFIG_8260 to CONFIG_MPC8260 in arch/powerpc/cpu/mpc8260/config.mk. - Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260 Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de>
* driver/ifc:Change accessor function to take care of endiannessPrabhakar Kushwaha2014-02-031-0/+3
| | | | | | | | | | | IFC registers can be of type Little Endian or big Endian depending upon Freescale SoC. Here SoC defines the register type of IFC IP. So update acessor functions with common IFC acessor functions to take care both type of endianness. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc/usb: Enable dual phy for T1040Nikhil Badola2014-02-031-2/+1
| | | | | | | | Define CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE macro for enabling dual phy in t1040 Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* boards/t1040qds: Adds ethernet support for T1040Prabhakar Kushwaha2014-02-031-0/+11
| | | | | | | | | | | | | | | | | Enable entherent for T1040QDS. It enables FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5 Define MDIO related configs Added eth.c file Update t1040.c to support RGMII and SGMII Update t1040qds.c to support ethernet Define the PHY address Signed-off-by: Arpit Goel <B44344@freescale.com> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> [York Sun: remove dash from commit message] Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: Update serdes protocols for T1040Prabhakar Kushwaha2014-02-031-7/+1
| | | | | | | | | | | | | T1040 has only one SerDes block. so update the code accordingly. Also, add support of SerDes Protocol 0x00, 0x06, 0x40, 0x69 0x85, 0xA7 and 0xAA Signed-off-by: Arpit Goel <B44344@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc: delete unused header filesMasahiro Yamada2014-01-243-1120/+0
| | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* eSDHC: Calculate envaddr accroding to the address formatHaijun.Zhang2014-01-221-0/+3
| | | | | | | | | | | | | | | | | On BSC9131, BSC9132, P1010 : For High Capacity SD Cards (> 2 GBytes), the 32-bit source address specifies the memory address in block address format. Block length is fixed to 512 bytes as per the SD High Capacity specification. So we need to convert the block address format to byte address format to calculate the envaddr. If there is no enough space for environment variables or envaddr is larger than 4GiB, we relocate the envaddr to 0x400. The address relocated is in the front of the first partition that is assigned for sdboot only. Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/85xx: update erratum a006379Shengzhou Liu2014-01-211-1/+5
| | | | | | | Enable Erratum A006379 for T2080, T2081, T4160, B4420. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t208x: fix macro CONFIG_SYS_FSL_NUM_USB_CTRLSShengzhou Liu2014-01-021-1/+1
| | | | | | | CONFIG_SYS_FSL_NUM_USB_CTRLS is no longer used, update it to new CONFIG_USB_MAX_CONTROLLER_COUNT. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
* powerpc/mpc85xx: Add support for single source clockingPriyanka Jain2014-01-022-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | Single-source clocking is new feature introduced in T1040. In this mode, a single differential clock is supplied to the DIFF_SYSCLK_P/N inputs to the processor, which in turn is used to supply clocks to the sysclock, ddrclock and usbclock. So, both ddrclock and syclock are driven by same differential sysclock in single-source clocking mode whereas in normal clocking mode, generally separate DDRCLK and SYSCLK pins provides reference clock for sysclock and ddrclock DDR_REFCLK_SEL rcw bit is used to determine DDR clock source -If DDR_REFCLK_SEL rcw bit is 0, then DDR PLLs are driven in normal clocking mode by DDR_Reference clock -If DDR_REFCLK_SEL rcw bit is 1, then DDR PLLs are driven in single source clocking mode by DIFF_SYSCLK Add code to determine ddrclock based on DDR_REFCLK_SEL rcw bit. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
* powerpc/mpc85xx: Update CONFIG_SYS_FSL_TBCLK_DIV for T1040Prabhakar Kushwaha2013-12-111-1/+1
| | | | | | | | | The default value of CONFIG_SYS_FSL_TBCLK_DIV is 16. So, update its value as default. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
OpenPOWER on IntegriCloud