| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
| |
The sama5d2 Xplained SPL supports the boot medias: spi flash
and SD Card.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
The DDR3-SDRAM initialization sequence is implemented in
accordance with the DDR3-SRAM/DDR3L-SDRAM initialization section
described in the SAMA5D2 datasheet.
Add registers and definitions of mpddrc controller, which is used
to support DDR3 devices.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
| |
|
|
|
|
|
|
|
|
| |
Add struct atmel_mpddrc_config to accommodate the mpddrc register
configurations, not using the mpddrc register map structure,
struct atmel_mpddrc, in order to increase readability and reduce
run-time memory use.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
To make saic redirect code sharing with other SoCs, move the
saic redirect code from SAMA5D4 particular file,
mach-at91/armv7/sama5d4_devices.c to a separate file,
mach-at91/atmel_sfr.c
Move ATMEL_SFR_AICREDIR_KEY definition to sama5d4.h, because each
SoC has its own value.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
| |
|
|
|
|
|
|
| |
To make matrix initialization code sharing with others,
use the matrix slave id macros, instead of hard-coding.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
The board supports following features:
- Boot media support: SD card/e.MMC/SPI flash,
- Support LCD display (optional, disabled by default),
- Support ethernet,
- Support USB mass storage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[fix checkpatch warnings]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
| |
|
|
|
|
|
| |
The PIO4 is introduced from SAMA5D2, as a new version
for Atmel PIO controller.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
The SDHCI is introduced by sama5d2, named as Secure Digital Multimedia
Card Controller(SDMMC). It supports the embedded MultiMedia Card (e.MMC)
Specification V4.41, the SD Memory Card Specification V3.0, and the SDIO
V3.0 specification. It is compliant with the SD Host Controller Standard
V3.0 specification.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Some peripherals may need a second clock source that may be different
from the system clock. This second clock is the generated clock (GCK)
and is managed by the PMC via PMC_PCR.
For simplicity, the clock source of the GCK is fixed to PLLA_CLK.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
| |
|
|
|
|
|
|
| |
Provide the specific addresses for the Chip ID and Chip ID Extension
registers, instead of the offset, which make it use on other chips.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
| |
|
|
|
|
|
|
| |
To enable the clocks on the at91 boards a constant (0x4) is used.
This is replaced with a define in at91_pmc.h (1 << 2).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
| |
|
|
|
|
|
|
|
| |
The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
| |
|
|
|
|
|
| |
Enable SPL support for at91sam9n12ek boards, now it supports
boot up from NAND flash, serial flash.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
|
| |
|
|
|
|
|
| |
Enable SPL support for at91sam9x5ek board. Now, it supports
boot up from NAND flash and SPI flash.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
|
| |
|
|
|
|
|
|
|
| |
The commit 8dfafdd (Introduce common timer functions), add common
timer functions, we can use them directly.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[rebase on current master]
Sigend-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
| |
|
|
|
|
| |
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[rebase on current master]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
|
Move arch/arm/include/asm/arch-at91/*
-> arch/arm/mach-at91/include/mach/*
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
