summaryrefslogtreecommitdiffstats
path: root/arch/arm/include/asm/arch-tegra
Commit message (Collapse)AuthorAgeFilesLines
...
* Tegra: Configure L2 cache control reg properly.Tom Warren2013-04-151-0/+1
| | | | | | | | | | Without this change, kernel fails at calling function cache_clean_flush during kernel early boot. Aprocryphally, intended for T114 only, so I check for a T114 SoC. Works (i.e. dalmore 3.8 kernel now starts printing to console). Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: support T33 SKU of Tegra30Stephen Warren2013-04-151-0/+1
| | | | | | | | | | | | | | | | | | | Make U-Boot aware of the T33 SKU of Tegra30, and treat it identically to any other Tegra30. An alternative would be to simply remove the SKU checking from tegra_get_chip_type(); most use of the value most likely simply wants to know the current chip, not the specific SKU. Or, the function could be split into separate tegra_get_chip() and tegra_get_sku() for the cases where differentiation really is required. I wonder whether tegra_get_chip_type() should printf() whenever any unkown chip/SKU is found, although perhaps the function is called so early that the printf() wouldn't actually make it to the UART anyway. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
* tegra: spi: rename tegra SPI driversAllen Martin2013-03-252-159/+0
| | | | | | | | | Rename tegra SPI drivers to tegra20_flash and tegra20_slink in preparation for commonization and addition of tegra114_spi. Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* tegra: remove support for UART SPI switchAllen Martin2013-03-251-2/+1
| | | | | | | | | | This feature was only used for tegra20 seaboard that had a pinmux conflict on the SPI pins. These boards were never manufactured, so remove this support to clean up SPI driver. Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra: MMC: Added/update SDMMC registers/base addresses for T20/T30Tom Warren2013-03-141-6/+29
| | | | | | | | Removed SDMMC base addresses from tegra.h since they're no longer used. Added additional vendor-specific SD/MMC registers and bus power defines. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra: MMC: Add DT support to MMC driver for all T20 boardsTom Warren2013-03-142-5/+10
| | | | | | | | | | | | tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc. Tested on Seaboard, fully functional. Tamonten boards (medcom-wide, plutux, and tec) use a different/new dtsi file w/common settings. Signed-off-by: Tom Warren <twarren@nvidia.com> Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra: I2C: Add T114 clock support to tegra_i2c driverTom Warren2013-03-141-0/+6
| | | | | | | | | | | | | T114 has a slightly different I2C clock, with a new (extra) divisor in standard/fast mode and HS mode. Tested on my Dalmore, and the I2C clock is 100KHz +/- 3Hz on my Saleae Logic analyzer. Added a new entry in compat_names for T114 I2C since it differs from the previous Tegra SoCs. A flag is set when T114 I2C HW is found so new features like the extra clock divisor can be used. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
* tegra: usb: move [start|stop]_port into ehci_hcd_[init|stop]Lucas Stach2013-03-141-19/+0
| | | | | | | | | | The ehci_hcd entry points were just calling into the Tegra USB functions. Now that they are in the same file we can just move over the implementation. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: usb: move implementation into right directoryLucas Stach2013-03-141-0/+268
| | | | | | | | | | | | | | | | This moves the Tegra USB implementation into the drivers/usb/host directory. Note that this merges the old /arch/arm/cpu/armv7/tegra20/usb.c file into ehci-tegra.c. No code changes, just moving stuff around. v2: While at it also move some defines and the usb.h header file to make usb driver usable for Tegra30. NOTE: A lot more work is required to properly init the PHYs and PLL_U on Tegra30, this is just to make porting easier and it does no harm here. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* Tegra114: Add arch-tegra114 include filesTom Warren2013-02-114-5/+62
| | | | | | | | | | Common Tegra files are in arch-tegra, shared between T20/T30/T114. Tegra114-specific headers are in arch-tegra114. Note that some of these will be filled in as more T114 support is added (drivers, WB/LP0 support, etc.). Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* tegra: add SPI SLINK driverAllen Martin2013-02-111-0/+84
| | | | | | | | | | | | | | | | | | | | | | Add driver for tegra SPI "SLINK" style driver. This controller is similar to the tegra20 SPI "SFLASH" controller. The difference is that the SLINK controller is a genernal purpose SPI controller and the SFLASH controller is special purpose and can only talk to FLASH devices. In addition there are potentially many instances of an SLINK controller on tegra and only a single instance of SFLASH. Tegra20 is currently ths only version of tegra that instantiates an SFLASH controller. This driver supports basic PIO mode of operation and is configurable (CONFIG_OF_CONTROL) to be driven off devicetree bindings. Up to 4 devices per controller may be attached, although typically only a single chip select line is exposed from tegra per controller so in reality this is usually limited to 1. To enable this driver, use CONFIG_TEGRA_SLINK Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: add addresses of SPI SLINK controllersAllen Martin2013-02-111-0/+6
| | | | | | | | Add I/O addresses of SPI SLINK controllers 1-6 Signed-off-by: Allen Martin <amartin@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* Tegra: Move common clock code to arch/arm/cpu/tegra-common/clock.cTom Warren2013-02-112-4/+57
| | | | | | | | | This 'commonizes' much of the clock/pll code. SoC-dependent code and tables are left in arch/cpu/tegraXXX-common/clock.c Some T30 tables needed whitespace fixes due to checkpatch complaints. Signed-off-by: Tom Warren <twarren@nvidia.com>
* Tegra: T20: Remove unused 'SLOW' SoC ID and PLLX table entryTom Warren2013-02-111-1/+0
| | | | Signed-off-by: Tom Warren <twarren@nvidia.com>
* Tegra30: Add common CPU (shared) filesTom Warren2013-01-161-46/+6
| | | | | | | | | These files are used by both SPL and main U-Boot. Also made minor changes to shared Tegra code to support T30 differences. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra30: Add arch-tegra30 include filesTom Warren2013-01-165-15/+231
| | | | | | | | | | | | Common Tegra files are in arch-tegra, shared between T20 and T30. Tegra30-specific headers are in arch-tegra30. Note that some of these will be filled in as more T30 support is added (drivers, WB/LP0 support, etc.). A couple of Tegra20 files were changed to support common headers in arch-tegra, also. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
* tegra: display: add board pinmuxMarc Dietrich2013-01-161-3/+4
| | | | | | | | Boards may require a different pinmux setup for DISPALY than the default one. Add a way to call into board specific code to set this up. Signed-off-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: nand: add board pinmuxLucas Stach2012-10-151-0/+1
| | | | | | | | Boards may require a different pinmux setup for NAND than the default one. Add a way to call into board specific code to set this up. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: clean up board include hellLucas Stach2012-10-151-1/+18
| | | | | | | | | | The prototypes used in board files were all scattered out, which lead to code duplication between SPL and normal U-Boot and some prototypes not actually being used. Consolidate this in a common board header. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra20: add clock_set_pllout functionLucas Stach2012-10-152-2/+21
| | | | | | | | | | | Common practice on Tegra 2 boards is to use the pllp_out4 FO to generate the ULPI reference clock. For this to work we have to override the default hardware generated output divider. This function adds a clean way to do so. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
* Tegra20: Move some include files to arch-tegra for sharing with Tegra30Tom Warren2012-10-1517-0/+1539
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h. Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20' 'root' file. All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK. Signed-off-by: Tom Warren <twarren@nvidia.com>
OpenPOWER on IntegriCloud