summaryrefslogtreecommitdiffstats
path: root/arch/arm/include/asm/arch-mx35
Commit message (Collapse)AuthorAgeFilesLines
* ehci-mxc: Add support for i.MX35Benoît Thébaudeau2012-11-161-0/+2
| | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
* MX35: add support for woodburn boardStefano Babic2012-10-261-0/+2
| | | | | | | | | | | | | | | | | | | | | The woodburn board is based on the MX35 SOC. Support for both external (NOR) and internal (SD Card) boot mode are added. It uses the generic SPL framework to implement the internal boot mode. The following peripherals are supported: - Ethernet (FEC) - SD Card - NAND (512 MB) - NOR Flash In the internal boot mode, a simple imximage header is generated to set the address in internal RAM where the SOC must copy the SPL code. The initial setup is then demanded to the SPL itself. Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX35: Add soc_boot_mode and soc_boot_device to MX35Stefano Babic2012-10-262-0/+69
| | | | | | | The functions are required to use the generic SPL Framework. Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX35: add LOW_LEVEL_SRAM_STACK to use SPL_FRAMEWORKStefano Babic2012-10-261-0/+2
| | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
* mx35: Fix eSDHC clocksBenoît Thébaudeau2012-10-161-1/+3
| | | | | | | | | | | | | | Each eSDHC instance has a dedicated clock. gd->sdhc_clk must also be set accordingly. This is good for the case only a single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix the multi-instance use case (initialization made directly with fsl_esdhc_initialize()). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Bénard <eric@eukrea.com> Cc: Otavio Salvador <otavio@ossystems.com.br>
* mx35: Clean up lowlevel_initBenoît Thébaudeau2012-10-161-96/+95
| | | | | | | | | | | | Clean up mx35 lowlevel_init: - Indent with tabs. - Fix comments. - Use defined values instead of literal constants. - Use defined macros instead of duplicating code. - Use macro parameters with default values instead of #define'd configs. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
* mx35: Define MAX and AIPS registersBenoît Thébaudeau2012-10-151-0/+52
| | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: Use MXC_I2C_CLK in imx i2c driverMatthias Weisser2012-10-151-0/+1
| | | | | | | | i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using MXC_I2C_CLK on all imx systems using i2c. Signed-off-by: Matthias Weisser <weisserm@arcor.de> Acked-by: Stefano Babic <sbabic@denx.de>
* mx35: Define default SoC input clock frequenciesBenoît Thébaudeau2012-09-061-0/+14
| | | | | | | | | Define default SoC input clock frequencies for i.MX35 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* mx35: Fix clock dividersBenoît Thébaudeau2012-09-061-29/+13
| | | | | | | | | The clock dividers that were used do not match at all the reference manual. They were either completely broken, or came from an early silicon revision incompatible with the current one. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
* mx35: Add definitions for clock gate valuesBenoît Thébaudeau2012-09-061-0/+6
| | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
* mxc: Define architecture identifierBenoît Thébaudeau2012-09-011-0/+2
| | | | | | | | | | | | | Define ARCH_MXC for i.MX devices. This is useful to identify features or behaviors common to all i.MX SoCs. The i.MX28 is omitted because its architecture is a bit different (like imx/mxc vs. mxs in Linux). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Andy Fleming <afleming@gmail.com> Cc: Kim Phillips <kim.phillips@freescale.com>
* mx35: Remove declaration of non-existing functionBenoît Thébaudeau2012-09-011-2/+0
| | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* mx35: Move clock enums to clock.hBenoît Thébaudeau2012-09-012-27/+27
| | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* mx35: Remove declaration of non-existing functionBenoît Thébaudeau2012-09-011-1/+0
| | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* mx35: Fix broken pin definitionsBenoît Thébaudeau2012-09-011-3/+0
| | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* MX: Set a common gpio.h for all i.MXStefano Babic2012-09-011-11/+1
| | | | | | | | | Each i.MX has its own gpio.h, defining the same structure. The internal GPIO controller has the same layout (at least for the register used by u-boot) and can be shared. Signed-off-by: Stefano Babic <sbabic@denx.de> Tested-by: Matt Sealey <matt@genesi-usa.com>
* mx35: Remove duplicate GPIO3_BASE_ADDRBenoît Thébaudeau2012-09-011-1/+0
| | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* mx3: Fix typo on IPU_CONF_CSI_ENBenoît Thébaudeau2012-09-011-1/+1
| | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* mx35: Fix typo on EDIOBenoît Thébaudeau2012-09-011-2/+2
| | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* mxc_i2c: specify i2c base address in config fileTroy Kisky2012-07-111-1/+1
| | | | | | | | | The following platforms had their config files changed flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd and mx53loco. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
* imx: Remove unneeded/repititive definitions from imx headersVikram Narayanan2012-04-161-2/+0
| | | | | | | Remove gpio related unused/repititive definitions from imx headers. Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
* mxc_spi: move machine specifics into CPU headersEric Nelson2012-02-271-0/+25
| | | | | | | | | | | | | | Move (E)CSPI register declarations into the imx-regs.h files for each supported CPU Introduce two new macros to control conditional setup MXC_CSPI - Used for processors with the Configurable Serial Peripheral Interface (MX3x) MXC_ECSPI - For processors with Enhanced Configurable... (MX5x, MX6x) Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org> Tested-by: Jason Liu <jason.hui@linaro.org>
* MX: serial_mxc: cleanup removing nasty #ifdefStefano Babic2011-12-061-3/+3
| | | | | | | | | | | | | | | | | | The serial driver for iMX SOCs is continuosly changed if a new SOC or not yet used port is used. CONFIG_SYS_<SOC>_<UART Port> defines were used only to find the base address for the selected UART. Instead of that, move the base address to the board configuration file and drop all #ifdef from driver. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Marek Vasut <marek.vasut@gmail.com> CC: Wolfgang Denk <wd@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> CC: Helmut Raiger <helmut.raiger@hale.at> CC: John Rigby <jcrigby@gmail.com> CC: Matthias Weisser <weisserm@arcor.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
* MX35: Drop unnecessary prototypes from imx-regs.hStefano Babic2011-11-031-4/+0
| | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX35: factorize common assembly codeStefano Babic2011-11-031-0/+140
| | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX35: add pins definition for UART3Stefano Babic2011-11-031-0/+3
| | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX35: added ESDC structure to imx-regsStefano Babic2011-11-031-0/+30
| | | | | | | | The structure and PLL defines are added to the imx-regs.h file and dropped from board header files. Signed-off-by: Stefano Babic <sbabic@denx.de>
* FEC: Move imx_get_mac_from_fuse() definition to fec_mxc.hMarek Vasut2011-09-301-2/+0
| | | | | | | | Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
* MX35: make use of GPIO framework for MX35 processorStefano Babic2011-09-041-0/+40
| | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
* SPI: mxc_spi: replace fixed offsets with structuresStefano Babic2011-02-021-0/+12
| | | | | | | | This patch cleans driver code replacing all accesses to registers with fixed offsets with a corresponding structure. Signed-off-by: Stefano Babic <sbabic@denx.de>
* Add support for MX35 processorStefano Babic2011-02-026-0/+1287
The patch adds basic support for the Freescale's i.MX35 (arm1136 based) processor. The patch adds also a prototype for the initialization of the FEC(ethernet controller) to netdev.h to avoid warnings. Signed-off-by: Stefano Babic <sbabic@denx.de>
OpenPOWER on IntegriCloud