summaryrefslogtreecommitdiffstats
Commit message (Expand)AuthorAgeFilesLines
...
| * ARM: zynq: Do not perform reset at the end of thorMichal Simek2016-04-131-0/+1
| * ARM: zynq: Support systems with more memory banksMichal Simek2016-04-132-13/+123
| * ARM: zynq: Use memory initialization based on DTS fileMichal Simek2016-04-131-5/+5
| * ARM: zynq: Fix usb phy node for ZyboMichal Simek2016-04-131-1/+1
| * ARM: zynq: Extend microzed board supportMichal Simek2016-04-133-1/+43
| * ARM: zynq: Add missing qspi for xm013Michal Simek2016-04-131-1/+6
| * ARM: zynq: Create empty line below headersMichal Simek2016-04-131-0/+1
| * ARM: zynq: Align spi and qspi node locationsMichal Simek2016-04-135-37/+37
| * ARM: zynq: zc706: Add adv7511 on i2c busChristian Kohn2016-04-131-0/+15
| * ARM: zynq: zc702: Add adv7511 on i2c busChristian Kohn2016-04-131-0/+15
| * ARM: zynq: DT: Add ethernet phy reset informationPunnaiah Choudary Kalluri2016-04-131-0/+2
| * ARM: zynq: Fix bootargs in board dtsiMichal Simek2016-04-138-8/+8
| * ARM: zynq: Align devcfg nodeMichal Simek2016-04-131-0/+4
| * ARM: dts: Updated devicetree bindings for Zynq 7000 platformMoritz Fischer2016-04-131-0/+1
| * ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.Moritz Fischer2016-04-131-0/+7
| * ARM: zynq: Add interrupt-controller property to gpio nodesMichal Simek2016-04-131-0/+2
* | Merge git://www.denx.de/git/u-boot-cfi-flashTom Rini2016-04-131-1/+1
|\ \
| * | mtd: cfi: Unlock current sector instead of sector 0 before buffered writeRouven Behr2016-04-131-1/+1
* | | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-04-1349-92/+2442
|\ \ \ | |/ / |/| |
| * | mx6slevk: imximage.cfg: update to fix tINIT3 and tIH-CA violationsTom Rini2016-04-031-2/+2
| * | mx6qarm2: imximage_mx6dl.cfg update to fix tINIT3 violationTom Rini2016-04-031-2/+2
| * | mx7_common: Define CONFIG_SYS_MALLOC_LEN in the board fileFabio Estevam2016-04-033-3/+7
| * | warp7: Pass the UART base definitionFabio Estevam2016-04-031-0/+2
| * | mx6sabresd: Remove unneeded enable_lvds() functionFabio Estevam2016-04-031-11/+1
| * | arm: mxs: Update MX28EVK configMarek Vasut2016-04-032-0/+4
| * | imx: mx7d: move MX7D to Kconfig entryPeng Fan2016-03-262-1/+2
| * | imx: mx6sx: move MX6SX to Kconfig entryPeng Fan2016-03-264-3/+5
| * | arm: mx6: Add CCV xPress board supportStefan Roese2016-03-2610-0/+837
| * | arm: mx6: Add UART8 base address for i.MX6ULStefan Roese2016-03-261-0/+1
| * | warp7: Add initial supportFabio Estevam2016-03-268-0/+386
| * | mx7_common: Put early/late init configs into board fileFabio Estevam2016-03-262-3/+3
| * | mx6sabresd: Use VESA 1024x768 timingsFabio Estevam2016-03-251-14/+14
| * | mx27: 16-bit wide watchdog registersLeonid Iziumtsev2016-03-252-7/+7
| * | mx6sabre_common: Fix U-Boot corruption after 'saveenv'Fabio Estevam2016-03-251-1/+1
| * | arm: imx6: Switch DDR3 calibration to wait_for_bit()Marek Vasut2016-03-251-32/+12
| * | arm: mx5: Enable NAND TrimFFS on M53EVKMarek Vasut2016-03-251-0/+1
| * | imx: print ARM clock for clocks commandPeng Fan2016-03-251-0/+1
| * | imx: mx6ul configure the PMIC_STBY_REQ pin as open drainPeng Fan2016-03-251-1/+11
| * | imx: mx6ul: skip setting ahb ratePeng Fan2016-03-251-7/+12
| * | imx: mx6: Fix incorrect clear mmdc_ch0 handshake maskYe Li2016-03-251-1/+4
| * | Merge branch 'next'Stefano Babic2016-03-2015-4/+1127
| |\ \
| | * | mx7: Distinguish between dual and solo versionsFabio Estevam2016-03-093-0/+21
| | * | mx7dsabresd: Define serial port locallyFabio Estevam2016-03-092-1/+2
| | * | mx7_common: Remove unexisting optionsFabio Estevam2016-03-091-3/+0
| | * | arm: imx: Add support for GE Bx50v3 boardsAkshay Bhat2016-03-0910-0/+1104
* | | | Merge git://www.denx.de/git/u-boot-marvellTom Rini2016-04-124-2/+116
|\ \ \ \
| * | | | arm: mvebu: theadorable: Remove Board name output in checkboardStefan Roese2016-04-121-2/+0
| * | | | arm: mvebu: theadorable: Add PEX-switch detection and reset codeStefan Roese2016-04-122-0/+70
| * | | | arm: mvebu: theadorable: Enable 2nd I2C controllerStefan Roese2016-04-121-0/+1
| * | | | arm: mvebu: Add base address for 2nd I2C controllerStefan Roese2016-04-121-0/+1
OpenPOWER on IntegriCloud