diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/BC3450.h | 541 | ||||
| -rw-r--r-- | include/configs/JSE.h | 276 | ||||
| -rw-r--r-- | include/configs/MPC8308RDB.h | 3 | ||||
| -rw-r--r-- | include/configs/MPC8313ERDB.h | 3 | ||||
| -rw-r--r-- | include/configs/MPC8315ERDB.h | 3 | ||||
| -rw-r--r-- | include/configs/MPC8323ERDB.h | 3 | ||||
| -rw-r--r-- | include/configs/MPC832XEMDS.h | 3 | ||||
| -rw-r--r-- | include/configs/MPC8349EMDS.h | 3 | ||||
| -rw-r--r-- | include/configs/MPC8349ITX.h | 3 | ||||
| -rw-r--r-- | include/configs/MPC837XEMDS.h | 3 | ||||
| -rw-r--r-- | include/configs/TB5200.h | 496 | ||||
| -rw-r--r-- | include/configs/TQM834x.h | 3 | ||||
| -rw-r--r-- | include/configs/W7OLMC.h | 314 | ||||
| -rw-r--r-- | include/configs/W7OLMG.h | 317 | ||||
| -rw-r--r-- | include/configs/aev.h | 390 | ||||
| -rw-r--r-- | include/configs/bur_am335x_common.h | 2 | ||||
| -rw-r--r-- | include/configs/galaxy5200.h | 431 | ||||
| -rw-r--r-- | include/configs/km/km8309-common.h | 3 | ||||
| -rw-r--r-- | include/configs/km/km8321-common.h | 3 | ||||
| -rw-r--r-- | include/configs/km8360.h | 3 | ||||
| -rw-r--r-- | include/configs/korat.h | 550 | ||||
| -rw-r--r-- | include/configs/mpc8308_p1m.h | 3 | ||||
| -rw-r--r-- | include/configs/sbc8349.h | 3 | ||||
| -rw-r--r-- | include/configs/ve8313.h | 3 | ||||
| -rw-r--r-- | include/configs/vme8349.h | 3 |
25 files changed, 50 insertions, 3315 deletions
diff --git a/include/configs/BC3450.h b/include/configs/BC3450.h deleted file mode 100644 index 802e9cce1f..0000000000 --- a/include/configs/BC3450.h +++ /dev/null @@ -1,541 +0,0 @@ -/* - * -- Version 1.1 -- - * - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004-2005 - * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de - * - * (C) Copyright 2005 - * Stefan Strobl, GERSYS GmbH, stefan.strobl@gersys.de. - * - * History: - * 1.1 - add define CONFIG_ZERO_BOOTDELAY_CHECK - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */ -#define CONFIG_TQM5200 1 /* ... on a TQM5200 module */ - -#define CONFIG_BC3450 1 /* ... on a BC3450 mainboard */ -#define CONFIG_BC3450_PS2 1 /* + a PS/2 converter onboard */ -#define CONFIG_BC3450_IDE 1 /* + IDE drives (Compact Flash) */ -#define CONFIG_BC3450_USB 1 /* + USB support */ -# define CONFIG_FAT 1 /* + FAT support */ -# define CONFIG_EXT2 1 /* + EXT2 support */ -#undef CONFIG_BC3450_BUZZER /* + Buzzer onboard */ -#undef CONFIG_BC3450_CAN /* + CAN transceiver */ -#undef CONFIG_BC3450_DS1340 /* + a RTC DS1340 onboard */ -#undef CONFIG_BC3450_DS3231 /* + a RTC DS3231 onboard tbd */ -#undef CONFIG_BC3450_AC97 /* + AC97 on PSC2, tbd */ -#define CONFIG_BC3450_FP 1 /* + enable FP O/P */ -#undef CONFIG_BC3450_CRT /* + enable CRT O/P (Debug only!) */ - -/* - * Valid values for CONFIG_SYS_TEXT_BASE are: - * 0xFC000000 boot low (standard configuration with room for - * max 64 MByte Flash ROM) - * 0x00100000 boot from RAM (for testing only) - */ -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFC000000 -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * AT-PS/2 Multiplexer - */ -#ifdef CONFIG_BC3450_PS2 -# define CONFIG_PS2KBD /* AT-PS/2 Keyboard */ -# define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ -# define CONFIG_PS2SERIAL 6 /* .. on PSC6 */ -# define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */ -# define CONFIG_BOARD_EARLY_INIT_R -#endif /* CONFIG_BC3450_PS2 */ - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -# define CONFIG_PCI 1 -# define CONFIG_PCI_PNP 1 -/* #define CONFIG_PCI_SCAN_SHOW 1 */ -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -/*#define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */ -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_NS8382X 1 - -/* - * Video console - */ -# define CONFIG_VIDEO -# define CONFIG_VIDEO_SM501 -# define CONFIG_VIDEO_SM501_32BPP -# define CONFIG_CFB_CONSOLE -# define CONFIG_VIDEO_LOGO -# define CONFIG_VGA_AS_SINGLE_DEVICE -# define CONFIG_CONSOLE_EXTRA_INFO /* display Board/Device-Infos */ -# define CONFIG_VIDEO_SW_CURSOR -# define CONFIG_SPLASH_SCREEN -# define CONFIG_SYS_CONSOLE_IS_IN_ENV - -/* - * Partitions - */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - -/* - * USB - */ -#ifdef CONFIG_BC3450_USB -# define CONFIG_USB_OHCI -# define CONFIG_USB_STORAGE -#endif /* CONFIG_BC3450_USB */ - -/* - * POST support - */ -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_I2C) - -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -# define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 -#endif /* CONFIG_POST */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SNTP -#define CONFIG_CMD_BSP - -#ifdef CONFIG_VIDEO - #define CONFIG_CMD_BMP -#endif - -#ifdef CONFIG_BC3450_IDE - #define CONFIG_CMD_IDE -#endif - -#if defined(CONFIG_BC3450_IDE) || defined(CONFIG_BC3450_USB) - #ifdef CONFIG_FAT - #define CONFIG_CMD_FAT - #endif - - #ifdef CONFIG_EXT2 - #define CONFIG_CMD_EXT2 - #endif -#endif - -#ifdef CONFIG_BC3450_USB - #define CONFIG_CMD_USB -#endif - -#ifdef CONFIG_PCI - #define CONFIG_CMD_PCI -#endif - -#ifdef CONFIG_POST - #define CONFIG_CMD_DIAG -#endif - - -#define CONFIG_TIMESTAMP /* display image timestamps */ - -#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) /* Boot low */ -# define CONFIG_SYS_LOWBOOT 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo;" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "ipaddr=192.168.1.10\0" \ - "serverip=192.168.1.3\0" \ - "netmask=255.255.255.0\0" \ - "hostname=bc3450\0" \ - "rootpath=/opt/eldk/ppc_6xx\0" \ - "kernel_addr=fc0a0000\0" \ - "ramdisk_addr=fc1c0000\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath)\0" \ - "ideargs=setenv bootargs root=/dev/hda2 ro\0" \ - "addip=setenv bootargs $(bootargs) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ - ":$(hostname):$(netdev):off panic=1\0" \ - "addcons=setenv bootargs $(bootargs) " \ - "console=ttyS0,$(baudrate) console=tty0\0" \ - "flash_self=run ramargs addip addcons;" \ - "bootm $(kernel_addr) $(ramdisk_addr)\0" \ - "flash_nfs=run nfsargs addip addcons; bootm $(kernel_addr)\0" \ - "net_nfs=tftp 200000 $(bootfile); " \ - "run nfsargs addip addcons; bootm\0" \ - "ide_nfs=run nfsargs addip addcons; " \ - "disk 200000 0:1; bootm\0" \ - "ide_ide=run ideargs addip addcons; " \ - "disk 200000 0:1; bootm\0" \ - "usb_self=run usbload; run ramargs addip addcons; " \ - "bootm 200000 400000\0" \ - "usbload=usb reset; usb scan; usbboot 200000 0:1; " \ - "usbboot 400000 0:2\0" \ - "bootfile=uImage\0" \ - "load=tftp 200000 $(u-boot)\0" \ - "u-boot=u-boot.bin\0" \ - "update=protect off FC000000 FC05FFFF;" \ - "erase FC000000 FC05FFFF;" \ - "cp.b 200000 FC000000 $(filesize);" \ - "protect on FC000000 FC05FFFF\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -/* - * PCI Bus clocking configuration - * - * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock - * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. - */ -#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK) -# define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ -#endif - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */ - -/* - * I2C clock frequency - * - * Please notice, that the resulting clock frequency could differ from the - * configured value. This is because the I2C clock is derived from system - * clock over a frequency divider with only a few divider values. U-boot - * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated - * approximation allways lies below the configured value, never above. - */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration for I²C EEPROM M24C32 - * M24C64 should work also. For other EEPROMs config should be verified. - * - * The TQM5200 module may hold an EEPROM at address 0x50. - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x (TQM) */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -/* - * RTC configuration - */ -#if defined (CONFIG_BC3450_DS1340) && !defined (CONFIG_BC3450_DS3231) -# define CONFIG_RTC_M41T11 1 -# define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#else -# define CONFIG_RTC_MPC5200 1 /* use MPC5200 internal RTC */ -# define CONFIG_BOARD_EARLY_INIT_R -#endif - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE /* 0xFC000000 */ - -/* use CFI flash driver if no module variant is spezified */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START } -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ - -#if !defined(CONFIG_SYS_LOWBOOT) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000) -#else /* CONFIG_SYS_LOWBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000) -#endif /* CONFIG_SYS_LOWBOOT */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -/* Dynamic MTD partition support */ -#define CONFIG_CMD_MTDPARTS -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ -#define CONFIG_FLASH_CFI_MTD -#define MTDIDS_DEFAULT "nor0=TQM5200-0" -#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \ - "1408k(kernel)," \ - "2m(initrd)," \ - "4m(small-fs)," \ - "16m(big-fs)," \ - "8m(misc)" - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use ON-Chip SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -# define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE -#else -# define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE -#endif /*CONFIG_POST*/ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - * - * Define CONFIG_MPC5xxx_MII10 to force FEC at 10MBIT - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -#undef CONFIG_MPC5xxx_MII10 -#define CONFIG_PHY_ADDR 0x00 - -/* - * GPIO configuration on BC3450 - * - * PSC1: UART1 (Service-UART) [0x xxxxxxx4] - * PSC2: UART2 [0x xxxxxx4x] - * or: AC/97 if CONFIG_BC3450_AC97 [0x xxxxxx2x] - * PSC3: USB2 [0x xxxxx1xx] - * USB: UART4(ext.)/UART5(int.) [0x xxxx2xxx] - * (this has to match - * CONFIG_USB_CONFIG which is - * used by usb_ohci.c to set - * the USB ports) - * Eth: 10/100Mbit Ethernet [0x xxx0xxxx] - * (this is reset to '5' - * in FEC driver: fec.c) - * PSC6: UART6 (int. to PS/2 contr.) [0x xx5xxxxx] - * ATA/CS: ??? [0x x1xxxxxx] - * FIXME! UM Fig 2-10 suggests [0x x0xxxxxx] - * CS1: Use Pin gpio_wkup_6 as second - * SDRAM chip select (mem_cs1) - * Timer: CAN2 / SPI - * I2C: CAN1 / I²C2 [0x bxxxxxxx] - */ -#ifdef CONFIG_BC3450_AC97 -# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502124 -#else /* PSC2=UART2 */ -# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502144 -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max no of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg. Buffer Size */ - -#define CONFIG_SYS_ALT_MEMTEST /* Enable an alternative, */ - /* more extensive mem test */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Enable loopw command. - */ -#define CONFIG_LOOPW - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 -# define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ -#else -# define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ -#endif -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -/* automatic configuration of chip selects */ -#ifdef CONFIG_TQM5200 -# define CONFIG_LAST_STAGE_INIT -#endif /* CONFIG_TQM5200 */ - -/* - * SRAM - Do not map below 2 GB in address space, because this area is used - * for SDRAM autosizing. - */ -#ifdef CONFIG_TQM5200 -# define CONFIG_SYS_CS2_START 0xE5000000 -# define CONFIG_SYS_CS2_SIZE 0x100000 /* 1 MByte */ -# define CONFIG_SYS_CS2_CFG 0x0004D930 -#endif /* CONFIG_TQM5200 */ - -/* - * Grafic controller - Do not map below 2 GB in address space, because this - * area is used for SDRAM autosizing. - */ -#ifdef CONFIG_TQM5200 -# define SM501_FB_BASE 0xE0000000 -# define CONFIG_SYS_CS1_START (SM501_FB_BASE) -# define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */ -# define CONFIG_SYS_CS1_CFG 0x8F48FF70 -# define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000 -#endif /* CONFIG_TQM5200 */ - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for */ - /* flash and SM501 */ - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/* - * USB stuff - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00002000 /* we're using Port 2 */ - -/* - * IDE/ATA stuff Supports IDE harddisk - */ -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#endif /* __CONFIG_H */ diff --git a/include/configs/JSE.h b/include/configs/JSE.h deleted file mode 100644 index 5cc25576ae..0000000000 --- a/include/configs/JSE.h +++ /dev/null @@ -1,276 +0,0 @@ -/* - * (C) Copyright 2003 Picture Elements, Inc. - * Stephen Williams <steve@icarus.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options for the JSE board - * (Theoretically easy to change, but the board is fixed.) - */ - -#define CONFIG_JSE 1 - /* JSE has a PPC405GPr */ -#define CONFIG_405GP 1 - /* ... with a 33MHz OSC. connected to the SysCLK input */ -#define CONFIG_SYS_CLK_FREQ 33333333 - /* ... with on-chip memory here (4KBytes) */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000 - /* Do not set up locked dcache as init ram. */ -#undef CONFIG_SYS_INIT_DCACHE_CS - -#define CONFIG_SYS_TEXT_BASE 0xFFF80000 - - /* Map the SystemACE chip (CS#1) here. (Must be a multiple of 1Meg) */ -#define CONFIG_SYSTEMACE 1 -#define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000 -#define CONFIG_SYS_SYSTEMACE_WIDTH 8 -#define CONFIG_DOS_PARTITION 1 - - /* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - /* ... place INIT RAM in the OCM address */ -# define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR - /* ... give it the whole init ram */ -# define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE - /* ... Shave a bit off the end for global data */ -# define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - /* ... and place the stack pointer at the top of what's left. */ -# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - - /* Enable board_pre_init function */ -#define CONFIG_BOARD_PRE_INIT 1 -#define CONFIG_BOARD_EARLY_INIT_F 1 - /* Disable post-clk setup init function */ -#undef CONFIG_BOARD_POSTCLK_INIT - /* Disable call to post_init_f: late init function. */ -#undef CONFIG_POST - /* Enable DRAM test. */ -#define CONFIG_SYS_DRAM_TEST 1 - /* Enable misc_init_r function. */ -#define CONFIG_MISC_INIT_R 1 - - /* JSE has EEPROM chips that are good for environment. */ -#undef CONFIG_ENV_IS_IN_NVRAM -#undef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_IS_IN_EEPROM 1 -#undef CONFIG_ENV_IS_NOWHERE - - /* This is the 7bit address of the device, not including P. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 - /* After the device address, need one more address byte. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - /* The EEPROM is 512 bytes. */ -#define CONFIG_SYS_EEPROM_SIZE 512 - /* The EEPROM can do 16byte ( 1 << 4 ) page writes. */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - /* Put the environment in the second half. */ -#define CONFIG_ENV_OFFSET 0x00 -#define CONFIG_ENV_SIZE 512 - - /* The JSE connects UART1 to the console tap connector. */ -#define CONFIG_CONS_INDEX 2 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - - /* Set console baudrate to 9600 */ -#define CONFIG_BAUDRATE 9600 - -/* - * Configuration related to auto-boot. - * - * CONFIG_BOOTDELAY sets the delay (in seconds) that U-Boot will wait - * before resorting to autoboot. This value can be overridden by the - * bootdelay environment variable. - * - * CONFIG_AUTOBOOT_PROMPT is the string that U-Boot emits to warn the - * user that an autoboot will happen. - * - * CONFIG_BOOTCOMMAND is the sequence of commands that U-Boot will - * execute to boot the JSE. This loads the uimage and initrd.img files - * from CompactFlash into memory, then boots them from memory. - * - * CONFIG_BOOTARGS is the arguments passed to the Linux kernel to get - * it going on the JSE. - */ -#define CONFIG_BOOTDELAY 5 -#define CONFIG_BOOTARGS "root=/dev/ram0 init=/linuxrc rw" -#define CONFIG_BOOTCOMMAND "fatload ace 0 2000000 uimage; fatload ace 0 2100000 initrd.img; bootm 2000000 2100000" - - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 1 /* PHY address */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING - - - /* watchdog disabled */ -#undef CONFIG_WATCHDOG - /* SPD EEPROM (sdram speed config) disabled */ -#undef CONFIG_SPD_EEPROM -#undef SPD_EEPROM_ADDRESS - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* - * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. - * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. - * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value. - * The Linux BASE_BAUD define should match this configuration. - * baseBaud = cpuClock/(uartDivisor*16) - * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, - * set Linux BASE_BAUD to 403200. - */ -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CONFIG_SYS_BASE_BAUD 691200 - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#undef CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - -/*----------------------------------------------------------------------- - * External peripheral base address - *----------------------------------------------------------------------- - */ -#undef CONFIG_IDE_LED /* no led for ide supported */ -#undef CONFIG_IDE_RESET /* no reset for ide supported */ - -#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000 -#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000 -#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000 - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFF80000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ - - -/* Configuration Port location */ -#define CONFIG_PORT_ADDR 0xF0000500 - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif -#endif /* __CONFIG_H */ diff --git a/include/configs/MPC8308RDB.h b/include/configs/MPC8308RDB.h index bf974fd461..1ab23796cf 100644 --- a/include/configs/MPC8308RDB.h +++ b/include/configs/MPC8308RDB.h @@ -9,6 +9,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * High Level Configuration Options */ diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index dd8122965a..d9a19c3694 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -10,6 +10,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * High Level Configuration Options */ diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h index 98e907245a..1384f360bd 100644 --- a/include/configs/MPC8315ERDB.h +++ b/include/configs/MPC8315ERDB.h @@ -9,6 +9,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) #define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h index 65a63e2b7f..2dd71b7ed9 100644 --- a/include/configs/MPC8323ERDB.h +++ b/include/configs/MPC8323ERDB.h @@ -9,6 +9,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * High Level Configuration Options */ diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h index 1735b3c521..14abd3512c 100644 --- a/include/configs/MPC832XEMDS.h +++ b/include/configs/MPC832XEMDS.h @@ -7,6 +7,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * High Level Configuration Options */ diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h index 6b7d648944..17f230f4a1 100644 --- a/include/configs/MPC8349EMDS.h +++ b/include/configs/MPC8349EMDS.h @@ -13,6 +13,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * High Level Configuration Options */ diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index 398918a940..245712504c 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -40,6 +40,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + #if (CONFIG_SYS_TEXT_BASE == 0xFE000000) #define CONFIG_SYS_LOWBOOT #endif diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 832c10f5c0..85f5c40ede 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -8,6 +8,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * High Level Configuration Options */ diff --git a/include/configs/TB5200.h b/include/configs/TB5200.h deleted file mode 100644 index b4daedceea..0000000000 --- a/include/configs/TB5200.h +++ /dev/null @@ -1,496 +0,0 @@ -/* - * (C) Copyright 2003-2006 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004-2006 - * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ -#define CONFIG_TQM5200 1 /* ... on TQM5200 module */ -#define CONFIG_TB5200 1 /* ... on a TB5200 base board */ - -/* - * Valid values for CONFIG_SYS_TEXT_BASE are: - * 0xFC000000 boot low (standard configuration with room for - * max 64 MByte Flash ROM) - * 0xFFF00000 boot high (for a backup copy of U-Boot) - * 0x00100000 boot from RAM (for testing only) - */ -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFC000000 -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* default console is on PSC1 */ -#define CONFIG_PSC_CONSOLE2 6 /* second console is on PSC6 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * Video console - */ -#if 1 -#define CONFIG_VIDEO -#define CONFIG_VIDEO_SM501 -#define CONFIG_VIDEO_SM501_32BPP -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_LOGO -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_CONSOLE_EXTRA_INFO -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_SPLASH_SCREEN -#define CONFIG_SYS_CONSOLE_IS_IN_ENV -#endif - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - -/* USB */ -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE - -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_I2C) - -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 -#endif - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SNTP -#define CONFIG_CMD_BSP -#define CONFIG_CMD_USB - -#ifdef CONFIG_VIDEO -#define CONFIG_CMD_BMP -#endif - -#ifdef CONFIG_POST -#define CONFIG_CMD_DIAG -#endif - - -#define CONFIG_TIMESTAMP /* display image timestamps */ - -#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) /* Boot low */ -# define CONFIG_SYS_LOWBOOT 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#if defined(CONFIG_TQM5200_B) -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "rootpath=/opt/eldk/ppc_6xx\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "bootfile=/tftpboot/tqm5200/uImage\0" \ - "load=tftp 200000 ${u-boot}\0" \ - "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \ - "update=protect off FC000000 FC07FFFF;" \ - "erase FC000000 FC07FFFF;" \ - "cp.b 200000 FC000000 ${filesize};" \ - "protect on FC000000 FC07FFFF\0" \ - "" -#else -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "rootpath=/opt/eldk/ppc_6xx\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "bootfile=/tftpboot/tqm5200/uImage\0" \ - "load=tftp 200000 $(u-boot)\0" \ - "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \ - "update=protect off FC000000 FC05FFFF;" \ - "erase FC000000 FC05FFFF;" \ - "cp.b 200000 FC000000 ${filesize};" \ - "protect on FC000000 FC05FFFF\0" \ - "" -#endif /* CONFIG_TQM5200_B */ - -#define CONFIG_BOOTCOMMAND "run net_nfs" - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK) -/* - * PCI Bus clocking configuration - * - * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock - * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. - */ -#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ -#endif - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */ - -/* - * I2C clock frequency - * - * Please notice, that the resulting clock frequency could differ from the - * configured value. This is because the I2C clock is derived from system - * clock over a frequency divider with only a few divider values. U-boot - * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated - * approximation allways lies below the configured value, never above. - */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work - * also). For other EEPROMs configuration should be verified. On Mini-FAP the - * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the - * same configuration could be used. - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 - -/* List of I2C addresses to be verified by POST */ -#undef CONFIG_SYS_POST_I2C_ADDRS -#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR, \ - CONFIG_SYS_I2C_SLAVE} - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE /* 0xFC000000 */ - -/* use CFI flash driver */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START } -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 - -#if !defined(CONFIG_SYS_LOWBOOT) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000) -#else /* CONFIG_SYS_LOWBOOT */ -#if defined(CONFIG_TQM5200_B) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00080000) -#else -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000) -#endif /* CONFIG_TQM5200_B */ -#endif /* CONFIG_SYS_LOWBOOT */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ - -/* Dynamic MTD partition support */ -#define CONFIG_CMD_MTDPARTS -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ -#define CONFIG_FLASH_CFI_MTD -#define MTDIDS_DEFAULT "nor0=TQM5200-0" -#if defined(CONFIG_TQM5200_B) -#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:768k(firmware)," \ - "1280k(kernel)," \ - "2m(initrd)," \ - "4m(small-fs)," \ - "16m(big-fs)," \ - "8m(misc)" -#else -#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \ - "1408k(kernel)," \ - "2m(initrd)," \ - "4m(small-fs)," \ - "16m(big-fs)," \ - "8m(misc)" -#endif /* CONFIG_TQM5200_B */ - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x10000 -#if defined(CONFIG_TQM5200_B) -#define CONFIG_ENV_SECT_SIZE 0x40000 -#else -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#endif /* CONFIG_TQM5200_B */ - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use ON-Chip SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE -#else -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE -#endif - - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#if defined(CONFIG_TQM5200_B) -#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ -#else -#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ -#endif /* CONFIG_TQM5200_B */ -#define CONFIG_SYS_MALLOC_LEN (1024 << 10) /* Reserve 1024 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -/* - * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb - */ -/* #define CONFIG_MPC5xxx_FEC_MII10 */ -#define CONFIG_PHY_ADDR 0x00 - -/* - * GPIO configuration - * - * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1): - * Bit 0 (mask: 0x80000000): 1 - * use ALT CAN position: Bits 2-3 (mask: 0x30000000): - * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting. - * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1. - * Use for REV200 STK52XX boards. Do not use with REV100 modules - * (because, there I2C1 is used as I2C bus) - * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 - * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030) - * 000 -> All PSC2 pins are GIOPs - * 001 -> CAN1/2 on PSC2 pins - * Use for REV100 STK52xx boards - * use PSC3: Bits 20:23 (mask: 0x00000300): - * 0001 -> USB2 - * 0000 -> GPIO - * use PSC6: - * on STK52xx: - * use as UART. Pins PSC6_0 to PSC6_3 are used. - * Bits 9:11 (mask: 0x00700000): - * 101 -> PSC6 : Extended POST test is not available - * on MINI-FAP and TQM5200_IB: - * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000): - * 000 -> PSC6 could not be used as UART, CODEC or IrDA - * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST - * tests. - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x81500114 - -/* - * RTC configuration - */ -#define CONFIG_RTC_M41T11 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* because Linux uses the same base - year */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* Enable an alternate, more extensive memory test */ -#define CONFIG_SYS_ALT_MEMTEST - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * Enable loopw command. - */ -#define CONFIG_LOOPW - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 -#define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ -#else -#define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ -#endif -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_LAST_STAGE_INIT - -/* - * SRAM - Do not map below 2 GB in address space, because this area is used - * for SDRAM autosizing. - */ -#define CONFIG_SYS_CS2_START 0xE5000000 -#define CONFIG_SYS_CS2_SIZE 0x100000 /* 1 MByte */ -#define CONFIG_SYS_CS2_CFG 0x0004D930 - -/* - * Grafic controller - Do not map below 2 GB in address space, because this - * area is used for SDRAM autosizing. - */ -#define SM501_FB_BASE 0xE0000000 -#define CONFIG_SYS_CS1_START (SM501_FB_BASE) -#define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */ -#define CONFIG_SYS_CS1_CFG 0x8F48FF70 -#define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000 - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */ - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00001000 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#endif /* __CONFIG_H */ diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h index 6762e3a57e..7b496c853f 100644 --- a/include/configs/TQM834x.h +++ b/include/configs/TQM834x.h @@ -12,6 +12,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * High Level Configuration Options */ diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h deleted file mode 100644 index 895ad4611b..0000000000 --- a/include/configs/W7OLMC.h +++ /dev/null @@ -1,314 +0,0 @@ -/* - * (C) Copyright 2001 - * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405GP 1 /* This is a PPC405GP CPU */ -#define CONFIG_W7O 1 /* ...on a Wave 7 Optics board */ -#define CONFIG_W7OLMC 1 /* ...specifically an LMC */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_MISC_INIT_F 1 /* and misc_init_f() */ -#define CONFIG_MISC_INIT_R 1 /* and misc_init_r() */ - -#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ - -#define CONFIG_BAUDRATE 9600 -#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ - -#if 1 -#define CONFIG_BOOTCOMMAND "bootvx" /* VxWorks boot command */ -#else -#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ -#endif - -#undef CONFIG_BOOTARGS - -#define CONFIG_LOADADDR F0080000 - -#define CONFIG_ETHADDR 00:06:0D:00:00:00 /* Default, overridden at boot */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE -#define CONFIG_IPADDR 192.168.1.1 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_SERVERIP 192.168.1.2 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* disallow baudrate change */ - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address */ - -#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PCI -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_BEDBUG -#define CONFIG_CMD_DATE -#define CONFIG_CMD_I2C -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_BSP -#define CONFIG_CMD_REGINFO - -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#define CONFIG_HW_WATCHDOG /* HW Watchdog, board specific */ - -#define CONFIG_SPD_EEPROM /* SPD EEPROM for SDRAM param. */ -#define CONFIG_SPDDRAM_SILENT /* No output if spd fails */ -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "Wave7Optics> " /* Monitor Command Prompt */ -#undef CONFIG_SYS_HUSH_PARSER /* No hush parse for U-Boot */ -#ifdef CONFIG_SYS_HUSH_PARSER -#endif -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#define CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CONFIG_SYS_BASE_BAUD 384000 - - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE {9600} - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info (bd_t) */ - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ -#define CONFIG_PCI_PNP /* pci plug-and-play */ -/* resource configuration */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0156 /* PCI Device ID: 405GP */ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ - -/*----------------------------------------------------------------------- - * Set up values for external bus controller - * used by cpu_init.c - *----------------------------------------------------------------------- - */ - /* Don't use PerWE instead of PCI_INT ( these functions share a pin ) */ -#undef CONFIG_USE_PERWE - -/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - -/* bank 0 is boot flash */ -/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CONFIG_SYS_W7O_EBC_PB0AP 0x03050440 -/* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */ -#define CONFIG_SYS_W7O_EBC_PB0CR 0xFFE38000 - -/* bank 1 is main flash */ -/* BME=0,TWT=11,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CONFIG_SYS_EBC_PB1AP 0x05850240 -/* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */ -#define CONFIG_SYS_EBC_PB1CR 0xF00FC000 - -/* bank 2 is RTC/NVRAM */ -/* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CONFIG_SYS_EBC_PB2AP 0x03000440 -/* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */ -#define CONFIG_SYS_EBC_PB2CR 0xFC018000 - -/* bank 3 is FPGA 0 */ -/* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */ -#define CONFIG_SYS_EBC_PB3AP 0x02000400 -/* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */ -#define CONFIG_SYS_EBC_PB3CR 0xFD01A000 - -/* bank 4 is FPGA 1 */ -/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */ -#define CONFIG_SYS_EBC_PB4AP 0x02000400 -/* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */ -#define CONFIG_SYS_EBC_PB4CR 0xFD11A000 - -/* bank 5 is FPGA 2 */ -/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */ -#define CONFIG_SYS_EBC_PB5AP 0x02000400 -/* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */ -#define CONFIG_SYS_EBC_PB5CR 0xFD21A000 - -/* bank 6 is unused */ -/* PB6AP = 0 */ -#define CONFIG_SYS_EBC_PB6AP 0x00000000 -/* PB6CR = 0 */ -#define CONFIG_SYS_EBC_PB6CR 0x00000000 - -/* bank 7 is LED register */ -/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CONFIG_SYS_W7O_EBC_PB7AP 0x03050440 -/* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */ -#define CONFIG_SYS_W7O_EBC_PB7CR 0xFE01C000 - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFFC0000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sec on 1 chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout, Flash Erase, in ms */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout, Flash Write, in ms */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use real Flash protection */ - -#if 1 /* Use NVRAM for environment variables */ -/*----------------------------------------------------------------------- - * NVRAM organization - */ -#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for env vars */ -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfc000000 /* NVRAM base address */ -#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */ -#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */ -/*define CONFIG_ENV_ADDR \ - (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) Env */ -#define CONFIG_ENV_ADDR CONFIG_SYS_NVRAM_BASE_ADDR - -#else /* Use Boot Flash for environment variables */ -/*----------------------------------------------------------------------- - * Flash EEPROM for environment - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x10000 /* Total Size of env. sector */ - -#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sec tot sze */ -#endif - -/*----------------------------------------------------------------------- - * I2C EEPROM (CAT24WC08) for environment - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ - /* 16 byte page write mode using*/ - /* last 4 bits of the address */ -#define CONFIG_SYS_I2C_MULTI_EEPROMS -/*----------------------------------------------------------------------- - * Definitions for Serial Presence Detect EEPROM address - * (to get SDRAM settings) - */ -#define SPD_EEPROM_ADDRESS 0x50 /* XXX conflicting address!!! XXX */ - -/* - * Init Memory Controller: - */ -#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0xF0000000 /* FLASH bank #1 */ - -/* On Chip Memory location */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in RAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * FPGA(s) configuration - */ -#define CONFIG_SYS_FPGA_IMAGE_LEN 0x80000 /* 512KB FPGA image */ -#define CONFIG_NUM_FPGAS 3 /* Number of FPGAs on board */ -#define CONFIG_MAX_FPGAS 6 /* Maximum number of FPGAs */ -#define CONFIG_FPGAS_BASE 0xFD000000L /* Base address of FPGAs */ -#define CONFIG_FPGAS_BANK_SIZE 0x00100000L /* FPGAs' mmap bank size */ - -#endif /* __CONFIG_H */ diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h deleted file mode 100644 index 2a38116dd1..0000000000 --- a/include/configs/W7OLMG.h +++ /dev/null @@ -1,317 +0,0 @@ -/* - * (C) Copyright 2001 - * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405GP 1 /* This is a PPC405GP CPU */ -#define CONFIG_W7O 1 /* ...on a Wave 7 Optics board */ -#define CONFIG_W7OLMG 1 /* ...specifically an LMG */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_MISC_INIT_F 1 /* and misc_init_f() */ -#define CONFIG_MISC_INIT_R 1 /* and misc_init_r() */ - -#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ - -#define CONFIG_BAUDRATE 9600 -#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ - -#if 1 -#define CONFIG_BOOTCOMMAND "bootvx" /* VxWorks boot command */ -#else -#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ -#endif - -#undef CONFIG_BOOTARGS - -#define CONFIG_LOADADDR F0080000 - -#define CONFIG_ETHADDR 00:06:0D:00:00:00 /* Default, overridden at boot */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE -#define CONFIG_IPADDR 192.168.1.1 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_SERVERIP 192.168.1.2 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* disallow baudrate change */ - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address */ - -#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ -#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {2, 4} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PCI -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_BEDBUG -#define CONFIG_CMD_DATE -#define CONFIG_CMD_I2C -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_BSP -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_DTT - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#define CONFIG_HW_WATCHDOG /* HW Watchdog, board specific */ - -#define CONFIG_SPD_EEPROM /* SPD EEPROM for SDRAM param. */ -#define CONFIG_SPDDRAM_SILENT /* No output if spd fails */ -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "Wave7Optics> " /* Monitor Command Prompt */ -#undef CONFIG_SYS_HUSH_PARSER /* No hush parse for U-Boot */ -#ifdef CONFIG_SYS_HUSH_PARSER -#endif -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#define CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CONFIG_SYS_BASE_BAUD 384000 - - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE {9600} - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info (bd_t) */ - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ -#define CONFIG_PCI_PNP /* pci plug-and-play */ -/* resource configuration */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0156 /* PCI Device ID: 405GP */ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ - -/*----------------------------------------------------------------------- - * Set up values for external bus controller - * used by cpu_init.c - *----------------------------------------------------------------------- - */ - /* use PerWE instead of PCI_INT ( these functions share a pin ) */ -#define CONFIG_USE_PERWE 1 - -/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - -/* bank 0 is boot flash */ -/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CONFIG_SYS_W7O_EBC_PB0AP 0x03050440 -/* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */ -#define CONFIG_SYS_W7O_EBC_PB0CR 0xFFE38000 - -/* bank 1 is main flash */ -/* BME=0,TWT=9,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CONFIG_SYS_EBC_PB1AP 0x04850240 -/* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */ -#define CONFIG_SYS_EBC_PB1CR 0xF00FC000 - -/* bank 2 is RTC/NVRAM */ -/* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CONFIG_SYS_EBC_PB2AP 0x03000440 -/* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */ -#define CONFIG_SYS_EBC_PB2CR 0xFC018000 - -/* bank 3 is FPGA 0 */ -/* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */ -#define CONFIG_SYS_EBC_PB3AP 0x02000400 -/* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */ -#define CONFIG_SYS_EBC_PB3CR 0xFD01A000 - -/* bank 4 is SAM 8 bit range */ -/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */ -#define CONFIG_SYS_EBC_PB4AP 0x02840380 -/* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */ -#define CONFIG_SYS_EBC_PB4CR 0xFE878000 - -/* bank 5 is SAM 16 bit range */ -/* BME=0,TWT=10,CSN=2,OEN=0,WBN=0,WBF=0,TH=6,RE=1,SOR=1,BEM=0,PEN=0 */ -#define CONFIG_SYS_EBC_PB5AP 0x05040d80 -/* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */ -#define CONFIG_SYS_EBC_PB5CR 0xFD87A000 - -/* bank 6 is unused */ -/* PB6AP = 0 */ -#define CONFIG_SYS_EBC_PB6AP 0x00000000 -/* PB6CR = 0 */ -#define CONFIG_SYS_EBC_PB6CR 0x00000000 - -/* bank 7 is LED register */ -/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CONFIG_SYS_W7O_EBC_PB7AP 0x03050440 -/* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */ -#define CONFIG_SYS_W7O_EBC_PB7CR 0xFE01C000 - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFFC0000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 196 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sec on 1 chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout, Flash Erase, in ms */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout, Flash Write, in ms */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use real Flash protection */ - -#if 1 /* Use NVRAM for environment variables */ -/*----------------------------------------------------------------------- - * NVRAM organization - */ -#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for env vars */ -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfc000000 /* NVRAM base address */ -#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */ -#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */ -/*define CONFIG_ENV_ADDR \ - (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) Env */ -#define CONFIG_ENV_ADDR CONFIG_SYS_NVRAM_BASE_ADDR - -#else /* Use Boot Flash for environment variables */ -/*----------------------------------------------------------------------- - * Flash EEPROM for environment - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x10000 /* Total Size of env. sector */ - -#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sec tot sze */ -#endif - -/*----------------------------------------------------------------------- - * I2C EEPROM (ATMEL 24C04N) - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM ATMEL 24C04N */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_I2C_MULTI_EEPROMS -/*----------------------------------------------------------------------- - * Definitions for Serial Presence Detect EEPROM address - * (to get SDRAM settings) - */ -#define SPD_EEPROM_ADDRESS 0x50 /* XXX conflicting address!!! XXX */ - -/* - * Init Memory Controller: - */ -#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0xF0000000 /* FLASH bank #1 */ - -/* On Chip Memory location */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in RAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * FPGA(s) configuration - */ -#define CONFIG_SYS_FPGA_IMAGE_LEN 0x80000 /* 512KB FPGA image */ -#define CONFIG_NUM_FPGAS 1 /* Number of FPGAs on board */ -#define CONFIG_MAX_FPGAS 6 /* Maximum number of FPGAs */ -#define CONFIG_FPGAS_BASE 0xFD000000L /* Base address of FPGAs */ -#define CONFIG_FPGAS_BANK_SIZE 0x00100000L /* FPGAs' mmap bank size */ - -#endif /* __CONFIG_H */ diff --git a/include/configs/aev.h b/include/configs/aev.h deleted file mode 100644 index 2dffcfbed3..0000000000 --- a/include/configs/aev.h +++ /dev/null @@ -1,390 +0,0 @@ -/* - * (C) Copyright 2003-2006 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004-2005 - * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ -#define CONFIG_TQM5200 1 /* ... on TQM5200 module */ -#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */ -#define CONFIG_STK52XX 1 /* ... on a STK52XX base board */ -#define CONFIG_STK52XX_REV100 1 /* define for revision 100 baseboards */ -#define CONFIG_AEVFIFO 1 -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -/* - * Valid values for CONFIG_SYS_TEXT_BASE are: - * 0xFC000000 boot low (standard configuration with room for - * max 64 MByte Flash ROM) - * 0xFFF00000 boot high (for a backup copy of U-Boot) - * 0x00100000 boot from RAM (for testing only) - */ -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFC000000 -#endif - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -#ifdef CONFIG_AEVFIFO -#define CONFIG_PCI 1 -#define CONFIG_PCI_PNP 1 -/* #define CONFIG_PCI_SCAN_SHOW 1 */ -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -#define CONFIG_EEPRO100 1 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_NS8382X 1 -#endif /* CONFIG_AEVFIFO */ - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_I2C) - -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 -#endif - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_MII -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SNTP - -#ifdef CONFIG_POST -#define CONFIG_CMD_DIAG -#endif - - -#define CONFIG_TIMESTAMP /* display image timestamps */ - -#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) /* Boot low */ -# define CONFIG_SYS_LOWBOOT 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "rootpath=/opt/eldk/ppc_6xx\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath} " \ - "console=ttyS0,${baudrate}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "bootfile=/tftpboot/tqm5200/uImage\0" \ - "load=tftp 200000 ${u-boot}\0" \ - "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \ - "update=protect off FC000000 FC05FFFF;" \ - "erase FC000000 FC05FFFF;" \ - "cp.b 200000 FC000000 ${filesize};" \ - "protect on FC000000 FC05FFFF\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run net_nfs" - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK) -/* - * PCI Bus clocking configuration - * - * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock - * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. - */ -#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ -#endif - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#ifdef CONFIG_TQM5200_REV100 -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ -#else -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ -#endif - -/* - * I2C clock frequency - * - * Please notice, that the resulting clock frequency could differ from the - * configured value. This is because the I2C clock is derived from system - * clock over a frequency divider with only a few divider values. U-boot - * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated - * approximation allways lies below the configured value, never above. - */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work - * also). For other EEPROMs configuration should be verified. On Mini-FAP the - * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the - * same configuration could be used. - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE /* 0xFC000000 */ - -/* use CFI flash driver if no module variant is spezified */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START } -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ - -#if !defined(CONFIG_SYS_LOWBOOT) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000) -#else /* CONFIG_SYS_LOWBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000) -#endif /* CONFIG_SYS_LOWBOOT */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use ON-Chip SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE -#else -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE -#endif - - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -/* - * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb - */ -/* #define CONFIG_MPC5xxx_FEC_MII10 */ -#define CONFIG_PHY_ADDR 0x00 - -/* - * GPIO configuration - * - * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1): - * Bit 0 (mask: 0x80000000): 1 - * use ALT CAN position: Bits 2-3 (mask: 0x30000000): - * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting. - * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1. - * Use for REV200 STK52XX boards. Do not use with REV100 modules - * (because, there I2C1 is used as I2C bus) - * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 - * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030) - * 000 -> All PSC2 pins are GIOPs - * 001 -> CAN1/2 on PSC2 pins - * Use for REV100 STK52xx boards - * use PSC6: - * on STK52xx: - * use as UART. Pins PSC6_0 to PSC6_3 are used. - * Bits 9:11 (mask: 0x00700000): - * 101 -> PSC6 : Extended POST test is not available - * on MINI-FAP and TQM5200_IB: - * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000): - * 000 -> PSC6 could not be used as UART, CODEC or IrDA - * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST - * tests. - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x81500014 - -/* - * RTC configuration - */ -#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -/* Enable an alternate, more extensive memory test */ -#define CONFIG_SYS_ALT_MEMTEST - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Enable loopw command. - */ -#define CONFIG_LOOPW - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 -#define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ -#else -#define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ -#endif -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_LAST_STAGE_INIT - -/* - * SRAM - Do not map below 2 GB in address space, because this area is used - * for SDRAM autosizing. - */ -#define CONFIG_SYS_CS2_START 0xE5000000 -#define CONFIG_SYS_CS2_SIZE 0x80000 /* 512 kByte */ -#define CONFIG_SYS_CS2_CFG 0x0004D930 - -/* - * Grafic controller - Do not map below 2 GB in address space, because this - * area is used for SDRAM autosizing. - */ -#define SM501_FB_BASE 0xE0000000 -#define CONFIG_SYS_CS1_START (SM501_FB_BASE) -#define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */ -#define CONFIG_SYS_CS1_CFG 0x8F48FF70 -#define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000 - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */ - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -#endif /* __CONFIG_H */ diff --git a/include/configs/bur_am335x_common.h b/include/configs/bur_am335x_common.h index 377e6cfd67..240fc464bc 100644 --- a/include/configs/bur_am335x_common.h +++ b/include/configs/bur_am335x_common.h @@ -142,6 +142,8 @@ #define CONFIG_SYS_PROMPT "U-Boot (BuR V2.0)# " #define CONFIG_SYS_CONSOLE_INFO_QUIET #define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE /* As stated above, the following choices are optional. */ #define CONFIG_SYS_LONGHELP diff --git a/include/configs/galaxy5200.h b/include/configs/galaxy5200.h deleted file mode 100644 index b555d82ddc..0000000000 --- a/include/configs/galaxy5200.h +++ /dev/null @@ -1,431 +0,0 @@ -/* - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2006 - * Eric Schumann, Phytec Messatechnik GmbH - * - * (C) Copyright 2009 - * Jon Smirl <jonsmirl@gmail.com> - * - * (C) Copyright 2009 - * Eric Millbrandt, DEKA Research and Development Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_BOARDINFO "galaxy5200" - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ -#define CONFIG_SYS_MPC5XXX_CLKIN 33333333 /* ... running at 33.333333MHz */ - -/* - * Valid values for CONFIG_SYS_TEXT_BASE are: - * 0xFFF00000 boot high (standard configuration) - * 0xFE000000 boot low - * 0x00100000 boot from RAM (for testing only) does not work - */ -#ifdef CONFIG_galaxy5200_LOWBOOT -#define CONFIG_SYS_TEXT_BASE 0xFE000000 -#endif - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 /* Standard: boot high */ -#endif - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 4 /* console is on PSC4 -> */ - /* define gps port conf. */ - /* register later on to */ - /* enable UART function! */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP -#define CONFIG_CMD_PING -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_USB -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_FAT - -#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ - -#if (CONFIG_SYS_TEXT_BASE == 0xFE000000) /* Boot low */ -#define CONFIG_SYS_LOWBOOT 1 -#endif -/* RAMBOOT will be defined automatically in memory section */ - -#define MTDIDS_DEFAULT "nor0=physmap-flash.0" -#define MTDPARTS_DEFAULT "mtdparts=physmap-flash.0:256k(ubootl)," \ - "1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)" - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 10 /* autoboot after 10 seconds */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow stopping of boot process */ - /* even with bootdelay=0 */ -#define CONFIG_BOOT_RETRY_TIME 120 /* Reset if no command is entered */ -#define CONFIG_RESET_TO_RETRY - -#define CONFIG_PREBOOT "echo;" \ - "echo Welcome to U-Boot;"\ - "echo" - -#define CONFIG_BOOTCOMMAND "go ff300004 0; go ff300004 2 2;" \ - "bootm ff040000 ff900000 fffc0000" -#define CONFIG_BOOTARGS "console=ttyPSC0,115200" -#define CONFIG_EXTRA_ENV_SETTINGS "epson=yes\0" - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#define CONFIG_SYS_XLB_PIPELINING 1 - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_INIT_MPC5XXX /* Reset devices on i2c bus */ - -/* - * EEPROM CAT24WC32 configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */ -#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ -#define CONFIG_SYS_EEPROM_SIZE 4096 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15 - -/* - * RTC configuration - */ -#define RTC -#define CONFIG_RTC_DS3231 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/* - * Flash configuration - */ - -#define CONFIG_SYS_FLASH_BASE 0xfe000000 -/* - * The flash size is autoconfigured, but arch/powerpc/cpu/mpc5xxx/cpu_init.c needs this - * variable defined - */ -#define CONFIG_SYS_FLASH_SIZE 0x02000000 -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_MAX_FLASH_SECT 259 /* max num of sects on one chip */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ - /* (= chip selects) */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE - -/* - * Use hardware protection. This seems required, as the BDI uses hardware - * protection. Without this, U-Boot can't work with this sectors as its - * protection is software only by default. - */ -#define CONFIG_SYS_FLASH_PROTECTION 1 - -/* - * Environment settings - */ - -#define CONFIG_ENV_IS_IN_EEPROM 1 -#define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */ - /* beginning of the EEPROM */ -#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE - -#define CONFIG_ENV_OVERWRITE 1 - -/* - * SDRAM configuration - */ -#define SDRAM_DDR 1 -#define SDRAM_MODE 0x018D0000 -#define SDRAM_EMODE 0x40090000 -#define SDRAM_CONTROL 0x71500F00 -#define SDRAM_CONFIG1 0x73711930 -#define SDRAM_CONFIG2 0x47770000 - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 /* MBAR has to be switched by other */ - /* bootloader or debugger config */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM - -/* End of used area in SPRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* Chip Select configuration for NAND flash */ -#define CONFIG_SYS_CS1_START 0x20000000 -#define CONFIG_SYS_CS1_SIZE 0x90000 -#define CONFIG_SYS_CS1_CFG 0x00025b00 - -/* Chip Select configuration for Epson S1D13513 */ -#define CONFIG_SYS_CS3_START 0x10000000 -#define CONFIG_SYS_CS3_SIZE 0x400000 -#define CONFIG_SYS_CS3_CFG 0xffff3d10 - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -#define CONFIG_PHY_ADDR 0x01 -#define CONFIG_NO_AUTOLOAD 1 - -/* - * GPIO configuration - * - * GPS port configuration - * - * [29:31] = 01x - * AC97 on PSC1 - * PSC1_0 -> AC97 SDATA out - * PSC1_1 -> AC97 SDTA in - * PSC1_2 -> AC97 SYNC out - * PSC1_3 -> AC97 bitclock out - * PSC1_4 -> AC97 reset out - * - * [28] = Reserved - * - * [25:27] = 110 - * SPI on PSC2 - * PSC2_0 -> MOSI - * PSC2_1 -> MISO - * PSC2_2 -> n/a - * PSC2_3 -> CLK - * PSC2_4 -> SS - * - * [24] = Reserved - * - * [20:23] = 0001 - * USB on PSC3 - * PSC3_0 -> USB_OE OE out - * PSC3_1 -> USB_TXN Tx- out - * PSC3_2 -> USB_TXP Tx+ out - * PSC3_3 -> USB_TXD - * PSC3_4 -> USB_RXP Rx+ in - * PSC3_5 -> USB_RXN Rx- in - * PSC3_6 -> USB_PWR PortPower out - * PSC3_7 -> USB_SPEED speed out - * PSC3_8 -> USB_SUSPEND suspend - * PSC3_9 -> USB_OVRCURNT overcurrent in - * - * [18:19] = 10 - * Two UARTs - * - * [17] = 0 - * USB differential mode - * - * [16] = 1 - * PCI disabled - * - * [12:15] = 0101 - * Ethernet 100Mbit with MD - * ETH_0 -> ETH Txen - * ETH_1 -> ETH TxD0 - * ETH_2 -> ETH TxD1 - * ETH_3 -> ETH TxD2 - * ETH_4 -> ETH TxD3 - * ETH_5 -> ETH Txerr - * ETH_6 -> ETH MDC - * ETH_7 -> ETH MDIO - * ETH_8 -> ETH RxDv - * ETH_9 -> ETH RxCLK - * ETH_10 -> ETH Collision - * ETH_11 -> ETH TxD - * ETH_12 -> ETH RxD0 - * ETH_13 -> ETH RxD1 - * ETH_14 -> ETH RxD2 - * ETH_15 -> ETH RxD3 - * ETH_16 -> ETH Rxerr - * ETH_17 -> ETH CRS - * - * [9:11] = 111 - * SPI on PSC6 - * PSC6_0 -> MISO - * PSC6_1 -> SS# - * PSC6_2 -> MOSI - * PSC6_3 -> CLK - * - * [8] = 0 - * IrDA/USB 48MHz clock generated internally - * - * [6:7] = 01 - * ATA chip selects on csb_4/5 - * CSB_4 -> ATA_CS0 out - * CSB_5 -> ATA_CS1 out - * - * [5] = 1 - * PSC3_4 is used as CS6 - * - * [4] = 1 - * PSC3_5 is used as CS7 - * - * [2:3] = 00 - * No Alternatives - * - * [1] = 0 - * gpio_wkup_7 is GPIO - * - * [0] = 0 - * gpio_wkup_6 is GPIO - * - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x0d75a162 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "uboot> " /* Monitor Command Prompt */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */ - -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_SYS_HUSH_PARSER 1 - -#define CONFIG_CRC32_VERIFY 1 - -#define CONFIG_BOOTP_DNS -#define CONFIG_BOOTP_DNS2 -#define CONFIG_BOOTP_SEND_HOSTNAME - -#define CONFIG_VERSION_VARIABLE 1 - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -/* no burst access on the LPB */ -#define CONFIG_SYS_CS_BURST 0x00000000 -/* one deadcycle for the 33MHz statemachine */ -#define CONFIG_SYS_CS_DEADCYCLE 0x33333331 - -#define CONFIG_SYS_BOOTCS_CFG 0x0002d900 -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/* - * USB settings - */ -#define CONFIG_USB_CLOCK 0x0001bbbb -/* USB is on PSC3 */ -#define CONFIG_PSC3_USB -#define CONFIG_USB_CONFIG 0x00000100 -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE - -/* - * IDE/ATA stuff Supports IDE harddisk - */ -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET 1 /* reset for ide supported */ -#define CONFIG_IDE_PREINIT -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 -#define CONFIG_ATAPI 1 - -/* we enable IDE and FAT support, so we also need partition support */ -#define CONFIG_DOS_PARTITION 1 - -/* - * Open Firmware flat tree - */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,5200@0" -#define OF_TBCLK CONFIG_SYS_MPC5XXX_CLKIN -#define OF_SOC "soc5200@f0000000" -#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2600" - -#endif /* __CONFIG_H */ diff --git a/include/configs/km/km8309-common.h b/include/configs/km/km8309-common.h index c8df23b534..ec133f9e92 100644 --- a/include/configs/km/km8309-common.h +++ b/include/configs/km/km8309-common.h @@ -10,6 +10,9 @@ #ifndef __CONFIG_KM8309_COMMON_H #define __CONFIG_KM8309_COMMON_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * High Level Configuration Options */ diff --git a/include/configs/km/km8321-common.h b/include/configs/km/km8321-common.h index 149895cb7e..058b0ab42b 100644 --- a/include/configs/km/km8321-common.h +++ b/include/configs/km/km8321-common.h @@ -23,6 +23,9 @@ #ifndef __CONFIG_KM8321_COMMON_H #define __CONFIG_KM8321_COMMON_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * High Level Configuration Options */ diff --git a/include/configs/km8360.h b/include/configs/km8360.h index f5ac32a332..04cde46cc5 100644 --- a/include/configs/km8360.h +++ b/include/configs/km8360.h @@ -9,6 +9,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* KMBEC FPGA (PRIO) */ #define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 #define CONFIG_SYS_KMBEC_FPGA_SIZE 64 diff --git a/include/configs/korat.h b/include/configs/korat.h deleted file mode 100644 index 5494a6007d..0000000000 --- a/include/configs/korat.h +++ /dev/null @@ -1,550 +0,0 @@ -/* - * (C) Copyright 2007-2009 - * Larry Johnson, lrj@acm.org - * - * (C) Copyright 2006-2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2006 - * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com - * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * korat.h - configuration for Korat board - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_440EPX 1 /* Specific PPC440EPx */ -#define CONFIG_SYS_CLK_FREQ 33333333 - -#ifdef CONFIG_KORAT_PERMANENT -#define CONFIG_SYS_TEXT_BASE 0xFFFA0000 -#else -#define CONFIG_SYS_TEXT_BASE 0xF7F60000 -#endif - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ - -/* - * Manufacturer's information serial EEPROM parameters - */ -#define MAN_DATA_EEPROM_ADDR 0x53 /* EEPROM I2C address */ -#define MAN_INFO_FIELD 2 -#define MAN_INFO_LENGTH 9 -#define MAN_MAC_ADDR_FIELD 3 -#define MAN_MAC_ADDR_LENGTH 12 - -/* - * Base addresses -- Note these are effective addresses where the actual - * resources get mapped (not physical addresses). - */ -#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kiB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kiB for malloc() */ - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CONFIG_SYS_FLASH0_SIZE 0x01000000 -#define CONFIG_SYS_FLASH0_ADDR (-CONFIG_SYS_FLASH0_SIZE) -#define CONFIG_SYS_FLASH1_TOP 0xF8000000 -#define CONFIG_SYS_FLASH1_MAX_SIZE 0x08000000 -#define CONFIG_SYS_FLASH1_ADDR (CONFIG_SYS_FLASH1_TOP - CONFIG_SYS_FLASH1_MAX_SIZE) -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH1_ADDR /* start of FLASH */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */ -#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE -#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */ -#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PCI_MEMBASE2 (CONFIG_SYS_PCI_MEMBASE + 0x20000000) - -#define CONFIG_SYS_USB2D0_BASE 0xe0000100 -#define CONFIG_SYS_USB_DEVICE 0xe0000000 -#define CONFIG_SYS_USB_HOST 0xe0000400 -#define CONFIG_SYS_CPLD_BASE 0xc0000000 - -/* - * Initial RAM & stack pointer - */ -/* 440EPx has 16KB of internal SRAM, so no need for D-Cache */ -#undef CONFIG_SYS_INIT_RAM_DCACHE -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */ -#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() -#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -/* - * Environment - */ -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environ vars */ - -/* - * FLASH related - */ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_FLASH_CFI_LEGACY /* Allow hard-coded config for FLASH0 */ - -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1_ADDR, CONFIG_SYS_FLASH0_ADDR } - -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ - -#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH1_TOP - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -/* - * DDR SDRAM - */ -#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ -#define CONFIG_ZERO_SDRAM /* Zero SDRAM after setup */ -#define CONFIG_DDR_ECC /* Use ECC when available */ -#define SPD_EEPROM_ADDRESS {0x50} -#define CONFIG_PROG_SDRAM_TLB -#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4 KiB as */ - /* per 440EPx Errata CHIP_11 */ - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - -#define CONFIG_SYS_I2C_MULTI_EEPROMS -#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -/* I2C RTC */ -#define CONFIG_RTC_M41T60 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/* I2C SYSMON (LM73) */ -#define CONFIG_DTT_LM73 1 /* National Semi's LM73 */ -#define CONFIG_DTT_SENSORS {2} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_MIN_TEMP -30 - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_cf\\\" to mount from CompactFlash(R);" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#define CONFIG_HOSTNAME korat - -/* Note: kernel_addr and ramdisk_addr assume that FLASH1 is 64 MiB. */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - "u_boot=korat/u-boot.bin\0" \ - "load=tftp 200000 ${u_boot}\0" \ - "update=protect off F7F60000 F7FBFFFF;erase F7F60000 F7FBFFFF;" \ - "cp.b ${fileaddr} F7F60000 ${filesize};protect on " \ - "F7F60000 F7FBFFFF\0" \ - "upd=run load update\0" \ - "bootfile=korat/uImage\0" \ - "dtb=korat/korat.dtb\0" \ - "kernel_addr=F4000000\0" \ - "ramdisk_addr=F4400000\0" \ - "dtb_addr=F41E0000\0" \ - "udl=tftp 200000 ${bootfile}; erase F4000000 F41DFFFF; " \ - "cp.b ${fileaddr} F4000000 ${filesize}\0" \ - "udd=tftp 200000 ${dtb}; erase F41E0000 F41FFFFF; " \ - "cp.b ${fileaddr} F41E0000 ${filesize}\0" \ - "ll=setenv kernel_addr 200000; setenv dtb_addr 1000000; " \ - "tftp ${kernel_addr} ${uImage}; tftp ${dtb_addr} " \ - "${dtb}\0" \ - "rd_size=73728\0" \ - "ramargs=setenv bootargs root=/dev/ram rw " \ - "ramdisk_size=${rd_size}\0" \ - "usbdev=sda1\0" \ - "usbargs=setenv bootargs root=/dev/${usbdev} ro rootdelay=10\0" \ - "rootpath=/opt/eldk/ppc_4xxFP\0" \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "pciclk=33\0" \ - "addide=setenv bootargs ${bootargs} ide=reverse " \ - "idebus=${pciclk}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_cf=run usbargs addide addip addtty; " \ - "bootm ${kernel_addr} - ${dtb_addr}\0" \ - "flash_nfs=run nfsargs addide addip addtty; " \ - "bootm ${kernel_addr} - ${dtb_addr}\0" \ - "flash_self=run ramargs addip addtty; " \ - "bootm ${kernel_addr} ${ramdisk_addr} ${dtb_addr}\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_cf" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 2 /* PHY address, See schematics */ -#define CONFIG_PHY_DYNAMIC_ANEG 1 - -#undef CONFIG_PHY_RESET /* Don't do software PHY reset */ -#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ - -#define CONFIG_HAS_ETH0 -#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx */ - /* buffers & descriptors */ -#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ -#define CONFIG_PHY1_ADDR 3 - -/* USB */ -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE - -/* Comment this out to enable USB 1.1 device */ -#define USB_2_0_DEVICE - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DTT -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_USB - -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_ECC | \ - CONFIG_SYS_POST_ETHER | \ - CONFIG_SYS_POST_FPU | \ - CONFIG_SYS_POST_I2C | \ - CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_RTC | \ - CONFIG_SYS_POST_SPR | \ - CONFIG_SYS_POST_UART) - -#define CONFIG_LOGBUFFER -#define CONFIG_SYS_POST_CACHE_ADDR 0xC8000000 /* free virtual address */ - -#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ - -#define CONFIG_SUPPORT_VFAT - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) - /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -/* - * Korat-specific options - */ -#define CONFIG_SYS_KORAT_MAN_RESET_MS 10000 /* timeout for manufacturer reset */ - -/* - * PCI stuff - */ -/* General PCI */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to */ - /* CONFIG_SYS_PCI_MEMBASE */ -/* Board-specific PCI */ -#define CONFIG_SYS_PCI_TARGET_INIT -#define CONFIG_SYS_PCI_MASTER_INIT -#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ -#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */ - -/* - * For booting Linux, the board info and command line data have to be in the - * first 8 MB of memory, since this is the maximum mapped by the Linux kernel - * during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * External Bus Controller (EBC) Setup - */ - -/* Memory Bank 0 (NOR-FLASH) initialization */ -#if CONFIG_SYS_FLASH0_SIZE == 0x01000000 -#define CONFIG_SYS_EBC_PB0AP 0x04017300 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH0_ADDR | 0x0009A000) -#elif CONFIG_SYS_FLASH0_SIZE == 0x04000000 -#define CONFIG_SYS_EBC_PB0AP 0x04017300 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH0_ADDR | 0x000DA000) -#else -#error Unable to configure chip select for current CONFIG_SYS_FLASH0_SIZE -#endif - -/* Memory Bank 1 (NOR-FLASH) initialization */ -#if CONFIG_SYS_FLASH1_MAX_SIZE == 0x08000000 -#define CONFIG_SYS_EBC_PB1AP 0x04017300 -#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_FLASH1_ADDR | 0x000FA000) -#else -#error Unable to configure chip select for current CONFIG_SYS_FLASH1_MAX_SIZE -#endif - -/* Memory Bank 2 (CPLD) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x04017300 -#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_CPLD_BASE | 0x00038000) - -/* - * GPIO Setup - * - * Korat GPIO usage: - * - * Init. - * Pin Source I/O value Function - * ------ ------ --- ----- --------------------------------- - * GPIO00 Alt1 I/O x PerAddr07 - * GPIO01 Alt1 I/O x PerAddr06 - * GPIO02 Alt1 I/O x PerAddr05 - * GPIO03 GPIO x x GPIO03 to expansion bus connector - * GPIO04 GPIO x x GPIO04 to expansion bus connector - * GPIO05 GPIO x x GPIO05 to expansion bus connector - * GPIO06 Alt1 O x PerCS1 (2nd NOR flash) - * GPIO07 Alt1 O x PerCS2 (CPLD) - * GPIO08 Alt1 O x PerCS3 to expansion bus connector - * GPIO09 Alt1 O x PerCS4 to expansion bus connector - * GPIO10 Alt1 O x PerCS5 to expansion bus connector - * GPIO11 Alt1 I x PerErr - * GPIO12 GPIO O 0 ATMega !Reset - * GPIO13 GPIO x x Test Point 2 (TP2) - * GPIO14 GPIO O 1 Write protect EEPROM #1 (0xA8) - * GPIO15 GPIO O 0 CPU Run LED !On - * GPIO16 Alt1 O x GMC1TxD0 - * GPIO17 Alt1 O x GMC1TxD1 - * GPIO18 Alt1 O x GMC1TxD2 - * GPIO19 Alt1 O x GMC1TxD3 - * GPIO20 Alt1 I x RejectPkt0 - * GPIO21 Alt1 I x RejectPkt1 - * GPIO22 GPIO I x PGOOD_DDR - * GPIO23 Alt1 O x SCPD0 - * GPIO24 Alt1 O x GMC0TxD2 - * GPIO25 Alt1 O x GMC0TxD3 - * GPIO26 GPIO? I/O x IIC0SDA (selected in SDR0_PFC4) - * GPIO27 GPIO O 0 PHY #0 1000BASE-X select - * GPIO28 GPIO O 0 PHY #1 1000BASE-X select - * GPIO29 GPIO I x Test jumper !Present - * GPIO30 GPIO I x SFP module #0 !Present - * GPIO31 GPIO I x SFP module #1 !Present - * - * GPIO32 GPIO O 1 SFP module #0 Tx !Enable - * GPIO33 GPIO O 1 SFP module #1 Tx !Enable - * GPIO34 Alt2 I x !UART1_CTS - * GPIO35 Alt2 O x !UART1_RTS - * GPIO36 Alt1 I x !UART0_CTS - * GPIO37 Alt1 O x !UART0_RTS - * GPIO38 Alt2 O x UART1_Tx - * GPIO39 Alt2 I x UART1_Rx - * GPIO40 Alt1 I x IRQ0 (Ethernet 0) - * GPIO41 Alt1 I x IRQ1 (Ethernet 1) - * GPIO42 Alt1 I x IRQ2 (PCI interrupt) - * GPIO43 Alt1 I x IRQ3 (System Alert from CPLD) - * GPIO44 xxxx x x (grounded through pulldown) - * GPIO45 GPIO O 0 PHY #0 Enable - * GPIO46 GPIO O 0 PHY #1 Enable - * GPIO47 GPIO I x Reset switch !Pressed - * GPIO48 GPIO I x Shutdown switch !Pressed - * GPIO49 xxxx x x (reserved for trace port) - * . . . . . - * . . . . . - * . . . . . - * GPIO63 xxxx x x (reserved for trace port) - */ - -#define CONFIG_SYS_GPIO_ATMEGA_RESET_ 12 -#define CONFIG_SYS_GPIO_ATMEGA_SS_ 13 -#define CONFIG_SYS_GPIO_PHY0_FIBER_SEL 27 -#define CONFIG_SYS_GPIO_PHY1_FIBER_SEL 28 -#define CONFIG_SYS_GPIO_SFP0_PRESENT_ 30 -#define CONFIG_SYS_GPIO_SFP1_PRESENT_ 31 -#define CONFIG_SYS_GPIO_SFP0_TX_EN_ 32 -#define CONFIG_SYS_GPIO_SFP1_TX_EN_ 33 -#define CONFIG_SYS_GPIO_PHY0_EN 45 -#define CONFIG_SYS_GPIO_PHY1_EN 46 -#define CONFIG_SYS_GPIO_RESET_PRESSED_ 47 - -/* - * PPC440 GPIO Configuration - */ -#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ -{ \ -/* GPIO Core 0 */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \ -{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \ -{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \ -{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 EBC_CS_N(1) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 EBC_CS_N(2) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS_N(3) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS_N(4) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5) */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO12 */ \ -{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO13 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO14 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO15 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO16 GMCTxD(4) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO17 GMCTxD(5) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO18 GMCTxD(6) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO19 GMCTxD(7) */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 RejectPkt0 */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 RejectPkt1 */ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO22 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 SCPD0 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO24 GMCTxD(2) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO25 GMCTxD(3) */ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26 */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 USB2D_TXVALID */ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \ -}, \ -{ \ -/* GPIO Core 1 */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 USB2D_OPMODE0 EBC_DATA(2) */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 USB2D_OPMODE1 EBC_DATA(3) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N EBC_DATA(0) UART3_SIN*/ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO37 UART0_RTS_N EBC_DATA(1) UART3_SOUT*/ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \ -} \ -} - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* Pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - -#endif /* __CONFIG_H */ diff --git a/include/configs/mpc8308_p1m.h b/include/configs/mpc8308_p1m.h index 4ae9afd4e5..d2ef1af62c 100644 --- a/include/configs/mpc8308_p1m.h +++ b/include/configs/mpc8308_p1m.h @@ -9,6 +9,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * High Level Configuration Options */ diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h index 2516a3e97e..2d264d2ef7 100644 --- a/include/configs/sbc8349.h +++ b/include/configs/sbc8349.h @@ -15,6 +15,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * High Level Configuration Options */ diff --git a/include/configs/ve8313.h b/include/configs/ve8313.h index 00787bbb28..bce94b3fdc 100644 --- a/include/configs/ve8313.h +++ b/include/configs/ve8313.h @@ -13,6 +13,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * High Level Configuration Options */ diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h index 175311cad9..c7730fc862 100644 --- a/include/configs/vme8349.h +++ b/include/configs/vme8349.h @@ -18,6 +18,9 @@ #ifndef __CONFIG_H #define __CONFIG_H +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + /* * Top level Makefile configuration choices */ |
