diff options
Diffstat (limited to 'include')
33 files changed, 290 insertions, 1480 deletions
diff --git a/include/configs/RPXsuper.h b/include/configs/RPXsuper.h index 5c19bd36e4..9d97f2fd37 100644 --- a/include/configs/RPXsuper.h +++ b/include/configs/RPXsuper.h @@ -35,7 +35,7 @@ #undef CONFIG_SYS_SBC_BOOT_LOW /* What should the base address of the main FLASH be and how big is - * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/sbc8260/config.mk + * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE. * The main FLASH is whichever is connected to *CS0. U-Boot expects * this to be the SIMM. */ diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h index da14a4f06b..1a7273b1ec 100644 --- a/include/configs/bf537-stamp.h +++ b/include/configs/bf537-stamp.h @@ -257,8 +257,15 @@ /* Define if want to do post memory test */ #undef CONFIG_POST #ifdef CONFIG_POST -#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */ -#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */ +#define CONFIG_SYS_POST_HOTKEYS_GPIO GPIO_PF5 +#define CONFIG_POST_BSPEC1_GPIO_LEDS \ + GPIO_PF6, GPIO_PF7, GPIO_PF8, GPIO_PF9, GPIO_PF10, GPIO_PF11, +#define CONFIG_POST_BSPEC2_GPIO_BUTTONS \ + GPIO_PF5, GPIO_PF4, GPIO_PF3, GPIO_PF2, +#define CONFIG_POST_BSPEC2_GPIO_NAMES \ + 10, 11, 12, 13, +#define CONFIG_SYS_POST_FLASH_START 11 +#define CONFIG_SYS_POST_FLASH_END 71 #endif /* These are for board tests */ diff --git a/include/configs/bf548-ezkit.h b/include/configs/bf548-ezkit.h index 3550fd3308..4862baa39d 100644 --- a/include/configs/bf548-ezkit.h +++ b/include/configs/bf548-ezkit.h @@ -197,8 +197,14 @@ /* Define if want to do post memory test */ #undef CONFIG_POST #ifdef CONFIG_POST -#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */ -#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */ +#define CONFIG_POST_BSPEC1_GPIO_LEDS \ + GPIO_PG6, GPIO_PG7, GPIO_PG8, GPIO_PG9, GPIO_PG10, GPIO_PG11, +#define CONFIG_POST_BSPEC2_GPIO_BUTTONS \ + GPIO_PB8, GPIO_PB9, GPIO_PB10, GPIO_PB11 +#define CONFIG_POST_BSPEC2_GPIO_NAMES \ + 13, 12, 11, 10, +#define CONFIG_SYS_POST_FLASH_START 10 +#define CONFIG_SYS_POST_FLASH_END 127 #endif diff --git a/include/configs/bfin_adi_common.h b/include/configs/bfin_adi_common.h index 57d9b97321..bae2d761b4 100644 --- a/include/configs/bfin_adi_common.h +++ b/include/configs/bfin_adi_common.h @@ -55,7 +55,6 @@ # endif # ifdef CONFIG_POST # define CONFIG_CMD_DIAG -# define CONFIG_POST_ALT_LIST # endif # ifdef CONFIG_RTC_BFIN # define CONFIG_CMD_DATE diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h index 710092de36..fbcbdb3aff 100644 --- a/include/configs/devkit8000.h +++ b/include/configs/devkit8000.h @@ -181,7 +181,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x82000000\0" \ - "console=ttyS2,115200n8\0" \ + "console=ttyO2,115200n8\0" \ "mmcdev=0\0" \ "vram=12M\0" \ "dvimode=1024x768MR-16@60\0" \ @@ -308,4 +308,50 @@ CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) +/* SRAM config */ +#define CONFIG_SYS_SRAM_START 0x40200000 +#define CONFIG_SYS_SRAM_SIZE 0x10000 + +/* Defines for SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_NAND_SIMPLE + +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_POWER_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" + +#define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/ +#define CONFIG_SPL_MAX_SIZE 0xB400 /* 45 K */ +#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK + +#define CONFIG_SPL_BSS_START_ADDR 0x80000000 /*CONFIG_SYS_SDRAM_BASE*/ +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 + +/* NAND boot config */ +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 +#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\ + 10, 11, 12, 13} + +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 3 + +#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \ + CONFIG_SYS_NAND_ECCSIZE) +#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \ + CONFIG_SYS_NAND_ECCSTEPS) + +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE + +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x200000 + #endif /* __CONFIG_H */ diff --git a/include/configs/efikamx.h b/include/configs/efikamx.h index b90e34299f..54f48e446d 100644 --- a/include/configs/efikamx.h +++ b/include/configs/efikamx.h @@ -31,6 +31,10 @@ */ /* An i.MX51 CPU */ #define CONFIG_MX51 + +#define machine_is_efikamx() (CONFIG_MACH_TYPE == MACH_TYPE_MX51_EFIKAMX) +#define machine_is_efikasb() (CONFIG_MACH_TYPE == MACH_TYPE_MX51_EFIKASB) + #include <asm/arch/imx-regs.h> #define CONFIG_SYS_MX5_HCLK 24000000 @@ -230,6 +234,6 @@ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) #define CONFIG_SYS_DDR_CLKSEL 0 -#define CONFIG_SYS_CLKTL_CBCDR 0x59E35100 +#define CONFIG_SYS_CLKTL_CBCDR 0x59E35145 #endif diff --git a/include/configs/gplugd.h b/include/configs/gplugd.h index cc14f49966..5f72163473 100644 --- a/include/configs/gplugd.h +++ b/include/configs/gplugd.h @@ -62,8 +62,34 @@ #define CONFIG_CMD_I2C #define CONFIG_CMD_AUTOSCRIPT #undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_NFS + +/* Disable DCACHE */ +#define CONFIG_SYS_DCACHE_OFF + +/* Network configuration */ +#ifdef CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_NET_MULTI +#define CONFIG_ARMADA100_FEC + +/* DHCP Support */ +#define CONFIG_CMD_DHCP +#define CONFIG_BOOTP_DHCP_REQUEST_DELAY 50000 +#endif /* CONFIG_CMD_NET */ + +/* GPIO Support */ +#define CONFIG_MARVELL_GPIO + +/* PHY configuration */ +#define CONFIG_MII +#define CONFIG_CMD_MII +#define CONFIG_RESET_PHY_R +/* 88E3015 register definition */ +#define PHY_LED_PAR_SEL_REG 22 +#define PHY_LED_MAN_REG 25 +#define PHY_LED_VAL 0x5b /* LINK LED1, ACT LED2 */ +/* GPIO Configuration for PHY */ +#define CONFIG_SYS_GPIO_PHY_RST 104 /* GPIO104 */ /* * mv-common.h should be defined after CMD configs since it used them diff --git a/include/configs/gw8260.h b/include/configs/gw8260.h index 35e6944d54..93d688581f 100644 --- a/include/configs/gw8260.h +++ b/include/configs/gw8260.h @@ -85,7 +85,7 @@ #define CONFIG_SYS_SBC_BOOT_LOW 1 /* What should the base address of the main FLASH be and how big is - * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/sbc8260/config.mk + * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE. * The main FLASH is whichever is connected to *CS0. U-Boot expects * this to be the SIMM. */ diff --git a/include/configs/imx31_litekit.h b/include/configs/imx31_litekit.h index b7f1cb3c75..5e976bc165 100644 --- a/include/configs/imx31_litekit.h +++ b/include/configs/imx31_litekit.h @@ -41,6 +41,8 @@ #define CONFIG_SYS_TEXT_BASE 0xa0000000 +#define CONFIG_MACH_TYPE MACH_TYPE_MX31LITE + /* Temporarily disabled */ #if 0 #define CONFIG_OF_LIBFDT 1 @@ -150,7 +152,7 @@ #define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024) #define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_SYS_SDRAM_BASE CSD0_BASE +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) diff --git a/include/configs/microblaze-generic.h b/include/configs/microblaze-generic.h index 090ab3bc2e..a811b76d7b 100644 --- a/include/configs/microblaze-generic.h +++ b/include/configs/microblaze-generic.h @@ -44,7 +44,7 @@ # define CONFIG_SYS_NS16550_REG_SIZE -4 # define CONFIG_CONS_INDEX 1 # define CONFIG_SYS_NS16550_COM1 \ - (XILINX_UART16550_BASEADDR + 0x1000 + 0x3) + (XILINX_UART16550_BASEADDR + 0x1000) # define CONFIG_SYS_NS16550_CLK XILINX_UART16550_CLOCK_HZ # define CONFIG_BAUDRATE 115200 @@ -60,6 +60,7 @@ /*#define CONFIG_SYS_RESET_ADDRESS CONFIG_SYS_TEXT_BASE*/ /* ethernet */ +#undef CONFIG_SYS_ENET #ifdef XILINX_EMACLITE_BASEADDR # define CONFIG_XILINX_EMACLITE 1 # define CONFIG_SYS_ENET @@ -243,6 +244,7 @@ #ifndef CONFIG_SYS_ENET # undef CONFIG_CMD_NET # undef CONFIG_NET_MULTI +# undef CONFIG_CMD_NFS #else # define CONFIG_CMD_PING # define CONFIG_CMD_DHCP @@ -325,4 +327,9 @@ # define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif +/* Enable flat device tree support */ +#define CONFIG_LMB 1 +#define CONFIG_FIT 1 +#define CONFIG_OF_LIBFDT 1 + #endif /* __CONFIG_H */ diff --git a/include/configs/mx25pdk.h b/include/configs/mx25pdk.h new file mode 100644 index 0000000000..0afae24b29 --- /dev/null +++ b/include/configs/mx25pdk.h @@ -0,0 +1,108 @@ +/* + * (C) Copyright 2011 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ + +#define CONFIG_MX25_CLK32 32768 /* OSC32K frequency */ +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_TEXT_BASE 0x81200000 + +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG + +#define CONFIG_MACH_TYPE MACH_TYPE_MX25_3DS + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024) + +/* Physical Memory Map */ + +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM_1 0x80000000 +#define PHYS_SDRAM_1_SIZE (64 * 1024 * 1024) + +#define CONFIG_BOARD_EARLY_INIT_F + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \ + GENERATED_GBL_DATA_SIZE) + +/* Memory Test */ +#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE/2) +#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE) + +/* Stack sizes */ +#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */ + +/* Serial Info */ +#define CONFIG_MXC_UART +#define CONFIG_SYS_MX25_UART1 +#define CONFIG_CONS_INDEX 1 /* use UART0 for console */ +#define CONFIG_BAUDRATE 115200 /* Default baud rate */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* No NOR flash present */ +#define CONFIG_ENV_OFFSET (6 * 64 * 1024) +#define CONFIG_ENV_SIZE (8 * 1024) +#define CONFIG_ENV_IS_NOWHERE + +#define CONFIG_SYS_NO_FLASH +#define CONFIG_SYS_64BIT_VSPRINTF + +/* U-Boot general configuration */ +#define CONFIG_SYS_PROMPT "MX25PDK U-Boot > " +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +/* Print buffer sz */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_LONGHELP + +/* U-Boot commands */ +#include <config_cmd_default.h> +#define CONFIG_CMD_CACHE + +/* Ethernet */ +#define CONFIG_FEC_MXC +#define CONFIG_FEC_MXC_PHYADDR 0x1f +#define CONFIG_MII +#define CONFIG_CMD_NET +#define CONFIG_NET_MULTI +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_LOADADDR 0x81000000 /* loadaddr env var */ +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "script=boot.scr\0" \ + "uimage=uImage\0" \ + "netargs=setenv bootargs console=ttymxc0,${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "bootcmd=run netargs; dhcp ${uimage}; bootm\0" \ + +#endif /* __CONFIG_H */ diff --git a/include/configs/mx31ads.h b/include/configs/mx31ads.h index adb2ee1ce9..0bea8589b6 100644 --- a/include/configs/mx31ads.h +++ b/include/configs/mx31ads.h @@ -35,6 +35,8 @@ #define CONFIG_SYS_TEXT_BASE 0xA0000000 +#define CONFIG_MACH_TYPE MACH_TYPE_MX31ADS + /* * Disabled for now due to build problems under Debian and a significant increase * in the final file size: 144260 vs. 109536 Bytes. diff --git a/include/configs/mx31pdk.h b/include/configs/mx31pdk.h index 1a5bdd1011..cd156d8b61 100644 --- a/include/configs/mx31pdk.h +++ b/include/configs/mx31pdk.h @@ -45,6 +45,8 @@ #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_INITRD_TAG +#define CONFIG_MACH_TYPE MACH_TYPE_MX31_3DS + #if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_SKIP_LOWLEVEL_INIT #endif @@ -124,7 +126,7 @@ * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "uboot> " +#define CONFIG_SYS_PROMPT "MX31PDK U-Boot > " #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h index 7d05dc8429..d62a4f2965 100644 --- a/include/configs/mx51evk.h +++ b/include/configs/mx51evk.h @@ -48,6 +48,7 @@ #define CONFIG_OF_LIBFDT 1 +#define CONFIG_MACH_TYPE MACH_TYPE_MX51_BABBAGE /* * Size of malloc() pool */ diff --git a/include/configs/mx53ard.h b/include/configs/mx53ard.h index c0b8d6a61a..26fc219ca2 100644 --- a/include/configs/mx53ard.h +++ b/include/configs/mx53ard.h @@ -29,6 +29,8 @@ #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_MACH_TYPE MACH_TYPE_MX53_ARD + #include <asm/arch/imx-regs.h> #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ diff --git a/include/configs/mx53evk.h b/include/configs/mx53evk.h index 7fb1d9aa75..b127b06cc3 100644 --- a/include/configs/mx53evk.h +++ b/include/configs/mx53evk.h @@ -29,6 +29,8 @@ #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_MACH_TYPE MACH_TYPE_MX53_EVK + #include <asm/arch/imx-regs.h> #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h index cfb38a5673..4091703732 100644 --- a/include/configs/mx53loco.h +++ b/include/configs/mx53loco.h @@ -30,6 +30,8 @@ #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_MACH_TYPE MACH_TYPE_MX53_LOCO + #include <asm/arch/imx-regs.h> #define CONFIG_CMDLINE_TAG diff --git a/include/configs/mx53smd.h b/include/configs/mx53smd.h index 49f8c6e8e7..261f0bc45c 100644 --- a/include/configs/mx53smd.h +++ b/include/configs/mx53smd.h @@ -1,7 +1,7 @@ /* * Copyright (C) 2011 Freescale Semiconductor, Inc. * - * Configuration settings for the MX53-SMDFreescale board. + * Configuration settings for the MX53SMD Freescale board. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -29,6 +29,8 @@ #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_MACH_TYPE MACH_TYPE_MX53_SMD + #include <asm/arch/imx-regs.h> #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h index fdc861d9d4..7af30c206d 100644 --- a/include/configs/omap3_evm.h +++ b/include/configs/omap3_evm.h @@ -200,7 +200,7 @@ "loadaddr=0x82000000\0" \ "usbtty=cdc_acm\0" \ "mmcdev=0\0" \ - "console=ttyS2,115200n8\0" \ + "console=ttyO0,115200n8\0" \ "mmcargs=setenv bootargs console=${console} " \ "root=/dev/mmcblk0p2 rw " \ "rootfstype=ext3 rootwait\0" \ diff --git a/include/configs/omap4_common.h b/include/configs/omap4_common.h index d8ac8c0b38..228eac5e37 100644 --- a/include/configs/omap4_common.h +++ b/include/configs/omap4_common.h @@ -98,7 +98,9 @@ #define CONFIG_I2C_MULTI_BUS 1 /* TWL6030 */ +#ifndef CONFIG_SPL_BUILD #define CONFIG_TWL6030_POWER 1 +#endif /* MMC */ #define CONFIG_GENERIC_MMC 1 diff --git a/include/configs/omap4_sdp4430.h b/include/configs/omap4_sdp4430.h index 39d715480e..9e03291ce1 100644 --- a/include/configs/omap4_sdp4430.h +++ b/include/configs/omap4_sdp4430.h @@ -37,7 +37,9 @@ #include <configs/omap4_common.h> /* Battery Charger */ +#ifndef CONFIG_SPL_BUILD #define CONFIG_CMD_BAT 1 +#endif /* ENV related config options */ #define CONFIG_ENV_IS_IN_MMC 1 diff --git a/include/configs/sacsng.h b/include/configs/sacsng.h index 32e0444a2f..914767ac1b 100644 --- a/include/configs/sacsng.h +++ b/include/configs/sacsng.h @@ -10,8 +10,7 @@ * Advent Networks, Inc. <http://www.adventnetworks.com> * Jay Monkman <jtm@smoothsmoothie.com> * - * Configuration settings for the WindRiver SBC8260 board. - * See http://www.windriver.com/products/html/sbc8260.html + * Configuration settings for the SACSng 8260 board. * * See file CREDITS for list of people who contributed to this * project. @@ -547,7 +546,6 @@ *****************************************************************************/ #define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ -#define CONFIG_SBC8260 1 /* on an EST SBC8260 Board */ #define CONFIG_SACSng 1 /* munged for the SACSng */ #define CONFIG_CPM2 1 /* Has a CPM2 */ diff --git a/include/configs/sbc8240.h b/include/configs/sbc8240.h deleted file mode 100644 index 2267677d2e..0000000000 --- a/include/configs/sbc8240.h +++ /dev/null @@ -1,364 +0,0 @@ -/* - * (C) Copyright 2001 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * Configuration settings for the sbc8240 board. - */ - -/* ------------------------------------------------------------------------- */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC824X 1 -#define CONFIG_MPC8240 1 -#define CONFIG_WRSBC8240 1 - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 9600 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -#define CONFIG_PREBOOT "echo;echo Welcome to U-Boot for the sbc8240;echo;echo Type \"? or help\" to get on-line help;echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_BOOTCOMMAND "version;echo;tftpboot $loadaddr $loadfile;bootvx" /* autoboot command */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "bootargs=$fei(0,0)host:/T221ppc/target/config/sbc8240/vxWorks.st " \ - "e=192.168.193.102 h=192.168.193.99 u=target pw=hello f=0x08 " \ - "tn=sbc8240 o=fei \0" \ - "env_startaddr=FFF70000\0" \ - "env_endaddr=FFF7FFFF\0" \ - "loadfile=vxWorks.st\0" \ - "loadaddr=0x01000000\0" \ - "net_load=tftpboot $loadaddr $loadfile\0" \ - "uboot_startaddr=FFF00000\0" \ - "uboot_endaddr=FFF3FFFF\0" \ - "update=tftp $loadaddr /u-boot.bin;" \ - "protect off $uboot_startaddr $uboot_endaddr;" \ - "era $uboot_startaddr $uboot_endaddr;" \ - "cp.b $loadaddr $uboot_startaddr $filesize;" \ - "protect on $uboot_startaddr $uboot_endaddr\0" \ - "zapenv=protect off $env_startaddr $env_endaddr;" \ - "era $env_startaddr $env_endaddr;" \ - "protect on $env_startaddr $env_endaddr\0" - -#define CONFIG_BOOTDELAY 5 - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -#define CONFIG_ENV_OVERWRITE - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_BSP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_SAVEENV -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_SDRAM - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ - -#if 1 -#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ -#endif -#ifdef CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#endif - -#define CONFIG_ETHADDR DE:AD:BE:EF:01:01 /* Ethernet address */ -#define CONFIG_IPADDR 192.168.193.102 -#define CONFIG_NETMASK 255.255.255.248 -#define CONFIG_SERVERIP 192.168.193.99 - -#define CONFIG_STATUS_LED /* Status LED enabled */ -#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ - -#define STATUS_LED_BIT 0x00000001 -#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -#define STATUS_LED_STATE STATUS_LED_BLINKING -#define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ -#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -#ifndef __ASSEMBLY__ -/* LEDs */ -typedef unsigned int led_id_t; - -#define __led_toggle(_msk) \ - do { \ - *((volatile char *) (CONFIG_SYS_LED_BASE)) ^= (_msk); \ - } while(0) - -#define __led_set(_msk, _st) \ - do { \ - if ((_st)) \ - *((volatile char *) (CONFIG_SYS_LED_BASE)) |= (_msk); \ - else \ - *((volatile char *) (CONFIG_SYS_LED_BASE)) &= ~(_msk); \ - } while(0) - -#define __led_init(msk, st) __led_set(msk, st) - -#endif - -#define CONFIG_MISC_INIT_R -#define CONFIG_SYS_LED_BASE 0xFFE80000 - -/* Print Buffer Size - */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */ - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFF00000 - -#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 - -#define CONFIG_SYS_EUMB_ADDR 0xFCE00000 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */ - - /* Maximum amount of RAM. - */ -#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 - -#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE -#undef CONFIG_SYS_RAMBOOT -#else -#define CONFIG_SYS_RAMBOOT -#endif - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area - */ - -#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL - -#define CONFIG_SYS_NS16550_REG_SIZE 1 - -#define CONFIG_SYS_NS16550_CLK 3686400 - -#define CONFIG_SYS_NS16550_COM1 0xFFF80000 - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - * For the detail description refer to the MPC8240 user's manual. - */ - -#define CONFIG_SYS_CLK_FREQ 33000000 -#define CONFIG_SYS_HZ 1000 -#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 3 - - /* Bit-field values for MCCR1. - */ -#define CONFIG_SYS_ROMNAL 0 -#define CONFIG_SYS_ROMFAL 7 - - /* Bit-field values for MCCR2. - */ -#define CONFIG_SYS_REFINT 430 /* Refresh interval */ - - /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. - */ -#define CONFIG_SYS_BSTOPRE 192 - - /* Bit-field values for MCCR3. - */ -#define CONFIG_SYS_REFREC 2 /* Refresh to activate interval */ -#define CONFIG_SYS_RDLAT 3 /* Data latancy from read command */ - - /* Bit-field values for MCCR4. - */ -#define CONFIG_SYS_PRETOACT 2 /* Precharge to activate interval */ -#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */ -#define CONFIG_SYS_SDMODE_CAS_LAT 2 /* SDMODE CAS latancy */ -#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */ -#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length */ -#define CONFIG_SYS_ACTORW 2 -#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1 - -/* Memory bank settings. - * Only bits 20-29 are actually used from these vales to set the - * start/end addresses. The upper two bits will always be 0, and the lower - * 20 bits will be 0x00000 for a start address, or 0xfffff for an end - * address. Refer to the MPC8240 book. - */ - -#define CONFIG_SYS_BANK0_START 0x00000000 -#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1) -#define CONFIG_SYS_BANK0_ENABLE 1 -#define CONFIG_SYS_BANK1_START 0x3ff00000 -#define CONFIG_SYS_BANK1_END 0x3fffffff -#define CONFIG_SYS_BANK1_ENABLE 0 -#define CONFIG_SYS_BANK2_START 0x3ff00000 -#define CONFIG_SYS_BANK2_END 0x3fffffff -#define CONFIG_SYS_BANK2_ENABLE 0 -#define CONFIG_SYS_BANK3_START 0x3ff00000 -#define CONFIG_SYS_BANK3_END 0x3fffffff -#define CONFIG_SYS_BANK3_ENABLE 0 -#define CONFIG_SYS_BANK4_START 0x3ff00000 -#define CONFIG_SYS_BANK4_END 0x3fffffff -#define CONFIG_SYS_BANK4_ENABLE 0 -#define CONFIG_SYS_BANK5_START 0x3ff00000 -#define CONFIG_SYS_BANK5_END 0x3fffffff -#define CONFIG_SYS_BANK5_ENABLE 0 -#define CONFIG_SYS_BANK6_START 0x3ff00000 -#define CONFIG_SYS_BANK6_END 0x3fffffff -#define CONFIG_SYS_BANK6_ENABLE 0 -#define CONFIG_SYS_BANK7_START 0x3ff00000 -#define CONFIG_SYS_BANK7_END 0x3fffffff -#define CONFIG_SYS_BANK7_ENABLE 0 - -#define CONFIG_SYS_ODCR 0xff - -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT3L (0xFC000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U (0xFC000000 | BATU_BL_64M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* Max number of sectors in one bank */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ - - /* Warining: environment is not EMBEDDED in the U-Boot code. - * It's stored in flash separately. - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0xFFF70000 -#define CONFIG_ENV_SIZE 0x4000 /* Size of the Environment */ -#define CONFIG_ENV_OFFSET 0 /* starting right at the beginning */ -#define CONFIG_ENV_SECT_SIZE 0x40000 /* Size of the Environment Sector */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_PNP /* we need Plug 'n Play */ -#define CONFIG_NET_MULTI /* Multi ethernet cards support */ -#define CONFIG_TULIP -#define CONFIG_EEPRO100 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#endif /* __CONFIG_H */ diff --git a/include/configs/sbc8260.h b/include/configs/sbc8260.h deleted file mode 100644 index 0d83337254..0000000000 --- a/include/configs/sbc8260.h +++ /dev/null @@ -1,1080 +0,0 @@ -/* - * (C) Copyright 2000 - * Murray Jensen <Murray.Jensen@cmst.csiro.au> - * - * (C) Copyright 2000 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * (C) Copyright 2001 - * Advent Networks, Inc. <http://www.adventnetworks.com> - * Jay Monkman <jtm@smoothsmoothie.com> - * - * Configuration settings for the WindRiver SBC8260 board. - * See http://www.windriver.com/products/html/sbc8260.html - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_SYS_TEXT_BASE 0x40000000 - -/* Enable debug prints */ -#undef DEBUG_BOOTP_EXT /* Debug received vendor fields */ - -/***************************************************************************** - * - * These settings must match the way _your_ board is set up - * - *****************************************************************************/ - -/* What is the oscillator's (UX2) frequency in Hz? */ -#define CONFIG_8260_CLKIN (66 * 1000 * 1000) - -/*----------------------------------------------------------------------- - * MODCK_H & MODCLK[1-3] - Ref: Section 9.2 in MPC8206 User Manual - *----------------------------------------------------------------------- - * What should MODCK_H be? It is dependent on the oscillator - * frequency, MODCK[1-3], and desired CPM and core frequencies. - * Here are some example values (all frequencies are in MHz): - * - * MODCK_H MODCK[1-3] Osc CPM Core S2-6 S2-7 S2-8 - * ------- ---------- --- --- ---- ----- ----- ----- - * 0x1 0x5 33 100 133 Open Close Open - * 0x1 0x6 33 100 166 Open Open Close - * 0x1 0x7 33 100 200 Open Open Open - * - * 0x2 0x2 33 133 133 Close Open Close - * 0x2 0x3 33 133 166 Close Open Open - * 0x2 0x4 33 133 200 Open Close Close - * 0x2 0x5 33 133 233 Open Close Open - * 0x2 0x6 33 133 266 Open Open Close - * - * 0x5 0x5 66 133 133 Open Close Open - * 0x5 0x6 66 133 166 Open Open Close - * 0x5 0x7 66 133 200 Open Open Open - * 0x6 0x0 66 133 233 Close Close Close - * 0x6 0x1 66 133 266 Close Close Open - * 0x6 0x2 66 133 300 Close Open Close - */ -#define CONFIG_SYS_SBC_MODCK_H 0x05 - -/* Define this if you want to boot from 0x00000100. If you don't define - * this, you will need to program the bootloader to 0xfff00000, and - * get the hardware reset config words at 0xfe000000. The simplest - * way to do that is to program the bootloader at both addresses. - * It is suggested that you just let U-Boot live at 0x00000000. - */ -#define CONFIG_SYS_SBC_BOOT_LOW 1 - -/* What should the base address of the main FLASH be and how big is - * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/sbc8260/config.mk - * The main FLASH is whichever is connected to *CS0. U-Boot expects - * this to be the SIMM. - */ -#define CONFIG_SYS_FLASH0_BASE 0x40000000 -#define CONFIG_SYS_FLASH0_SIZE 4 - -/* What should the base address of the secondary FLASH be and how big - * is it (in Mbytes)? The secondary FLASH is whichever is connected - * to *CS6. U-Boot expects this to be the on board FLASH. If you don't - * want it enabled, don't define these constants. - */ -#define CONFIG_SYS_FLASH1_BASE 0x60000000 -#define CONFIG_SYS_FLASH1_SIZE 2 - -/* What should be the base address of SDRAM DIMM and how big is - * it (in Mbytes)? -*/ -#define CONFIG_SYS_SDRAM0_BASE 0x00000000 -#define CONFIG_SYS_SDRAM0_SIZE 64 - -/* What should be the base address of the LEDs and switch S0? - * If you don't want them enabled, don't define this. - */ -#define CONFIG_SYS_LED_BASE 0xa0000000 - - -/* - * SBC8260 with 16 MB DIMM: - * - * 0x0000 0000 Exception Vector code, 8k - * : - * 0x0000 1FFF - * 0x0000 2000 Free for Application Use - * : - * : - * - * : - * : - * 0x00F5 FF30 Monitor Stack (Growing downward) - * Monitor Stack Buffer (0x80) - * 0x00F5 FFB0 Board Info Data - * 0x00F6 0000 Malloc Arena - * : CONFIG_ENV_SECT_SIZE, 256k - * : CONFIG_SYS_MALLOC_LEN, 128k - * 0x00FC 0000 RAM Copy of Monitor Code - * : CONFIG_SYS_MONITOR_LEN, 256k - * 0x00FF FFFF [End of RAM], CONFIG_SYS_SDRAM_SIZE - 1 - */ - -/* - * SBC8260 with 64 MB DIMM: - * - * 0x0000 0000 Exception Vector code, 8k - * : - * 0x0000 1FFF - * 0x0000 2000 Free for Application Use - * : - * : - * - * : - * : - * 0x03F5 FF30 Monitor Stack (Growing downward) - * Monitor Stack Buffer (0x80) - * 0x03F5 FFB0 Board Info Data - * 0x03F6 0000 Malloc Arena - * : CONFIG_ENV_SECT_SIZE, 256k - * : CONFIG_SYS_MALLOC_LEN, 128k - * 0x03FC 0000 RAM Copy of Monitor Code - * : CONFIG_SYS_MONITOR_LEN, 256k - * 0x03FF FFFF [End of RAM], CONFIG_SYS_SDRAM_SIZE - 1 - */ - - -/* - * select serial console configuration - * - * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - * - * if CONFIG_CONS_NONE is defined, then the serial console routines must - * defined elsewhere. - */ -#define CONFIG_CONS_ON_SMC 1 /* define if console on SMC */ -#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on neither */ -#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */ - -/* - * select ethernet configuration - * - * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then - * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 - * for FCC) - * - * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be - * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. - */ - -#undef CONFIG_ETHER_ON_SCC -#define CONFIG_ETHER_ON_FCC -#undef CONFIG_ETHER_NONE /* define if ethernet on neither */ - -#ifdef CONFIG_ETHER_ON_SCC -#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */ -#endif /* CONFIG_ETHER_ON_SCC */ - -#ifdef CONFIG_ETHER_ON_FCC -#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */ -#undef CONFIG_ETHER_LOOPBACK_TEST /* Ethernet external loopback test */ -#define CONFIG_MII /* MII PHY management */ -#define CONFIG_BITBANGMII /* bit-bang MII PHY management */ -/* - * Port pins used for bit-banged MII communictions (if applicable). - */ -#define MDIO_PORT 2 /* Port C */ -#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \ - (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT ) -#define MDC_DECLARE MDIO_DECLARE - -#define MDIO_ACTIVE (iop->pdir |= 0x00400000) -#define MDIO_TRISTATE (iop->pdir &= ~0x00400000) -#define MDIO_READ ((iop->pdat & 0x00400000) != 0) - -#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ - else iop->pdat &= ~0x00400000 - -#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ - else iop->pdat &= ~0x00200000 - -#define MIIDELAY udelay(1) -#endif /* CONFIG_ETHER_ON_FCC */ - -#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1) - -/* - * - RX clk is CLK11 - * - TX clk is CLK12 - */ -# define CONFIG_SYS_CMXSCR_VALUE (CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12) - -#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) - -/* - * - Rx-CLK is CLK13 - * - Tx-CLK is CLK14 - * - Select bus for bd/buffers (see 28-13) - * - Enable Full Duplex in FSMR - */ -# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK) -# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14) -# define CONFIG_SYS_CPMFCR_RAMTYPE 0 -# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) - -#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */ - -/* - * Select SPI support configuration - */ -#undef CONFIG_SPI /* Disable SPI driver */ - -/* - * Select i2c support configuration - * - * Supported configurations are {none, software, hardware} drivers. - * If the software driver is chosen, there are some additional - * configuration items that the driver uses to drive the port pins. - */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * Software (bit-bang) I2C driver configuration - */ -#ifdef CONFIG_SOFT_I2C -#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ -#define I2C_ACTIVE (iop->pdir |= 0x00010000) -#define I2C_TRISTATE (iop->pdir &= ~0x00010000) -#define I2C_READ ((iop->pdat & 0x00010000) != 0) -#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ - else iop->pdat &= ~0x00010000 -#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ - else iop->pdat &= ~0x00020000 -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ - - -/* Define this to reserve an entire FLASH sector (256 KB) for - * environment variables. Otherwise, the environment will be - * put in the same sector as U-Boot, and changing variables - * will erase U-Boot temporarily - */ -#define CONFIG_ENV_IN_OWN_SECT 1 - -/* Define to allow the user to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* What should the console's baud rate be? */ -#define CONFIG_BAUDRATE 9600 - -/* Ethernet MAC address - * Note: We are using the EST Corporation OUI (00:a0:1e:xx:xx:xx) - * http://standards.ieee.org/regauth/oui/index.shtml - */ -#define CONFIG_ETHADDR 00:a0:1e:a8:7b:cb - -/* - * Define this to set the last octet of the ethernet address from the - * DS0-DS7 switch and light the LEDs with the result. The DS0-DS7 - * switch and the LEDs are backwards with respect to each other. DS7 - * is on the board edge side of both the LED strip and the DS0-DS7 - * switch. - */ -#undef CONFIG_MISC_INIT_R - -/* Set to a positive value to delay for running BOOTCOMMAND */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -/* Be selective on what keys can delay or stop the autoboot process - * To stop use: " " - */ -#undef CONFIG_AUTOBOOT_KEYED -#ifdef CONFIG_AUTOBOOT_KEYED -# define CONFIG_AUTOBOOT_PROMPT \ - "Autobooting in %d seconds, press \" \" to stop\n", bootdelay -# define CONFIG_AUTOBOOT_STOP_STR " " -# undef CONFIG_AUTOBOOT_DELAY_STR -# define DEBUG_BOOTKEYS 0 -#endif - -/* Define this to contain any number of null terminated strings that - * will be part of the default enviroment compiled into the boot image. - * - * Variable Usage - * -------------- ------------------------------------------------------- - * serverip server IP address - * ipaddr my IP address - * reprog Reload flash with a new copy of U-Boot - * zapenv Erase the environment area in flash - * root-on-initrd Set the bootcmd variable to allow booting of an initial - * ram disk. - * root-on-nfs Set the bootcmd variable to allow booting of a NFS - * mounted root filesystem. - * boot-hook Convenient stub to do something useful before the - * bootm command is executed. - * - * Example usage of root-on-initrd and root-on-nfs : - * - * Note: The lines have been wrapped to improved its readability. - * - * => printenv bootcmd - * bootcmd=version;echo;bootp;setenv bootargs root=/dev/nfs rw - * nfsroot=${serverip}:${rootpath} - * ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;run boot-hook;bootm - * - * => run root-on-initrd - * => printenv bootcmd - * bootcmd=version;echo;bootp;setenv bootargs root=/dev/ram0 rw - * ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;run boot-hook;bootm - * - * => run root-on-nfs - * => printenv bootcmd - * bootcmd=version;echo;bootp;setenv bootargs root=/dev/nfs rw - * nfsroot=${serverip}:${rootpath} - * ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;run boot-hook;bootm - * - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - "serverip=192.168.123.205\0" \ - "ipaddr=192.168.123.213\0" \ - "reprog="\ - "bootp;" \ - "tftpboot 0x140000 /bdi2000/u-boot.bin;" \ - "protect off 1:0;" \ - "erase 1:0;" \ - "cp.b 140000 40000000 ${filesize};" \ - "protect on 1:0\0" \ - "zapenv="\ - "protect off 1:1;" \ - "erase 1:1;" \ - "protect on 1:1\0" \ - "root-on-initrd="\ - "setenv bootcmd "\ - "version;" \ - "echo;" \ - "bootp;" \ - "setenv bootargs root=/dev/ram0 rw " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ - "run boot-hook;" \ - "bootm\0" \ - "root-on-nfs="\ - "setenv bootcmd "\ - "version;" \ - "echo;" \ - "bootp;" \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ - "run boot-hook;" \ - "bootm\0" \ - "boot-hook=echo\0" - -/* Define a command string that is automatically executed when no character - * is read on the console interface withing "Boot Delay" after reset. - */ -#undef CONFIG_BOOT_ROOT_INITRD /* Use ram disk for the root file system */ -#define CONFIG_BOOT_ROOT_NFS /* Use a NFS mounted root file system */ - -#ifdef CONFIG_BOOT_ROOT_INITRD -#define CONFIG_BOOTCOMMAND \ - "version;" \ - "echo;" \ - "bootp;" \ - "setenv bootargs root=/dev/ram0 rw " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ - "bootm" -#endif /* CONFIG_BOOT_ROOT_INITRD */ - -#ifdef CONFIG_BOOT_ROOT_NFS -#define CONFIG_BOOTCOMMAND \ - "version;" \ - "echo;" \ - "bootp;" \ - "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ - "bootm" -#endif /* CONFIG_BOOT_ROOT_NFS */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_DNS -#define CONFIG_BOOTP_DNS2 -#define CONFIG_BOOTP_SEND_HOSTNAME - - -/* undef this to save memory */ -#define CONFIG_SYS_LONGHELP - -/* Monitor Command Prompt */ -#define CONFIG_SYS_PROMPT "=> " - -#undef CONFIG_SYS_HUSH_PARSER -#ifdef CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#endif - -/* When CONFIG_TIMESTAMP is selected, the timestamp (date and time) - * of an image is printed by image commands like bootm or iminfo. - */ -#define CONFIG_TIMESTAMP - -/* If this variable is defined, an environment variable named "ver" - * is created by U-Boot showing the U-Boot version. - */ -#define CONFIG_VERSION_VARIABLE - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SDRAM - -#undef CONFIG_CMD_KGDB - -#if defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_CMD_CMD_MII -#endif - - -#undef CONFIG_WATCHDOG /* disable the watchdog */ - -/* Where do the internal registers live? */ -#define CONFIG_SYS_IMMR 0xF0000000 - -/***************************************************************************** - * - * You should not have to modify any of the following settings - * - *****************************************************************************/ - -#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ -#define CONFIG_SBC8260 1 /* on an EST SBC8260 Board */ -#define CONFIG_CPM2 1 /* Has a CPM2 */ - - -/* - * Miscellaneous configurable options - */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16) - -#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ - -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_SYS_ALT_MEMTEST /* Select full-featured memory test */ -#define CONFIG_SYS_MEMTEST_START 0x2000 /* memtest works from the end of */ - /* the exception vector table */ - /* to the end of the DRAM */ - /* less monitor and malloc area */ -#define CONFIG_SYS_STACK_USAGE 0x10000 /* Reserve 64k for the stack usage */ -#define CONFIG_SYS_MEM_END_USAGE ( CONFIG_SYS_MONITOR_LEN \ - + CONFIG_SYS_MALLOC_LEN \ - + CONFIG_ENV_SECT_SIZE \ - + CONFIG_SYS_STACK_USAGE ) - -#define CONFIG_SYS_MEMTEST_END ( CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 \ - - CONFIG_SYS_MEM_END_USAGE ) - -/* valid baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE -#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE -#define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_SDRAM0_SIZE - -/*----------------------------------------------------------------------- - * Hard Reset Configuration Words - */ -#if defined(CONFIG_SYS_SBC_BOOT_LOW) -# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) -#else -# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0) -#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */ - -/* get the HRCW ISB field from CONFIG_SYS_IMMR */ -#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) | \ - ((CONFIG_SYS_IMMR & 0x01000000) >> 7) | \ - ((CONFIG_SYS_IMMR & 0x00100000) >> 4) ) - -#define CONFIG_SYS_HRCW_MASTER ( HRCW_BPS11 | \ - HRCW_DPPC11 | \ - CONFIG_SYS_SBC_HRCW_IMMR | \ - HRCW_MMR00 | \ - HRCW_LBPC11 | \ - HRCW_APPC10 | \ - HRCW_CS10PC00 | \ - (CONFIG_SYS_SBC_MODCK_H & HRCW_MODCK_H1111) | \ - CONFIG_SYS_SBC_HRCW_BOOT_FLAGS ) - -/* no slaves */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent. - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH0_BASE - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 16 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ - -#ifndef CONFIG_SYS_RAMBOOT -# define CONFIG_ENV_IS_IN_FLASH 1 - -# ifdef CONFIG_ENV_IN_OWN_SECT -# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) -# define CONFIG_ENV_SECT_SIZE 0x40000 -# else -# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE) -# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ -# define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */ -# endif /* CONFIG_ENV_IN_OWN_SECT */ - -#else -# define CONFIG_ENV_IS_IN_NVRAM 1 -# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -# define CONFIG_ENV_SIZE 0x200 -#endif /* CONFIG_SYS_RAMBOOT */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * HIDx - Hardware Implementation-dependent Registers 2-11 - *----------------------------------------------------------------------- - * HID0 also contains cache control - initially enable both caches and - * invalidate contents, then the final state leaves only the instruction - * cache enabled. Note that Power-On and Hard reset invalidate the caches, - * but Soft reset does not. - * - * HID1 has only read-only information - nothing to set. - */ -#define CONFIG_SYS_HID0_INIT (HID0_ICE |\ - HID0_DCE |\ - HID0_ICFI |\ - HID0_DCI |\ - HID0_IFEM |\ - HID0_ABE) - -#define CONFIG_SYS_HID0_FINAL (HID0_ICE |\ - HID0_IFEM |\ - HID0_ABE |\ - HID0_EMCP) -#define CONFIG_SYS_HID2 0 - -/*----------------------------------------------------------------------- - * RMR - Reset Mode Register - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RMR 0 - -/*----------------------------------------------------------------------- - * BCR - Bus Configuration 4-25 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_BCR (BCR_ETM) - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 4-31 - *----------------------------------------------------------------------- - */ - -#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC11 |\ - SIUMCR_L2CPC00 |\ - SIUMCR_APPC10 |\ - SIUMCR_MMR00) - - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\ - SYPCR_BMT |\ - SYPCR_PBME |\ - SYPCR_LBME |\ - SYPCR_SWRI |\ - SYPCR_SWP |\ - SYPCR_SWE) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\ - SYPCR_BMT |\ - SYPCR_PBME |\ - SYPCR_LBME |\ - SYPCR_SWRI |\ - SYPCR_SWP) -#endif /* CONFIG_WATCHDOG */ - -/*----------------------------------------------------------------------- - * TMCNTSC - Time Counter Status and Control 4-40 - *----------------------------------------------------------------------- - * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, - * and enable Time Counter - */ -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\ - TMCNTSC_ALR |\ - TMCNTSC_TCF |\ - TMCNTSC_TCE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 4-42 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable - * Periodic timer - */ -#define CONFIG_SYS_PISCR (PISCR_PS |\ - PISCR_PTF |\ - PISCR_PTE) - -/*----------------------------------------------------------------------- - * SCCR - System Clock Control 9-8 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_SCCR 0 - -/*----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration 13-7 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RCCR 0 - -/* - * Initialize Memory Controller: - * - * Bank Bus Machine PortSz Device - * ---- --- ------- ------ ------ - * 0 60x GPCM 32 bit FLASH (SIMM - 4MB) * - * 1 60x GPCM 32 bit FLASH (SIMM - Unused) - * 2 60x SDRAM 64 bit SDRAM (DIMM - 16MB or 64MB) - * 3 60x SDRAM 64 bit SDRAM (DIMM - Unused) - * 4 Local SDRAM 32 bit SDRAM (on board - 4MB) - * 5 60x GPCM 8 bit EEPROM (8KB) - * 6 60x GPCM 8 bit FLASH (on board - 2MB) * - * 7 60x GPCM 8 bit LEDs, switches - * - * (*) This configuration requires the SBC8260 be configured - * so that *CS0 goes to the FLASH SIMM, and *CS6 goes to - * the on board FLASH. In other words, JP24 should have - * pins 1 and 2 jumpered and pins 3 and 4 jumpered. - * - */ - -/*----------------------------------------------------------------------- - * BR0,BR1 - Base Register - * Ref: Section 10.3.1 on page 10-14 - * OR0,OR1 - Option Register - * Ref: Section 10.3.2 on page 10-18 - *----------------------------------------------------------------------- - */ - -/* Bank 0,1 - FLASH SIMM - * - * This expects the FLASH SIMM to be connected to *CS0 - * It consists of 4 AM29F080B parts. - * - * Note: For the 4 MB SIMM, *CS1 is unused. - */ - -/* BR0 is configured as follows: - * - * - Base address of 0x40000000 - * - 32 bit port size - * - Data errors checking is disabled - * - Read and write access - * - GPCM 60x bus - * - Access are handled by the memory controller according to MSEL - * - Not used for atomic operations - * - No data pipelining is done - * - Valid - */ -#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\ - BRx_PS_32 |\ - BRx_MS_GPCM_P |\ - BRx_V) - -/* OR0 is configured as follows: - * - * - 4 MB - * - *BCTL0 is asserted upon access to the current memory bank - * - *CW / *WE are negated a quarter of a clock earlier - * - *CS is output at the same time as the address lines - * - Uses a clock cycle length of 5 - * - *PSDVAL is generated internally by the memory controller - * unless *GTA is asserted earlier externally. - * - Relaxed timing is generated by the GPCM for accesses - * initiated to this memory region. - * - One idle clock is inserted between a read access from the - * current bank and the next access. - */ -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\ - ORxG_CSNT |\ - ORxG_ACS_DIV1 |\ - ORxG_SCY_5_CLK |\ - ORxG_TRLX |\ - ORxG_EHTR) - -/*----------------------------------------------------------------------- - * BR2,BR3 - Base Register - * Ref: Section 10.3.1 on page 10-14 - * OR2,OR3 - Option Register - * Ref: Section 10.3.2 on page 10-16 - *----------------------------------------------------------------------- - */ - -/* Bank 2,3 - SDRAM DIMM - * - * 16MB DIMM: P/N - * 64MB DIMM: P/N 1W-8864X8-4-P1-EST - * - * Note: *CS3 is unused for this DIMM - */ - -/* With a 16 MB or 64 MB DIMM, the BR2 is configured as follows: - * - * - Base address of 0x00000000 - * - 64 bit port size (60x bus only) - * - Data errors checking is disabled - * - Read and write access - * - SDRAM 60x bus - * - Access are handled by the memory controller according to MSEL - * - Not used for atomic operations - * - No data pipelining is done - * - Valid - */ -#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_MS_SDRAM_P |\ - BRx_V) - -#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_MS_SDRAM_P |\ - BRx_V) - -/* With a 16 MB DIMM, the OR2 is configured as follows: - * - * - 16 MB - * - 2 internal banks per device - * - Row start address bit is A9 with PSDMR[PBI] = 0 - * - 11 row address lines - * - Back-to-back page mode - * - Internal bank interleaving within save device enabled - */ -#if (CONFIG_SYS_SDRAM0_SIZE == 16) -#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\ - ORxS_BPD_2 |\ - ORxS_ROWST_PBI0_A9 |\ - ORxS_NUMR_11) -#endif - -/* With a 64 MB DIMM, the OR2 is configured as follows: - * - * - 64 MB - * - 4 internal banks per device - * - Row start address bit is A8 with PSDMR[PBI] = 0 - * - 12 row address lines - * - Back-to-back page mode - * - Internal bank interleaving within save device enabled - */ -#if (CONFIG_SYS_SDRAM0_SIZE == 64) -#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI0_A8 |\ - ORxS_NUMR_12) -#endif - -/*----------------------------------------------------------------------- - * PSDMR - 60x Bus SDRAM Mode Register - * Ref: Section 10.3.3 on page 10-21 - *----------------------------------------------------------------------- - */ - -/* Address that the DIMM SPD memory lives at. - */ -#define SDRAM_SPD_ADDR 0x54 - -#if (CONFIG_SYS_SDRAM0_SIZE == 16) -/* With a 16 MB DIMM, the PSDMR is configured as follows: - * - * - Bank Based Interleaving, - * - Refresh Enable, - * - Address Multiplexing where A5 is output on A14 pin - * (A6 on A15, and so on), - * - use address pins A16-A18 as bank select, - * - A9 is output on SDA10 during an ACTIVATE command, - * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks, - * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command - * is 3 clocks, - * - earliest timing for READ/WRITE command after ACTIVATE command is - * 2 clocks, - * - earliest timing for PRECHARGE after last data was read is 1 clock, - * - earliest timing for PRECHARGE after last data was written is 1 clock, - * - CAS Latency is 2. - */ -#define CONFIG_SYS_PSDMR (PSDMR_RFEN |\ - PSDMR_SDAM_A14_IS_A5 |\ - PSDMR_BSMA_A16_A18 |\ - PSDMR_SDA10_PBI0_A9 |\ - PSDMR_RFRC_7_CLK |\ - PSDMR_PRETOACT_3W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_1C |\ - PSDMR_CL_2) -#endif - -#if (CONFIG_SYS_SDRAM0_SIZE == 64) -/* With a 64 MB DIMM, the PSDMR is configured as follows: - * - * - Bank Based Interleaving, - * - Refresh Enable, - * - Address Multiplexing where A5 is output on A14 pin - * (A6 on A15, and so on), - * - use address pins A14-A16 as bank select, - * - A9 is output on SDA10 during an ACTIVATE command, - * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks, - * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command - * is 3 clocks, - * - earliest timing for READ/WRITE command after ACTIVATE command is - * 2 clocks, - * - earliest timing for PRECHARGE after last data was read is 1 clock, - * - earliest timing for PRECHARGE after last data was written is 1 clock, - * - CAS Latency is 2. - */ -#define CONFIG_SYS_PSDMR (PSDMR_RFEN |\ - PSDMR_SDAM_A14_IS_A5 |\ - PSDMR_BSMA_A14_A16 |\ - PSDMR_SDA10_PBI0_A9 |\ - PSDMR_RFRC_7_CLK |\ - PSDMR_PRETOACT_3W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_1C |\ - PSDMR_CL_2) -#endif - -/* - * Shoot for approximately 1MHz on the prescaler. - */ -#if (CONFIG_8260_CLKIN == (66 * 1000 * 1000)) -#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV64 -#elif (CONFIG_8260_CLKIN == (33 * 1000 * 1000)) -#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV32 -#else -#warning "Unconfigured bus clock freq: check CONFIG_SYS_MPTPR and CONFIG_SYS_PSRT are OK" -#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV32 -#endif -#define CONFIG_SYS_PSRT 14 - - -/* Bank 4 - On board SDRAM - * - * This is not implemented yet. - */ - -/*----------------------------------------------------------------------- - * BR6 - Base Register - * Ref: Section 10.3.1 on page 10-14 - * OR6 - Option Register - * Ref: Section 10.3.2 on page 10-18 - *----------------------------------------------------------------------- - */ - -/* Bank 6 - On board FLASH - * - * This expects the on board FLASH SIMM to be connected to *CS6 - * It consists of 1 AM29F016A part. - */ -#if (defined(CONFIG_SYS_FLASH1_BASE) && defined(CONFIG_SYS_FLASH1_SIZE)) - -/* BR6 is configured as follows: - * - * - Base address of 0x60000000 - * - 8 bit port size - * - Data errors checking is disabled - * - Read and write access - * - GPCM 60x bus - * - Access are handled by the memory controller according to MSEL - * - Not used for atomic operations - * - No data pipelining is done - * - Valid - */ -# define CONFIG_SYS_BR6_PRELIM ((CONFIG_SYS_FLASH1_BASE & BRx_BA_MSK) |\ - BRx_PS_8 |\ - BRx_MS_GPCM_P |\ - BRx_V) - -/* OR6 is configured as follows: - * - * - 2 MB - * - *BCTL0 is asserted upon access to the current memory bank - * - *CW / *WE are negated a quarter of a clock earlier - * - *CS is output at the same time as the address lines - * - Uses a clock cycle length of 5 - * - *PSDVAL is generated internally by the memory controller - * unless *GTA is asserted earlier externally. - * - Relaxed timing is generated by the GPCM for accesses - * initiated to this memory region. - * - One idle clock is inserted between a read access from the - * current bank and the next access. - */ -# define CONFIG_SYS_OR6_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH1_SIZE) |\ - ORxG_CSNT |\ - ORxG_ACS_DIV1 |\ - ORxG_SCY_5_CLK |\ - ORxG_TRLX |\ - ORxG_EHTR) -#endif /* (defined(CONFIG_SYS_FLASH1_BASE) && defined(CONFIG_SYS_FLASH1_SIZE)) */ - -/*----------------------------------------------------------------------- - * BR7 - Base Register - * Ref: Section 10.3.1 on page 10-14 - * OR7 - Option Register - * Ref: Section 10.3.2 on page 10-18 - *----------------------------------------------------------------------- - */ - -/* Bank 7 - LEDs and switches - * - * LEDs are at 0x00001 (write only) - * switches are at 0x00001 (read only) - */ -#ifdef CONFIG_SYS_LED_BASE - -/* BR7 is configured as follows: - * - * - Base address of 0xA0000000 - * - 8 bit port size - * - Data errors checking is disabled - * - Read and write access - * - GPCM 60x bus - * - Access are handled by the memory controller according to MSEL - * - Not used for atomic operations - * - No data pipelining is done - * - Valid - */ -# define CONFIG_SYS_BR7_PRELIM ((CONFIG_SYS_LED_BASE & BRx_BA_MSK) |\ - BRx_PS_8 |\ - BRx_MS_GPCM_P |\ - BRx_V) - -/* OR7 is configured as follows: - * - * - 1 byte - * - *BCTL0 is asserted upon access to the current memory bank - * - *CW / *WE are negated a quarter of a clock earlier - * - *CS is output at the same time as the address lines - * - Uses a clock cycle length of 15 - * - *PSDVAL is generated internally by the memory controller - * unless *GTA is asserted earlier externally. - * - Relaxed timing is generated by the GPCM for accesses - * initiated to this memory region. - * - One idle clock is inserted between a read access from the - * current bank and the next access. - */ -# define CONFIG_SYS_OR7_PRELIM (ORxG_AM_MSK |\ - ORxG_CSNT |\ - ORxG_ACS_DIV1 |\ - ORxG_SCY_15_CLK |\ - ORxG_TRLX |\ - ORxG_EHTR) -#endif /* CONFIG_SYS_LED_BASE */ -#endif /* __CONFIG_H */ diff --git a/include/configs/vision2.h b/include/configs/vision2.h index b5c73571b3..d95c0ba444 100644 --- a/include/configs/vision2.h +++ b/include/configs/vision2.h @@ -41,6 +41,8 @@ #define CONFIG_INITRD_TAG #define BOARD_LATE_INIT +#define CONFIG_MACH_TYPE MACH_TYPE_TTC_VISION2 + /* * Size of malloc() pool */ diff --git a/include/configs/zmx25.h b/include/configs/zmx25.h index 374c88a0f4..ab7f30f1e8 100644 --- a/include/configs/zmx25.h +++ b/include/configs/zmx25.h @@ -32,6 +32,7 @@ #define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_TEXT_BASE 0xA0000000 +#define CONFIG_MACH_TYPE MACH_TYPE_ZMX25 /* * Environment settings */ diff --git a/include/fat.h b/include/fat.h index afb2116e8e..15dbf1094c 100644 --- a/include/fat.h +++ b/include/fat.h @@ -33,22 +33,15 @@ /* Maximum Long File Name length supported here is 128 UTF-16 code units */ #define VFAT_MAXLEN_BYTES 256 /* Maximum LFN buffer in bytes */ #define VFAT_MAXSEQ 9 /* Up to 9 of 13 2-byte UTF-16 entries */ -#define LINEAR_PREFETCH_SIZE (SECTOR_SIZE*2) /* Prefetch buffer size */ - -#define SECTOR_SIZE FS_BLOCK_SIZE - -#define FS_BLOCK_SIZE 512 - -#if FS_BLOCK_SIZE != SECTOR_SIZE -#error FS_BLOCK_SIZE != SECTOR_SIZE - This code needs to be fixed! -#endif +#define PREFETCH_BLOCKS 2 #define MAX_CLUSTSIZE 65536 -#define DIRENTSPERBLOCK (FS_BLOCK_SIZE/sizeof(dir_entry)) -#define DIRENTSPERCLUST ((mydata->clust_size*SECTOR_SIZE)/sizeof(dir_entry)) +#define DIRENTSPERBLOCK (mydata->sect_size / sizeof(dir_entry)) +#define DIRENTSPERCLUST ((mydata->clust_size * mydata->sect_size) / \ + sizeof(dir_entry)) #define FATBUFBLOCKS 6 -#define FATBUFSIZE (FS_BLOCK_SIZE*FATBUFBLOCKS) +#define FATBUFSIZE (mydata->sect_size * FATBUFBLOCKS) #define FAT12BUFSIZE ((FATBUFSIZE*2)/3) #define FAT16BUFSIZE (FATBUFSIZE/2) #define FAT32BUFSIZE (FATBUFSIZE/4) @@ -181,11 +174,12 @@ typedef struct dir_slot { * (see FAT32 accesses) */ typedef struct { - __u8 fatbuf[FATBUFSIZE]; /* Current FAT buffer */ + __u8 *fatbuf; /* Current FAT buffer */ int fatsize; /* Size of FAT in bits */ __u16 fatlength; /* Length of FAT in sectors */ __u16 fat_sect; /* Starting sector of the FAT */ __u16 rootdir_sect; /* Start sector of root directory */ + __u16 sect_size; /* Size of sectors in bytes */ __u16 clust_size; /* Size of clusters in sectors */ short data_begin; /* The sector of the first cluster, can be negative */ int fatbufnum; /* Used by get_fatent, init to -1 */ diff --git a/include/linux/compiler-gcc3.h b/include/linux/compiler-gcc3.h new file mode 100644 index 0000000000..2befe6513c --- /dev/null +++ b/include/linux/compiler-gcc3.h @@ -0,0 +1,21 @@ +#ifndef __LINUX_COMPILER_H +#error "Please don't include <linux/compiler-gcc3.h> directly, include <linux/compiler.h> instead." +#endif + +#if __GNUC_MINOR__ >= 3 +# define __used __attribute__((__used__)) +#else +# define __used __attribute__((__unused__)) +#endif + +#if __GNUC_MINOR__ >= 4 +#define __must_check __attribute__((warn_unused_result)) +#endif + +/* + * A trick to suppress uninitialized variable warning without generating any + * code + */ +#define uninitialized_var(x) x = x + +#define __always_inline inline __attribute__((always_inline)) diff --git a/include/nand.h b/include/nand.h index 8d94b5cbd7..b4140794c5 100644 --- a/include/nand.h +++ b/include/nand.h @@ -132,6 +132,12 @@ int nand_lock( nand_info_t *meminfo, int tight ); int nand_unlock( nand_info_t *meminfo, ulong start, ulong length ); int nand_get_lock_status(nand_info_t *meminfo, loff_t offset); +int nand_spl_load_image(uint32_t offs, unsigned int size, void *dst); +void nand_deselect(void); + +void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len); +void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len); + #ifdef CONFIG_SYS_NAND_SELECT_DEVICE void board_nand_select_device(struct nand_chip *nand, int chip); #endif diff --git a/include/netdev.h b/include/netdev.h index 96c7b9b5f2..480453e51d 100644 --- a/include/netdev.h +++ b/include/netdev.h @@ -61,8 +61,8 @@ int ep93xx_eth_initialize(u8 dev_num, int base_addr); int eth_3com_initialize (bd_t * bis); int ethoc_initialize(u8 dev_num, int base_addr); int fec_initialize (bd_t *bis); -int fecmxc_initialize (bd_t *bis); int fecmxc_initialize(bd_t *bis); +int fecmxc_initialize_multi(bd_t *bis, int dev_id, int phy_id, uint32_t addr); int ftgmac100_initialize(bd_t *bits); int ftmac100_initialize(bd_t *bits); int greth_initialize(bd_t *bis); @@ -94,6 +94,7 @@ int smc911x_initialize(u8 dev_num, int base_addr); int tsi108_eth_initialize(bd_t *bis); int uec_standard_init(bd_t *bis); int uli526x_initialize(bd_t *bis); +int armada100_fec_register(unsigned long base_addr); int xilinx_emaclite_initialize (bd_t *bis, int base_addr); /* Boards with PCI network controllers can call this from their board_eth_init() @@ -185,4 +186,9 @@ struct mv88e61xx_config { int mv88e61xx_switch_initialize(struct mv88e61xx_config *swconfig); #endif /* CONFIG_MV88E61XX_SWITCH */ +/* + * Allow FEC to fine-tune MII configuration on boards which require this. + */ +int fecmxc_register_mii_postcall(struct eth_device *dev, int (*cb)(int)); + #endif /* _NETDEV_H_ */ diff --git a/include/ns16550.h b/include/ns16550.h index 9ea81e9463..51f1c17b31 100644 --- a/include/ns16550.h +++ b/include/ns16550.h @@ -21,8 +21,12 @@ * will not allocate storage for arrays of size 0 */ +#include <linux/types.h> + #if !defined(CONFIG_SYS_NS16550_REG_SIZE) || (CONFIG_SYS_NS16550_REG_SIZE == 0) #error "Please define NS16550 registers size." +#elif defined(CONFIG_SYS_NS16550_MEM32) +#define UART_REG(x) u32 x #elif (CONFIG_SYS_NS16550_REG_SIZE > 0) #define UART_REG(x) \ unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \ diff --git a/include/status_led.h b/include/status_led.h index 59143296c3..c85c206772 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -308,9 +308,6 @@ void status_led_set (int led, int state); /***** STx XTc ********************************************************/ #elif defined(CONFIG_STXXTC) /* XXX empty just to avoid the error */ -/***** sbc8240 ********************************************************/ -#elif defined(CONFIG_WRSBC8240) -/* XXX empty just to avoid the error */ /************************************************************************/ #elif defined(CONFIG_NIOS2) /* XXX empty just to avoid the error */ diff --git a/include/twl6030.h b/include/twl6030.h index 6ed68a0e14..a9fcadbfef 100644 --- a/include/twl6030.h +++ b/include/twl6030.h @@ -33,6 +33,8 @@ #define TWL6030_CHIP_PWM 0x49 /* Slave Address 0x48 */ +#define VMMC_CFG_STATE 0x9A +#define VMMC_CFG_VOLTATE 0x9B #define VUSB_CFG_STATE 0xA2 #define MISC1 0xE4 @@ -130,3 +132,4 @@ void twl6030_start_usb_charging(void); void twl6030_stop_usb_charging(void); int twl6030_get_battery_voltage(void); int twl6030_get_battery_current(void); +void twl6030_power_mmc_init(void); |
