diff options
Diffstat (limited to 'include/configs/sbc8641d.h')
| -rw-r--r-- | include/configs/sbc8641d.h | 24 |
1 files changed, 12 insertions, 12 deletions
diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h index 20da73e0fa..3cd9ff80f6 100644 --- a/include/configs/sbc8641d.h +++ b/include/configs/sbc8641d.h @@ -55,13 +55,13 @@ #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ -#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup*/ #undef CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef #define CONFIG_NUM_DDR_CONTROLLERS 2 @@ -94,7 +94,7 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */ #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ @@ -219,7 +219,7 @@ #undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CFG_FLASH_CFI_DRIVER #define CFG_FLASH_CFI @@ -236,14 +236,14 @@ #else #define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ #endif -#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ +#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 @@ -323,7 +323,7 @@ #undef CFG_SCSI_SCAN_BUS_REVERSE #define CONFIG_NET_MULTI -#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ #undef CONFIG_EEPRO100 #undef CONFIG_TULIP @@ -331,7 +331,7 @@ #if !defined(CONFIG_PCI_PNP) #define PCI_ENET0_IOADDR 0xe0000000 #define PCI_ENET0_MEMADDR 0xe0000000 - #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ + #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ #endif #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ @@ -343,7 +343,7 @@ #define CONFIG_SATA_ULI5288 #define CFG_SCSI_MAX_SCSI_ID 4 #define CFG_SCSI_MAX_LUN 1 -#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN) +#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN) #define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE #endif @@ -352,7 +352,7 @@ #if defined(CONFIG_TSEC_ENET) #ifndef CONFIG_NET_MULTI -#define CONFIG_NET_MULTI 1 +#define CONFIG_NET_MULTI 1 #endif /* #define CONFIG_MII 1 */ /* MII PHY management */ |
