diff options
Diffstat (limited to 'include/configs/qong.h')
| -rw-r--r-- | include/configs/qong.h | 53 |
1 files changed, 34 insertions, 19 deletions
diff --git a/include/configs/qong.h b/include/configs/qong.h index 7f284efe54..426d90d7de 100644 --- a/include/configs/qong.h +++ b/include/configs/qong.h @@ -66,8 +66,11 @@ #define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH) /* FPGA */ +#define CONFIG_FPGA #define CONFIG_QONG_FPGA 1 #define CONFIG_FPGA_BASE (CS1_BASE) +#define CONFIG_FPGA_LATTICE +#define CONFIG_FPGA_COUNT 1 #ifdef CONFIG_QONG_FPGA /* Ethernet */ @@ -86,6 +89,23 @@ #define CONFIG_BMP_16BPP #define CONFIG_DISPLAY_COM57H5M10XRC +/* USB */ +#define CONFIG_CMD_USB +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI /* Enable EHCI USB support */ +#define CONFIG_USB_EHCI_MXC +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_MXC_USB_PORT 2 +#define CONFIG_MXC_USB_PORTSC (MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT) +#define CONFIG_MXC_USB_FLAGS MXC_EHCI_POWER_PINS_ENABLED +#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_STORAGE +#define CONFIG_DOS_PARTITION +#define CONFIG_SUPPORT_VFAT +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#endif /* CONFIG_CMD_USB */ + /* * Reducing the ARP timeout from default 5 seconds to 200ms we speed up the * initial TFTP transfer, should the user wish one, significantly. @@ -105,25 +125,16 @@ #include <config_cmd_default.h> #define CONFIG_CMD_CACHE -#define CONFIG_CMD_PING +#define CONFIG_CMD_DATE #define CONFIG_CMD_DHCP -#define CONFIG_CMD_NET #define CONFIG_CMD_MII #define CONFIG_CMD_NAND +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_SETEXPR #define CONFIG_CMD_SPI -#define CONFIG_CMD_DATE -#define BOARD_LATE_INIT -/* - * You can compile in a MAC address and your custom net settings by using - * the following syntax. - * - * #define CONFIG_ETHADDR xx:xx:xx:xx:xx:xx - * #define CONFIG_SERVERIP <server ip> - * #define CONFIG_IPADDR <board ip> - * #define CONFIG_GATEWAYIP <gateway ip> - * #define CONFIG_NETMASK <your netmask> - */ +#define BOARD_LATE_INIT #define CONFIG_BOOTDELAY 5 @@ -145,7 +156,7 @@ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ "addmisc=setenv bootargs ${bootargs}\0" \ "uboot_addr=A0000000\0" \ - "kernel_addr=A00A0000\0" \ + "kernel_addr=A00C0000\0" \ "ramdisk_addr=A0300000\0" \ "u-boot=qong/u-boot.bin\0" \ "kernel_addr_r=80800000\0" \ @@ -247,7 +258,7 @@ extern int qong_nand_rdy(void *chip); #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_SECT_SIZE 0x20000 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x60000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x80000) /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) @@ -277,10 +288,14 @@ extern int qong_nand_rdy(void *chip); #define CONFIG_LZO #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ #define CONFIG_FLASH_CFI_MTD -#define MTDIDS_DEFAULT "nor0=physmap-flash.0" +#define MTDIDS_DEFAULT "nor0=physmap-flash.0," \ + "nand0=gen_nand" #define MTDPARTS_DEFAULT \ - "mtdparts=physmap-flash.0:384k(U-Boot),128k(env1)," \ - "128k(env2),2432k(kernel),13m(ramdisk),-(user)" + "mtdparts=physmap-flash.0:" \ + "512k(U-Boot),128k(env1),128k(env2)," \ + "2304k(kernel),13m(ramdisk),-(user);" \ + "gen_nand:" \ + "128m(nand)" /* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE 0x80000000 |
