diff options
Diffstat (limited to 'include/configs/omap3_cairo.h')
| -rw-r--r-- | include/configs/omap3_cairo.h | 286 |
1 files changed, 286 insertions, 0 deletions
diff --git a/include/configs/omap3_cairo.h b/include/configs/omap3_cairo.h new file mode 100644 index 0000000000..3030054949 --- /dev/null +++ b/include/configs/omap3_cairo.h @@ -0,0 +1,286 @@ +/* + * Configuration settings for the QUIPOS Cairo board. + * + * Copyright (C) DENX GmbH + * + * Author : + * Albert ARIBAUD <albert.aribaud@3adev.fr> + * + * Derived from EVM code by + * Manikandan Pillai <mani.pillai@ti.com> + * Itself derived from Beagle Board and 3430 SDP code by + * Richard Woodruff <r-woodruff2@ti.com> + * Syed Mohammed Khasim <khasim@ti.com> + * + * Also derived from include/configs/omap3_beagle.h + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __OMAP3_CAIRO_CONFIG_H +#define __OMAP3_CAIRO_CONFIG_H + +#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ + +/* + * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM + * 64 bytes before this address should be set aside for u-boot.img's + * header. That is 0x800FFFC0--0x80100000 should not be used for any + * other needs. We use this rather than the inherited defines from + * ti_armv7_common.h for backwards compatibility. + */ +#define CONFIG_SYS_TEXT_BASE 0x80100000 +#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SPL_BSS_START_ADDR 0x80000000 +#define CONFIG_SPL_BSS_MAX_SIZE (512 << 10) /* 512 KB */ +#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 + +#define CONFIG_NAND + +#include <configs/ti_omap3_common.h> + +/* + * Display CPU and Board information + */ +#define CONFIG_DISPLAY_CPUINFO 1 +#define CONFIG_DISPLAY_BOARDINFO 1 + +#define CONFIG_MISC_INIT_R + +#define CONFIG_REVISION_TAG 1 +#define CONFIG_ENV_OVERWRITE + +/* Enable Multi Bus support for I2C */ +#define CONFIG_I2C_MULTI_BUS 1 + +/* Probe all devices */ +#define CONFIG_SYS_I2C_NOPROBES { {0x0, 0x0} } + +#define CONFIG_NAND + +/* commands to include */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_SETEXPR /* Evaluate expressions */ +#define CONFIG_CMD_NAND_LOCK_UNLOCK + +/* Disable some commands */ +#undef CONFIG_CMD_FPGA /* FPGA configuration Support */ +#undef CONFIG_CMD_IMI /* iminfo */ +#undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ + +/* + * TWL4030 + */ +#define CONFIG_TWL4030_LED 1 + +/* + * Board NAND Info. + */ +#define CONFIG_SYS_NAND_QUIET_TEST 1 +#define CONFIG_NAND_OMAP_GPMC +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ + /* devices */ +/* override default CONFIG_BOOTDELAY */ +#undef CONFIG_BOOTDELAY +#define CONFIG_BOOTDELAY 0 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "machid=ffffffff\0" \ + "fdt_high=0x87000000\0" \ + "baudrate=115200\0" \ + "ethaddr=00:50:C2:7E:90:F0\0" \ + "fec_addr=00:50:C2:7E:90:F0\0" \ + "netmask=255.255.255.0\0" \ + "ipaddr=192.168.2.9\0" \ + "gateway=192.168.2.1\0" \ + "serverip=192.168.2.10\0" \ + "nfshost=192.168.2.10\0" \ + "stdin=serial\0" \ + "stdout=serial\0" \ + "stderr=serial\0" \ + "bootargs_mmc_ramdisk=mem=128M " \ + "console=ttyO1,115200n8 " \ + "root=/dev/ram0 rw " \ + "initrd=0x81600000,16M " \ + "mpurate=600 ramdisk_size=16384 omapfb.rotate=1 " \ + "omapfb.rotate_type=1 omap_vout.vid1_static_vrfb_alloc=y\0" \ + "mmcboot=mmc init; " \ + "fatload mmc 0 0x80000000 uImage; " \ + "fatload mmc 0 0x81600000 ramdisk.gz; " \ + "setenv bootargs ${bootargs_mmc_ramdisk}; " \ + "bootm 0x80000000\0" \ + "bootargs_nfs=mem=99M console=ttyO0,115200n8 noinitrd rw ip=dhcp " \ + "root=/dev/nfs " \ + "nfsroot=192.168.2.10:/home/spiid/workdir/Quipos/rootfs,nolock " \ + "mpurate=600 omapfb.rotate=1 omapfb.rotate_type=1 " \ + "omap_vout.vid1_static_vrfb_alloc=y\0" \ + "boot_nfs=run get_kernel; setenv bootargs ${bootargs_nfs}; " \ + "bootm 0x80000000\0" \ + "bootargs_nand=mem=128M console=ttyO1,115200n8 noinitrd " \ + "root=/dev/mtdblock4 rw rootfstype=jffs2 mpurate=600 " \ + "omap_vout.vid1_static_vrfb_alloc=y omapfb.rotate=1 " \ + "omapfb.rotate_type=1\0" \ + "boot_nand=nand read.i 0x80000000 280000 300000; setenv " \ + "bootargs ${bootargs_nand}; bootm 0x80000000\0" \ + "ledorange=i2c dev 1; i2c mw 60 00 00 1; i2c mw 60 14 FF 1; " \ + "i2c mw 60 15 FF 1; i2c mw 60 16 FF 1; i2c mw 60 17 FF 1; " \ + "i2c mw 60 09 10 1; i2c mw 60 06 10 1\0" \ + "ledgreen=i2c dev 1; i2c mw 60 00 00 1; i2c mw 60 14 FF 1; " \ + "i2c mw 60 15 FF 1; i2c mw 60 16 FF 1; i2c mw 60 17 FF 1; i2c " \ + "mw 60 09 00 1; i2c mw 60 06 10 1\0" \ + "ledoff=i2c dev 1; i2c mw 60 00 00 1; i2c mw 60 14 FF 1; " \ + "i2c mw 60 15 FF 1; i2c mw 60 16 FF 1; i2c mw 60 17 FF 1; " \ + "i2c mw 60 09 00 1; i2c mw 60 06 0 1\0" \ + "ledred=i2c dev 1; i2c mw 60 00 00 1; i2c mw 60 14 FF 1; " \ + "i2c mw 60 15 FF 1; i2c mw 60 16 FF 1; i2c mw 60 17 FF 1; " \ + "i2c mw 60 09 10 1; i2c mw 60 06 0 1\0" \ + "flash_xloader=mw.b 0x81600000 0xff 0x20000; " \ + "nand erase 0 20000; " \ + "fatload mmc 0 0x81600000 MLO; " \ + "nandecc hw; " \ + "nand write.i 0x81600000 0 20000;\0" \ + "flash_uboot=mw.b 0x81600000 0xff 0x40000; " \ + "nand erase 80000 40000; " \ + "fatload mmc 0 0x81600000 u-boot.bin; " \ + "nandecc sw; " \ + "nand write.i 0x81600000 80000 40000;\0" \ + "flash_kernel=mw.b 0x81600000 0xff 0x300000; " \ + "nand erase 280000 300000; " \ + "fatload mmc 0 0x81600000 uImage; " \ + "nandecc sw; " \ + "nand write.i 0x81600000 280000 300000;\0" \ + "flash_rootfs=fatload mmc 0 0x81600000 rootfs.jffs2; " \ + "nandecc sw; " \ + "nand write.jffs2 0x680000 0xFF ${filesize}; " \ + "nand erase 680000 ${filesize}; " \ + "nand write.jffs2 81600000 680000 ${filesize};\0" \ + "flash_scrub=nand scrub; " \ + "run flash_xloader; " \ + "run flash_uboot; " \ + "run flash_kernel; " \ + "run flash_rootfs;\0" \ + "flash_all=run ledred; " \ + "nand erase.chip; " \ + "run ledorange; " \ + "run flash_xloader; " \ + "run flash_uboot; " \ + "run flash_kernel; " \ + "run flash_rootfs; " \ + "run ledgreen; " \ + "run boot_nand; \0" \ + +#define CONFIG_BOOTCOMMAND \ + "if fatload mmc 0 0x81600000 MLO; then run flash_all; " \ + "else run boot_nand; fi" + +/* + * OMAP3 has 12 GP timers, they can be driven by the system clock + * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). + * This rate is divided by a local divisor. + */ +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ + +/* **** PISMO SUPPORT *** */ +#if defined(CONFIG_CMD_NAND) +#define CONFIG_SYS_FLASH_BASE NAND_BASE +#endif + +/* Monitor at start of flash */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP + +#define CONFIG_ENV_IS_IN_NAND 1 +#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ +#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */ +#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */ + +#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ +#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET +#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET + +#define CONFIG_OMAP3_SPI + +#define CONFIG_SYS_CACHELINE_SIZE 64 + +/* Defines for SPL */ +#define CONFIG_SPL_OMAP3_ID_NAND + +/* NAND boot config */ +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 +#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\ + 10, 11, 12, 13} +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 +/* NAND: SPL falcon mode configs */ +#ifdef CONFIG_SPL_OS_BOOT +#define CONFIG_CMD_SPL_NAND_OFS 0x240000 +#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000 +#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000 +#endif + +/* env defaults */ +#define CONFIG_BOOTFILE "uImage" + +/* Override OMAP3 common serial console configuration from UART3 + * to UART2. + * + * Attention: for UART2, special MUX settings (MUX_DEFAULT(), MCBSP3) + * are needed and peripheral clocks for UART2 must be enabled in + * function per_clocks_enable(). + */ +#undef CONFIG_CONS_INDEX +#define CONFIG_CONS_INDEX 2 +#ifdef CONFIG_SPL_BUILD +#undef CONFIG_SYS_NS16550_COM3 +#define CONFIG_SYS_NS16550_COM2 OMAP34XX_UART2 +#undef CONFIG_SERIAL3 +#define CONFIG_SERIAL2 +#endif + +/* Keep old prompt in case some existing script depends on it */ +#undef CONFIG_SYS_PROMPT +#define CONFIG_SYS_PROMPT "Cairo # " + +/* Provide MACH_TYPE for compatibility with non-DT kernels */ +#define MACH_TYPE_OMAP3_CAIRO 3063 +#define CONFIG_MACH_TYPE MACH_TYPE_OMAP3_CAIRO + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ + +/* **** PISMO SUPPORT *** */ + +#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */ + /* on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */ + +/*----------------------------------------------------------------------- + * CFI FLASH driver setup + */ +/* timeout values are in ticks */ +#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ) +#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ) + +/* Flash banks JFFS2 should use */ +#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \ + CONFIG_SYS_MAX_NAND_DEVICE) +#define CONFIG_SYS_JFFS2_MEM_NAND +/* use flash_info[2] */ +#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS +#define CONFIG_SYS_JFFS2_NUM_BANKS 1 + +#endif /* __OMAP3_CAIRO_CONFIG_H */ |
