diff options
Diffstat (limited to 'include/configs/ep8260.h')
| -rw-r--r-- | include/configs/ep8260.h | 336 |
1 files changed, 168 insertions, 168 deletions
diff --git a/include/configs/ep8260.h b/include/configs/ep8260.h index 9a602c3afb..d49d02f287 100644 --- a/include/configs/ep8260.h +++ b/include/configs/ep8260.h @@ -33,7 +33,7 @@ * - 16M Flash (4 x AM29DL323DB90WDI) * - 128k NVRAM with RTC * - * "EP8260 H2, V.1.3" (CFG_EP8260_H2) + * "EP8260 H2, V.1.3" (CONFIG_SYS_EP8260_H2) * - 300MHz/133MHz/66MHz * - 64M 60x Bus SDRAM * - 32M Local Bus SDRAM @@ -45,8 +45,8 @@ #define __CONFIG_H /* Define this to enable support the EP8260 H2 version */ -#define CFG_EP8260_H2 1 -/* #undef CFG_EP8260_H2 */ +#define CONFIG_SYS_EP8260_H2 1 +/* #undef CONFIG_SYS_EP8260_H2 */ #define CONFIG_CPM2 1 /* Has a CPM2 */ @@ -75,10 +75,10 @@ * 0x6 0x1 66 133 266 * 0x6 0x2 66 133 300 */ -#ifdef CFG_EP8260_H2 -#define CFG_SBC_MODCK_H (HRCW_MODCK_H0110) +#ifdef CONFIG_SYS_EP8260_H2 +#define CONFIG_SYS_SBC_MODCK_H (HRCW_MODCK_H0110) #else -#define CFG_SBC_MODCK_H (HRCW_MODCK_H0110) +#define CONFIG_SYS_SBC_MODCK_H (HRCW_MODCK_H0110) #endif /* Define this if you want to boot from 0x00000100. If you don't define @@ -87,26 +87,26 @@ * way to do that is to program the bootloader at both addresses. * It is suggested that you just let U-Boot live at 0x00000000. */ -/* #define CFG_SBC_BOOT_LOW 1 */ /* only for HRCW */ -/* #undef CFG_SBC_BOOT_LOW */ +/* #define CONFIG_SYS_SBC_BOOT_LOW 1 */ /* only for HRCW */ +/* #undef CONFIG_SYS_SBC_BOOT_LOW */ /* The reset command will not work as expected if the reset address does * not point to the correct address. */ -#define CFG_RESET_ADDRESS 0xFFF00100 +#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 /* What should the base address of the main FLASH be and how big is * it (in MBytes)? This must contain TEXT_BASE from board/ep8260/config.mk * The main FLASH is whichever is connected to *CS0. U-Boot expects * this to be the SIMM. */ -#ifdef CFG_EP8260_H2 -#define CFG_FLASH0_BASE 0xFE000000 -#define CFG_FLASH0_SIZE 32 +#ifdef CONFIG_SYS_EP8260_H2 +#define CONFIG_SYS_FLASH0_BASE 0xFE000000 +#define CONFIG_SYS_FLASH0_SIZE 32 #else -#define CFG_FLASH0_BASE 0xFF000000 -#define CFG_FLASH0_SIZE 16 +#define CONFIG_SYS_FLASH0_BASE 0xFF000000 +#define CONFIG_SYS_FLASH0_SIZE 16 #endif /* What should the base address of the secondary FLASH be and how big @@ -114,41 +114,41 @@ * to *CS6. U-Boot expects this to be the on board FLASH. If you don't * want it enabled, don't define these constants. */ -#define CFG_FLASH1_BASE 0 -#define CFG_FLASH1_SIZE 0 -#undef CFG_FLASH1_BASE -#undef CFG_FLASH1_SIZE +#define CONFIG_SYS_FLASH1_BASE 0 +#define CONFIG_SYS_FLASH1_SIZE 0 +#undef CONFIG_SYS_FLASH1_BASE +#undef CONFIG_SYS_FLASH1_SIZE /* What should be the base address of SDRAM DIMM (60x bus) and how big is * it (in Mbytes)? */ -#define CFG_SDRAM0_BASE 0x00000000 -#define CFG_SDRAM0_SIZE 64 +#define CONFIG_SYS_SDRAM0_BASE 0x00000000 +#define CONFIG_SYS_SDRAM0_SIZE 64 -/* define CFG_LSDRAM if you want to enable the 32M SDRAM on the +/* define CONFIG_SYS_LSDRAM if you want to enable the 32M SDRAM on the * local bus (8260 local bus is NOT cacheable!) */ -/* #define CFG_LSDRAM */ -#undef CFG_LSDRAM +/* #define CONFIG_SYS_LSDRAM */ +#undef CONFIG_SYS_LSDRAM -#ifdef CFG_LSDRAM +#ifdef CONFIG_SYS_LSDRAM /* What should be the base address of SDRAM DIMM (local bus) and how big is * it (in Mbytes)? */ - #define CFG_SDRAM1_BASE 0x04000000 - #define CFG_SDRAM1_SIZE 32 + #define CONFIG_SYS_SDRAM1_BASE 0x04000000 + #define CONFIG_SYS_SDRAM1_SIZE 32 #else - #define CFG_SDRAM1_BASE 0 - #define CFG_SDRAM1_SIZE 0 - #undef CFG_SDRAM1_BASE - #undef CFG_SDRAM1_SIZE -#endif /* CFG_LSDRAM */ + #define CONFIG_SYS_SDRAM1_BASE 0 + #define CONFIG_SYS_SDRAM1_SIZE 0 + #undef CONFIG_SYS_SDRAM1_BASE + #undef CONFIG_SYS_SDRAM1_SIZE +#endif /* CONFIG_SYS_LSDRAM */ /* What should be the base address of NVRAM and how big is * it (in Bytes) */ -#define CFG_NVRAM_BASE_ADDR 0xFA080000 -#define CFG_NVRAM_SIZE (128*1024)-16 +#define CONFIG_SYS_NVRAM_BASE_ADDR 0xFA080000 +#define CONFIG_SYS_NVRAM_SIZE (128*1024)-16 /* The RTC is a Dallas DS1556 */ @@ -157,8 +157,8 @@ /* What should be the base address of the LEDs and switch S0? * If you don't want them enabled, don't define this. */ -#define CFG_LED_BASE 0x00000000 -#undef CFG_LED_BASE +#define CONFIG_SYS_LED_BASE 0x00000000 +#undef CONFIG_SYS_LED_BASE /* * select serial console configuration @@ -198,21 +198,21 @@ * - RAM for BD/Buffers is on the local Bus (see 28-13) * - Enable Half Duplex in FSMR */ -# define CFG_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK) -# define CFG_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16) +# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK) +# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16) /* * - RAM for BD/Buffers is on the local Bus (see 28-13) */ -#ifdef CFG_LSDRAM - #define CFG_CPMFCR_RAMTYPE 3 -#else /* CFG_LSDRAM */ - #define CFG_CPMFCR_RAMTYPE 0 -#endif /* CFG_LSDRAM */ +#ifdef CONFIG_SYS_LSDRAM + #define CONFIG_SYS_CPMFCR_RAMTYPE 3 +#else /* CONFIG_SYS_LSDRAM */ + #define CONFIG_SYS_CPMFCR_RAMTYPE 0 +#endif /* CONFIG_SYS_LSDRAM */ /* - Enable Half Duplex in FSMR */ -/* # define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */ -# define CFG_FCC_PSMR 0 +/* # define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */ +# define CONFIG_SYS_FCC_PSMR 0 #else /* CONFIG_ETHER_INDEX */ # error "on EP8260 ethernet must be FCC3" @@ -227,8 +227,8 @@ */ #undef CONFIG_HARD_I2C /* I2C with hardware support */ #define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F /* * Software (bit-bang) I2C driver configuration @@ -258,7 +258,7 @@ #define CONFIG_ENV_OVERWRITE /* What should the console's baud rate be? */ -#ifdef CFG_EP8260_H2 +#ifdef CONFIG_SYS_EP8260_H2 #define CONFIG_BAUDRATE 9600 #else #define CONFIG_BAUDRATE 115200 @@ -274,10 +274,10 @@ #define CONFIG_BOOTDELAY -1 /* undef this to save memory */ -#define CFG_LONGHELP +#define CONFIG_SYS_LONGHELP /* Monitor Command Prompt */ -#define CFG_PROMPT "=> " +#define CONFIG_SYS_PROMPT "=> " /* Define this variable to enable the "hush" shell (from Busybox) as command line interpreter, thus enabling @@ -287,8 +287,8 @@ If undefined, you get the old, much simpler behaviour with a somewhat smapper memory footprint. */ -#define CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /* @@ -327,11 +327,11 @@ #undef CONFIG_CMD_XIMG /* Where do the internal registers live? */ -#define CFG_IMMR 0xF0000000 -#define CFG_DEFAULT_IMMR 0x00010000 +#define CONFIG_SYS_IMMR 0xF0000000 +#define CONFIG_SYS_DEFAULT_IMMR 0x00010000 /* Where do the on board registers (CS4) live? */ -#define CFG_REGS_BASE 0xFA000000 +#define CONFIG_SYS_REGS_BASE 0xFA000000 /***************************************************************************** * @@ -348,35 +348,35 @@ * Miscellaneous configurable options */ #if defined(CONFIG_CMD_KGDB) -# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -# define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif /* Print Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT)+16) +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16) -#define CFG_MAXARGS 8 /* max number of command args */ +#define CONFIG_SYS_MAXARGS 8 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#ifdef CFG_LSDRAM - #define CFG_MEMTEST_START 0x04000000 /* memtest works on */ - #define CFG_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */ +#ifdef CONFIG_SYS_LSDRAM + #define CONFIG_SYS_MEMTEST_START 0x04000000 /* memtest works on */ + #define CONFIG_SYS_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */ #else - #define CFG_MEMTEST_START 0x00000000 /* memtest works on */ - #define CFG_MEMTEST_END 0x02000000 /* 0-32 MB in SDRAM */ -#endif /* CFG_LSDRAM */ + #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ + #define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0-32 MB in SDRAM */ +#endif /* CONFIG_SYS_LSDRAM */ #define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ -#define CFG_LOAD_ADDR 0x00100000 /* default load address */ -#define CFG_TFTP_LOADADDR 0x00100000 /* default load address for network file downloads */ +#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ +#define CONFIG_SYS_TFTP_LOADADDR 0x00100000 /* default load address for network file downloads */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /* valid baudrates */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* * Low Level Configuration Settings @@ -384,119 +384,119 @@ * You should know what you are doing if you make changes here. */ -#define CFG_FLASH_BASE CFG_FLASH0_BASE -#define CFG_SDRAM_BASE CFG_SDRAM0_BASE +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE /*----------------------------------------------------------------------- * Hard Reset Configuration Words */ -#if defined(CFG_SBC_BOOT_LOW) -# define CFG_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) +#if defined(CONFIG_SYS_SBC_BOOT_LOW) +# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) #else -# define CFG_SBC_HRCW_BOOT_FLAGS (0x00000000) -#endif /* defined(CFG_SBC_BOOT_LOW) */ +# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0x00000000) +#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */ -#ifdef CFG_EP8260_H2 -/* get the HRCW ISB field from CFG_DEFAULT_IMMR */ -#define CFG_SBC_HRCW_IMMR ( ((CFG_DEFAULT_IMMR & 0x10000000) >> 10) |\ - ((CFG_DEFAULT_IMMR & 0x01000000) >> 7) |\ - ((CFG_DEFAULT_IMMR & 0x00100000) >> 4) ) +#ifdef CONFIG_SYS_EP8260_H2 +/* get the HRCW ISB field from CONFIG_SYS_DEFAULT_IMMR */ +#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_DEFAULT_IMMR & 0x10000000) >> 10) |\ + ((CONFIG_SYS_DEFAULT_IMMR & 0x01000000) >> 7) |\ + ((CONFIG_SYS_DEFAULT_IMMR & 0x00100000) >> 4) ) -#define CFG_HRCW_MASTER (HRCW_EBM |\ +#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM |\ HRCW_L2CPC01 |\ - CFG_SBC_HRCW_IMMR |\ + CONFIG_SYS_SBC_HRCW_IMMR |\ HRCW_APPC10 |\ HRCW_CS10PC01 |\ - CFG_SBC_MODCK_H |\ - CFG_SBC_HRCW_BOOT_FLAGS) + CONFIG_SYS_SBC_MODCK_H |\ + CONFIG_SYS_SBC_HRCW_BOOT_FLAGS) #else -#define CFG_HRCW_MASTER 0x10400245 +#define CONFIG_SYS_HRCW_MASTER 0x10400245 #endif /* no slaves */ -#define CFG_HRCW_SLAVE1 0 -#define CFG_HRCW_SLAVE2 0 -#define CFG_HRCW_SLAVE3 0 -#define CFG_HRCW_SLAVE4 0 -#define CFG_HRCW_SLAVE5 0 -#define CFG_HRCW_SLAVE6 0 -#define CFG_HRCW_SLAVE7 0 +#define CONFIG_SYS_HRCW_SLAVE1 0 +#define CONFIG_SYS_HRCW_SLAVE2 0 +#define CONFIG_SYS_HRCW_SLAVE3 0 +#define CONFIG_SYS_HRCW_SLAVE4 0 +#define CONFIG_SYS_HRCW_SLAVE5 0 +#define CONFIG_SYS_HRCW_SLAVE6 0 +#define CONFIG_SYS_HRCW_SLAVE7 0 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ -#define CFG_INIT_RAM_ADDR CFG_IMMR -#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ -#define CFG_GBL_DATA_SIZE 128 /* bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 - * Note also that the logic that sets CFG_RAMBOOT is platform dependent. + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent. */ -#define CFG_MONITOR_BASE TEXT_BASE +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -# define CFG_RAMBOOT +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT #endif -#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH and environment organization */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#ifdef CFG_EP8260_H2 -#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#ifdef CONFIG_SYS_EP8260_H2 +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ #else -#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ #endif -#ifdef CFG_EP8260_H2 -#define CFG_FLASH_ERASE_TOUT 240000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#ifdef CONFIG_SYS_EP8260_H2 +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #else -#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ #endif -#ifndef CFG_RAMBOOT +#ifndef CONFIG_SYS_RAMBOOT # define CONFIG_ENV_IS_IN_FLASH 1 # ifdef CONFIG_ENV_IN_OWN_SECT -# define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) # define CONFIG_ENV_SECT_SIZE 0x40000 # else -# define CONFIG_ENV_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN - CONFIG_ENV_SECT_SIZE) +# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE) # define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ # define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */ # endif /* CONFIG_ENV_IN_OWN_SECT */ #else # define CONFIG_ENV_IS_IN_NVRAM 1 -# define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) +# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) # define CONFIG_ENV_SIZE 0x200 -#endif /* CFG_RAMBOOT */ +#endif /* CONFIG_SYS_RAMBOOT */ /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ #if defined(CONFIG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- @@ -509,38 +509,38 @@ * * HID1 has only read-only information - nothing to set. */ -#define CFG_HID0_INIT (HID0_ICE |\ +#define CONFIG_SYS_HID0_INIT (HID0_ICE |\ HID0_DCE |\ HID0_ICFI |\ HID0_DCI |\ HID0_IFEM |\ HID0_ABE) -#ifdef CFG_LSDRAM +#ifdef CONFIG_SYS_LSDRAM /* 8260 local bus is NOT cacheable */ -#define CFG_HID0_FINAL (/*HID0_ICE |*/\ +#define CONFIG_SYS_HID0_FINAL (/*HID0_ICE |*/\ HID0_IFEM |\ HID0_ABE |\ HID0_EMCP) -#else /* !CFG_LSDRAM */ -#define CFG_HID0_FINAL (HID0_ICE |\ +#else /* !CONFIG_SYS_LSDRAM */ +#define CONFIG_SYS_HID0_FINAL (HID0_ICE |\ HID0_IFEM |\ HID0_ABE |\ HID0_EMCP) -#endif /* CFG_LSDRAM */ +#endif /* CONFIG_SYS_LSDRAM */ -#define CFG_HID2 0 +#define CONFIG_SYS_HID2 0 /*----------------------------------------------------------------------- * RMR - Reset Mode Register *----------------------------------------------------------------------- */ -#define CFG_RMR 0 +#define CONFIG_SYS_RMR 0 /*----------------------------------------------------------------------- * BCR - Bus Configuration 4-25 *----------------------------------------------------------------------- */ -#define CFG_BCR (BCR_EBM |\ +#define CONFIG_SYS_BCR (BCR_EBM |\ BCR_PLDP |\ BCR_EAV |\ BCR_NPQM0) @@ -549,7 +549,7 @@ * SIUMCR - SIU Module Configuration 4-31 *----------------------------------------------------------------------- */ -#define CFG_SIUMCR (SIUMCR_L2CPC01 |\ +#define CONFIG_SYS_SIUMCR (SIUMCR_L2CPC01 |\ SIUMCR_APPC10 |\ SIUMCR_CS10PC01) @@ -559,25 +559,25 @@ *----------------------------------------------------------------------- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable */ -#ifdef CFG_EP8260_H2 +#ifdef CONFIG_SYS_EP8260_H2 /* TBD: Find out why setting the BMT to 0xff causes the FCC to * generate TX buffer underrun errors for large packets under * Linux */ -#define CFG_SYPCR_BMT 0x00000600 +#define CONFIG_SYS_SYPCR_BMT 0x00000600 #else -#define CFG_SYPCR_BMT SYPCR_BMT +#define CONFIG_SYS_SYPCR_BMT SYPCR_BMT #endif -#ifdef CFG_LSDRAM -#define CFG_SYPCR (SYPCR_SWTC |\ - CFG_SYPCR_BMT |\ +#ifdef CONFIG_SYS_LSDRAM +#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\ + CONFIG_SYS_SYPCR_BMT |\ SYPCR_PBME |\ SYPCR_LBME |\ SYPCR_SWP) #else -#define CFG_SYPCR (SYPCR_SWTC |\ - CFG_SYPCR_BMT |\ +#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\ + CONFIG_SYS_SYPCR_BMT |\ SYPCR_PBME |\ SYPCR_SWP) #endif @@ -588,7 +588,7 @@ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, * and enable Time Counter */ -#define CFG_TMCNTSC (TMCNTSC_SEC |\ +#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\ TMCNTSC_ALR |\ TMCNTSC_TCF |\ TMCNTSC_TCE) @@ -599,35 +599,35 @@ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable * Periodic timer */ -#ifdef CFG_EP8260_H2 -#define CFG_PISCR (PISCR_PS |\ +#ifdef CONFIG_SYS_EP8260_H2 +#define CONFIG_SYS_PISCR (PISCR_PS |\ PISCR_PTF |\ PISCR_PTE) #else -#define CFG_PISCR 0 +#define CONFIG_SYS_PISCR 0 #endif /*----------------------------------------------------------------------- * SCCR - System Clock Control 9-8 *----------------------------------------------------------------------- */ -#ifdef CFG_EP8260_H2 -#define CFG_SCCR (SCCR_DFBRG00) +#ifdef CONFIG_SYS_EP8260_H2 +#define CONFIG_SYS_SCCR (SCCR_DFBRG00) #else -#define CFG_SCCR (SCCR_DFBRG01) +#define CONFIG_SYS_SCCR (SCCR_DFBRG01) #endif /*----------------------------------------------------------------------- * RCCR - RISC Controller Configuration 13-7 *----------------------------------------------------------------------- */ -#define CFG_RCCR 0 +#define CONFIG_SYS_RCCR 0 /*----------------------------------------------------------------------- * MPTPR - Memory Refresh Timer Prescale Register 10-32 *----------------------------------------------------------------------- */ -#define CFG_MPTPR (0x0A00 & MPTPR_PTP_MSK) +#define CONFIG_SYS_MPTPR (0x0A00 & MPTPR_PTP_MSK) /* * Init Memory Controller: @@ -659,13 +659,13 @@ /* Bank 0 - FLASH * */ -#define CFG_BR0_PRELIM ((CFG_FLASH0_BASE & BRx_BA_MSK) |\ +#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\ BRx_PS_64 |\ BRx_DECC_NONE |\ BRx_MS_GPCM_P |\ BRx_V) -#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH0_SIZE) |\ +#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\ ORxG_CSNT |\ ORxG_ACS_DIV1 |\ ORxG_SCY_8_CLK |\ @@ -674,71 +674,71 @@ /* Bank 1 - SDRAM * PSDRAM */ -#define CFG_BR1_PRELIM ((CFG_SDRAM0_BASE & BRx_BA_MSK) |\ +#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\ BRx_PS_64 |\ BRx_MS_SDRAM_P |\ BRx_V) -#define CFG_OR1_PRELIM (MEG_TO_AM(CFG_SDRAM0_SIZE) |\ +#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\ ORxS_BPD_4 |\ ORxS_ROWST_PBI1_A6 |\ ORxS_NUMR_12) -#ifdef CFG_EP8260_H2 -#define CFG_PSDMR 0xC34E246E +#ifdef CONFIG_SYS_EP8260_H2 +#define CONFIG_SYS_PSDMR 0xC34E246E #else -#define CFG_PSDMR 0xC34E2462 +#define CONFIG_SYS_PSDMR 0xC34E2462 #endif -#define CFG_PSRT 0x64 +#define CONFIG_SYS_PSRT 0x64 -#ifdef CFG_LSDRAM +#ifdef CONFIG_SYS_LSDRAM /* Bank 2 - SDRAM * LSDRAM */ - #define CFG_BR2_PRELIM ((CFG_SDRAM1_BASE & BRx_BA_MSK) |\ + #define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\ BRx_PS_32 |\ BRx_MS_SDRAM_L |\ BRx_V) - #define CFG_OR2_PRELIM (MEG_TO_AM(CFG_SDRAM1_SIZE) |\ + #define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE) |\ ORxS_BPD_4 |\ ORxS_ROWST_PBI0_A9 |\ ORxS_NUMR_12) - #define CFG_LSDMR 0x416A2562 - #define CFG_LSRT 0x64 + #define CONFIG_SYS_LSDMR 0x416A2562 + #define CONFIG_SYS_LSRT 0x64 #else - #define CFG_LSRT 0x0 -#endif /* CFG_LSDRAM */ + #define CONFIG_SYS_LSRT 0x0 +#endif /* CONFIG_SYS_LSDRAM */ /* Bank 4 - On board registers * NVRTC and BCSR */ -#define CFG_BR4_PRELIM ((CFG_REGS_BASE & BRx_BA_MSK) |\ +#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) |\ BRx_PS_8 |\ BRx_MS_GPCM_P |\ BRx_V) /* -#define CFG_OR4_PRELIM (ORxG_AM_MSK |\ +#define CONFIG_SYS_OR4_PRELIM (ORxG_AM_MSK |\ ORxG_CSNT |\ ORxG_ACS_DIV1 |\ ORxG_SCY_10_CLK |\ ORxG_TRLX) */ -#define CFG_OR4_PRELIM 0xfff00854 +#define CONFIG_SYS_OR4_PRELIM 0xfff00854 #ifdef _NOT_USED_SINCE_NOT_WORKING_ /* Bank 8 - On board registers * PCMCIA (currently not working!) */ -#define CFG_BR8_PRELIM ((CFG_REGS_BASE & BRx_BA_MSK) |\ +#define CONFIG_SYS_BR8_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) |\ BRx_PS_16 |\ BRx_MS_GPCM_P |\ BRx_V) -#define CFG_OR8_PRELIM (ORxG_AM_MSK |\ +#define CONFIG_SYS_OR8_PRELIM (ORxG_AM_MSK |\ ORxG_CSNT |\ ORxG_ACS_DIV1 |\ ORxG_SETA |\ |
