diff options
Diffstat (limited to 'include/configs/MPC8610HPCD.h')
| -rw-r--r-- | include/configs/MPC8610HPCD.h | 344 |
1 files changed, 172 insertions, 172 deletions
diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 4eee21ca85..678e1e151a 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -31,10 +31,10 @@ #endif #ifdef RUN_DIAG -#define CFG_DIAG_ADDR 0xff800000 +#define CONFIG_SYS_DIAG_ADDR 0xff800000 #endif -#define CFG_RESET_ADDRESS 0xfff00100 +#define CONFIG_SYS_RESET_ADDRESS 0xfff00100 #define CONFIG_PCI 1 /* Enable PCI/PCIE*/ #define CONFIG_PCI1 1 /* PCI controler 1 */ @@ -52,7 +52,7 @@ /* * L2CR setup -- make sure this is right for your board! */ -#define CFG_L2 +#define CONFIG_SYS_L2 #define L2_INIT 0 #define L2_ENABLE (L2CR_L2E |0x00100000 ) @@ -63,22 +63,22 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_R 1 -#define CFG_MEMTEST_START 0x00200000 /* memtest region */ -#define CFG_MEMTEST_END 0x00400000 +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ -#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000) -#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000) -#define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000) +#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) +#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) +#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) -#define CFG_DIU_ADDR (CFG_CCSRBAR+0x2c000) +#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR+0x2c000) /* DDR Setup */ #define CONFIG_FSL_DDR2 @@ -89,8 +89,8 @@ #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef -#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_VERY_BIG_RAM #define MPC86xx_DDR_SDRAM_CLK_CNTL @@ -102,64 +102,64 @@ #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ /* These are used when DDR doesn't use SPD. */ -#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */ +#define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ #if 0 /* TODO */ -#define CFG_DDR_CS0_BNDS 0x0000000F -#define CFG_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */ -#define CFG_DDR_TIMING_3 0x00000000 -#define CFG_DDR_TIMING_0 0x00260802 -#define CFG_DDR_TIMING_1 0x3935d322 -#define CFG_DDR_TIMING_2 0x14904cc8 -#define CFG_DDR_MODE_1 0x00480432 -#define CFG_DDR_MODE_2 0x00000000 -#define CFG_DDR_INTERVAL 0x06180100 -#define CFG_DDR_DATA_INIT 0xdeadbeef -#define CFG_DDR_CLK_CTRL 0x03800000 -#define CFG_DDR_OCD_CTRL 0x00000000 -#define CFG_DDR_OCD_STATUS 0x00000000 -#define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ -#define CFG_DDR_CONTROL2 0x04400010 - -#define CFG_DDR_ERR_INT_EN 0x00000000 -#define CFG_DDR_ERR_DIS 0x00000000 -#define CFG_DDR_SBE 0x000f0000 +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */ +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_TIMING_0 0x00260802 +#define CONFIG_SYS_DDR_TIMING_1 0x3935d322 +#define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 +#define CONFIG_SYS_DDR_MODE_1 0x00480432 +#define CONFIG_SYS_DDR_MODE_2 0x00000000 +#define CONFIG_SYS_DDR_INTERVAL 0x06180100 +#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef +#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 +#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 +#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 +#define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ +#define CONFIG_SYS_DDR_CONTROL2 0x04400010 + +#define CONFIG_SYS_DDR_ERR_INT_EN 0x00000000 +#define CONFIG_SYS_DDR_ERR_DIS 0x00000000 +#define CONFIG_SYS_DDR_SBE 0x000f0000 /* * FIXME: Not used in fixed_sdram function */ -#define CFG_DDR_MODE 0x00000022 -#define CFG_DDR_CS1_BNDS 0x00000000 -#define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */ -#define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */ -#define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */ -#define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */ +#define CONFIG_SYS_DDR_MODE 0x00000022 +#define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 +#define CONFIG_SYS_DDR_CS2_BNDS 0x00000FFF /* Not done */ +#define CONFIG_SYS_DDR_CS3_BNDS 0x00000FFF /* Not done */ +#define CONFIG_SYS_DDR_CS4_BNDS 0x00000FFF /* Not done */ +#define CONFIG_SYS_DDR_CS5_BNDS 0x00000FFF /* Not done */ #endif #define CONFIG_ID_EEPROM -#define CFG_I2C_EEPROM_NXID +#define CONFIG_SYS_I2C_EEPROM_NXID #define CONFIG_ID_EEPROM -#define CFG_I2C_EEPROM_ADDR 0x57 -#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CFG_FLASH_BASE 0xf0000000 /* start of FLASH 128M */ -#define CFG_FLASH_BASE2 0xf8000000 +#define CONFIG_SYS_FLASH_BASE 0xf0000000 /* start of FLASH 128M */ +#define CONFIG_SYS_FLASH_BASE2 0xf8000000 -#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2} +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} -#define CFG_BR0_PRELIM 0xf8001001 /* port size 16bit */ -#define CFG_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/ +#define CONFIG_SYS_BR0_PRELIM 0xf8001001 /* port size 16bit */ +#define CONFIG_SYS_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/ -#define CFG_BR1_PRELIM 0xf0001001 /* port size 16bit */ -#define CFG_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */ +#define CONFIG_SYS_BR1_PRELIM 0xf0001001 /* port size 16bit */ +#define CONFIG_SYS_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */ #if 0 /* TODO */ -#define CFG_BR2_PRELIM 0xf0000000 -#define CFG_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */ +#define CONFIG_SYS_BR2_PRELIM 0xf0000000 +#define CONFIG_SYS_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */ #endif -#define CFG_BR3_PRELIM 0xe8000801 /* port size 8bit */ -#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ +#define CONFIG_SYS_BR3_PRELIM 0xe8000801 /* port size 8bit */ +#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ @@ -179,67 +179,67 @@ #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ -#define CFG_PIXIS_VBOOT_MASK 0x0C /* Reset altbank mask*/ +#define CONFIG_SYS_PIXIS_VBOOT_MASK 0x0C /* Reset altbank mask*/ -#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ -#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CONFIG_FLASH_CFI_DRIVER -#define CFG_FLASH_CFI -#define CFG_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -#define CFG_RAMBOOT +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT #else -#undef CFG_RAMBOOT +#undef CONFIG_SYS_RAMBOOT #endif -#if defined(CFG_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) #undef CONFIG_SPD_EEPROM -#define CFG_SDRAM_SIZE 256 +#define CONFIG_SYS_SDRAM_SIZE 256 #endif #undef CONFIG_CLOCKS_IN_MHZ #define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 -#ifndef CFG_INIT_RAM_LOCK -#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#ifndef CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ #else -#define CFG_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */ #endif -#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ +#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ -#define CFG_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */ +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 -#define CFG_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} -#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) -#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) /* Use the HUSH parser */ -#define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* @@ -253,8 +253,8 @@ /* maximum size of the flat tree (8K) */ #define OF_FLAT_TREE_MAX_SIZE 8192 -#define CFG_64BIT_VSPRINTF 1 -#define CFG_64BIT_STRTOUL 1 +#define CONFIG_SYS_64BIT_VSPRINTF 1 +#define CONFIG_SYS_64BIT_STRTOUL 1 /* * I2C @@ -262,46 +262,46 @@ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CFG_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 /* * General PCI * Addresses are mapped 1-1. */ -#define CFG_PCI1_MEM_BASE 0x80000000 -#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE -#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CFG_PCI1_IO_BASE 0x00000000 -#define CFG_PCI1_IO_PHYS 0xe1000000 -#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ /* PCI view of System Memory */ -#define CFG_PCI_MEMORY_BUS 0x00000000 -#define CFG_PCI_MEMORY_PHYS 0x00000000 -#define CFG_PCI_MEMORY_SIZE 0x80000000 +#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000 +#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000 +#define CONFIG_SYS_PCI_MEMORY_SIZE 0x80000000 /* For RTL8139 */ #define KSEG1ADDR(x) ({u32 _x = le32_to_cpu(*(u32 *)(x)); (&_x); }) #define _IO_BASE 0x00000000 /* controller 1, Base address 0xa000 */ -#define CFG_PCIE1_MEM_BASE 0xa0000000 -#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE -#define CFG_PCIE1_MEM_SIZE 0x10000000 /* 256M */ -#define CFG_PCIE1_IO_BASE 0x00000000 -#define CFG_PCIE1_IO_PHYS 0xe3000000 -#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCIE1_MEM_BASE 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */ /* controller 2, Base Address 0x9000 */ -#define CFG_PCIE2_MEM_BASE 0x90000000 -#define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE -#define CFG_PCIE2_MEM_SIZE 0x10000000 /* 256M */ -#define CFG_PCIE2_IO_BASE 0x00000000 /* reuse mem LAW */ -#define CFG_PCIE2_IO_PHYS 0xe2000000 -#define CFG_PCIE2_IO_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCIE2_MEM_BASE 0x90000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 /* reuse mem LAW */ +#define CONFIG_SYS_PCIE2_IO_PHYS 0xe2000000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00100000 /* 1M */ #if defined(CONFIG_PCI) @@ -324,11 +324,11 @@ #define CONFIG_PCI_OHCI 1 #define CONFIG_USB_OHCI_NEW 1 #define CONFIG_USB_KEYBOARD 1 -#define CFG_DEVICE_DEREGISTER -#define CFG_USB_EVENT_POLL 1 -#define CFG_USB_OHCI_SLOT_NAME "ohci_pci" -#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 -#define CFG_OHCI_SWAP_REG_ACCESS 1 +#define CONFIG_SYS_DEVICE_DEREGISTER +#define CONFIG_SYS_USB_EVENT_POLL 1 +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 +#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 #if !defined(CONFIG_PCI_PNP) #define PCI_ENET0_IOADDR 0xe0000000 @@ -341,10 +341,10 @@ #ifdef CONFIG_SCSI_AHCI #define CONFIG_SATA_ULI5288 -#define CFG_SCSI_MAX_SCSI_ID 4 -#define CFG_SCSI_MAX_LUN 1 -#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN) -#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) +#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE #endif #endif /* CONFIG_PCI */ @@ -353,10 +353,10 @@ * BAT0 2G Cacheable, non-guarded * 0x0000_0000 2G DDR */ -#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) -#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) -#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE ) -#define CFG_IBAT0U CFG_DBAT0U +#define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) +#define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE ) +#define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U /* * BAT1 1G Cache-inhibited, guarded @@ -365,22 +365,22 @@ * 0x9000_0000 256M PCI-Express 2 Memory */ -#define CFG_DBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ +#define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ | BATL_GUARDEDSTORAGE) -#define CFG_DBAT1U (CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP) -#define CFG_IBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT1U CFG_DBAT1U +#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U /* * BAT2 16M Cache-inhibited, guarded * 0xe100_0000 1M PCI-1 I/O */ -#define CFG_DBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ +#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ | BATL_GUARDEDSTORAGE) -#define CFG_DBAT2U (CFG_PCI1_IO_PHYS | BATU_BL_16M | BATU_VS | BATU_VP) -#define CFG_IBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT2U CFG_DBAT2U +#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI1_IO_PHYS | BATU_BL_16M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U /* * BAT3 32M Cache-inhibited, guarded @@ -388,68 +388,68 @@ * 0xe300_0000 1M PCI-Express 1 I/O */ -#define CFG_DBAT3L (CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ +#define CONFIG_SYS_DBAT3L (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ | BATL_GUARDEDSTORAGE) -#define CFG_DBAT3U (CFG_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP) -#define CFG_IBAT3L (CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT3U CFG_DBAT3U +#define CONFIG_SYS_DBAT3U (CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U /* * BAT4 4M Cache-inhibited, guarded * 0xe000_0000 4M CCSR */ -#define CFG_DBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \ +#define CONFIG_SYS_DBAT4L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \ | BATL_GUARDEDSTORAGE) -#define CFG_DBAT4U (CFG_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP) -#define CFG_IBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT4U CFG_DBAT4U +#define CONFIG_SYS_DBAT4U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT4L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U /* * BAT5 128K Cacheable, non-guarded * 0xe400_0000 128K Init RAM for stack in the CPU DCache (no backing memory) */ -#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) -#define CFG_IBAT5L CFG_DBAT5L -#define CFG_IBAT5U CFG_DBAT5U +#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) +#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L +#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U /* * BAT6 256M Cache-inhibited, guarded * 0xf000_0000 256M FLASH */ -#define CFG_DBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \ +#define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \ | BATL_GUARDEDSTORAGE) -#define CFG_DBAT6U (CFG_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_IBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CFG_IBAT6U CFG_DBAT6U +#define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U /* * BAT7 4M Cache-inhibited, guarded * 0xe800_0000 4M PIXIS */ -#define CFG_DBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \ +#define CONFIG_SYS_DBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \ | BATL_GUARDEDSTORAGE) -#define CFG_DBAT7U (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP) -#define CFG_IBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT7U CFG_DBAT7U +#define CONFIG_SYS_DBAT7U (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U /* * Environment */ -#ifndef CFG_RAMBOOT +#ifndef CONFIG_SYS_RAMBOOT #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) #define CONFIG_ENV_SECT_SIZE 0x20000 /* 126k (one sector) for env */ #define CONFIG_ENV_SIZE 0x2000 #else #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ -#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 #endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* @@ -470,7 +470,7 @@ #define CONFIG_CMD_I2C #define CONFIG_CMD_MII -#if defined(CFG_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) #undef CONFIG_CMD_ENV #endif @@ -483,7 +483,7 @@ #define CONFIG_WATCHDOG /* watchdog enabled */ -#define CFG_WATCHDOG_FREQ 5000 /* Feed interval, 5s */ +#define CONFIG_SYS_WATCHDOG_FREQ 5000 /* Feed interval, 5s */ /*DIU Configuration*/ #define DIU_CONNECT_TO_DVI /* DIU controller connects to DVI encoder*/ @@ -491,28 +491,28 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_CMDLINE_EDITING /* Command-line editing */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ /* * Internal Definitions |
