diff options
Diffstat (limited to 'include/configs/MPC8540EVAL.h')
| -rw-r--r-- | include/configs/MPC8540EVAL.h | 176 |
1 files changed, 88 insertions, 88 deletions
diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h index ee4f41f8ef..46a141a2c0 100644 --- a/include/configs/MPC8540EVAL.h +++ b/include/configs/MPC8540EVAL.h @@ -66,9 +66,9 @@ #define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ -#undef CFG_DRAM_TEST /* memory test, takes time */ -#define CFG_MEMTEST_START 0x00200000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00400000 +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 #if defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) #error "You can only use either PCI Ethernet Card or TSEC Ethernet, not both." @@ -78,42 +78,42 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */ -#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ -#define CFG_SDRAM_SIZE 256 /* DDR is now 256MB */ +#define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is now 256MB */ #if defined(CONFIG_RAM_AS_FLASH) -#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */ +#define CONFIG_SYS_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */ #else -#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ +#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ #endif -#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 0MB */ +#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 0MB */ #if defined(CONFIG_RAM_AS_FLASH) -#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */ -#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */ +#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH 16M */ +#define CONFIG_SYS_BR0_PRELIM 0xf8001801 /* port size 32bit */ #else /* Boot from real Flash */ -#define CFG_FLASH_BASE 0xff800000 /* start of FLASH 8M */ -#define CFG_BR0_PRELIM 0xff801001 /* port size 16bit */ +#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */ +#define CONFIG_SYS_BR0_PRELIM 0xff801001 /* port size 16bit */ #endif -#define CFG_OR0_PRELIM 0xff806f67 /* 8MB Flash */ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 64 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms)*/ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms)*/ -#define CFG_FLASH_CFI 1 +#define CONFIG_SYS_OR0_PRELIM 0xff806f67 /* 8MB Flash */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms)*/ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms)*/ +#define CONFIG_SYS_FLASH_CFI 1 -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -#define CFG_RAMBOOT +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT #else -#undef CFG_RAMBOOT +#undef CONFIG_SYS_RAMBOOT #endif /* DDR Setup */ @@ -127,8 +127,8 @@ #undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef -#define CFG_DDR_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_VERY_BIG_RAM #define CONFIG_NUM_DDR_CONTROLLERS 1 @@ -141,57 +141,57 @@ #undef CONFIG_CLOCKS_IN_MHZ /* local bus definitions */ -#define CFG_BR2_PRELIM 0xf0001861 /* 64MB localbus SDRAM */ -#define CFG_OR2_PRELIM 0xfc006901 -#define CFG_LBC_LCRR 0x00030004 /* local bus freq divider*/ -#define CFG_LBC_LBCR 0x00000000 -#define CFG_LBC_LSRT 0x20000000 -#define CFG_LBC_MRTPR 0x20000000 -#define CFG_LBC_LSDMR_1 0x2861b723 -#define CFG_LBC_LSDMR_2 0x0861b723 -#define CFG_LBC_LSDMR_3 0x0861b723 -#define CFG_LBC_LSDMR_4 0x1861b723 -#define CFG_LBC_LSDMR_5 0x4061b723 +#define CONFIG_SYS_BR2_PRELIM 0xf0001861 /* 64MB localbus SDRAM */ +#define CONFIG_SYS_OR2_PRELIM 0xfc006901 +#define CONFIG_SYS_LBC_LCRR 0x00030004 /* local bus freq divider*/ +#define CONFIG_SYS_LBC_LBCR 0x00000000 +#define CONFIG_SYS_LBC_LSRT 0x20000000 +#define CONFIG_SYS_LBC_MRTPR 0x20000000 +#define CONFIG_SYS_LBC_LSDMR_1 0x2861b723 +#define CONFIG_SYS_LBC_LSDMR_2 0x0861b723 +#define CONFIG_SYS_LBC_LSDMR_3 0x0861b723 +#define CONFIG_SYS_LBC_LSDMR_4 0x1861b723 +#define CONFIG_SYS_LBC_LSDMR_5 0x4061b723 #if defined(CONFIG_RAM_AS_FLASH) -#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */ +#define CONFIG_SYS_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */ #else -#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */ +#define CONFIG_SYS_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */ #endif -#define CFG_OR4_PRELIM 0xffffe1f1 -#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000) +#define CONFIG_SYS_OR4_PRELIM 0xffffe1f1 +#define CONFIG_SYS_BCSR (CONFIG_SYS_BR4_PRELIM & 0xffff8000) #define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 -#define CFG_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) #define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} -#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) -#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) /* Use the HUSH parser */ -#define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* @@ -200,16 +200,16 @@ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CFG_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 /* General PCI */ -#define CFG_PCI_MEM_BASE 0x80000000 -#define CFG_PCI_MEM_PHYS 0x80000000 -#define CFG_PCI_MEM_SIZE 0x20000000 -#define CFG_PCI_IO_BASE 0xe2000000 +#define CONFIG_SYS_PCI_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI_MEM_PHYS 0x80000000 +#define CONFIG_SYS_PCI_MEM_SIZE 0x20000000 +#define CONFIG_SYS_PCI_IO_BASE 0xe2000000 #if defined(CONFIG_PCI) #define CONFIG_NET_MULTI @@ -222,8 +222,8 @@ #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/ #endif #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0008 +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0008 #elif defined(CONFIG_TSEC_ENET) #define CONFIG_NET_MULTI 1 #define CONFIG_MII 1 /* MII PHY management */ @@ -254,21 +254,21 @@ #endif /* Environment */ -#ifndef CFG_RAMBOOT +#ifndef CONFIG_SYS_RAMBOOT #if defined(CONFIG_RAM_AS_FLASH) #define CONFIG_ENV_IS_NOWHERE -#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x100000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x100000) #define CONFIG_ENV_SIZE 0x2000 #else #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ #endif #define CONFIG_ENV_SIZE 0x2000 #else -/* #define CFG_NO_FLASH 1 */ /* Flash is not usable now */ +/* #define CONFIG_SYS_NO_FLASH 1 */ /* Flash is not usable now */ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ -#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 #endif @@ -277,7 +277,7 @@ #define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* @@ -301,7 +301,7 @@ #define CONFIG_CMD_PCI #endif -#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH) +#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH) #undef CONFIG_CMD_ENV #undef CONFIG_CMD_LOADS #endif @@ -312,25 +312,25 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "MPC8540EVAL=> "/* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "MPC8540EVAL=> "/* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Internal Definitions |
