diff options
Diffstat (limited to 'include/configs/MPC837XEMDS.h')
| -rw-r--r-- | include/configs/MPC837XEMDS.h | 344 |
1 files changed, 172 insertions, 172 deletions
diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 256f15665a..aeb61a9d53 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -47,7 +47,7 @@ * if CLKIN is 66MHz, then * CSB = 396MHz, CORE = 594MHz, DDRC = 396MHz, LBC = 396MHz */ -#define CFG_HRCW_LOW (\ +#define CONFIG_SYS_HRCW_LOW (\ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ HRCWL_DDR_TO_SCB_CLK_1X1 |\ HRCWL_SVCOD_DIV_2 |\ @@ -55,7 +55,7 @@ HRCWL_CORE_TO_CSB_1_5X1) #ifdef CONFIG_PCISLAVE -#define CFG_HRCW_HIGH (\ +#define CONFIG_SYS_HRCW_HIGH (\ HRCWH_PCI_AGENT |\ HRCWH_PCI1_ARBITER_DISABLE |\ HRCWH_CORE_ENABLE |\ @@ -69,7 +69,7 @@ HRCWH_BIG_ENDIAN |\ HRCWH_LDP_CLEAR) #else -#define CFG_HRCW_HIGH (\ +#define CONFIG_SYS_HRCW_HIGH (\ HRCWH_PCI_HOST |\ HRCWH_PCI1_ARBITER_ENABLE |\ HRCWH_CORE_ENABLE |\ @@ -85,29 +85,29 @@ #endif /* Arbiter Configuration Register */ -#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ -#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ /* System Priority Control Register */ -#define CFG_SPCR_TSECEP 3 /* eTSEC1/2 emergency has highest priority */ +#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC1/2 emergency has highest priority */ /* * IP blocks clock configuration */ -#define CFG_SCCR_TSEC1CM 1 /* CSB:eTSEC1 = 1:1 */ -#define CFG_SCCR_TSEC2CM 1 /* CSB:eTSEC2 = 1:1 */ -#define CFG_SCCR_SATACM SCCR_SATACM_2 /* CSB:SATA[0:3] = 2:1 */ +#define CONFIG_SYS_SCCR_TSEC1CM 1 /* CSB:eTSEC1 = 1:1 */ +#define CONFIG_SYS_SCCR_TSEC2CM 1 /* CSB:eTSEC2 = 1:1 */ +#define CONFIG_SYS_SCCR_SATACM SCCR_SATACM_2 /* CSB:SATA[0:3] = 2:1 */ /* * System IO Config */ -#define CFG_SICRH 0x00000000 -#define CFG_SICRL 0x00000000 +#define CONFIG_SYS_SICRH 0x00000000 +#define CONFIG_SYS_SICRL 0x00000000 /* * Output Buffer Impedance */ -#define CFG_OBIR 0x31100000 +#define CONFIG_SYS_OBIR 0x31100000 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ #define CONFIG_BOARD_EARLY_INIT_R @@ -115,17 +115,17 @@ /* * IMMR new address */ -#define CFG_IMMR 0xE0000000 +#define CONFIG_SYS_IMMR 0xE0000000 /* * DDR Setup */ -#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ -#define CFG_SDRAM_BASE CFG_DDR_BASE -#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE -#define CFG_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 -#define CFG_83XX_DDR_USES_CS0 -#define CFG_DDRCDR_VALUE 0x80080001 /* ODT 150ohm on SoC */ +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 +#define CONFIG_SYS_83XX_DDR_USES_CS0 +#define CONFIG_SYS_DDRCDR_VALUE 0x80080001 /* ODT 150ohm on SoC */ #undef CONFIG_DDR_ECC /* support DDR ECC function */ #undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ @@ -141,14 +141,14 @@ * WHITE ELECTRONIC DESIGNS - W3HG64M72EEU403PD4 SO-DIMM * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5 */ -#define CFG_DDR_SIZE 512 /* MB */ -#define CFG_DDR_CS0_BNDS 0x0000001f -#define CFG_DDR_CS0_CONFIG ( CSCONFIG_EN \ +#define CONFIG_SYS_DDR_SIZE 512 /* MB */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f +#define CONFIG_SYS_DDR_CS0_CONFIG ( CSCONFIG_EN \ | 0x00010000 /* ODT_WR to CSn */ \ | CSCONFIG_ROW_BIT_14 | CSCONFIG_COL_BIT_10 ) /* 0x80010202 */ -#define CFG_DDR_TIMING_3 0x00000000 -#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ | ( 0 << TIMING_CFG0_WRT_SHIFT ) \ | ( 0 << TIMING_CFG0_RRT_SHIFT ) \ | ( 0 << TIMING_CFG0_WWT_SHIFT ) \ @@ -157,7 +157,7 @@ | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \ | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) ) /* 0x00620802 */ -#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \ +#define CONFIG_SYS_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \ | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \ | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \ | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \ @@ -166,7 +166,7 @@ | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \ | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) ) /* 0x3935d322 */ -#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \ +#define CONFIG_SYS_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \ | ( 6 << TIMING_CFG2_CPO_SHIFT ) \ | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \ | ( 4 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \ @@ -174,70 +174,70 @@ | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \ | ( 8 << TIMING_CFG2_FOUR_ACT_SHIFT) ) /* 0x131088c8 */ -#define CFG_DDR_INTERVAL ( ( 0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT ) \ +#define CONFIG_SYS_DDR_INTERVAL ( ( 0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT ) \ | ( 0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) ) /* 0x03E00100 */ -#define CFG_DDR_SDRAM_CFG 0x43000000 -#define CFG_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ -#define CFG_DDR_MODE ( ( 0x0448 << SDRAM_MODE_ESD_SHIFT ) \ +#define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000 +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ +#define CONFIG_SYS_DDR_MODE ( ( 0x0448 << SDRAM_MODE_ESD_SHIFT ) \ | ( 0x1432 << SDRAM_MODE_SD_SHIFT ) ) /* ODT 150ohm CL=3, AL=1 on SDRAM */ -#define CFG_DDR_MODE2 0x00000000 +#define CONFIG_SYS_DDR_MODE2 0x00000000 #endif /* * Memory test */ -#undef CFG_DRAM_TEST /* memory test, takes time */ -#define CFG_MEMTEST_START 0x00040000 /* memtest region */ -#define CFG_MEMTEST_END 0x00140000 +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00140000 /* * The reserved memory */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -#define CFG_RAMBOOT +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT #else -#undef CFG_RAMBOOT +#undef CONFIG_SYS_RAMBOOT #endif -/* CFG_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ +/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ /* * Initial RAM Base Address Setup */ -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) /* * Local Bus Configuration & Clock Setup */ -#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_8) -#define CFG_LBC_LBCR 0x00000000 +#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_8) +#define CONFIG_SYS_LBC_LBCR 0x00000000 /* * FLASH on the Local Bus */ -#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ -#define CFG_FLASH_SIZE 32 /* max FLASH size is 32M */ -#define CFG_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CONFIG_SYS_FLASH_SIZE 32 /* max FLASH size is 32M */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ -#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ -#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */ +#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ -#define CFG_BR0_PRELIM ( CFG_FLASH_BASE /* Flash Base address */ \ +#define CONFIG_SYS_BR0_PRELIM ( CONFIG_SYS_FLASH_BASE /* Flash Base address */ \ | (2 << BR_PS_SHIFT) /* 16 bit port size */ \ | BR_V ) /* valid */ -#define CFG_OR0_PRELIM ( (~(CFG_FLASH_SIZE - 1) << 20) \ +#define CONFIG_SYS_OR0_PRELIM ( (~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \ | OR_UPM_XAM \ | OR_GPCM_CSNT \ | OR_GPCM_ACS_DIV2 \ @@ -248,33 +248,33 @@ | OR_GPCM_EAD ) /* 0xFE000FF7 */ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ /* * BCSR on the Local Bus */ -#define CFG_BCSR 0xF8000000 -#define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */ -#define CFG_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */ +#define CONFIG_SYS_BCSR 0xF8000000 +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR /* Access window base at BCSR base */ +#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */ -#define CFG_BR1_PRELIM (CFG_BCSR | 0x00000801) /* Port size=8bit, MSEL=GPCM */ -#define CFG_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR | 0x00000801) /* Port size=8bit, MSEL=GPCM */ +#define CONFIG_SYS_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ /* * NAND Flash on the Local Bus */ -#define CFG_NAND_BASE 0xE0600000 /* 0xE0600000 */ -#define CFG_BR3_PRELIM ( CFG_NAND_BASE \ +#define CONFIG_SYS_NAND_BASE 0xE0600000 /* 0xE0600000 */ +#define CONFIG_SYS_BR3_PRELIM ( CONFIG_SYS_NAND_BASE \ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V ) /* valid */ -#define CFG_OR3_PRELIM ( 0xFFFF8000 /* length 32K */ \ +#define CONFIG_SYS_OR3_PRELIM ( 0xFFFF8000 /* length 32K */ \ | OR_FCM_CSCT \ | OR_FCM_CST \ | OR_FCM_CHT \ @@ -283,29 +283,29 @@ | OR_FCM_EHTR ) /* 0xFFFF8396 */ -#define CFG_LBLAWBAR3_PRELIM CFG_NAND_BASE -#define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */ +#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000E /* 32KB */ /* * Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 -#define CFG_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} -#define CFG_NS16550_COM1 (CFG_IMMR+0x4500) -#define CFG_NS16550_COM2 (CFG_IMMR+0x4600) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) /* Use the HUSH parser */ -#define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* Pass open firmware flat tree */ @@ -317,35 +317,35 @@ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_FSL_I2C -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CFG_I2C_OFFSET 0x3000 -#define CFG_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * Config on-board RTC */ #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ -#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ /* * General PCI * Addresses are mapped 1-1. */ -#define CFG_PCI_MEM_BASE 0x80000000 -#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE -#define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */ -#define CFG_PCI_MMIO_BASE 0x90000000 -#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE -#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */ -#define CFG_PCI_IO_BASE 0x00000000 -#define CFG_PCI_IO_PHYS 0xE0300000 -#define CFG_PCI_IO_SIZE 0x100000 /* 1M */ +#define CONFIG_SYS_PCI_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE +#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 +#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE +#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 +#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */ -#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE -#define CFG_PCI_SLV_MEM_BUS 0x00000000 -#define CFG_PCI_SLV_MEM_SIZE 0x80000000 +#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 +#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 #ifdef CONFIG_PCI #define CONFIG_83XX_GENERIC_PCI 1 /* Use generic PCI setup */ @@ -356,7 +356,7 @@ #undef CONFIG_EEPRO100 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ #endif /* CONFIG_PCI */ #ifndef CONFIG_NET_MULTI @@ -367,10 +367,10 @@ * TSEC */ #define CONFIG_TSEC_ENET /* TSEC ethernet support */ -#define CFG_TSEC1_OFFSET 0x24000 -#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET) -#define CFG_TSEC2_OFFSET 0x25000 -#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET) +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 +#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) /* * TSEC ethernet configuration @@ -401,15 +401,15 @@ #define CONFIG_LIBATA #define CONFIG_FSL_SATA -#define CFG_SATA_MAX_DEVICE 2 +#define CONFIG_SYS_SATA_MAX_DEVICE 2 #define CONFIG_SATA1 -#define CFG_SATA1_OFFSET 0x18000 -#define CFG_SATA1 (CFG_IMMR + CFG_SATA1_OFFSET) -#define CFG_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SYS_SATA1_OFFSET 0x18000 +#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET) +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA #define CONFIG_SATA2 -#define CFG_SATA2_OFFSET 0x19000 -#define CFG_SATA2 (CFG_IMMR + CFG_SATA2_OFFSET) -#define CFG_SATA2_FLAGS FLAGS_DMA +#define CONFIG_SYS_SATA2_OFFSET 0x19000 +#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET) +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA #ifdef CONFIG_FSL_SATA #define CONFIG_LBA48 @@ -421,20 +421,20 @@ /* * Environment */ -#ifndef CFG_RAMBOOT +#ifndef CONFIG_SYS_RAMBOOT #define CONFIG_ENV_IS_IN_FLASH 1 - #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ #define CONFIG_ENV_SIZE 0x2000 #else - #define CFG_NO_FLASH 1 /* Flash is not usable now */ + #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 #endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* * BOOTP options @@ -459,7 +459,7 @@ #define CONFIG_CMD_PCI #endif -#if defined(CFG_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) #undef CONFIG_CMD_ENV #undef CONFIG_CMD_LOADS #endif @@ -471,34 +471,34 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) - #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else - #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup */ -#define CFG_HID0_INIT 0x000000000 -#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK -#define CFG_HID2 HID2_HBE +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK +#define CONFIG_SYS_HID2 HID2_HBE /* * MMU Setup @@ -506,67 +506,67 @@ #define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* DDR: cache cacheable */ -#define CFG_SDRAM_LOWER CFG_SDRAM_BASE -#define CFG_SDRAM_UPPER (CFG_SDRAM_BASE + 0x10000000) +#define CONFIG_SYS_SDRAM_LOWER CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_SDRAM_UPPER (CONFIG_SYS_SDRAM_BASE + 0x10000000) -#define CFG_IBAT0L (CFG_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT0U (CFG_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_DBAT0L CFG_IBAT0L -#define CFG_DBAT0U CFG_IBAT0U +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U -#define CFG_IBAT1L (CFG_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT1U (CFG_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_DBAT1L CFG_IBAT1L -#define CFG_DBAT1U CFG_IBAT1U +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ -#define CFG_IBAT2L (CFG_IMMR | BATL_PP_10 | \ +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_IMMR | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_IBAT2U (CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP) -#define CFG_DBAT2L CFG_IBAT2L -#define CFG_DBAT2U CFG_IBAT2U +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U /* BCSR: cache-inhibit and guarded */ -#define CFG_IBAT3L (CFG_BCSR | BATL_PP_10 | \ +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_BCSR | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_IBAT3U (CFG_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) -#define CFG_DBAT3L CFG_IBAT3L -#define CFG_DBAT3U CFG_IBAT3U +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U /* FLASH: icache cacheable, but dcache-inhibit and guarded */ -#define CFG_IBAT4L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT4U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) -#define CFG_DBAT4L (CFG_FLASH_BASE | BATL_PP_10 | \ +#define CONFIG_SYS_IBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT4U (CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_DBAT4U CFG_IBAT4U +#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U /* Stack in dcache: cacheable, no memory coherence */ -#define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10) -#define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) -#define CFG_DBAT5L CFG_IBAT5L -#define CFG_DBAT5U CFG_IBAT5U +#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L +#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U #ifdef CONFIG_PCI /* PCI MEM space: cacheable */ -#define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_DBAT6L CFG_IBAT6L -#define CFG_DBAT6U CFG_IBAT6U +#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U /* PCI MMIO space: cache-inhibit and guarded */ -#define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \ +#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_DBAT7L CFG_IBAT7L -#define CFG_DBAT7U CFG_IBAT7U +#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U #else -#define CFG_IBAT6L (0) -#define CFG_IBAT6U (0) -#define CFG_IBAT7L (0) -#define CFG_IBAT7U (0) -#define CFG_DBAT6L CFG_IBAT6L -#define CFG_DBAT6U CFG_IBAT6U -#define CFG_DBAT7L CFG_IBAT7L -#define CFG_DBAT7U CFG_IBAT7U +#define CONFIG_SYS_IBAT6L (0) +#define CONFIG_SYS_IBAT6U (0) +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U #endif /* |
