diff options
Diffstat (limited to 'drivers')
-rw-r--r-- | drivers/gpio/axp_gpio.c | 11 | ||||
-rw-r--r-- | drivers/mmc/Kconfig | 6 | ||||
-rw-r--r-- | drivers/power/Kconfig | 208 | ||||
-rw-r--r-- | drivers/power/axp152.c | 40 | ||||
-rw-r--r-- | drivers/power/axp209.c | 117 | ||||
-rw-r--r-- | drivers/power/axp221.c | 41 | ||||
-rw-r--r-- | drivers/usb/gadget/f_fastboot.c | 2 | ||||
-rw-r--r-- | drivers/video/sunxi_display.c | 6 |
8 files changed, 271 insertions, 160 deletions
diff --git a/drivers/gpio/axp_gpio.c b/drivers/gpio/axp_gpio.c index 2e97cc39d6..bd2ac892d0 100644 --- a/drivers/gpio/axp_gpio.c +++ b/drivers/gpio/axp_gpio.c @@ -10,22 +10,13 @@ #include <asm/arch/gpio.h> #include <asm/arch/pmic_bus.h> #include <asm/gpio.h> +#include <axp_pmic.h> #include <dm.h> #include <dm/device-internal.h> #include <dm/lists.h> #include <dm/root.h> #include <errno.h> -#ifdef CONFIG_AXP152_POWER -#include <axp152.h> -#elif defined CONFIG_AXP209_POWER -#include <axp209.h> -#elif defined CONFIG_AXP221_POWER -#include <axp221.h> -#else -#error Unknown AXP model -#endif - static int axp_gpio_set_value(struct udevice *dev, unsigned pin, int val); static u8 axp_get_gpio_ctrl_reg(unsigned pin) diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig index 6277f92ef5..ceae7bcaec 100644 --- a/drivers/mmc/Kconfig +++ b/drivers/mmc/Kconfig @@ -1,5 +1,11 @@ menu "MMC Host controller Support" +config MMC + bool "Enable MMC support" + depends on ARCH_SUNXI + help + TODO: Move all architectures to use this option + config DM_MMC bool "Enable MMC controllers using Driver Model" depends on DM diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index df5e3734b0..809f8f1180 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -4,87 +4,201 @@ source "drivers/power/pmic/Kconfig" source "drivers/power/regulator/Kconfig" +choice + prompt "Select Sunxi PMIC Variant" + depends on ARCH_SUNXI + default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I + default AXP221_POWER if MACH_SUN6I || MACH_SUN8I + +config SUNXI_NO_PMIC + boolean "board without a pmic" + ---help--- + Select this for boards which do not use a PMIC. + +config AXP152_POWER + boolean "axp152 pmic support" + depends on MACH_SUN5I + ---help--- + Select this to enable support for the axp152 pmic found on most + A10s boards. + +config AXP209_POWER + boolean "axp209 pmic support" + depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I + ---help--- + Select this to enable support for the axp209 pmic found on most + A10, A13 and A20 boards. + config AXP221_POWER boolean "axp221 / axp223 pmic support" depends on MACH_SUN6I || MACH_SUN8I - default y ---help--- - Say y here to enable support for the axp221 / axp223 pmic found on most - sun6i (A31) / sun8i (A23) boards. + Select this to enable support for the axp221/axp223 pmic found on most + A23 and A31 boards. + +endchoice + +config AXP_DCDC1_VOLT + int "axp pmic dcdc1 voltage" + depends on AXP221_POWER + default 3000 if MACH_SUN6I || MACH_SUN8I + ---help--- + Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to + disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for + generic 3.3V IO voltage for external devices like the lcd-panal and + sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to + safe battery. On A31 devices dcdc1 is also used for VCC-IO. -config AXP221_DCDC1_VOLT - int "axp221 dcdc1 voltage" +config AXP_DCDC2_VOLT + int "axp pmic dcdc2 voltage" + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER + default 1400 if AXP152_POWER || AXP209_POWER + default 1200 if MACH_SUN6I + default 1100 if MACH_SUN8I + ---help--- + Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to + disable dcdc2. + On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V. + On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V. + On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V. + +config AXP_DCDC3_VOLT + int "axp pmic dcdc3 voltage" + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER + default 1500 if AXP152_POWER + default 1250 if AXP209_POWER + default 1200 if MACH_SUN6I || MACH_SUN8I + ---help--- + Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to + disable dcdc3. + On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and + should be 1.25V. + On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V. + On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V. + +config AXP_DCDC4_VOLT + int "axp pmic dcdc4 voltage" + depends on AXP152_POWER || AXP221_POWER + default 1250 if AXP152_POWER + default 1200 if MACH_SUN6I + default 0 if MACH_SUN8I + ---help--- + Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to + disable dcdc4. + On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V. + On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V. + On A23 / A33 boards dcdc4 is unused and should be disabled. + +config AXP_DCDC5_VOLT + int "axp pmic dcdc5 voltage" depends on AXP221_POWER - default 3000 + default 1500 if MACH_SUN6I || MACH_SUN8I ---help--- - Set the voltage (mV) to program the axp221 dcdc1 at, set to 0 to - disable dcdc1. This is typically used as generic 3.3V IO voltage for - things like GPIO-s, sdcard interfaces, etc. On most boards this is - undervolted to 3.0V to safe battery. + Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to + disable dcdc5. + On A23 / A31 / A33 boards dcdc5 is VCC-DRAM and should be 1.5V. -config AXP221_DCDC2_VOLT - int "axp221 dcdc2 voltage" +config AXP_ALDO1_VOLT + int "axp pmic (a)ldo1 voltage" depends on AXP221_POWER - default 1200 + default 0 if MACH_SUN6I + default 3000 if MACH_SUN8I ---help--- - Set the voltage (mV) to program the axp221 dcdc2 at, set to 0 to - disable dcdc2. On A31 boards this is typically used for VDD-GPU, - on A23/A33 for VDD-SYS, this should normally be set to 1.2V. + Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to + disable aldo1. + On A31 boards aldo1 is often used to power the wifi module. + On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V. -config AXP221_DLDO1_VOLT - int "axp221 dldo1 voltage" +config AXP_ALDO2_VOLT + int "axp pmic (a)ldo2 voltage" + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER + default 3000 if AXP152_POWER || AXP209_POWER + default 0 if MACH_SUN6I + default 2500 if MACH_SUN8I + ---help--- + Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to + disable aldo2. + On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V. + On A31 boards aldo2 is typically unused and should be disabled. + On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V. + On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V. + +config AXP_ALDO3_VOLT + int "axp pmic (a)ldo3 voltage" + depends on AXP209_POWER || AXP221_POWER + default 0 if AXP209_POWER + default 3000 if MACH_SUN6I || MACH_SUN8I + ---help--- + Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to + disable aldo3. + On A10(s) / A13 / A20 boards aldo3 should be 2.8V. + On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V. + +config AXP_ALDO4_VOLT + int "axp pmic (a)ldo4 voltage" + depends on AXP209_POWER + default 0 if AXP209_POWER + ---help--- + Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to + disable aldo4. + On A10(s) / A13 / A20 boards aldo4 should be 2.8V. + +config AXP_DLDO1_VOLT + int "axp pmic dldo1 voltage" depends on AXP221_POWER default 0 ---help--- - Set the voltage (mV) to program the axp221 dldo1 at, set to 0 to - disable dldo1. On sun6i (A31) boards with ethernet this is often used + Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to + disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used to power the ethernet phy. On sun8i (A23) boards this is often used to power the wifi. -config AXP221_DLDO4_VOLT - int "axp221 dldo4 voltage" +config AXP_DLDO2_VOLT + int "axp pmic dldo2 voltage" depends on AXP221_POWER default 0 ---help--- - Set the voltage (mV) to program the axp221 dldo4 at, set to 0 to - disable dldo4. + Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to + disable dldo2. -config AXP221_ALDO1_VOLT - int "axp221 aldo1 voltage" +config AXP_DLDO3_VOLT + int "axp pmic dldo3 voltage" depends on AXP221_POWER default 0 ---help--- - Set the voltage (mV) to program the axp221 aldo1 at, set to 0 to - disable aldo1. On sun6i (A31) boards which have a wifi module this is - often used to power the wifi module. + Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to + disable dldo3. -config AXP221_ALDO2_VOLT - int "axp221 aldo2 voltage" +config AXP_DLDO4_VOLT + int "axp pmic dldo4 voltage" depends on AXP221_POWER - default 0 if MACH_SUN6I - default 2500 if MACH_SUN8I + default 0 ---help--- - Set the voltage (mV) to program the axp221 aldo2 at, set to 0 to - disable aldo2. On sun6i (A31) boards this is typically unused and - should be disabled, if it is used for LPDDR2 it should be set to 1.8V. - On sun8i (A23) this is typically connected to VDD-DLL and must be set - to 2.5V. + Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to + disable dldo4. -config AXP221_ALDO3_VOLT - int "axp221 aldo3 voltage" +config AXP_ELDO1_VOLT + int "axp pmic eldo1 voltage" depends on AXP221_POWER - default 3000 + default 0 + ---help--- + Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to + disable eldo1. + +config AXP_ELDO2_VOLT + int "axp pmic eldo2 voltage" + depends on AXP221_POWER + default 0 ---help--- - Set the voltage (mV) to program the axp221 aldo3 at, set to 0 to - disable aldo3. This is typically connected to VCC-PLL and AVCC and - must be set to 3V. + Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to + disable eldo2. -config AXP221_ELDO3_VOLT - int "axp221 eldo3 voltage" +config AXP_ELDO3_VOLT + int "axp pmic eldo3 voltage" depends on AXP221_POWER default 0 ---help--- - Set the voltage (mV) to program the axp221 eldo3 at, set to 0 to + Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to disable eldo3. On some A31(s) tablets it might be used to supply 1.2V for the SSD2828 chip (converter of parallel LCD interface into MIPI DSI). diff --git a/drivers/power/axp152.c b/drivers/power/axp152.c index 740a3b41cd..297258692d 100644 --- a/drivers/power/axp152.c +++ b/drivers/power/axp152.c @@ -5,18 +5,8 @@ * SPDX-License-Identifier: GPL-2.0+ */ #include <common.h> -#include <i2c.h> -#include <axp152.h> - -static int axp152_write(enum axp152_reg reg, u8 val) -{ - return i2c_write(0x30, reg, 1, &val, 1); -} - -static int axp152_read(enum axp152_reg reg, u8 *val) -{ - return i2c_read(0x30, reg, 1, val, 1); -} +#include <asm/arch/pmic_bus.h> +#include <axp_pmic.h> static u8 axp152_mvolt_to_target(int mvolt, int min, int max, int div) { @@ -28,7 +18,7 @@ static u8 axp152_mvolt_to_target(int mvolt, int min, int max, int div) return (mvolt - min) / div; } -int axp152_set_dcdc2(int mvolt) +int axp_set_dcdc2(unsigned int mvolt) { int rc; u8 current, target; @@ -36,46 +26,50 @@ int axp152_set_dcdc2(int mvolt) target = axp152_mvolt_to_target(mvolt, 700, 2275, 25); /* Do we really need to be this gentle? It has built-in voltage slope */ - while ((rc = axp152_read(AXP152_DCDC2_VOLTAGE, ¤t)) == 0 && + while ((rc = pmic_bus_read(AXP152_DCDC2_VOLTAGE, ¤t)) == 0 && current != target) { if (current < target) current++; else current--; - rc = axp152_write(AXP152_DCDC2_VOLTAGE, current); + rc = pmic_bus_write(AXP152_DCDC2_VOLTAGE, current); if (rc) break; } return rc; } -int axp152_set_dcdc3(int mvolt) +int axp_set_dcdc3(unsigned int mvolt) { u8 target = axp152_mvolt_to_target(mvolt, 700, 3500, 50); - return axp152_write(AXP152_DCDC3_VOLTAGE, target); + return pmic_bus_write(AXP152_DCDC3_VOLTAGE, target); } -int axp152_set_dcdc4(int mvolt) +int axp_set_dcdc4(unsigned int mvolt) { u8 target = axp152_mvolt_to_target(mvolt, 700, 3500, 25); - return axp152_write(AXP152_DCDC4_VOLTAGE, target); + return pmic_bus_write(AXP152_DCDC4_VOLTAGE, target); } -int axp152_set_ldo2(int mvolt) +int axp_set_aldo2(unsigned int mvolt) { u8 target = axp152_mvolt_to_target(mvolt, 700, 3500, 100); - return axp152_write(AXP152_LDO2_VOLTAGE, target); + return pmic_bus_write(AXP152_LDO2_VOLTAGE, target); } -int axp152_init(void) +int axp_init(void) { u8 ver; int rc; - rc = axp152_read(AXP152_CHIP_VERSION, &ver); + rc = pmic_bus_init(); + if (rc) + return rc; + + rc = pmic_bus_read(AXP152_CHIP_VERSION, &ver); if (rc) return rc; diff --git a/drivers/power/axp209.c b/drivers/power/axp209.c index 5161bc1472..71aa000daa 100644 --- a/drivers/power/axp209.c +++ b/drivers/power/axp209.c @@ -6,19 +6,8 @@ */ #include <common.h> -#include <i2c.h> -#include <asm/arch/gpio.h> -#include <axp209.h> - -static int axp209_write(enum axp209_reg reg, u8 val) -{ - return i2c_write(0x34, reg, 1, &val, 1); -} - -static int axp209_read(enum axp209_reg reg, u8 *val) -{ - return i2c_read(0x34, reg, 1, val, 1); -} +#include <asm/arch/pmic_bus.h> +#include <axp_pmic.h> static u8 axp209_mvolt_to_cfg(int mvolt, int min, int max, int div) { @@ -30,22 +19,30 @@ static u8 axp209_mvolt_to_cfg(int mvolt, int min, int max, int div) return (mvolt - min) / div; } -int axp209_set_dcdc2(int mvolt) +int axp_set_dcdc2(unsigned int mvolt) { int rc; u8 cfg, current; + if (mvolt == 0) + return pmic_bus_clrbits(AXP209_OUTPUT_CTRL, + AXP209_OUTPUT_CTRL_DCDC2); + + rc = pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_DCDC2); + if (rc) + return rc; + cfg = axp209_mvolt_to_cfg(mvolt, 700, 2275, 25); /* Do we really need to be this gentle? It has built-in voltage slope */ - while ((rc = axp209_read(AXP209_DCDC2_VOLTAGE, ¤t)) == 0 && + while ((rc = pmic_bus_read(AXP209_DCDC2_VOLTAGE, ¤t)) == 0 && current != cfg) { if (current < cfg) current++; else current--; - rc = axp209_write(AXP209_DCDC2_VOLTAGE, current); + rc = pmic_bus_write(AXP209_DCDC2_VOLTAGE, current); if (rc) break; } @@ -53,68 +50,106 @@ int axp209_set_dcdc2(int mvolt) return rc; } -int axp209_set_dcdc3(int mvolt) +int axp_set_dcdc3(unsigned int mvolt) { u8 cfg = axp209_mvolt_to_cfg(mvolt, 700, 3500, 25); + int rc; - return axp209_write(AXP209_DCDC3_VOLTAGE, cfg); + if (mvolt == 0) + return pmic_bus_clrbits(AXP209_OUTPUT_CTRL, + AXP209_OUTPUT_CTRL_DCDC3); + + rc = pmic_bus_write(AXP209_DCDC3_VOLTAGE, cfg); + if (rc) + return rc; + + return pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_DCDC3); } -int axp209_set_ldo2(int mvolt) +int axp_set_aldo2(unsigned int mvolt) { int rc; u8 cfg, reg; + if (mvolt == 0) + return pmic_bus_clrbits(AXP209_OUTPUT_CTRL, + AXP209_OUTPUT_CTRL_LDO2); + cfg = axp209_mvolt_to_cfg(mvolt, 1800, 3300, 100); - rc = axp209_read(AXP209_LDO24_VOLTAGE, ®); + rc = pmic_bus_read(AXP209_LDO24_VOLTAGE, ®); if (rc) return rc; /* LDO2 configuration is in upper 4 bits */ reg = (reg & 0x0f) | (cfg << 4); - return axp209_write(AXP209_LDO24_VOLTAGE, reg); + rc = pmic_bus_write(AXP209_LDO24_VOLTAGE, reg); + if (rc) + return rc; + + return pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_LDO2); } -int axp209_set_ldo3(int mvolt) +int axp_set_aldo3(unsigned int mvolt) { u8 cfg; + int rc; + + if (mvolt == 0) + return pmic_bus_clrbits(AXP209_OUTPUT_CTRL, + AXP209_OUTPUT_CTRL_LDO3); if (mvolt == -1) cfg = 0x80; /* determined by LDO3IN pin */ else cfg = axp209_mvolt_to_cfg(mvolt, 700, 3500, 25); - return axp209_write(AXP209_LDO3_VOLTAGE, cfg); + rc = pmic_bus_write(AXP209_LDO3_VOLTAGE, cfg); + if (rc) + return rc; + + return pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_LDO3); } -int axp209_set_ldo4(int mvolt) +int axp_set_aldo4(unsigned int mvolt) { int rc; - static const int vindex[] = { + static const unsigned int vindex[] = { 1250, 1300, 1400, 1500, 1600, 1700, 1800, 1900, 2000, 2500, 2700, 2800, 3000, 3100, 3200, 3300 }; u8 cfg, reg; + if (mvolt == 0) + return pmic_bus_clrbits(AXP209_OUTPUT_CTRL, + AXP209_OUTPUT_CTRL_LDO4); + /* Translate mvolt to register cfg value, requested <= selected */ for (cfg = 15; vindex[cfg] > mvolt && cfg > 0; cfg--); - rc = axp209_read(AXP209_LDO24_VOLTAGE, ®); + rc = pmic_bus_read(AXP209_LDO24_VOLTAGE, ®); if (rc) return rc; /* LDO4 configuration is in lower 4 bits */ reg = (reg & 0xf0) | (cfg << 0); - return axp209_write(AXP209_LDO24_VOLTAGE, reg); + rc = pmic_bus_write(AXP209_LDO24_VOLTAGE, reg); + if (rc) + return rc; + + return pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_LDO4); } -int axp209_init(void) +int axp_init(void) { u8 ver; int i, rc; - rc = axp209_read(AXP209_CHIP_VERSION, &ver); + rc = pmic_bus_init(); + if (rc) + return rc; + + rc = pmic_bus_read(AXP209_CHIP_VERSION, &ver); if (rc) return rc; @@ -126,32 +161,10 @@ int axp209_init(void) /* Mask all interrupts */ for (i = AXP209_IRQ_ENABLE1; i <= AXP209_IRQ_ENABLE5; i++) { - rc = axp209_write(i, 0); + rc = pmic_bus_write(i, 0); if (rc) return rc; } return 0; } - -int axp209_poweron_by_dc(void) -{ - u8 v; - - if (axp209_read(AXP209_POWER_STATUS, &v)) - return 0; - - return (v & AXP209_POWER_STATUS_ON_BY_DC); -} - -int axp209_power_button(void) -{ - u8 v; - - if (axp209_read(AXP209_IRQ_STATUS5, &v)) - return 0; - - axp209_write(AXP209_IRQ_STATUS5, AXP209_IRQ5_PEK_DOWN); - - return v & AXP209_IRQ5_PEK_DOWN; -} diff --git a/drivers/power/axp221.c b/drivers/power/axp221.c index 7bbaec87e4..65802e4a71 100644 --- a/drivers/power/axp221.c +++ b/drivers/power/axp221.c @@ -12,9 +12,8 @@ #include <common.h> #include <errno.h> -#include <asm/arch/gpio.h> #include <asm/arch/pmic_bus.h> -#include <axp221.h> +#include <axp_pmic.h> static u8 axp221_mvolt_to_cfg(int mvolt, int min, int max, int div) { @@ -26,7 +25,7 @@ static u8 axp221_mvolt_to_cfg(int mvolt, int min, int max, int div) return (mvolt - min) / div; } -int axp221_set_dcdc1(unsigned int mvolt) +int axp_set_dcdc1(unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 1600, 3400, 100); @@ -48,7 +47,7 @@ int axp221_set_dcdc1(unsigned int mvolt) AXP221_OUTPUT_CTRL1_DCDC1_EN); } -int axp221_set_dcdc2(unsigned int mvolt) +int axp_set_dcdc2(unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 600, 1540, 20); @@ -65,7 +64,7 @@ int axp221_set_dcdc2(unsigned int mvolt) AXP221_OUTPUT_CTRL1_DCDC2_EN); } -int axp221_set_dcdc3(unsigned int mvolt) +int axp_set_dcdc3(unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 600, 1860, 20); @@ -82,7 +81,7 @@ int axp221_set_dcdc3(unsigned int mvolt) AXP221_OUTPUT_CTRL1_DCDC3_EN); } -int axp221_set_dcdc4(unsigned int mvolt) +int axp_set_dcdc4(unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 600, 1540, 20); @@ -99,7 +98,7 @@ int axp221_set_dcdc4(unsigned int mvolt) AXP221_OUTPUT_CTRL1_DCDC4_EN); } -int axp221_set_dcdc5(unsigned int mvolt) +int axp_set_dcdc5(unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 1000, 2550, 50); @@ -116,7 +115,7 @@ int axp221_set_dcdc5(unsigned int mvolt) AXP221_OUTPUT_CTRL1_DCDC5_EN); } -int axp221_set_dldo1(unsigned int mvolt) +int axp_set_dldo1(unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100); @@ -133,7 +132,7 @@ int axp221_set_dldo1(unsigned int mvolt) AXP221_OUTPUT_CTRL2_DLDO1_EN); } -int axp221_set_dldo2(unsigned int mvolt) +int axp_set_dldo2(unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100); @@ -150,7 +149,7 @@ int axp221_set_dldo2(unsigned int mvolt) AXP221_OUTPUT_CTRL2_DLDO2_EN); } -int axp221_set_dldo3(unsigned int mvolt) +int axp_set_dldo3(unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100); @@ -167,7 +166,7 @@ int axp221_set_dldo3(unsigned int mvolt) AXP221_OUTPUT_CTRL2_DLDO3_EN); } -int axp221_set_dldo4(unsigned int mvolt) +int axp_set_dldo4(unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100); @@ -184,7 +183,7 @@ int axp221_set_dldo4(unsigned int mvolt) AXP221_OUTPUT_CTRL2_DLDO4_EN); } -int axp221_set_aldo1(unsigned int mvolt) +int axp_set_aldo1(unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100); @@ -201,7 +200,7 @@ int axp221_set_aldo1(unsigned int mvolt) AXP221_OUTPUT_CTRL1_ALDO1_EN); } -int axp221_set_aldo2(unsigned int mvolt) +int axp_set_aldo2(unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100); @@ -218,7 +217,7 @@ int axp221_set_aldo2(unsigned int mvolt) AXP221_OUTPUT_CTRL1_ALDO2_EN); } -int axp221_set_aldo3(unsigned int mvolt) +int axp_set_aldo3(unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100); @@ -235,7 +234,7 @@ int axp221_set_aldo3(unsigned int mvolt) AXP221_OUTPUT_CTRL3_ALDO3_EN); } -int axp221_set_eldo(int eldo_num, unsigned int mvolt) +int axp_set_eldo(int eldo_num, unsigned int mvolt) { int ret; u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100); @@ -268,16 +267,11 @@ int axp221_set_eldo(int eldo_num, unsigned int mvolt) return pmic_bus_setbits(AXP221_OUTPUT_CTRL2, bits); } -int axp221_init(void) +int axp_init(void) { - /* This cannot be 0 because it is used in SPL before BSS is ready */ - static int needs_init = 1; u8 axp_chip_id; int ret; - if (!needs_init) - return 0; - ret = pmic_bus_init(); if (ret) return ret; @@ -289,16 +283,15 @@ int axp221_init(void) if (!(axp_chip_id == 0x6 || axp_chip_id == 0x7 || axp_chip_id == 0x17)) return -ENODEV; - needs_init = 0; return 0; } -int axp221_get_sid(unsigned int *sid) +int axp_get_sid(unsigned int *sid) { u8 *dest = (u8 *)sid; int i, ret; - ret = axp221_init(); + ret = pmic_bus_init(); if (ret) return ret; diff --git a/drivers/usb/gadget/f_fastboot.c b/drivers/usb/gadget/f_fastboot.c index ca01a018b5..ece48e668c 100644 --- a/drivers/usb/gadget/f_fastboot.c +++ b/drivers/usb/gadget/f_fastboot.c @@ -554,7 +554,7 @@ static void cb_flash(struct usb_ep *ep, struct usb_request *req) static void cb_oem(struct usb_ep *ep, struct usb_request *req) { char *cmd = req->buf; -#ifdef CONFIG_FASTBOOT_FLASH +#ifdef CONFIG_FASTBOOT_FLASH_MMC_DEV if (strncmp("format", cmd + 4, 6) == 0) { char cmdbuf[32]; sprintf(cmdbuf, "gpt write mmc %x $partitions", diff --git a/drivers/video/sunxi_display.c b/drivers/video/sunxi_display.c index fc1aea3f06..9fee66a2a4 100644 --- a/drivers/video/sunxi_display.c +++ b/drivers/video/sunxi_display.c @@ -15,7 +15,7 @@ #include <asm/global_data.h> #include <asm/gpio.h> #include <asm/io.h> -#include <axp221.h> +#include <axp_pmic.h> #include <errno.h> #include <fdtdec.h> #include <fdt_support.h> @@ -1217,10 +1217,10 @@ static void sunxi_mode_set(const struct ctfb_res_modes *mode, if (IS_ENABLED(CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804)) { /* * The anx9804 needs 1.8V from eldo3, we do this here - * and not via CONFIG_AXP221_ELDO3 from board_init() + * and not via CONFIG_AXP_ELDO3_VOLT from board_init() * to avoid turning this on when using hdmi output. */ - axp221_set_eldo(3, 1800); + axp_set_eldo(3, 1800); anx9804_init(CONFIG_VIDEO_LCD_I2C_BUS, 4, ANX9804_DATA_RATE_1620M, sunxi_display.depth); |