summaryrefslogtreecommitdiffstats
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/video/Makefile1
-rw-r--r--drivers/video/parade.c231
2 files changed, 0 insertions, 232 deletions
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 599fe83b33..c2c4dfc57e 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -51,7 +51,6 @@ obj-$(CONFIG_VIDEO_VESA) += vesa_fb.o
obj-$(CONFIG_FORMIKE) += formike.o
obj-$(CONFIG_LG4573) += lg4573.o
obj-$(CONFIG_AM335X_LCD) += am335x-fb.o
-obj-$(CONFIG_VIDEO_PARADE) += parade.o
obj-${CONFIG_VIDEO_TEGRA124} += tegra124/
diff --git a/drivers/video/parade.c b/drivers/video/parade.c
deleted file mode 100644
index ae5097160f..0000000000
--- a/drivers/video/parade.c
+++ /dev/null
@@ -1,231 +0,0 @@
-/*
- * Copyright (c) 2014 The Chromium OS Authors. All rights reserved.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * This file is a driver for Parade dP<->LVDS bridges. The original submission
- * is for the ps8625 chip.
- */
-#include <config.h>
-#include <common.h>
-#include <i2c.h>
-#include <fdtdec.h>
-#include <asm/gpio.h>
-
-/*
- * Initialization of the chip is a process of writing certaing values into
- * certain registers over i2c bus. The chip in fact responds to a range of
- * addresses on the i2c bus, so for each written value three parameters are
- * required: i2c address, register address and the actual value.
- *
- * The base address is derived from the device tree, only address offset is
- * stored in the table below.
- */
-/**
- * struct reg_data() - data for a parade register write
- *
- * @addr_off offset from the i2c base address for parade
- * @reg_addr register address to write
- * @value value to be written
- */
-struct reg_data {
- uint8_t addr_off;
- uint8_t reg;
- uint8_t value;
-} _packed;
-
-#define END_OF_TABLE 0xff /* Ficticious offset */
-
-static const struct reg_data parade_values[] = {
- {0x02, 0xa1, 0x01}, /* HPD low */
- /*
- * SW setting
- * [1:0] SW output 1.2V voltage is lower to 96%
- */
- {0x04, 0x14, 0x01},
- /*
- * RCO SS setting
- * [5:4] = b01 0.5%, b10 1%, b11 1.5%
- */
- {0x04, 0xe3, 0x20},
- {0x04, 0xe2, 0x80}, /* [7] RCO SS enable */
- /*
- * RPHY Setting
- * [3:2] CDR tune wait cycle before
- * measure for fine tune b00: 1us,
- * 01: 0.5us, 10:2us, 11:4us.
- */
- {0x04, 0x8a, 0x0c},
- {0x04, 0x89, 0x08}, /* [3] RFD always on */
- /*
- * CTN lock in/out:
- * 20000ppm/80000ppm. Lock out 2
- * times.
- */
- {0x04, 0x71, 0x2d},
- /*
- * 2.7G CDR settings
- * NOF=40LSB for HBR CDR setting
- */
- {0x04, 0x7d, 0x07},
- {0x04, 0x7b, 0x00}, /* [1:0] Fmin=+4bands */
- {0x04, 0x7a, 0xfd}, /* [7:5] DCO_FTRNG=+-40% */
- /*
- * 1.62G CDR settings
- * [5:2]NOF=64LSB [1:0]DCO scale is 2/5
- */
- {0x04, 0xc0, 0x12},
- {0x04, 0xc1, 0x92}, /* Gitune=-37% */
- {0x04, 0xc2, 0x1c}, /* Fbstep=100% */
- {0x04, 0x32, 0x80}, /* [7] LOS signal disable */
- /*
- * RPIO Setting
- * [7:4] LVDS driver bias current :
- * 75% (250mV swing)
- */
- {0x04, 0x00, 0xb0},
- /*
- * [7:6] Right-bar GPIO output strength is 8mA
- */
- {0x04, 0x15, 0x40},
- /* EQ Training State Machine Setting */
- {0x04, 0x54, 0x10}, /* RCO calibration start */
- /* [4:0] MAX_LANE_COUNT set to one lane */
- {0x01, 0x02, 0x81},
- /* [4:0] LANE_COUNT_SET set to one lane */
- {0x01, 0x21, 0x81},
- {0x00, 0x52, 0x20},
- {0x00, 0xf1, 0x03}, /* HPD CP toggle enable */
- {0x00, 0x62, 0x41},
- /* Counter number, add 1ms counter delay */
- {0x00, 0xf6, 0x01},
- /*
- * [6]PWM function control by
- * DPCD0040f[7], default is PWM
- * block always works.
- */
- {0x00, 0x77, 0x06},
- /*
- * 04h Adjust VTotal tolerance to
- * fix the 30Hz no display issue
- */
- {0x00, 0x4c, 0x04},
- /* DPCD00400='h00, Parade OUI = 'h001cf8 */
- {0x01, 0xc0, 0x00},
- {0x01, 0xc1, 0x1c}, /* DPCD00401='h1c */
- {0x01, 0xc2, 0xf8}, /* DPCD00402='hf8 */
- /*
- * DPCD403~408 = ASCII code
- * D2SLV5='h4432534c5635
- */
- {0x01, 0xc3, 0x44},
- {0x01, 0xc4, 0x32}, /* DPCD404 */
- {0x01, 0xc5, 0x53}, /* DPCD405 */
- {0x01, 0xc6, 0x4c}, /* DPCD406 */
- {0x01, 0xc7, 0x56}, /* DPCD407 */
- {0x01, 0xc8, 0x35}, /* DPCD408 */
- /*
- * DPCD40A, Initial Code major revision
- * '01'
- */
- {0x01, 0xca, 0x01},
- /* DPCD40B, Initial Code minor revision '05' */
- {0x01, 0xcb, 0x05},
- /* DPCD720, Select internal PWM */
- {0x01, 0xa5, 0xa0},
- /*
- * FFh for 100% PWM of brightness, 0h for 0%
- * brightness
- */
- {0x01, 0xa7, 0xff},
- /*
- * Set LVDS output as 6bit-VESA mapping,
- * single LVDS channel
- */
- {0x01, 0xcc, 0x13},
- /* Enable SSC set by register */
- {0x02, 0xb1, 0x20},
- /*
- * Set SSC enabled and +/-1% central
- * spreading
- */
- {0x04, 0x10, 0x16},
- /* MPU Clock source: LC => RCO */
- {0x04, 0x59, 0x60},
- {0x04, 0x54, 0x14}, /* LC -> RCO */
- {0x02, 0xa1, 0x91}, /* HPD high */
- {END_OF_TABLE}
-};
-
-/**
- * Write values table into the Parade eDP bridge
- *
- * @return 0 on success, non-0 on failure
- */
-
-static int parade_write_regs(int base_addr, const struct reg_data *table)
-{
- int ret = 0;
-
- while (!ret && (table->addr_off != END_OF_TABLE)) {
- ret = i2c_write(base_addr + table->addr_off,
- table->reg, 1,
- (uint8_t *)&table->value,
- sizeof(table->value));
- table++;
- }
- return ret;
-}
-
-int parade_init(const void *blob)
-{
- struct gpio_desc rst_gpio;
- struct gpio_desc slp_gpio;
- int bus, old_bus;
- int parent;
- int node;
- int addr;
- int ret;
-
- node = fdtdec_next_compatible(blob, 0, COMPAT_PARADE_PS8625);
- if (node < 0)
- return 0;
-
- parent = fdt_parent_offset(blob, node);
- if (parent < 0) {
- debug("%s: Could not find parent i2c node\n", __func__);
- return -1;
- }
- addr = fdtdec_get_int(blob, node, "reg", -1);
- if (addr < 0) {
- debug("%s: Could not find i2c address\n", __func__);
- return -1;
- }
-
- gpio_request_by_name_nodev(blob, node, "sleep-gpio", 0, &slp_gpio,
- GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
-
- mdelay(10);
-
- gpio_request_by_name_nodev(blob, node, "reset-gpio", 0, &rst_gpio,
- GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
-
- bus = i2c_get_bus_num_fdt(parent);
- old_bus = i2c_get_bus_num();
-
- debug("%s: Using i2c bus %d\n", __func__, bus);
-
- /*
- * TODO(sjg@chromium.org): Hmmm we seem to need some sort of delay
- * here.
- */
- mdelay(40);
- i2c_set_bus_num(bus);
- ret = parade_write_regs(addr, parade_values);
-
- i2c_set_bus_num(old_bus);
-
- return ret;
-}
OpenPOWER on IntegriCloud