diff options
Diffstat (limited to 'drivers/3c589.h')
| -rw-r--r-- | drivers/3c589.h | 435 |
1 files changed, 435 insertions, 0 deletions
diff --git a/drivers/3c589.h b/drivers/3c589.h new file mode 100644 index 0000000000..00e7f7c30f --- /dev/null +++ b/drivers/3c589.h @@ -0,0 +1,435 @@ +/* + * Copyright (c) 1993 Herb Peyerl (hpeyerl@novatel.ca) All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are + * met: 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. 2. The name + * of the author may not be used to endorse or promote products derived from + * this software without specific prior written permission + * + * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO + * EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED + * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR + * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF + * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING + * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + October 2, 1994 + + Modified by: Andres Vega Garcia + + INRIA - Sophia Antipolis, France + e-mail: avega@sophia.inria.fr + finger: avega@pax.inria.fr + + */ + +/* + * Created from if_epreg.h by Fred Gray (fgray@rice.edu) to support the + * 3c590 family. + */ + +/* + * Modified by Shusuke Nisiyama <shu@athena.qe.eng.hokudai.ac.jp> + * for etherboot + * Mar. 14, 2000 +*/ + +/* + * Ethernet software status per interface. + */ + +/* + * Some global constants + */ + +#define TX_INIT_RATE 16 +#define TX_INIT_MAX_RATE 64 +#define RX_INIT_LATENCY 64 +#define RX_INIT_EARLY_THRESH 64 +#define MIN_RX_EARLY_THRESHF 16 /* not less than ether_header */ +#define MIN_RX_EARLY_THRESHL 4 + +#define EEPROMSIZE 0x40 +#define MAX_EEPROMBUSY 1000 +#define VX_LAST_TAG 0xd7 +#define VX_MAX_BOARDS 16 +#define VX_ID_PORT 0x100 + +/* + * some macros to acces long named fields + */ +#define BASE (EL_BASE_ADDR) + +/* + * Commands to read/write EEPROM trough EEPROM command register (Window 0, + * Offset 0xa) + */ +#define EEPROM_CMD_RD 0x0080 /* Read: Address required (5 bits) */ +#define EEPROM_CMD_WR 0x0040 /* Write: Address required (5 bits) */ +#define EEPROM_CMD_ERASE 0x00c0 /* Erase: Address required (5 bits) */ +#define EEPROM_CMD_EWEN 0x0030 /* Erase/Write Enable: No data required */ + +#define EEPROM_BUSY (1<<15) + +/* + * Some short functions, worth to let them be a macro + */ + +/************************************************************************** + * * + * These define the EEPROM data structure. They are used in the probe + * function to verify the existence of the adapter after having sent + * the ID_Sequence. + * + * There are others but only the ones we use are defined here. + * + **************************************************************************/ + +#define EEPROM_NODE_ADDR_0 0x0 /* Word */ +#define EEPROM_NODE_ADDR_1 0x1 /* Word */ +#define EEPROM_NODE_ADDR_2 0x2 /* Word */ +#define EEPROM_PROD_ID 0x3 /* 0x9[0-f]50 */ +#define EEPROM_MFG_ID 0x7 /* 0x6d50 */ +#define EEPROM_ADDR_CFG 0x8 /* Base addr */ +#define EEPROM_RESOURCE_CFG 0x9 /* IRQ. Bits 12-15 */ +#define EEPROM_OEM_ADDR_0 0xa /* Word */ +#define EEPROM_OEM_ADDR_1 0xb /* Word */ +#define EEPROM_OEM_ADDR_2 0xc /* Word */ +#define EEPROM_SOFT_INFO_2 0xf /* Software information 2 */ + +#define NO_RX_OVN_ANOMALY (1<<5) + +/************************************************************************** + * * + * These are the registers for the 3Com 3c509 and their bit patterns when * + * applicable. They have been taken out the the "EtherLink III Parallel * + * Tasking EISA and ISA Technical Reference" "Beta Draft 10/30/92" manual * + * from 3com. * + * * + **************************************************************************/ + +#define VX_COMMAND 0x0e /* Write. BASE+0x0e is always a + * command reg. */ +#define VX_STATUS 0x0e /* Read. BASE+0x0e is always status + * reg. */ +#define VX_WINDOW 0x0f /* Read. BASE+0x0f is always window + * reg. */ +/* + * Window 0 registers. Setup. + */ +/* Write */ +#define VX_W0_EEPROM_DATA 0x0c +#define VX_W0_EEPROM_COMMAND 0x0a +#define VX_W0_RESOURCE_CFG 0x08 +#define VX_W0_ADDRESS_CFG 0x06 +#define VX_W0_CONFIG_CTRL 0x04 + /* Read */ +#define VX_W0_PRODUCT_ID 0x02 +#define VX_W0_MFG_ID 0x00 + + +/* + * Window 1 registers. Operating Set. + */ +/* Write */ +#define VX_W1_TX_PIO_WR_2 0x02 +#define VX_W1_TX_PIO_WR_1 0x00 +/* Read */ +#define VX_W1_FREE_TX 0x0c +#define VX_W1_TX_STATUS 0x0b /* byte */ +#define VX_W1_TIMER 0x0a /* byte */ +#define VX_W1_RX_STATUS 0x08 +#define VX_W1_RX_PIO_RD_2 0x02 +#define VX_W1_RX_PIO_RD_1 0x00 + +/* + * Window 2 registers. Station Address Setup/Read + */ +/* Read/Write */ +#define VX_W2_ADDR_5 0x05 +#define VX_W2_ADDR_4 0x04 +#define VX_W2_ADDR_3 0x03 +#define VX_W2_ADDR_2 0x02 +#define VX_W2_ADDR_1 0x01 +#define VX_W2_ADDR_0 0x00 + +/* + * Window 3 registers. FIFO Management. + */ +/* Read */ +#define VX_W3_INTERNAL_CFG 0x00 +#define VX_W3_RESET_OPT 0x08 +#define VX_W3_FREE_TX 0x0c +#define VX_W3_FREE_RX 0x0a + +/* + * Window 4 registers. Diagnostics. + */ +/* Read/Write */ +#define VX_W4_MEDIA_TYPE 0x0a +#define VX_W4_CTRLR_STATUS 0x08 +#define VX_W4_NET_DIAG 0x06 +#define VX_W4_FIFO_DIAG 0x04 +#define VX_W4_HOST_DIAG 0x02 +#define VX_W4_TX_DIAG 0x00 + +/* + * Window 5 Registers. Results and Internal status. + */ +/* Read */ +#define VX_W5_READ_0_MASK 0x0c +#define VX_W5_INTR_MASK 0x0a +#define VX_W5_RX_FILTER 0x08 +#define VX_W5_RX_EARLY_THRESH 0x06 +#define VX_W5_TX_AVAIL_THRESH 0x02 +#define VX_W5_TX_START_THRESH 0x00 + +/* + * Window 6 registers. Statistics. + */ +/* Read/Write */ +#define TX_TOTAL_OK 0x0c +#define RX_TOTAL_OK 0x0a +#define TX_DEFERRALS 0x08 +#define RX_FRAMES_OK 0x07 +#define TX_FRAMES_OK 0x06 +#define RX_OVERRUNS 0x05 +#define TX_COLLISIONS 0x04 +#define TX_AFTER_1_COLLISION 0x03 +#define TX_AFTER_X_COLLISIONS 0x02 +#define TX_NO_SQE 0x01 +#define TX_CD_LOST 0x00 + +/**************************************** + * + * Register definitions. + * + ****************************************/ + +/* + * Command register. All windows. + * + * 16 bit register. + * 15-11: 5-bit code for command to be executed. + * 10-0: 11-bit arg if any. For commands with no args; + * this can be set to anything. + */ +#define GLOBAL_RESET (unsigned short) 0x0000 /* Wait at least 1ms + * after issuing */ +#define WINDOW_SELECT (unsigned short) (0x1<<11) +#define START_TRANSCEIVER (unsigned short) (0x2<<11) /* Read ADDR_CFG reg to + * determine whether + * this is needed. If + * so; wait 800 uSec + * before using trans- + * ceiver. */ +#define RX_DISABLE (unsigned short) (0x3<<11) /* state disabled on + * power-up */ +#define RX_ENABLE (unsigned short) (0x4<<11) +#define RX_RESET (unsigned short) (0x5<<11) +#define RX_DISCARD_TOP_PACK (unsigned short) (0x8<<11) +#define TX_ENABLE (unsigned short) (0x9<<11) +#define TX_DISABLE (unsigned short) (0xa<<11) +#define TX_RESET (unsigned short) (0xb<<11) +#define REQ_INTR (unsigned short) (0xc<<11) +/* + * The following C_* acknowledge the various interrupts. Some of them don't + * do anything. See the manual. + */ +#define ACK_INTR (unsigned short) (0x6800) +# define C_INTR_LATCH (unsigned short) (ACK_INTR|0x1) +# define C_CARD_FAILURE (unsigned short) (ACK_INTR|0x2) +# define C_TX_COMPLETE (unsigned short) (ACK_INTR|0x4) +# define C_TX_AVAIL (unsigned short) (ACK_INTR|0x8) +# define C_RX_COMPLETE (unsigned short) (ACK_INTR|0x10) +# define C_RX_EARLY (unsigned short) (ACK_INTR|0x20) +# define C_INT_RQD (unsigned short) (ACK_INTR|0x40) +# define C_UPD_STATS (unsigned short) (ACK_INTR|0x80) +#define SET_INTR_MASK (unsigned short) (0xe<<11) +#define SET_RD_0_MASK (unsigned short) (0xf<<11) +#define SET_RX_FILTER (unsigned short) (0x10<<11) +# define FIL_INDIVIDUAL (unsigned short) (0x1) +# define FIL_MULTICAST (unsigned short) (0x02) +# define FIL_BRDCST (unsigned short) (0x04) +# define FIL_PROMISC (unsigned short) (0x08) +#define SET_RX_EARLY_THRESH (unsigned short) (0x11<<11) +#define SET_TX_AVAIL_THRESH (unsigned short) (0x12<<11) +#define SET_TX_START_THRESH (unsigned short) (0x13<<11) +#define STATS_ENABLE (unsigned short) (0x15<<11) +#define STATS_DISABLE (unsigned short) (0x16<<11) +#define STOP_TRANSCEIVER (unsigned short) (0x17<<11) + +/* + * Status register. All windows. + * + * 15-13: Window number(0-7). + * 12: Command_in_progress. + * 11: reserved. + * 10: reserved. + * 9: reserved. + * 8: reserved. + * 7: Update Statistics. + * 6: Interrupt Requested. + * 5: RX Early. + * 4: RX Complete. + * 3: TX Available. + * 2: TX Complete. + * 1: Adapter Failure. + * 0: Interrupt Latch. + */ +#define S_INTR_LATCH (unsigned short) (0x1) +#define S_CARD_FAILURE (unsigned short) (0x2) +#define S_TX_COMPLETE (unsigned short) (0x4) +#define S_TX_AVAIL (unsigned short) (0x8) +#define S_RX_COMPLETE (unsigned short) (0x10) +#define S_RX_EARLY (unsigned short) (0x20) +#define S_INT_RQD (unsigned short) (0x40) +#define S_UPD_STATS (unsigned short) (0x80) +#define S_COMMAND_IN_PROGRESS (unsigned short) (0x1000) + +#define VX_BUSY_WAIT while (inw(BASE + VX_STATUS) & S_COMMAND_IN_PROGRESS) + +/* Address Config. Register. + * Window 0/Port 06 + */ + +#define ACF_CONNECTOR_BITS 14 +#define ACF_CONNECTOR_UTP 0 +#define ACF_CONNECTOR_AUI 1 +#define ACF_CONNECTOR_BNC 3 + +#define INTERNAL_CONNECTOR_BITS 20 +#define INTERNAL_CONNECTOR_MASK 0x01700000 + +/* + * FIFO Registers. RX Status. + * + * 15: Incomplete or FIFO empty. + * 14: 1: Error in RX Packet 0: Incomplete or no error. + * 13-11: Type of error. + * 1000 = Overrun. + * 1011 = Run Packet Error. + * 1100 = Alignment Error. + * 1101 = CRC Error. + * 1001 = Oversize Packet Error (>1514 bytes) + * 0010 = Dribble Bits. + * (all other error codes, no errors.) + * + * 10-0: RX Bytes (0-1514) + */ +#define ERR_INCOMPLETE (unsigned short) (0x8000) +#define ERR_RX (unsigned short) (0x4000) +#define ERR_MASK (unsigned short) (0x7800) +#define ERR_OVERRUN (unsigned short) (0x4000) +#define ERR_RUNT (unsigned short) (0x5800) +#define ERR_ALIGNMENT (unsigned short) (0x6000) +#define ERR_CRC (unsigned short) (0x6800) +#define ERR_OVERSIZE (unsigned short) (0x4800) +#define ERR_DRIBBLE (unsigned short) (0x1000) + +/* + * TX Status. + * + * Reports the transmit status of a completed transmission. Writing this + * register pops the transmit completion stack. + * + * Window 1/Port 0x0b. + * + * 7: Complete + * 6: Interrupt on successful transmission requested. + * 5: Jabber Error (TP Only, TX Reset required. ) + * 4: Underrun (TX Reset required. ) + * 3: Maximum Collisions. + * 2: TX Status Overflow. + * 1-0: Undefined. + * + */ +#define TXS_COMPLETE 0x80 +#define TXS_INTR_REQ 0x40 +#define TXS_JABBER 0x20 +#define TXS_UNDERRUN 0x10 +#define TXS_MAX_COLLISION 0x8 +#define TXS_STATUS_OVERFLOW 0x4 + +#define RS_AUI (1<<5) +#define RS_BNC (1<<4) +#define RS_UTP (1<<3) +#define RS_T4 (1<<0) +#define RS_TX (1<<1) +#define RS_FX (1<<2) +#define RS_MII (1<<6) + + +/* + * FIFO Status (Window 4) + * + * Supports FIFO diagnostics + * + * Window 4/Port 0x04.1 + * + * 15: 1=RX receiving (RO). Set when a packet is being received + * into the RX FIFO. + * 14: Reserved + * 13: 1=RX underrun (RO). Generates Adapter Failure interrupt. + * Requires RX Reset or Global Reset command to recover. + * It is generated when you read past the end of a packet - + * reading past what has been received so far will give bad + * data. + * 12: 1=RX status overrun (RO). Set when there are already 8 + * packets in the RX FIFO. While this bit is set, no additional + * packets are received. Requires no action on the part of + * the host. The condition is cleared once a packet has been + * read out of the RX FIFO. + * 11: 1=RX overrun (RO). Set when the RX FIFO is full (there + * may not be an overrun packet yet). While this bit is set, + * no additional packets will be received (some additional + * bytes can still be pending between the wire and the RX + * FIFO). Requires no action on the part of the host. The + * condition is cleared once a few bytes have been read out + * from the RX FIFO. + * 10: 1=TX overrun (RO). Generates adapter failure interrupt. + * Requires TX Reset or Global Reset command to recover. + * Disables Transmitter. + * 9-8: Unassigned. + * 7-0: Built in self test bits for the RX and TX FIFO's. + */ +#define FIFOS_RX_RECEIVING (unsigned short) 0x8000 +#define FIFOS_RX_UNDERRUN (unsigned short) 0x2000 +#define FIFOS_RX_STATUS_OVERRUN (unsigned short) 0x1000 +#define FIFOS_RX_OVERRUN (unsigned short) 0x0800 +#define FIFOS_TX_OVERRUN (unsigned short) 0x0400 + +/* + * Misc defines for various things. + */ +#define TAG_ADAPTER 0xd0 +#define ACTIVATE_ADAPTER_TO_CONFIG 0xff +#define ENABLE_DRQ_IRQ 0x0001 +#define MFG_ID 0x506d /* `TCM' */ +#define PROD_ID 0x5090 +#define GO_WINDOW(x) outw(WINDOW_SELECT|(x),BASE+VX_COMMAND) +#define JABBER_GUARD_ENABLE 0x40 +#define LINKBEAT_ENABLE 0x80 +#define ENABLE_UTP (JABBER_GUARD_ENABLE | LINKBEAT_ENABLE) +#define DISABLE_UTP 0x0 +#define RX_BYTES_MASK (unsigned short) (0x07ff) +#define RX_ERROR 0x4000 +#define RX_INCOMPLETE 0x8000 +#define TX_INDICATE 1<<15 +#define is_eeprom_busy(b) (inw((b)+VX_W0_EEPROM_COMMAND)&EEPROM_BUSY) + +#define VX_IOSIZE 0x20 + +#define VX_CONNECTORS 8 + +/* + * Local variables: + * c-basic-offset: 8 + * End: + */ |
