diff options
Diffstat (limited to 'doc/device-tree-bindings')
| -rw-r--r-- | doc/device-tree-bindings/README | 17 | ||||
| -rw-r--r-- | doc/device-tree-bindings/clock/nvidia,tegra20-car.txt | 207 | ||||
| -rw-r--r-- | doc/device-tree-bindings/i2c/tegra20-i2c.txt | 23 | ||||
| -rw-r--r-- | doc/device-tree-bindings/usb/tegra-usb.txt | 25 |
4 files changed, 272 insertions, 0 deletions
diff --git a/doc/device-tree-bindings/README b/doc/device-tree-bindings/README new file mode 100644 index 0000000000..2ea3439a17 --- /dev/null +++ b/doc/device-tree-bindings/README @@ -0,0 +1,17 @@ +Device Tree Bindings Staging Area +================================= + +This directory contains device tree bindings for U-Boot. + +These follow along with Linux kernel bindings, with a few additions. By +adding the files here, U-Boot patches can clearly show thees additions. +This makes it easier for device tree people to review these additions in +patches sent to the U-Boot mailing list. + +The intent IS to commit these files to U-Boot. Hopefully at some point +the files will be stored in another repo (shared with Linux) which is +brought in as needed. Changes here are intended to mirror changes in the +Linux Documentation/devicetree/bindings/ directory. + +sjg@chromium.org +17-Jan-12 diff --git a/doc/device-tree-bindings/clock/nvidia,tegra20-car.txt b/doc/device-tree-bindings/clock/nvidia,tegra20-car.txt new file mode 100644 index 0000000000..5c07fcaed4 --- /dev/null +++ b/doc/device-tree-bindings/clock/nvidia,tegra20-car.txt @@ -0,0 +1,207 @@ +NVIDIA Tegra20 Clock And Reset Controller + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CAR (Clock And Reset) Controller on Tegra is the HW module responsible +for muxing and gating Tegra's clocks, and setting their rates. + +Required properties : +- compatible : Should be "nvidia,tegra20-car" +- reg : Should contain CAR registers location and length +- clocks : Should contain phandle and clock specifiers for two clocks: + the 32 KHz "32k_in", and the board-specific oscillator "osc". +- #clock-cells : Should be 1. + In clock consumers, this cell represents the clock ID exposed by the CAR. + + The first 96 clocks are numbered to match the bits in the CAR's CLK_OUT_ENB + registers. These IDs often match those in the CAR's RST_DEVICES registers, + but not in all cases. Some bits in CLK_OUT_ENB affect multiple clocks. In + this case, those clocks are assigned IDs above 95 in order to highlight + this issue. Implementations that interpret these clock IDs as bit values + within the CLK_OUT_ENB or RST_DEVICES registers should be careful to + explicitly handle these special cases. + + The balance of the clocks controlled by the CAR are assigned IDs of 96 and + above. + + 0 cpu + 1 unassigned + 2 unassigned + 3 ac97 + 4 rtc + 5 tmr + 6 uart1 + 7 unassigned (register bit affects uart2 and vfir) + 8 gpio + 9 sdmmc2 + 10 unassigned (register bit affects spdif_in and spdif_out) + 11 i2s1 + 12 i2c1 + 13 ndflash + 14 sdmmc1 + 15 sdmmc4 + 16 twc + 17 pwm + 18 i2s2 + 19 epp + 20 unassigned (register bit affects vi and vi_sensor) + 21 2d + 22 usbd + 23 isp + 24 3d + 25 ide + 26 disp2 + 27 disp1 + 28 host1x + 29 vcp + 30 unassigned + 31 cache2 + + 32 mem + 33 ahbdma + 34 apbdma + 35 unassigned + 36 kbc + 37 stat_mon + 38 pmc + 39 fuse + 40 kfuse + 41 sbc1 + 42 snor + 43 spi1 + 44 sbc2 + 45 xio + 46 sbc3 + 47 dvc + 48 dsi + 49 unassigned (register bit affects tvo and cve) + 50 mipi + 51 hdmi + 52 csi + 53 tvdac + 54 i2c2 + 55 uart3 + 56 unassigned + 57 emc + 58 usb2 + 59 usb3 + 60 mpe + 61 vde + 62 bsea + 63 bsev + + 64 speedo + 65 uart4 + 66 uart5 + 67 i2c3 + 68 sbc4 + 69 sdmmc3 + 70 pcie + 71 owr + 72 afi + 73 csite + 74 unassigned + 75 avpucq + 76 la + 77 unassigned + 78 unassigned + 79 unassigned + 80 unassigned + 81 unassigned + 82 unassigned + 83 unassigned + 84 irama + 85 iramb + 86 iramc + 87 iramd + 88 cram2 + 89 audio_2x a/k/a audio_2x_sync_clk + 90 clk_d + 91 unassigned + 92 sus + 93 cdev1 + 94 cdev2 + 95 unassigned + + 96 uart2 + 97 vfir + 98 spdif_in + 99 spdif_out + 100 vi + 101 vi_sensor + 102 tvo + 103 cve + 104 osc + 105 clk_32k a/k/a clk_s + 106 clk_m + 107 sclk + 108 cclk + 109 hclk + 110 pclk + 111 blink + 112 pll_a + 113 pll_a_out0 + 114 pll_c + 115 pll_c_out1 + 116 pll_d + 117 pll_d_out0 + 118 pll_e + 119 pll_m + 120 pll_m_out1 + 121 pll_p + 122 pll_p_out1 + 123 pll_p_out2 + 124 pll_p_out3 + 125 pll_p_out4 + 126 pll_s + 127 pll_u + 128 pll_x + 129 cop a/k/a avp + 130 audio a/k/a audio_sync_clk + +Example SoC include file: + +/ { + tegra_car: clock@60006000 { + compatible = "nvidia,tegra20-car"; + reg = <0x60006000 0x1000>; + #clock-cells = <1>; + }; + + usb@c5004000 { + clocks = <&tegra_car 58>; /* usb2 */ + }; +}; + +Example board file: + +/ { + clocks { + #address-cells = <1>; + #size-cells = <0>; + + osc: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <12000000>; + }; + }; + + i2c@7000d000 { + pmic@34 { + compatible = "ti,tps6586x"; + reg = <0x34>; + + clk_32k: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + }; + + &tegra_car { + clocks = <&clk_32k> <&osc>; + }; +}; diff --git a/doc/device-tree-bindings/i2c/tegra20-i2c.txt b/doc/device-tree-bindings/i2c/tegra20-i2c.txt new file mode 100644 index 0000000000..d601c17f9b --- /dev/null +++ b/doc/device-tree-bindings/i2c/tegra20-i2c.txt @@ -0,0 +1,23 @@ +(Placeholder note while we locate the kernel Tegra20 bindings) + +Added in U-Boot: + +Required properties: + - clocks : Two clocks must be given, each as a phandle to the Tegra's + CAR node and the clock number as a parameter: + - the I2C clock to use for the peripheral + - the pll_p_out3 clock, which can be used for fast operation. This + does not change and is the same for all I2C nodes. + +Example: +(TODO: merge with existing example): + + i2c@7000c400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "nvidia,tegra20-i2c"; + reg = <0x7000C400 0x100>; + interrupts = < 116 >; + /* PERIPH_ID_I2C2, PLL_P_OUT3 */ + clocks = <&tegra_car 54>, <&tegra_car 124>; + }; diff --git a/doc/device-tree-bindings/usb/tegra-usb.txt b/doc/device-tree-bindings/usb/tegra-usb.txt new file mode 100644 index 0000000000..5282d44ac0 --- /dev/null +++ b/doc/device-tree-bindings/usb/tegra-usb.txt @@ -0,0 +1,25 @@ +Tegra SOC USB controllers + +The device node for a USB controller that is part of a Tegra +SOC is as described in the document "Open Firmware Recommended +Practice : Universal Serial Bus" with the following modifications +and additions : + +Required properties : + - compatible : Should be "nvidia,tegra20-ehci" for USB controllers + used in host mode. + - phy_type : Should be one of "ulpi" or "utmi". + - nvidia,vbus-gpio : If present, specifies a gpio that needs to be + activated for the bus to be powered. + +Optional properties: + - dr_mode : dual role mode. Indicates the working mode for + nvidia,tegra20-ehci compatible controllers. Can be "host", "peripheral", + or "otg". Default to "host" if not defined for backward compatibility. + host means this is a host controller + peripheral means it is device controller + otg means it can operate as either ("on the go") + - nvidia,has-legacy-mode : boolean indicates whether this controller can + operate in legacy mode (as APX 2500 / 2600). In legacy mode some + registers are accessed through the APB_MISC base address instead of + the USB controller. |
