diff options
Diffstat (limited to 'board/openrisc/openrisc-generic/or1ksim.cfg')
| -rw-r--r-- | board/openrisc/openrisc-generic/or1ksim.cfg | 122 |
1 files changed, 61 insertions, 61 deletions
diff --git a/board/openrisc/openrisc-generic/or1ksim.cfg b/board/openrisc/openrisc-generic/or1ksim.cfg index 9926093a40..2bd8642932 100644 --- a/board/openrisc/openrisc-generic/or1ksim.cfg +++ b/board/openrisc/openrisc-generic/or1ksim.cfg @@ -20,8 +20,8 @@ the simulator. not found too, it reverts to the built-in default configuration. NOTE: Users should not rely on the built-in configuration, since the - default configuration may differ between version. - Rather create a configuration file that sets all critical values. + default configuration may differ between version. + Rather create a configuration file that sets all critical values. This file may contain (standard C) comments only - no // support. @@ -306,7 +306,7 @@ end debug = 0-9 0 : no debug messages 1-9: debug message level. - higher numbers produce more messages + higher numbers produce more messages profile = 0/1 '0': don't generate profiling file 'sim.profile' @@ -375,11 +375,11 @@ end Core Verification. enabled = 0/1 - '0': disbable VAPI server - '1': enable/start VAPI server + '0': disbable VAPI server + '1': enable/start VAPI server server_port = <value> - TCP/IP port to start VAPI server on + TCP/IP port to start VAPI server on log_enabled = 0/1 '0': disable VAPI requests logging @@ -565,56 +565,56 @@ end This section configures the UARTs enabled = <0|1> - Enable/disable the peripheral. By default if it is enabled. + Enable/disable the peripheral. By default if it is enabled. baseaddr = <hex_value> - address of first UART register for this device + address of first UART register for this device channel = <channeltype>:<args> - The channel parameter indicates the source of received UART characters - and the sink for transmitted UART characters. + The channel parameter indicates the source of received UART characters + and the sink for transmitted UART characters. - The <channeltype> can be either "file", "xterm", "tcp", "fd", or "tty" - (without quotes). + The <channeltype> can be either "file", "xterm", "tcp", "fd", or "tty" + (without quotes). - A) To send/receive characters from a pair of files, use a file - channel: + A) To send/receive characters from a pair of files, use a file + channel: - channel=file:<rxfile>,<txfile> + channel=file:<rxfile>,<txfile> B) To create an interactive terminal window, use an xterm channel: - channel=xterm:[<xterm_arg>]* + channel=xterm:[<xterm_arg>]* C) To create a bidirectional tcp socket which one could, for example, - access via telnet, use a tcp channel: + access via telnet, use a tcp channel: - channel=tcp:<port number> + channel=tcp:<port number> D) To cause the UART to read/write from existing numeric file - descriptors, use an fd channel: + descriptors, use an fd channel: - channel=fd:<rx file descriptor num>,<tx file descriptor num> + channel=fd:<rx file descriptor num>,<tx file descriptor num> - E) To connect the UART to a physical serial port, create a tty - channel: + E) To connect the UART to a physical serial port, create a tty + channel: channel=tty:device=/dev/ttyS0,baud=9600 irq = <value> - irq number for this device + irq number for this device 16550 = 0/1 - '0': this device is a UART16450 - '1': this device is a UART16550 + '0': this device is a UART16450 + '1': this device is a UART16550 jitter = <value> - in msecs... time to block, -1 to disable it + in msecs... time to block, -1 to disable it vapi_id = <hex_value> - VAPI id of this instance + VAPI id of this instance */ section uart @@ -634,16 +634,16 @@ end This section configures the DMAs enabled = <0|1> - Enable/disable the peripheral. By default if it is enabled. + Enable/disable the peripheral. By default if it is enabled. baseaddr = <hex_value> - address of first DMA register for this device + address of first DMA register for this device irq = <value> - irq number for this device + irq number for this device vapi_id = <hex_value> - VAPI id of this instance + VAPI id of this instance */ section dma @@ -658,37 +658,37 @@ end This section configures the ETHERNETs enabled = <0|1> - Enable/disable the peripheral. By default if it is enabled. + Enable/disable the peripheral. By default if it is enabled. baseaddr = <hex_value> - address of first ethernet register for this device + address of first ethernet register for this device dma = <value> - which controller is this ethernet "connected" to + which controller is this ethernet "connected" to irq = <value> - ethernet mac IRQ level + ethernet mac IRQ level rtx_type = <value> - use 0 - file interface, 1 - socket interface + use 0 - file interface, 1 - socket interface rx_channel = <value> - DMA channel used for RX + DMA channel used for RX tx_channel = <value> - DMA channel used for TX + DMA channel used for TX rxfile = "<filename>" - filename, where to read data from + filename, where to read data from txfile = "<filename>" - filename, where to write data to + filename, where to write data to sockif = "<ifacename>" - interface name of ethernet socket + interface name of ethernet socket vapi_id = <hex_value> - VAPI id of this instance + VAPI id of this instance */ section ethernet @@ -711,16 +711,16 @@ end This section configures the GPIOs enabled = <0|1> - Enable/disable the peripheral. By default if it is enabled. + Enable/disable the peripheral. By default if it is enabled. baseaddr = <hex_value> - address of first GPIO register for this device + address of first GPIO register for this device irq = <value> - irq number for this device + irq number for this device base_vapi_id = <hex_value> - first VAPI id of this instance + first VAPI id of this instance GPIO uses 8 consecutive VAPI IDs */ @@ -736,19 +736,19 @@ end This section configures the VGA/LCD controller enabled = <0|1> - Enable/disable the peripheral. By default if it is enabled. + Enable/disable the peripheral. By default if it is enabled. baseaddr = <hex_value> - address of first VGA register + address of first VGA register irq = <value> - irq number for this device + irq number for this device refresh_rate = <value> - number of cycles between screen dumps + number of cycles between screen dumps filename = "<filename>" - template name for generated names (e.g. "primary" produces "primary0023.bmp") + template name for generated names (e.g. "primary" produces "primary0023.bmp") */ section vga @@ -825,39 +825,39 @@ end This section configures the ATA/ATAPI host controller baseaddr = <hex_value> - address of first ATA register + address of first ATA register enabled = <0|1> - Enable/disable the peripheral. By default if it is enabled. + Enable/disable the peripheral. By default if it is enabled. irq = <value> - irq number for this device + irq number for this device debug = <value> - debug level for ata models. + debug level for ata models. 0: no debug messages 1: verbose messages 3: normal messages (more messages than verbose) - 5: debug messages (normal debug messages) + 5: debug messages (normal debug messages) 7: flow control messages (debug statemachine flows) 9: low priority message (display everything the code does) dev_type0/1 = <value> - ata device 0 type - 0: NO_CONNeCT: none (not connected) + ata device 0 type + 0: NO_CONNeCT: none (not connected) 1: FILE : simulated harddisk 2: LOCAL : local system harddisk dev_file0/1 = "<filename>" - filename for simulated ATA device + filename for simulated ATA device valid only if dev_type0 == 1 dev_size0/1 = <value> - size of simulated hard-disk (in MBytes) + size of simulated hard-disk (in MBytes) valid only if dev_type0 == 1 dev_packet0/1 = <value> - 0: simulated ATA device does NOT implement PACKET command feature set + 0: simulated ATA device does NOT implement PACKET command feature set 1: simulated ATA device does implement PACKET command feature set FIXME: irq number |
