diff options
Diffstat (limited to 'board/keymile')
| -rw-r--r-- | board/keymile/kmp204x/Makefile | 2 | ||||
| -rw-r--r-- | board/keymile/kmp204x/kmp204x.c | 128 | ||||
| -rw-r--r-- | board/keymile/kmp204x/kmp204x.h | 10 | ||||
| -rw-r--r-- | board/keymile/kmp204x/pbi.cfg | 10 | ||||
| -rw-r--r-- | board/keymile/kmp204x/pci.c | 85 | ||||
| -rw-r--r-- | board/keymile/kmp204x/qrio.c | 146 | ||||
| -rw-r--r-- | board/keymile/kmp204x/rcw_kmp204x.cfg | 2 |
7 files changed, 305 insertions, 78 deletions
diff --git a/board/keymile/kmp204x/Makefile b/board/keymile/kmp204x/Makefile index 3e69ee2f15..c57ca08e14 100644 --- a/board/keymile/kmp204x/Makefile +++ b/board/keymile/kmp204x/Makefile @@ -8,5 +8,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-y := kmp204x.o ddr.o eth.o tlb.o pci.o law.o \ +obj-y := kmp204x.o ddr.o eth.o tlb.o pci.o law.o qrio.o \ ../common/common.o ../common/ivm.o diff --git a/board/keymile/kmp204x/kmp204x.c b/board/keymile/kmp204x/kmp204x.c index f02642aece..95a19cdb2c 100644 --- a/board/keymile/kmp204x/kmp204x.c +++ b/board/keymile/kmp204x/kmp204x.c @@ -33,12 +33,51 @@ int checkboard(void) return 0; } -/* TODO: implement the I2C deblocking function */ -int i2c_make_abort(void) +/* I2C deblocking uses the algorithm defined in board/keymile/common/common.c + * 2 dedicated QRIO GPIOs externally pull the SCL and SDA lines + * For I2C only the low state is activly driven and high state is pulled-up + * by a resistor. Therefore the deblock GPIOs are used + * -> as an active output to drive a low state + * -> as an open-drain input to have a pulled-up high state + */ + +/* QRIO GPIOs used for deblocking */ +#define DEBLOCK_PORT1 GPIO_A +#define DEBLOCK_SCL1 20 +#define DEBLOCK_SDA1 21 + +/* By default deblock GPIOs are floating */ +static void i2c_deblock_gpio_cfg(void) +{ + /* set I2C bus 1 deblocking GPIOs input, but 0 value for open drain */ + qrio_gpio_direction_input(DEBLOCK_PORT1, DEBLOCK_SCL1); + qrio_gpio_direction_input(DEBLOCK_PORT1, DEBLOCK_SDA1); + + qrio_set_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1, 0); + qrio_set_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1, 0); +} + +void set_sda(int state) +{ + qrio_set_opendrain_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1, state); +} + +void set_scl(int state) +{ + qrio_set_opendrain_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1, state); +} + +int get_sda(void) +{ + return qrio_get_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1); +} + +int get_scl(void) { - return 1; + return qrio_get_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1); } + #define ZL30158_RST 8 #define ZL30343_RST 9 @@ -62,6 +101,7 @@ int board_early_init_f(void) int board_early_init_r(void) { + int ret = 0; /* Flush d-cache and invalidate i-cache of any FLASH data */ flush_dcache(); invalidate_icache(); @@ -69,7 +109,11 @@ int board_early_init_r(void) set_liodns(); setup_portals(); - return 0; + ret = trigger_fpga_config(); + if (ret) + printf("error triggering PCIe FPGA config\n"); + + return ret; } unsigned long get_board_sys_clk(unsigned long dummy) @@ -77,80 +121,12 @@ unsigned long get_board_sys_clk(unsigned long dummy) return 66666666; } -#define WDMASK_OFF 0x16 - -static void qrio_wdmask(u8 bit, bool wden) -{ - u16 wdmask; - void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; - - wdmask = in_be16(qrio_base + WDMASK_OFF); - - if (wden) - wdmask |= (1 << bit); - else - wdmask &= ~(1 << bit); - - out_be16(qrio_base + WDMASK_OFF, wdmask); -} - -#define PRST_OFF 0x1a - -void qrio_prst(u8 bit, bool en, bool wden) -{ - u16 prst; - void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; - - qrio_wdmask(bit, wden); - - prst = in_be16(qrio_base + PRST_OFF); - - if (en) - prst &= ~(1 << bit); - else - prst |= (1 << bit); - - out_be16(qrio_base + PRST_OFF, prst); -} - -#define PRSTCFG_OFF 0x1c - -void qrio_prstcfg(u8 bit, u8 mode) -{ - u32 prstcfg; - u8 i; - void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; - - prstcfg = in_be32(qrio_base + PRSTCFG_OFF); - - for (i = 0; i < 2; i++) { - if (mode & (1<<i)) - set_bit(2*bit+i, &prstcfg); - else - clear_bit(2*bit+i, &prstcfg); - } - - out_be32(qrio_base + PRSTCFG_OFF, prstcfg); -} - - -#define BOOTCOUNT_OFF 0x12 - -void bootcount_store(ulong counter) +int misc_init_f(void) { - u8 val; - void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; - - val = (counter <= 255) ? (u8)counter : 255; - out_8(qrio_base + BOOTCOUNT_OFF, val); -} + /* configure QRIO pis for i2c deblocking */ + i2c_deblock_gpio_cfg(); -ulong bootcount_load(void) -{ - u8 val; - void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; - val = in_8(qrio_base + BOOTCOUNT_OFF); - return val; + return 0; } #define NUM_SRDS_BANKS 2 diff --git a/board/keymile/kmp204x/kmp204x.h b/board/keymile/kmp204x/kmp204x.h index b6ba672413..0267596e4e 100644 --- a/board/keymile/kmp204x/kmp204x.h +++ b/board/keymile/kmp204x/kmp204x.h @@ -5,6 +5,16 @@ * SPDX-License-Identifier: GPL-2.0+ */ +/* QRIO GPIO ports */ +#define GPIO_A 0x40 +#define GPIO_B 0x60 + +int qrio_get_gpio(u8 port_off, u8 gpio_nr); +void qrio_set_opendrain_gpio(u8 port_off, u8 gpio_nr, u8 val); +void qrio_set_gpio(u8 port_off, u8 gpio_nr, bool value); +void qrio_gpio_direction_output(u8 port_off, u8 gpio_nr, bool value); +void qrio_gpio_direction_input(u8 port_off, u8 gpio_nr); + #define PRSTCFG_POWUP_UNIT_CORE_RST 0x0 #define PRSTCFG_POWUP_UNIT_RST 0x1 #define PRSTCFG_POWUP_RST 0x3 diff --git a/board/keymile/kmp204x/pbi.cfg b/board/keymile/kmp204x/pbi.cfg index f38dcf9c8c..9af8bd5b57 100644 --- a/board/keymile/kmp204x/pbi.cfg +++ b/board/keymile/kmp204x/pbi.cfg @@ -8,6 +8,16 @@ # #PBI commands +#Workaround for A-006559 needed for rev 2.0 of P2041 silicon +#Freescale's errarta sheet suggests it may be done with PBI +09000010 00000000 +09000014 00000000 +09000018 81d00000 +09021008 0000f000 +09021028 0000f000 +09021048 0000f000 +09021068 0000f000 +09000018 00000000 #Initialize CPC1 as 1MB SRAM 09010000 00200400 09138000 00000000 diff --git a/board/keymile/kmp204x/pci.c b/board/keymile/kmp204x/pci.c index ec20c8afb4..a484eb5749 100644 --- a/board/keymile/kmp204x/pci.c +++ b/board/keymile/kmp204x/pci.c @@ -14,18 +14,103 @@ #include <libfdt.h> #include <fdt_support.h> #include <asm/fsl_serdes.h> +#include <asm/errno.h> #include "kmp204x.h" +#define PROM_SEL_L 11 +/* control the PROM_SEL_L signal*/ +static void toggle_fpga_eeprom_bus(bool cpu_own) +{ + qrio_gpio_direction_output(GPIO_A, PROM_SEL_L, !cpu_own); +} + +#define CONF_SEL_L 10 +#define FPGA_PROG_L 19 +#define FPGA_DONE 18 +#define FPGA_INIT_L 17 + +int trigger_fpga_config(void) +{ + int ret = 0, init_l; + /* approx 10ms */ + u32 timeout = 10000; + + /* make sure the FPGA_can access the EEPROM */ + toggle_fpga_eeprom_bus(false); + + /* assert CONF_SEL_L to be able to drive FPGA_PROG_L */ + qrio_gpio_direction_output(GPIO_A, CONF_SEL_L, 0); + + /* trigger the config start */ + qrio_gpio_direction_output(GPIO_A, FPGA_PROG_L, 0); + + /* small delay for INIT_L line */ + udelay(10); + + /* wait for FPGA_INIT to be asserted */ + do { + init_l = qrio_get_gpio(GPIO_A, FPGA_INIT_L); + if (timeout-- == 0) { + printf("FPGA_INIT timeout\n"); + ret = -EFAULT; + break; + } + udelay(10); + } while (init_l); + + /* deassert FPGA_PROG, config should start */ + qrio_set_gpio(GPIO_A, FPGA_PROG_L, 1); + + return ret; +} + +/* poll the FPGA_DONE signal and give the EEPROM back to the QorIQ */ +static int wait_for_fpga_config(void) +{ + int ret = 0, done; + /* approx 5 s */ + u32 timeout = 500000; + + printf("PCIe FPGA config:"); + do { + done = qrio_get_gpio(GPIO_A, FPGA_DONE); + if (timeout-- == 0) { + printf(" FPGA_DONE timeout\n"); + ret = -EFAULT; + goto err_out; + } + udelay(10); + } while (!done); + + printf(" done\n"); + +err_out: + /* deactive CONF_SEL and give the CPU conf EEPROM access */ + qrio_set_gpio(GPIO_A, CONF_SEL_L, 1); + toggle_fpga_eeprom_bus(true); + + return ret; +} + #define PCIE_SW_RST 14 +#define PEXHC_SW_RST 13 #define HOOPER_SW_RST 12 void pci_init_board(void) { + /* first wait for the PCIe FPGA to be configured + * it has been triggered earlier in board_early_init_r */ + int ret = wait_for_fpga_config(); + if (ret) + printf("error finishing PCIe FPGA config\n"); + qrio_prst(PCIE_SW_RST, false, false); + qrio_prst(PEXHC_SW_RST, false, false); qrio_prst(HOOPER_SW_RST, false, false); /* Hooper is not direcly PCIe capable */ mdelay(50); + fsl_pcie_init_board(0); } diff --git a/board/keymile/kmp204x/qrio.c b/board/keymile/kmp204x/qrio.c new file mode 100644 index 0000000000..49f9aa2546 --- /dev/null +++ b/board/keymile/kmp204x/qrio.c @@ -0,0 +1,146 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp <valentin.longchamp@keymile.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> + +#include "../common/common.h" +#include "kmp204x.h" + +/* QRIO GPIO register offsets */ +#define DIRECT_OFF 0x18 +#define GPRT_OFF 0x1c + +int qrio_get_gpio(u8 port_off, u8 gpio_nr) +{ + u32 gprt; + + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + gprt = in_be32(qrio_base + port_off + GPRT_OFF); + + return (gprt >> gpio_nr) & 1U; +} + +void qrio_set_gpio(u8 port_off, u8 gpio_nr, bool value) +{ + u32 gprt, mask; + + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + mask = 1U << gpio_nr; + + gprt = in_be32(qrio_base + port_off + GPRT_OFF); + if (value) + gprt |= mask; + else + gprt &= ~mask; + + out_be32(qrio_base + port_off + GPRT_OFF, gprt); +} + +void qrio_gpio_direction_output(u8 port_off, u8 gpio_nr, bool value) +{ + u32 direct, mask; + + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + mask = 1U << gpio_nr; + + direct = in_be32(qrio_base + port_off + DIRECT_OFF); + direct |= mask; + out_be32(qrio_base + port_off + DIRECT_OFF, direct); + + qrio_set_gpio(port_off, gpio_nr, value); +} + +void qrio_gpio_direction_input(u8 port_off, u8 gpio_nr) +{ + u32 direct, mask; + + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + mask = 1U << gpio_nr; + + direct = in_be32(qrio_base + port_off + DIRECT_OFF); + direct &= ~mask; + out_be32(qrio_base + port_off + DIRECT_OFF, direct); +} + +void qrio_set_opendrain_gpio(u8 port_off, u8 gpio_nr, u8 val) +{ + u32 direct, mask; + + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + mask = 1U << gpio_nr; + + direct = in_be32(qrio_base + port_off + DIRECT_OFF); + if (val == 0) + /* set to output -> GPIO drives low */ + direct |= mask; + else + /* set to input -> GPIO floating */ + direct &= ~mask; + + out_be32(qrio_base + port_off + DIRECT_OFF, direct); +} + +#define WDMASK_OFF 0x16 + +static void qrio_wdmask(u8 bit, bool wden) +{ + u16 wdmask; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + wdmask = in_be16(qrio_base + WDMASK_OFF); + + if (wden) + wdmask |= (1 << bit); + else + wdmask &= ~(1 << bit); + + out_be16(qrio_base + WDMASK_OFF, wdmask); +} + +#define PRST_OFF 0x1a + +void qrio_prst(u8 bit, bool en, bool wden) +{ + u16 prst; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + qrio_wdmask(bit, wden); + + prst = in_be16(qrio_base + PRST_OFF); + + if (en) + prst &= ~(1 << bit); + else + prst |= (1 << bit); + + out_be16(qrio_base + PRST_OFF, prst); +} + +#define PRSTCFG_OFF 0x1c + +void qrio_prstcfg(u8 bit, u8 mode) +{ + u32 prstcfg; + u8 i; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + prstcfg = in_be32(qrio_base + PRSTCFG_OFF); + + for (i = 0; i < 2; i++) { + if (mode & (1<<i)) + set_bit(2*bit+i, &prstcfg); + else + clear_bit(2*bit+i, &prstcfg); + } + + out_be32(qrio_base + PRSTCFG_OFF, prstcfg); +} diff --git a/board/keymile/kmp204x/rcw_kmp204x.cfg b/board/keymile/kmp204x/rcw_kmp204x.cfg index f2b7fe3d42..2d4c48cb9c 100644 --- a/board/keymile/kmp204x/rcw_kmp204x.cfg +++ b/board/keymile/kmp204x/rcw_kmp204x.cfg @@ -7,5 +7,5 @@ aa55aa55 010e0100 #64 bytes RCW data 14600000 00000000 28200000 00000000 148E70CF CFC02000 58000000 41000000 -00000000 00000000 00000000 F4428002 +00000000 00000000 00000000 F0428002 00000000 00000000 00000000 00000000 |
