diff options
Diffstat (limited to 'board/freescale/mpc7448hpc2/README')
| -rw-r--r-- | board/freescale/mpc7448hpc2/README | 184 |
1 files changed, 0 insertions, 184 deletions
diff --git a/board/freescale/mpc7448hpc2/README b/board/freescale/mpc7448hpc2/README deleted file mode 100644 index cbb043e1d0..0000000000 --- a/board/freescale/mpc7448hpc2/README +++ /dev/null @@ -1,184 +0,0 @@ -Freescale MPC7448hpc2 (Taiga) board -=================================== - -Created 08/11/2006 Roy Zang --------------------------- -MPC7448hpc2 (Taiga) board is a high-performance PowerPC server reference -design, which is optimized for high speed throughput between the processor and -the memory, disk drive and Ethernet port subsystems. - -MPC7448hpc2(Taiga) is designed to the micro-ATX chassis, allowing it to be -used in 1U or 2U rack-mount chassis¡¯, as well as in standard ATX/Micro-ATX -chassis. - -Building U-Boot ------------------- -The mpc7448hpc2 code base is known to compile using: - Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3 - - $ make mpc7448hpc2_config - Configuring for mpc7448hpc2 board... - - $ make - -Memory Map ----------- - -The memory map is setup for Linux to operate properly. - -The mapping is: - - Range Start Range End Definition Size - - 0x0000_0000 0x7fff_ffff DDR 2G - 0xe000_0000 0xe7ff_ffff PCI Memory 128M - 0xfa00_0000 0xfaff_ffff PCI IO 16M - 0xfb00_0000 0xfbff_ffff PCI Config 16M - 0xfc00_0000 0xfc0f_ffff NVRAM/CADMUS 1M - 0xfe00_0000 0xfeff_ffff PromJet 16M - 0xff00_0000 0xff80_0000 FLASH (boot flash) 8M - 0xff80_0000 0xffff_ffff FLASH (second half flash) 8M - -Using Flash ------------ - -The MPC7448hpc2 board has two "banks" of flash, each 8MB in size -(2^23 = 0x00800000). - -Note: the "bank" here refers to half of the flash. In fact, there is only one -bank of flash, which is divided into low and high half. Each is controlled by -the most significant bit of the address bus. The so called "bank" is only for -convenience. - -There is a switch which allows the "bank" to be selected. The switch -settings for updating flash are given below. - -The u-boot commands for copying the boot-bank into the secondary bank are -as follows: - - erase ff800000 ff880000 - cp.b ff000000 ff800000 80000 - -U-boot commands for downloading an image via tftp and flashing -it into the secondary bank: - - tftp 10000 <u-boot.bin.image> - erase ff000000 ff080000 - cp.b 10000 ff000000 80000 - -After copying the image into the second bank of flash, be sure to toggle -SW3[4] on board before resetting the board in order to set the -secondary bank as the boot-bank. - -Board Switches ----------------------- - -Most switches on the board should not be changed. The most frequent -user-settable switches on the board are used to configure -the flash banks and determining the PCI frequency. - -SW1[1-5]: Processor core voltage - - 12345 Core Voltage - ----- - SW1=01111 1.000V. - SW1=01101 1.100V. - SW1=01011 1.200V. - SW1=01001 1.300V only for MPC7447A. - - -SW2[1-6]: CPU core frequency - - CPU Core Frequency (MHz) - Bus Frequency - 123456 100 133 167 200 Ratio - - ------ - SW2=101100 500 667 833 1000 5x - SW2=100100 550 733 917 1100 5.5x - SW2=110100 600 800 1000 1200 6x - SW2=010100 650 866 1083 1300 6.5x - SW2=001000 700 930 1167 1400 7x - SW2=000100 750 1000 1250 1500 7.5x - SW2=110000 800 1066 1333 1600 8x - SW2=011000 850 1333 1417 1700 8.5x only for MPC7447A - SW2=011110 900 1200 1500 1800 9x - -This table shows only a subset of available frequency options; see the CPU -hardware specifications for more information. - -SW2[7-8]: Bus Protocol and CPU Reset Option - - 7 - - - SW2=0 System bus uses MPX bus protocol - SW2=1 System bus uses 60x bus protocol - - 8 - - - SW2=0 TSI108 can cause CPU reset - SW2=1 TSI108 can not cause CPU reset - -SW3[1-8] system options - - 123 - --- - SW3=xxx Connected to GPIO[0:2] on TSI108 - - 4 - - - SW3=0 CPU boots from low half of flash - SW3=1 CPU boots from high half of flash - - 5 - - - SW3=0 SATA and slot2 connected to PCI bus - SW3=1 Only slot1 connected to PCI bus - - 6 - - - SW3=0 USB connected to PCI bus - SW3=1 USB disconnected from PCI bus - - 7 - - - SW3=0 Flash is write protected - SW3=1 Flash is NOT write protected - - 8 - - - SW3=0 CPU will boot from flash - SW3=1 CPU will boot from PromJet - -SW4[1-3]: System bus frequency - - Bus Frequency (MHz) - --- - SW4=010 183 - SW4=011 100 - SW4=100 133 - SW4=101 166 only for MPC7447A - SW4=110 200 only for MPC7448 - others reserved - -SW4[4-6]: DDR2 SDRAM frequency - - Bus Frequency (MHz) - --- - SW4=000 external clock - SW4=011 system clock - SW4=100 133 - SW4=101 166 - SW4=110 200 - others reserved - -SW4[7-8]: PCI/PCI-X frequency control - 7 - - - SW4=0 PCI/PCI-X bus operates normally - SW4=1 PCI bus forced to PCI-33 mode - - 8 - - - SW4=0 PCI-X mode at 133 MHz allowed - SW4=1 PCI-X mode limited to 100 MHz |
