diff options
Diffstat (limited to 'arch/ppc/cpu/mpc8xxx/ddr/ctrl_regs.c')
| -rw-r--r-- | arch/ppc/cpu/mpc8xxx/ddr/ctrl_regs.c | 1366 |
1 files changed, 1366 insertions, 0 deletions
diff --git a/arch/ppc/cpu/mpc8xxx/ddr/ctrl_regs.c b/arch/ppc/cpu/mpc8xxx/ddr/ctrl_regs.c new file mode 100644 index 0000000000..03f9c4380d --- /dev/null +++ b/arch/ppc/cpu/mpc8xxx/ddr/ctrl_regs.c @@ -0,0 +1,1366 @@ +/* + * Copyright 2008-2010 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +/* + * Generic driver for Freescale DDR/DDR2/DDR3 memory controller. + * Based on code from spd_sdram.c + * Author: James Yang [at freescale.com] + */ + +#include <common.h> +#include <asm/fsl_ddr_sdram.h> + +#include "ddr.h" + +extern unsigned int picos_to_mclk(unsigned int picos); +/* + * Determine Rtt value. + * + * This should likely be either board or controller specific. + * + * Rtt(nominal) - DDR2: + * 0 = Rtt disabled + * 1 = 75 ohm + * 2 = 150 ohm + * 3 = 50 ohm + * Rtt(nominal) - DDR3: + * 0 = Rtt disabled + * 1 = 60 ohm + * 2 = 120 ohm + * 3 = 40 ohm + * 4 = 20 ohm + * 5 = 30 ohm + * + * FIXME: Apparently 8641 needs a value of 2 + * FIXME: Old code seys if 667 MHz or higher, use 3 on 8572 + * + * FIXME: There was some effort down this line earlier: + * + * unsigned int i; + * for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL/2; i++) { + * if (popts->dimmslot[i].num_valid_cs + * && (popts->cs_local_opts[2*i].odt_rd_cfg + * || popts->cs_local_opts[2*i].odt_wr_cfg)) { + * rtt = 2; + * break; + * } + * } + */ +static inline int fsl_ddr_get_rtt(void) +{ + int rtt; + +#if defined(CONFIG_FSL_DDR1) + rtt = 0; +#elif defined(CONFIG_FSL_DDR2) + rtt = 3; +#else + rtt = 0; +#endif + + return rtt; +} + +/* + * compute the CAS write latency according to DDR3 spec + * CWL = 5 if tCK >= 2.5ns + * 6 if 2.5ns > tCK >= 1.875ns + * 7 if 1.875ns > tCK >= 1.5ns + * 8 if 1.5ns > tCK >= 1.25ns + */ +static inline unsigned int compute_cas_write_latency(void) +{ + unsigned int cwl; + const unsigned int mclk_ps = get_memory_clk_period_ps(); + + if (mclk_ps >= 2500) + cwl = 5; + else if (mclk_ps >= 1875) + cwl = 6; + else if (mclk_ps >= 1500) + cwl = 7; + else if (mclk_ps >= 1250) + cwl = 8; + else + cwl = 8; + return cwl; +} + +/* Chip Select Configuration (CSn_CONFIG) */ +static void set_csn_config(int i, fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const dimm_params_t *dimm_params) +{ + unsigned int cs_n_en = 0; /* Chip Select enable */ + unsigned int intlv_en = 0; /* Memory controller interleave enable */ + unsigned int intlv_ctl = 0; /* Interleaving control */ + unsigned int ap_n_en = 0; /* Chip select n auto-precharge enable */ + unsigned int odt_rd_cfg = 0; /* ODT for reads configuration */ + unsigned int odt_wr_cfg = 0; /* ODT for writes configuration */ + unsigned int ba_bits_cs_n = 0; /* Num of bank bits for SDRAM on CSn */ + unsigned int row_bits_cs_n = 0; /* Num of row bits for SDRAM on CSn */ + unsigned int col_bits_cs_n = 0; /* Num of ocl bits for SDRAM on CSn */ + + /* Compute CS_CONFIG only for existing ranks of each DIMM. */ + if ((((i&1) == 0) + && (dimm_params[i/2].n_ranks == 1)) + || (dimm_params[i/2].n_ranks == 2)) { + unsigned int n_banks_per_sdram_device; + cs_n_en = 1; + if (i == 0) { + /* These fields only available in CS0_CONFIG */ + intlv_en = popts->memctl_interleaving; + intlv_ctl = popts->memctl_interleaving_mode; + } + ap_n_en = popts->cs_local_opts[i].auto_precharge; + odt_rd_cfg = popts->cs_local_opts[i].odt_rd_cfg; + odt_wr_cfg = popts->cs_local_opts[i].odt_wr_cfg; + n_banks_per_sdram_device + = dimm_params[i/2].n_banks_per_sdram_device; + ba_bits_cs_n = __ilog2(n_banks_per_sdram_device) - 2; + row_bits_cs_n = dimm_params[i/2].n_row_addr - 12; + col_bits_cs_n = dimm_params[i/2].n_col_addr - 8; + } + + ddr->cs[i].config = (0 + | ((cs_n_en & 0x1) << 31) + | ((intlv_en & 0x3) << 29) + | ((intlv_ctl & 0xf) << 24) + | ((ap_n_en & 0x1) << 23) + + /* XXX: some implementation only have 1 bit starting at left */ + | ((odt_rd_cfg & 0x7) << 20) + + /* XXX: Some implementation only have 1 bit starting at left */ + | ((odt_wr_cfg & 0x7) << 16) + + | ((ba_bits_cs_n & 0x3) << 14) + | ((row_bits_cs_n & 0x7) << 8) + | ((col_bits_cs_n & 0x7) << 0) + ); + debug("FSLDDR: cs[%d]_config = 0x%08x\n", i,ddr->cs[i].config); +} + +/* Chip Select Configuration 2 (CSn_CONFIG_2) */ +/* FIXME: 8572 */ +static void set_csn_config_2(int i, fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int pasr_cfg = 0; /* Partial array self refresh config */ + + ddr->cs[i].config_2 = ((pasr_cfg & 7) << 24); + debug("FSLDDR: cs[%d]_config_2 = 0x%08x\n", i, ddr->cs[i].config_2); +} + +/* -3E = 667 CL5, -25 = CL6 800, -25E = CL5 800 */ + +#if !defined(CONFIG_FSL_DDR1) +/* + * DDR SDRAM Timing Configuration 0 (TIMING_CFG_0) + * + * Avoid writing for DDR I. The new PQ38 DDR controller + * dreams up non-zero default values to be backwards compatible. + */ +static void set_timing_cfg_0(fsl_ddr_cfg_regs_t *ddr) +{ + unsigned char trwt_mclk = 0; /* Read-to-write turnaround */ + unsigned char twrt_mclk = 0; /* Write-to-read turnaround */ + /* 7.5 ns on -3E; 0 means WL - CL + BL/2 + 1 */ + unsigned char trrt_mclk = 0; /* Read-to-read turnaround */ + unsigned char twwt_mclk = 0; /* Write-to-write turnaround */ + + /* Active powerdown exit timing (tXARD and tXARDS). */ + unsigned char act_pd_exit_mclk; + /* Precharge powerdown exit timing (tXP). */ + unsigned char pre_pd_exit_mclk; + /* Precharge powerdown exit timing (tAXPD). */ + unsigned char taxpd_mclk; + /* Mode register set cycle time (tMRD). */ + unsigned char tmrd_mclk; + +#if defined(CONFIG_FSL_DDR3) + /* + * (tXARD and tXARDS). Empirical? + * The DDR3 spec has not tXARD, + * we use the tXP instead of it. + * tXP=max(3nCK, 7.5ns) for DDR3. + * spec has not the tAXPD, we use + * tAXPD=8, need design to confirm. + */ + int tXP = max((get_memory_clk_period_ps() * 3), 7500); /* unit=ps */ + act_pd_exit_mclk = picos_to_mclk(tXP); + /* Mode register MR0[A12] is '1' - fast exit */ + pre_pd_exit_mclk = act_pd_exit_mclk; + taxpd_mclk = 8; + tmrd_mclk = 4; +#else /* CONFIG_FSL_DDR2 */ + /* + * (tXARD and tXARDS). Empirical? + * tXARD = 2 for DDR2 + * tXP=2 + * tAXPD=8 + */ + act_pd_exit_mclk = 2; + pre_pd_exit_mclk = 2; + taxpd_mclk = 8; + tmrd_mclk = 2; +#endif + + ddr->timing_cfg_0 = (0 + | ((trwt_mclk & 0x3) << 30) /* RWT */ + | ((twrt_mclk & 0x3) << 28) /* WRT */ + | ((trrt_mclk & 0x3) << 26) /* RRT */ + | ((twwt_mclk & 0x3) << 24) /* WWT */ + | ((act_pd_exit_mclk & 0x7) << 20) /* ACT_PD_EXIT */ + | ((pre_pd_exit_mclk & 0xF) << 16) /* PRE_PD_EXIT */ + | ((taxpd_mclk & 0xf) << 8) /* ODT_PD_EXIT */ + | ((tmrd_mclk & 0xf) << 0) /* MRS_CYC */ + ); + debug("FSLDDR: timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0); +} +#endif /* defined(CONFIG_FSL_DDR2) */ + +/* DDR SDRAM Timing Configuration 3 (TIMING_CFG_3) */ +static void set_timing_cfg_3(fsl_ddr_cfg_regs_t *ddr, + const common_timing_params_t *common_dimm, + unsigned int cas_latency) +{ + /* Extended Activate to precharge interval (tRAS) */ + unsigned int ext_acttopre = 0; + unsigned int ext_refrec; /* Extended refresh recovery time (tRFC) */ + unsigned int ext_caslat = 0; /* Extended MCAS latency from READ cmd */ + unsigned int cntl_adj = 0; /* Control Adjust */ + + /* If the tRAS > 19 MCLK, we use the ext mode */ + if (picos_to_mclk(common_dimm->tRAS_ps) > 0x13) + ext_acttopre = 1; + + ext_refrec = (picos_to_mclk(common_dimm->tRFC_ps) - 8) >> 4; + + /* If the CAS latency more than 8, use the ext mode */ + if (cas_latency > 8) + ext_caslat = 1; + + ddr->timing_cfg_3 = (0 + | ((ext_acttopre & 0x1) << 24) + | ((ext_refrec & 0xF) << 16) + | ((ext_caslat & 0x1) << 12) + | ((cntl_adj & 0x7) << 0) + ); + debug("FSLDDR: timing_cfg_3 = 0x%08x\n", ddr->timing_cfg_3); +} + +/* DDR SDRAM Timing Configuration 1 (TIMING_CFG_1) */ +static void set_timing_cfg_1(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm, + unsigned int cas_latency) +{ + /* Precharge-to-activate interval (tRP) */ + unsigned char pretoact_mclk; + /* Activate to precharge interval (tRAS) */ + unsigned char acttopre_mclk; + /* Activate to read/write interval (tRCD) */ + unsigned char acttorw_mclk; + /* CASLAT */ + unsigned char caslat_ctrl; + /* Refresh recovery time (tRFC) ; trfc_low */ + unsigned char refrec_ctrl; + /* Last data to precharge minimum interval (tWR) */ + unsigned char wrrec_mclk; + /* Activate-to-activate interval (tRRD) */ + unsigned char acttoact_mclk; + /* Last write data pair to read command issue interval (tWTR) */ + unsigned char wrtord_mclk; + + pretoact_mclk = picos_to_mclk(common_dimm->tRP_ps); + acttopre_mclk = picos_to_mclk(common_dimm->tRAS_ps); + acttorw_mclk = picos_to_mclk(common_dimm->tRCD_ps); + + /* + * Translate CAS Latency to a DDR controller field value: + * + * CAS Lat DDR I DDR II Ctrl + * Clocks SPD Bit SPD Bit Value + * ------- ------- ------- ----- + * 1.0 0 0001 + * 1.5 1 0010 + * 2.0 2 2 0011 + * 2.5 3 0100 + * 3.0 4 3 0101 + * 3.5 5 0110 + * 4.0 4 0111 + * 4.5 1000 + * 5.0 5 1001 + */ +#if defined(CONFIG_FSL_DDR1) + caslat_ctrl = (cas_latency + 1) & 0x07; +#elif defined(CONFIG_FSL_DDR2) + caslat_ctrl = 2 * cas_latency - 1; +#else + /* + * if the CAS latency more than 8 cycle, + * we need set extend bit for it at + * TIMING_CFG_3[EXT_CASLAT] + */ + if (cas_latency > 8) + cas_latency -= 8; + caslat_ctrl = 2 * cas_latency - 1; +#endif + + refrec_ctrl = picos_to_mclk(common_dimm->tRFC_ps) - 8; + wrrec_mclk = picos_to_mclk(common_dimm->tWR_ps); + if (popts->OTF_burst_chop_en) + wrrec_mclk += 2; + + acttoact_mclk = picos_to_mclk(common_dimm->tRRD_ps); + /* + * JEDEC has min requirement for tRRD + */ +#if defined(CONFIG_FSL_DDR3) + if (acttoact_mclk < 4) + acttoact_mclk = 4; +#endif + wrtord_mclk = picos_to_mclk(common_dimm->tWTR_ps); + /* + * JEDEC has some min requirements for tWTR + */ +#if defined(CONFIG_FSL_DDR2) + if (wrtord_mclk < 2) + wrtord_mclk = 2; +#elif defined(CONFIG_FSL_DDR3) + if (wrtord_mclk < 4) + wrtord_mclk = 4; +#endif + if (popts->OTF_burst_chop_en) + wrtord_mclk += 2; + + ddr->timing_cfg_1 = (0 + | ((pretoact_mclk & 0x0F) << 28) + | ((acttopre_mclk & 0x0F) << 24) + | ((acttorw_mclk & 0xF) << 20) + | ((caslat_ctrl & 0xF) << 16) + | ((refrec_ctrl & 0xF) << 12) + | ((wrrec_mclk & 0x0F) << 8) + | ((acttoact_mclk & 0x07) << 4) + | ((wrtord_mclk & 0x07) << 0) + ); + debug("FSLDDR: timing_cfg_1 = 0x%08x\n", ddr->timing_cfg_1); +} + +/* DDR SDRAM Timing Configuration 2 (TIMING_CFG_2) */ +static void set_timing_cfg_2(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm, + unsigned int cas_latency, + unsigned int additive_latency) +{ + /* Additive latency */ + unsigned char add_lat_mclk; + /* CAS-to-preamble override */ + unsigned short cpo; + /* Write latency */ + unsigned char wr_lat; + /* Read to precharge (tRTP) */ + unsigned char rd_to_pre; + /* Write command to write data strobe timing adjustment */ + unsigned char wr_data_delay; + /* Minimum CKE pulse width (tCKE) */ + unsigned char cke_pls; + /* Window for four activates (tFAW) */ + unsigned short four_act; + + /* FIXME add check that this must be less than acttorw_mclk */ + add_lat_mclk = additive_latency; + cpo = popts->cpo_override; + +#if defined(CONFIG_FSL_DDR1) + /* + * This is a lie. It should really be 1, but if it is + * set to 1, bits overlap into the old controller's + * otherwise unused ACSM field. If we leave it 0, then + * the HW will magically treat it as 1 for DDR 1. Oh Yea. + */ + wr_lat = 0; +#elif defined(CONFIG_FSL_DDR2) + wr_lat = cas_latency - 1; +#else + wr_lat = compute_cas_write_latency(); +#endif + + rd_to_pre = picos_to_mclk(common_dimm->tRTP_ps); + /* + * JEDEC has some min requirements for tRTP + */ +#if defined(CONFIG_FSL_DDR2) + if (rd_to_pre < 2) + rd_to_pre = 2; +#elif defined(CONFIG_FSL_DDR3) + if (rd_to_pre < 4) + rd_to_pre = 4; +#endif + if (additive_latency) + rd_to_pre += additive_latency; + if (popts->OTF_burst_chop_en) + rd_to_pre += 2; /* according to UM */ + + wr_data_delay = popts->write_data_delay; + cke_pls = picos_to_mclk(popts->tCKE_clock_pulse_width_ps); + four_act = picos_to_mclk(popts->tFAW_window_four_activates_ps); + + ddr->timing_cfg_2 = (0 + | ((add_lat_mclk & 0xf) << 28) + | ((cpo & 0x1f) << 23) + | ((wr_lat & 0xf) << 19) + | ((rd_to_pre & RD_TO_PRE_MASK) << RD_TO_PRE_SHIFT) + | ((wr_data_delay & WR_DATA_DELAY_MASK) << WR_DATA_DELAY_SHIFT) + | ((cke_pls & 0x7) << 6) + | ((four_act & 0x3f) << 0) + ); + debug("FSLDDR: timing_cfg_2 = 0x%08x\n", ddr->timing_cfg_2); +} + +/* DDR SDRAM control configuration (DDR_SDRAM_CFG) */ +static void set_ddr_sdram_cfg(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm) +{ + unsigned int mem_en; /* DDR SDRAM interface logic enable */ + unsigned int sren; /* Self refresh enable (during sleep) */ + unsigned int ecc_en; /* ECC enable. */ + unsigned int rd_en; /* Registered DIMM enable */ + unsigned int sdram_type; /* Type of SDRAM */ + unsigned int dyn_pwr; /* Dynamic power management mode */ + unsigned int dbw; /* DRAM dta bus width */ + unsigned int eight_be = 0; /* 8-beat burst enable, DDR2 is zero */ + unsigned int ncap = 0; /* Non-concurrent auto-precharge */ + unsigned int threeT_en; /* Enable 3T timing */ + unsigned int twoT_en; /* Enable 2T timing */ + unsigned int ba_intlv_ctl; /* Bank (CS) interleaving control */ + unsigned int x32_en = 0; /* x32 enable */ + unsigned int pchb8 = 0; /* precharge bit 8 enable */ + unsigned int hse; /* Global half strength override */ + unsigned int mem_halt = 0; /* memory controller halt */ + unsigned int bi = 0; /* Bypass initialization */ + + mem_en = 1; + sren = popts->self_refresh_in_sleep; + if (common_dimm->all_DIMMs_ECC_capable) { + /* Allow setting of ECC only if all DIMMs are ECC. */ + ecc_en = popts->ECC_mode; + } else { + ecc_en = 0; + } + + rd_en = (common_dimm->all_DIMMs_registered + && !common_dimm->all_DIMMs_unbuffered); + + sdram_type = CONFIG_FSL_SDRAM_TYPE; + + dyn_pwr = popts->dynamic_power; + dbw = popts->data_bus_width; + /* 8-beat burst enable DDR-III case + * we must clear it when use the on-the-fly mode, + * must set it when use the 32-bits bus mode. + */ + if (sdram_type == SDRAM_TYPE_DDR3) { + if (popts->burst_length == DDR_BL8) + eight_be = 1; + if (popts->burst_length == DDR_OTF) + eight_be = 0; + if (dbw == 0x1) + eight_be = 1; + } + + threeT_en = popts->threeT_en; + twoT_en = popts->twoT_en; + ba_intlv_ctl = popts->ba_intlv_ctl; + hse = popts->half_strength_driver_enable; + + ddr->ddr_sdram_cfg = (0 + | ((mem_en & 0x1) << 31) + | ((sren & 0x1) << 30) + | ((ecc_en & 0x1) << 29) + | ((rd_en & 0x1) << 28) + | ((sdram_type & 0x7) << 24) + | ((dyn_pwr & 0x1) << 21) + | ((dbw & 0x3) << 19) + | ((eight_be & 0x1) << 18) + | ((ncap & 0x1) << 17) + | ((threeT_en & 0x1) << 16) + | ((twoT_en & 0x1) << 15) + | ((ba_intlv_ctl & 0x7F) << 8) + | ((x32_en & 0x1) << 5) + | ((pchb8 & 0x1) << 4) + | ((hse & 0x1) << 3) + | ((mem_halt & 0x1) << 1) + | ((bi & 0x1) << 0) + ); + debug("FSLDDR: ddr_sdram_cfg = 0x%08x\n", ddr->ddr_sdram_cfg); +} + +/* DDR SDRAM control configuration 2 (DDR_SDRAM_CFG_2) */ +static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts) +{ + unsigned int frc_sr = 0; /* Force self refresh */ + unsigned int sr_ie = 0; /* Self-refresh interrupt enable */ + unsigned int dll_rst_dis; /* DLL reset disable */ + unsigned int dqs_cfg; /* DQS configuration */ + unsigned int odt_cfg; /* ODT configuration */ + unsigned int num_pr; /* Number of posted refreshes */ + unsigned int obc_cfg; /* On-The-Fly Burst Chop Cfg */ + unsigned int ap_en; /* Address Parity Enable */ + unsigned int d_init; /* DRAM data initialization */ + unsigned int rcw_en = 0; /* Register Control Word Enable */ + unsigned int md_en = 0; /* Mirrored DIMM Enable */ + + dll_rst_dis = 1; /* Make this configurable */ + dqs_cfg = popts->DQS_config; + if (popts->cs_local_opts[0].odt_rd_cfg + || popts->cs_local_opts[0].odt_wr_cfg) { + /* FIXME */ + odt_cfg = 2; + } else { + odt_cfg = 0; + } + + num_pr = 1; /* Make this configurable */ + + /* + * 8572 manual says + * {TIMING_CFG_1[PRETOACT] + * + [DDR_SDRAM_CFG_2[NUM_PR] + * * ({EXT_REFREC || REFREC} + 8 + 2)]} + * << DDR_SDRAM_INTERVAL[REFINT] + */ +#if defined(CONFIG_FSL_DDR3) + obc_cfg = popts->OTF_burst_chop_en; +#else + obc_cfg = 0; +#endif + + ap_en = 0; /* Make this configurable? */ + +#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* Use the DDR controller to auto initialize memory. */ + d_init = 1; + ddr->ddr_data_init = CONFIG_MEM_INIT_VALUE; + debug("DDR: ddr_data_init = 0x%08x\n", ddr->ddr_data_init); +#else + /* Memory will be initialized via DMA, or not at all. */ + d_init = 0; +#endif + +#if defined(CONFIG_FSL_DDR3) + md_en = popts->mirrored_dimm; +#endif + ddr->ddr_sdram_cfg_2 = (0 + | ((frc_sr & 0x1) << 31) + | ((sr_ie & 0x1) << 30) + | ((dll_rst_dis & 0x1) << 29) + | ((dqs_cfg & 0x3) << 26) + | ((odt_cfg & 0x3) << 21) + | ((num_pr & 0xf) << 12) + | ((obc_cfg & 0x1) << 6) + | ((ap_en & 0x1) << 5) + | ((d_init & 0x1) << 4) + | ((rcw_en & 0x1) << 2) + | ((md_en & 0x1) << 0) + ); + debug("FSLDDR: ddr_sdram_cfg_2 = 0x%08x\n", ddr->ddr_sdram_cfg_2); +} + +/* DDR SDRAM Mode configuration 2 (DDR_SDRAM_MODE_2) */ +static void set_ddr_sdram_mode_2(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts) +{ + unsigned short esdmode2 = 0; /* Extended SDRAM mode 2 */ + unsigned short esdmode3 = 0; /* Extended SDRAM mode 3 */ + +#if defined(CONFIG_FSL_DDR3) + unsigned int rtt_wr = 0; /* Rtt_WR - dynamic ODT off */ + unsigned int srt = 0; /* self-refresh temerature, normal range */ + unsigned int asr = 0; /* auto self-refresh disable */ + unsigned int cwl = compute_cas_write_latency() - 5; + unsigned int pasr = 0; /* partial array self refresh disable */ + + if (popts->rtt_override) + rtt_wr = popts->rtt_wr_override_value; + + esdmode2 = (0 + | ((rtt_wr & 0x3) << 9) + | ((srt & 0x1) << 7) + | ((asr & 0x1) << 6) + | ((cwl & 0x7) << 3) + | ((pasr & 0x7) << 0)); +#endif + ddr->ddr_sdram_mode_2 = (0 + | ((esdmode2 & 0xFFFF) << 16) + | ((esdmode3 & 0xFFFF) << 0) + ); + debug("FSLDDR: ddr_sdram_mode_2 = 0x%08x\n", ddr->ddr_sdram_mode_2); +} + +/* DDR SDRAM Interval Configuration (DDR_SDRAM_INTERVAL) */ +static void set_ddr_sdram_interval(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm) +{ + unsigned int refint; /* Refresh interval */ + unsigned int bstopre; /* Precharge interval */ + + refint = picos_to_mclk(common_dimm->refresh_rate_ps); + + bstopre = popts->bstopre; + + /* refint field used 0x3FFF in earlier controllers */ + ddr->ddr_sdram_interval = (0 + | ((refint & 0xFFFF) << 16) + | ((bstopre & 0x3FFF) << 0) + ); + debug("FSLDDR: ddr_sdram_interval = 0x%08x\n", ddr->ddr_sdram_interval); +} + +#if defined(CONFIG_FSL_DDR3) +/* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */ +static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm, + unsigned int cas_latency, + unsigned int additive_latency) +{ + unsigned short esdmode; /* Extended SDRAM mode */ + unsigned short sdmode; /* SDRAM mode */ + + /* Mode Register - MR1 */ + unsigned int qoff = 0; /* Output buffer enable 0=yes, 1=no */ + unsigned int tdqs_en = 0; /* TDQS Enable: 0=no, 1=yes */ + unsigned int rtt; + unsigned int wrlvl_en = 0; /* Write level enable: 0=no, 1=yes */ + unsigned int al = 0; /* Posted CAS# additive latency (AL) */ + unsigned int dic = 1; /* Output driver impedance, 34ohm */ + unsigned int dll_en = 0; /* DLL Enable 0=Enable (Normal), + 1=Disable (Test/Debug) */ + + /* Mode Register - MR0 */ + unsigned int dll_on; /* DLL control for precharge PD, 0=off, 1=on */ + unsigned int wr; /* Write Recovery */ + unsigned int dll_rst; /* DLL Reset */ + unsigned int mode; /* Normal=0 or Test=1 */ + unsigned int caslat = 4;/* CAS# latency, default set as 6 cycles */ + /* BT: Burst Type (0=Nibble Sequential, 1=Interleaved) */ + unsigned int bt; + unsigned int bl; /* BL: Burst Length */ + + unsigned int wr_mclk; + + const unsigned int mclk_ps = get_memory_clk_period_ps(); + + rtt = fsl_ddr_get_rtt(); + if (popts->rtt_override) + rtt = popts->rtt_override_value; + + if (additive_latency == (cas_latency - 1)) + al = 1; + if (additive_latency == (cas_latency - 2)) + al = 2; + + /* + * The esdmode value will also be used for writing + * MR1 during write leveling for DDR3, although the + * bits specifically related to the write leveling + * scheme will be handled automatically by the DDR + * controller. so we set the wrlvl_en = 0 here. + */ + esdmode = (0 + | ((qoff & 0x1) << 12) + | ((tdqs_en & 0x1) << 11) + | ((rtt & 0x4) << 7) /* rtt field is split */ + | ((wrlvl_en & 0x1) << 7) + | ((rtt & 0x2) << 5) /* rtt field is split */ + | ((dic & 0x2) << 4) /* DIC field is split */ + | ((al & 0x3) << 3) + | ((rtt & 0x1) << 2) /* rtt field is split */ + | ((dic & 0x1) << 1) /* DIC field is split */ + | ((dll_en & 0x1) << 0) + ); + + /* + * DLL control for precharge PD + * 0=slow exit DLL off (tXPDLL) + * 1=fast exit DLL on (tXP) + */ + dll_on = 1; + wr_mclk = (common_dimm->tWR_ps + mclk_ps - 1) / mclk_ps; + if (wr_mclk >= 12) + wr = 6; + else if (wr_mclk >= 9) + wr = 5; + else + wr = wr_mclk - 4; + dll_rst = 0; /* dll no reset */ + mode = 0; /* normal mode */ + + /* look up table to get the cas latency bits */ + if (cas_latency >= 5 && cas_latency <= 11) { + unsigned char cas_latency_table[7] = { + 0x2, /* 5 clocks */ + 0x4, /* 6 clocks */ + 0x6, /* 7 clocks */ + 0x8, /* 8 clocks */ + 0xa, /* 9 clocks */ + 0xc, /* 10 clocks */ + 0xe /* 11 clocks */ + }; + caslat = cas_latency_table[cas_latency - 5]; + } + bt = 0; /* Nibble sequential */ + + switch (popts->burst_length) { + case DDR_BL8: + bl = 0; + break; + case DDR_OTF: + bl = 1; + break; + case DDR_BC4: + bl = 2; + break; + default: + printf("Error: invalid burst length of %u specified. " + " Defaulting to on-the-fly BC4 or BL8 beats.\n", + popts->burst_length); + bl = 1; + break; + } + + sdmode = (0 + | ((dll_on & 0x1) << 12) + | ((wr & 0x7) << 9) + | ((dll_rst & 0x1) << 8) + | ((mode & 0x1) << 7) + | (((caslat >> 1) & 0x7) << 4) + | ((bt & 0x1) << 3) + | ((bl & 0x3) << 0) + ); + + ddr->ddr_sdram_mode = (0 + | ((esdmode & 0xFFFF) << 16) + | ((sdmode & 0xFFFF) << 0) + ); + + debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode); +} + +#else /* !CONFIG_FSL_DDR3 */ + +/* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */ +static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, + const common_timing_params_t *common_dimm, + unsigned int cas_latency, + unsigned int additive_latency) +{ + unsigned short esdmode; /* Extended SDRAM mode */ + unsigned short sdmode; /* SDRAM mode */ + + /* + * FIXME: This ought to be pre-calculated in a + * technology-specific routine, + * e.g. compute_DDR2_mode_register(), and then the + * sdmode and esdmode passed in as part of common_dimm. + */ + + /* Extended Mode Register */ + unsigned int mrs = 0; /* Mode Register Set */ + unsigned int outputs = 0; /* 0=Enabled, 1=Disabled */ + unsigned int rdqs_en = 0; /* RDQS Enable: 0=no, 1=yes */ + unsigned int dqs_en = 0; /* DQS# Enable: 0=enable, 1=disable */ + unsigned int ocd = 0; /* 0x0=OCD not supported, + 0x7=OCD default state */ + unsigned int rtt; + unsigned int al; /* Posted CAS# additive latency (AL) */ + unsigned int ods = 0; /* Output Drive Strength: + 0 = Full strength (18ohm) + 1 = Reduced strength (4ohm) */ + unsigned int dll_en = 0; /* DLL Enable 0=Enable (Normal), + 1=Disable (Test/Debug) */ + + /* Mode Register (MR) */ + unsigned int mr; /* Mode Register Definition */ + unsigned int pd; /* Power-Down Mode */ + unsigned int wr; /* Write Recovery */ + unsigned int dll_res; /* DLL Reset */ + unsigned int mode; /* Normal=0 or Test=1 */ + unsigned int caslat = 0;/* CAS# latency */ + /* BT: Burst Type (0=Sequential, 1=Interleaved) */ + unsigned int bt; + unsigned int bl; /* BL: Burst Length */ + +#if defined(CONFIG_FSL_DDR2) + const unsigned int mclk_ps = get_memory_clk_period_ps(); +#endif + + rtt = fsl_ddr_get_rtt(); + + al = additive_latency; + + esdmode = (0 + | ((mrs & 0x3) << 14) + | ((outputs & 0x1) << 12) + | ((rdqs_en & 0x1) << 11) + | ((dqs_en & 0x1) << 10) + | ((ocd & 0x7) << 7) + | ((rtt & 0x2) << 5) /* rtt field is split */ + | ((al & 0x7) << 3) + | ((rtt & 0x1) << 2) /* rtt field is split */ + | ((ods & 0x1) << 1) + | ((dll_en & 0x1) << 0) + ); + + mr = 0; /* FIXME: CHECKME */ + + /* + * 0 = Fast Exit (Normal) + * 1 = Slow Exit (Low Power) + */ + pd = 0; + +#if defined(CONFIG_FSL_DDR1) + wr = 0; /* Historical */ +#elif defined(CONFIG_FSL_DDR2) + wr = (common_dimm->tWR_ps + mclk_ps - 1) / mclk_ps - 1; +#endif + dll_res = 0; + mode = 0; + +#if defined(CONFIG_FSL_DDR1) + if (1 <= cas_latency && cas_latency <= 4) { + unsigned char mode_caslat_table[4] = { + 0x5, /* 1.5 clocks */ + 0x2, /* 2.0 clocks */ + 0x6, /* 2.5 clocks */ + 0x3 /* 3.0 clocks */ + }; + caslat = mode_caslat_table[cas_latency - 1]; + } else { + printf("Warning: unknown cas_latency %d\n", cas_latency); + } +#elif defined(CONFIG_FSL_DDR2) + caslat = cas_latency; +#endif + bt = 0; + + switch (popts->burst_length) { + case DDR_BL4: + bl = 2; + break; + case DDR_BL8: + bl = 3; + break; + default: + printf("Error: invalid burst length of %u specified. " + " Defaulting to 4 beats.\n", + popts->burst_length); + bl = 2; + break; + } + + sdmode = (0 + | ((mr & 0x3) << 14) + | ((pd & 0x1) << 12) + | ((wr & 0x7) << 9) + | ((dll_res & 0x1) << 8) + | ((mode & 0x1) << 7) + | ((caslat & 0x7) << 4) + | ((bt & 0x1) << 3) + | ((bl & 0x7) << 0) + ); + + ddr->ddr_sdram_mode = (0 + | ((esdmode & 0xFFFF) << 16) + | ((sdmode & 0xFFFF) << 0) + ); + debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode); +} +#endif + +/* DDR SDRAM Data Initialization (DDR_DATA_INIT) */ +static void set_ddr_data_init(fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int init_value; /* Initialization value */ + + init_value = 0xDEADBEEF; + ddr->ddr_data_init = init_value; +} + +/* + * DDR SDRAM Clock Control (DDR_SDRAM_CLK_CNTL) + * The old controller on the 8540/60 doesn't have this register. + * Hope it's OK to set it (to 0) anyway. + */ +static void set_ddr_sdram_clk_cntl(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts) +{ + unsigned int clk_adjust; /* Clock adjust */ + + clk_adjust = popts->clk_adjust; + ddr->ddr_sdram_clk_cntl = (clk_adjust & 0xF) << 23; +} + +/* DDR Initialization Address (DDR_INIT_ADDR) */ +static void set_ddr_init_addr(fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int init_addr = 0; /* Initialization address */ + + ddr->ddr_init_addr = init_addr; +} + +/* DDR Initialization Address (DDR_INIT_EXT_ADDR) */ +static void set_ddr_init_ext_addr(fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int uia = 0; /* Use initialization address */ + unsigned int init_ext_addr = 0; /* Initialization address */ + + ddr->ddr_init_ext_addr = (0 + | ((uia & 0x1) << 31) + | (init_ext_addr & 0xF) + ); +} + +/* DDR SDRAM Timing Configuration 4 (TIMING_CFG_4) */ +static void set_timing_cfg_4(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts) +{ + unsigned int rwt = 0; /* Read-to-write turnaround for same CS */ + unsigned int wrt = 0; /* Write-to-read turnaround for same CS */ + unsigned int rrt = 0; /* Read-to-read turnaround for same CS */ + unsigned int wwt = 0; /* Write-to-write turnaround for same CS */ + unsigned int dll_lock = 0; /* DDR SDRAM DLL Lock Time */ + +#if defined(CONFIG_FSL_DDR3) + if (popts->burst_length == DDR_BL8) { + /* We set BL/2 for fixed BL8 */ + rrt = 0; /* BL/2 clocks */ + wwt = 0; /* BL/2 clocks */ + } else { + /* We need to set BL/2 + 2 to BC4 and OTF */ + rrt = 2; /* BL/2 + 2 clocks */ + wwt = 2; /* BL/2 + 2 clocks */ + } + dll_lock = 1; /* tDLLK = 512 clocks from spec */ +#endif + ddr->timing_cfg_4 = (0 + | ((rwt & 0xf) << 28) + | ((wrt & 0xf) << 24) + | ((rrt & 0xf) << 20) + | ((wwt & 0xf) << 16) + | (dll_lock & 0x3) + ); + debug("FSLDDR: timing_cfg_4 = 0x%08x\n", ddr->timing_cfg_4); +} + +/* DDR SDRAM Timing Configuration 5 (TIMING_CFG_5) */ +static void set_timing_cfg_5(fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int rodt_on = 0; /* Read to ODT on */ + unsigned int rodt_off = 0; /* Read to ODT off */ + unsigned int wodt_on = 0; /* Write to ODT on */ + unsigned int wodt_off = 0; /* Write to ODT off */ + +#if defined(CONFIG_FSL_DDR3) + rodt_on = 3; /* 2 clocks */ + rodt_off = 4; /* 4 clocks */ + wodt_on = 2; /* 1 clocks */ + wodt_off = 4; /* 4 clocks */ +#endif + + ddr->timing_cfg_5 = (0 + | ((rodt_on & 0x1f) << 24) + | ((rodt_off & 0x7) << 20) + | ((wodt_on & 0x1f) << 12) + | ((wodt_off & 0x7) << 8) + ); + debug("FSLDDR: timing_cfg_5 = 0x%08x\n", ddr->timing_cfg_5); +} + +/* DDR ZQ Calibration Control (DDR_ZQ_CNTL) */ +static void set_ddr_zq_cntl(fsl_ddr_cfg_regs_t *ddr, unsigned int zq_en) +{ + unsigned int zqinit = 0;/* POR ZQ Calibration Time (tZQinit) */ + /* Normal Operation Full Calibration Time (tZQoper) */ + unsigned int zqoper = 0; + /* Normal Operation Short Calibration Time (tZQCS) */ + unsigned int zqcs = 0; + + if (zq_en) { + zqinit = 9; /* 512 clocks */ + zqoper = 8; /* 256 clocks */ + zqcs = 6; /* 64 clocks */ + } + + ddr->ddr_zq_cntl = (0 + | ((zq_en & 0x1) << 31) + | ((zqinit & 0xF) << 24) + | ((zqoper & 0xF) << 16) + | ((zqcs & 0xF) << 8) + ); +} + +/* DDR Write Leveling Control (DDR_WRLVL_CNTL) */ +static void set_ddr_wrlvl_cntl(fsl_ddr_cfg_regs_t *ddr, unsigned int wrlvl_en, + const memctl_options_t *popts) +{ + /* + * First DQS pulse rising edge after margining mode + * is programmed (tWL_MRD) + */ + unsigned int wrlvl_mrd = 0; + /* ODT delay after margining mode is programmed (tWL_ODTEN) */ + unsigned int wrlvl_odten = 0; + /* DQS/DQS_ delay after margining mode is programmed (tWL_DQSEN) */ + unsigned int wrlvl_dqsen = 0; + /* WRLVL_SMPL: Write leveling sample time */ + unsigned int wrlvl_smpl = 0; + /* WRLVL_WLR: Write leveling repeition time */ + unsigned int wrlvl_wlr = 0; + /* WRLVL_START: Write leveling start time */ + unsigned int wrlvl_start = 0; + + /* suggest enable write leveling for DDR3 due to fly-by topology */ + if (wrlvl_en) { + /* tWL_MRD min = 40 nCK, we set it 64 */ + wrlvl_mrd = 0x6; + /* tWL_ODTEN 128 */ + wrlvl_odten = 0x7; + /* tWL_DQSEN min = 25 nCK, we set it 32 */ + wrlvl_dqsen = 0x5; + /* + * Write leveling sample time at least need 6 clocks + * higher than tWLO to allow enough time for progagation + * delay and sampling the prime data bits. + */ + wrlvl_smpl = 0xf; + /* + * Write leveling repetition time + * at least tWLO + 6 clocks clocks + * we set it 32 + */ + wrlvl_wlr = 0x5; + /* + * Write leveling start time + * The value use for the DQS_ADJUST for the first sample + * when write leveling is enabled. + */ + wrlvl_start = 0x8; + /* + * Override the write leveling sample and start time + * according to specific board + */ + if (popts->wrlvl_override) { + wrlvl_smpl = popts->wrlvl_sample; + wrlvl_start = popts->wrlvl_start; + } + } + + ddr->ddr_wrlvl_cntl = (0 + | ((wrlvl_en & 0x1) << 31) + | ((wrlvl_mrd & 0x7) << 24) + | ((wrlvl_odten & 0x7) << 20) + | ((wrlvl_dqsen & 0x7) << 16) + | ((wrlvl_smpl & 0xf) << 12) + | ((wrlvl_wlr & 0x7) << 8) + | ((wrlvl_start & 0x1F) << 0) + ); +} + +/* DDR Self Refresh Counter (DDR_SR_CNTR) */ +static void set_ddr_sr_cntr(fsl_ddr_cfg_regs_t *ddr, unsigned int sr_it) +{ + /* Self Refresh Idle Threshold */ + ddr->ddr_sr_cntr = (sr_it & 0xF) << 16; +} + +/* DDR SDRAM Register Control Word 1 (DDR_SDRAM_RCW_1) */ +static void set_ddr_sdram_rcw_1(fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int rcw0 = 0; /* RCW0: Register Control Word 0 */ + unsigned int rcw1 = 0; /* RCW1: Register Control Word 1 */ + unsigned int rcw2 = 0; /* RCW2: Register Control Word 2 */ + unsigned int rcw3 = 0; /* RCW3: Register Control Word 3 */ + unsigned int rcw4 = 0; /* RCW4: Register Control Word 4 */ + unsigned int rcw5 = 0; /* RCW5: Register Control Word 5 */ + unsigned int rcw6 = 0; /* RCW6: Register Control Word 6 */ + unsigned int rcw7 = 0; /* RCW7: Register Control Word 7 */ + + ddr->ddr_sdram_rcw_1 = (0 + | ((rcw0 & 0xF) << 28) + | ((rcw1 & 0xF) << 24) + | ((rcw2 & 0xF) << 20) + | ((rcw3 & 0xF) << 16) + | ((rcw4 & 0xF) << 12) + | ((rcw5 & 0xF) << 8) + | ((rcw6 & 0xF) << 4) + | ((rcw7 & 0xF) << 0) + ); +} + +/* DDR SDRAM Register Control Word 2 (DDR_SDRAM_RCW_2) */ +static void set_ddr_sdram_rcw_2(fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int rcw8 = 0; /* RCW0: Register Control Word 8 */ + unsigned int rcw9 = 0; /* RCW1: Register Control Word 9 */ + unsigned int rcw10 = 0; /* RCW2: Register Control Word 10 */ + unsigned int rcw11 = 0; /* RCW3: Register Control Word 11 */ + unsigned int rcw12 = 0; /* RCW4: Register Control Word 12 */ + unsigned int rcw13 = 0; /* RCW5: Register Control Word 13 */ + unsigned int rcw14 = 0; /* RCW6: Register Control Word 14 */ + unsigned int rcw15 = 0; /* RCW7: Register Control Word 15 */ + + ddr->ddr_sdram_rcw_2 = (0 + | ((rcw8 & 0xF) << 28) + | ((rcw9 & 0xF) << 24) + | ((rcw10 & 0xF) << 20) + | ((rcw11 & 0xF) << 16) + | ((rcw12 & 0xF) << 12) + | ((rcw13 & 0xF) << 8) + | ((rcw14 & 0xF) << 4) + | ((rcw15 & 0xF) << 0) + ); +} + +unsigned int +check_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr) +{ + unsigned int res = 0; + + /* + * Check that DDR_SDRAM_CFG[RD_EN] and DDR_SDRAM_CFG[2T_EN] are + * not set at the same time. + */ + if (ddr->ddr_sdram_cfg & 0x10000000 + && ddr->ddr_sdram_cfg & 0x00008000) { + printf("Error: DDR_SDRAM_CFG[RD_EN] and DDR_SDRAM_CFG[2T_EN] " + " should not be set at the same time.\n"); + res++; + } + + return res; +} + +unsigned int +compute_fsl_memctl_config_regs(const memctl_options_t *popts, + fsl_ddr_cfg_regs_t *ddr, + const common_timing_params_t *common_dimm, + const dimm_params_t *dimm_params, + unsigned int dbw_cap_adj) +{ + unsigned int i; + unsigned int cas_latency; + unsigned int additive_latency; + unsigned int sr_it; + unsigned int zq_en; + unsigned int wrlvl_en; + + memset(ddr, 0, sizeof(fsl_ddr_cfg_regs_t)); + + if (common_dimm == NULL) { + printf("Error: subset DIMM params struct null pointer\n"); + return 1; + } + + /* + * Process overrides first. + * + * FIXME: somehow add dereated caslat to this + */ + cas_latency = (popts->cas_latency_override) + ? popts->cas_latency_override_value + : common_dimm->lowest_common_SPD_caslat; + + additive_latency = (popts->additive_latency_override) + ? popts->additive_latency_override_value + : common_dimm->additive_latency; + + sr_it = (popts->auto_self_refresh_en) + ? popts->sr_it + : 0; + /* ZQ calibration */ + zq_en = (popts->zq_en) ? 1 : 0; + /* write leveling */ + wrlvl_en = (popts->wrlvl_en) ? 1 : 0; + + /* Chip Select Memory Bounds (CSn_BNDS) */ + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + unsigned long long ea = 0, sa = 0; + + if (popts->ba_intlv_ctl && (i > 0) && + ((popts->ba_intlv_ctl & 0x60) != FSL_DDR_CS2_CS3 )) { + /* Don't set up boundaries for other CS + * other than CS0, if bank interleaving + * is enabled and not CS2+CS3 interleaved. + * But we need to set the ODT_RD_CFG and + * ODT_WR_CFG for CS1_CONFIG here. + */ + set_csn_config(i, ddr, popts, dimm_params); + break; + } + + if (dimm_params[i/2].n_ranks == 0) { + debug("Skipping setup of CS%u " + "because n_ranks on DIMM %u is 0\n", i, i/2); + continue; + } + if (popts->memctl_interleaving && popts->ba_intlv_ctl) { + /* + * This works superbank 2CS + * There are 2 memory controllers configured + * identically, memory is interleaved between them, + * and each controller uses rank interleaving within + * itself. Therefore the starting and ending address + * on each controller is twice the amount present on + * each controller. + */ + unsigned long long rank_density + = dimm_params[0].capacity; + ea = (2 * (rank_density >> dbw_cap_adj)) - 1; + } + else if (!popts->memctl_interleaving && popts->ba_intlv_ctl) { + /* + * If memory interleaving between controllers is NOT + * enabled, the starting address for each memory + * controller is distinct. However, because rank + * interleaving is enabled, the starting and ending + * addresses of the total memory on that memory + * controller needs to be programmed into its + * respective CS0_BNDS. + */ + unsigned long long rank_density + = dimm_params[i/2].rank_density; + switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) { + case FSL_DDR_CS0_CS1_CS2_CS3: + /* CS0+CS1+CS2+CS3 interleaving, only CS0_CNDS + * needs to be set. + */ + sa = common_dimm->base_address; + ea = sa + (4 * (rank_density >> dbw_cap_adj))-1; + break; + case FSL_DDR_CS0_CS1_AND_CS2_CS3: + /* CS0+CS1 and CS2+CS3 interleaving, CS0_CNDS + * and CS2_CNDS need to be set. + */ + if (!(i&1)) { + sa = dimm_params[i/2].base_address; + ea = sa + (i * (rank_density >> + dbw_cap_adj)) - 1; + } + break; + case FSL_DDR_CS0_CS1: + /* CS0+CS1 interleaving, CS0_CNDS needs + * to be set + */ + sa = common_dimm->base_address; + ea = sa + (2 * (rank_density >> dbw_cap_adj))-1; + break; + case FSL_DDR_CS2_CS3: + /* CS2+CS3 interleaving*/ + if (i == 2) { + sa = dimm_params[i/2].base_address; + ea = sa + (2 * (rank_density >> + dbw_cap_adj)) - 1; + } + break; + default: /* No bank(chip-select) interleaving */ + break; + } + } + else if (popts->memctl_interleaving && !popts->ba_intlv_ctl) { + /* + * Only the rank on CS0 of each memory controller may + * be used if memory controller interleaving is used + * without rank interleaving within each memory + * controller. However, the ending address programmed + * into each CS0 must be the sum of the amount of + * memory in the two CS0 ranks. + */ + if (i == 0) { + unsigned long long rank_density + = dimm_params[0].rank_density; + ea = (2 * (rank_density >> dbw_cap_adj)) - 1; + } + + } + else if (!popts->memctl_interleaving && !popts->ba_intlv_ctl) { + /* + * No rank interleaving and no memory controller + * interleaving. + */ + unsigned long long rank_density + = dimm_params[i/2].rank_density; + sa = dimm_params[i/2].base_address; + ea = sa + (rank_density >> dbw_cap_adj) - 1; + if (i&1) { + if ((dimm_params[i/2].n_ranks == 1)) { + /* Odd chip select, single-rank dimm */ + sa = 0; + ea = 0; + } else { + /* Odd chip select, dual-rank DIMM */ + sa += rank_density >> dbw_cap_adj; + ea += rank_density >> dbw_cap_adj; + } + } + } + + sa >>= 24; + ea >>= 24; + + ddr->cs[i].bnds = (0 + | ((sa & 0xFFF) << 16) /* starting address MSB */ + | ((ea & 0xFFF) << 0) /* ending address MSB */ + ); + + debug("FSLDDR: cs[%d]_bnds = 0x%08x\n", i, ddr->cs[i].bnds); + set_csn_config(i, ddr, popts, dimm_params); + set_csn_config_2(i, ddr); + } + +#if !defined(CONFIG_FSL_DDR1) + set_timing_cfg_0(ddr); +#endif + + set_timing_cfg_3(ddr, common_dimm, cas_latency); + set_timing_cfg_1(ddr, popts, common_dimm, cas_latency); + set_timing_cfg_2(ddr, popts, common_dimm, + cas_latency, additive_latency); + + set_ddr_sdram_cfg(ddr, popts, common_dimm); + + set_ddr_sdram_cfg_2(ddr, popts); + set_ddr_sdram_mode(ddr, popts, common_dimm, + cas_latency, additive_latency); + set_ddr_sdram_mode_2(ddr, popts); + set_ddr_sdram_interval(ddr, popts, common_dimm); + set_ddr_data_init(ddr); + set_ddr_sdram_clk_cntl(ddr, popts); + set_ddr_init_addr(ddr); + set_ddr_init_ext_addr(ddr); + set_timing_cfg_4(ddr, popts); + set_timing_cfg_5(ddr); + + set_ddr_zq_cntl(ddr, zq_en); + set_ddr_wrlvl_cntl(ddr, wrlvl_en, popts); + + set_ddr_sr_cntr(ddr, sr_it); + + set_ddr_sdram_rcw_1(ddr); + set_ddr_sdram_rcw_2(ddr); + + return check_fsl_memctl_config_regs(ddr); +} |
