diff options
Diffstat (limited to 'arch/powerpc/cpu/mpc8xx/cpu_init.c')
| -rw-r--r-- | arch/powerpc/cpu/mpc8xx/cpu_init.c | 285 |
1 files changed, 285 insertions, 0 deletions
diff --git a/arch/powerpc/cpu/mpc8xx/cpu_init.c b/arch/powerpc/cpu/mpc8xx/cpu_init.c new file mode 100644 index 0000000000..eb0091bdb3 --- /dev/null +++ b/arch/powerpc/cpu/mpc8xx/cpu_init.c @@ -0,0 +1,285 @@ +/* + * (C) Copyright 2000-2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <watchdog.h> + +#include <mpc8xx.h> +#include <commproc.h> + +#if defined(CONFIG_SYS_RTCSC) || defined(CONFIG_SYS_RMDS) +DECLARE_GLOBAL_DATA_PTR; +#endif + +#if defined(CONFIG_SYS_I2C_UCODE_PATCH) || defined(CONFIG_SYS_SPI_UCODE_PATCH) || \ + defined(CONFIG_SYS_SMC_UCODE_PATCH) +void cpm_load_patch (volatile immap_t * immr); +#endif + +/* + * Breath some life into the CPU... + * + * Set up the memory map, + * initialize a bunch of registers, + * initialize the UPM's + */ +void cpu_init_f (volatile immap_t * immr) +{ +#ifndef CONFIG_MBX + volatile memctl8xx_t *memctl = &immr->im_memctl; +# ifdef CONFIG_SYS_PLPRCR + ulong mfmask; +# endif +#endif + ulong reg; + + /* SYPCR - contains watchdog control (11-9) */ + + immr->im_siu_conf.sc_sypcr = CONFIG_SYS_SYPCR; + +#if defined(CONFIG_WATCHDOG) + reset_8xx_watchdog (immr); +#endif /* CONFIG_WATCHDOG */ + + /* SIUMCR - contains debug pin configuration (11-6) */ +#ifndef CONFIG_SVM_SC8xx + immr->im_siu_conf.sc_siumcr |= CONFIG_SYS_SIUMCR; +#else + immr->im_siu_conf.sc_siumcr = CONFIG_SYS_SIUMCR; +#endif + /* initialize timebase status and control register (11-26) */ + /* unlock TBSCRK */ + + immr->im_sitk.sitk_tbscrk = KAPWR_KEY; + immr->im_sit.sit_tbscr = CONFIG_SYS_TBSCR; + + /* initialize the PIT (11-31) */ + + immr->im_sitk.sitk_piscrk = KAPWR_KEY; + immr->im_sit.sit_piscr = CONFIG_SYS_PISCR; + + /* System integration timers. Don't change EBDF! (15-27) */ + + immr->im_clkrstk.cark_sccrk = KAPWR_KEY; + reg = immr->im_clkrst.car_sccr; + reg &= SCCR_MASK; + reg |= CONFIG_SYS_SCCR; + immr->im_clkrst.car_sccr = reg; + + /* PLL (CPU clock) settings (15-30) */ + + immr->im_clkrstk.cark_plprcrk = KAPWR_KEY; + +#ifndef CONFIG_MBX /* MBX board does things different */ + + /* If CONFIG_SYS_PLPRCR (set in the various *_config.h files) tries to + * set the MF field, then just copy CONFIG_SYS_PLPRCR over car_plprcr, + * otherwise OR in CONFIG_SYS_PLPRCR so we do not change the current MF + * field value. + * + * For newer (starting MPC866) chips PLPRCR layout is different. + */ +#ifdef CONFIG_SYS_PLPRCR + if (get_immr(0xFFFF) >= MPC8xx_NEW_CLK) + mfmask = PLPRCR_MFACT_MSK; + else + mfmask = PLPRCR_MF_MSK; + + if ((CONFIG_SYS_PLPRCR & mfmask) != 0) + reg = CONFIG_SYS_PLPRCR; /* reset control bits */ + else { + reg = immr->im_clkrst.car_plprcr; + reg &= mfmask; /* isolate MF-related fields */ + reg |= CONFIG_SYS_PLPRCR; /* reset control bits */ + } + immr->im_clkrst.car_plprcr = reg; +#endif + + /* + * Memory Controller: + */ + + /* perform BR0 reset that MPC850 Rev. A can't guarantee */ + reg = memctl->memc_br0; + reg &= BR_PS_MSK; /* Clear everything except Port Size bits */ + reg |= BR_V; /* then add just the "Bank Valid" bit */ + memctl->memc_br0 = reg; + + /* Map banks 0 (and maybe 1) to the FLASH banks 0 (and 1) at + * preliminary addresses - these have to be modified later + * when FLASH size has been determined + * + * Depending on the size of the memory region defined by + * CONFIG_SYS_OR0_REMAP some boards (wide address mask) allow to map the + * CONFIG_SYS_MONITOR_BASE, while others (narrower address mask) can't + * map CONFIG_SYS_MONITOR_BASE. + * + * For example, for CONFIG_IVMS8, the CONFIG_SYS_MONITOR_BASE is + * 0xff000000, but CONFIG_SYS_OR0_REMAP's address mask is 0xfff80000. + * + * If BR0 wasn't loaded with address base 0xff000000, then BR0's + * base address remains as 0x00000000. However, the address mask + * have been narrowed to 512Kb, so CONFIG_SYS_MONITOR_BASE wasn't mapped + * into the Bank0. + * + * This is why CONFIG_IVMS8 and similar boards must load BR0 with + * CONFIG_SYS_BR0_PRELIM in advance. + * + * [Thanks to Michael Liao for this explanation. + * I owe him a free beer. - wd] + */ + +#if defined(CONFIG_GTH) || \ + defined(CONFIG_HERMES) || \ + defined(CONFIG_ICU862) || \ + defined(CONFIG_IP860) || \ + defined(CONFIG_IVML24) || \ + defined(CONFIG_IVMS8) || \ + defined(CONFIG_LWMON) || \ + defined(CONFIG_MHPC) || \ + defined(CONFIG_PCU_E) || \ + defined(CONFIG_R360MPI) || \ + defined(CONFIG_RMU) || \ + defined(CONFIG_RPXCLASSIC) || \ + defined(CONFIG_RPXLITE) || \ + defined(CONFIG_SPC1920) || \ + defined(CONFIG_SPD823TS) + + memctl->memc_br0 = CONFIG_SYS_BR0_PRELIM; +#endif + +#if defined(CONFIG_SYS_OR0_REMAP) + memctl->memc_or0 = CONFIG_SYS_OR0_REMAP; +#endif +#if defined(CONFIG_SYS_OR1_REMAP) + memctl->memc_or1 = CONFIG_SYS_OR1_REMAP; +#endif +#if defined(CONFIG_SYS_OR5_REMAP) + memctl->memc_or5 = CONFIG_SYS_OR5_REMAP; +#endif + + /* now restrict to preliminary range */ + memctl->memc_br0 = CONFIG_SYS_BR0_PRELIM; + memctl->memc_or0 = CONFIG_SYS_OR0_PRELIM; + +#if (defined(CONFIG_SYS_OR1_PRELIM) && defined(CONFIG_SYS_BR1_PRELIM)) + memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM; + memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM; +#endif + +#if defined(CONFIG_IP860) /* disable CS0 now that Flash is mapped on CS1 */ + memctl->memc_br0 = 0; +#endif + +#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM) + memctl->memc_or2 = CONFIG_SYS_OR2_PRELIM; + memctl->memc_br2 = CONFIG_SYS_BR2_PRELIM; +#endif + +#if defined(CONFIG_SYS_OR3_PRELIM) && defined(CONFIG_SYS_BR3_PRELIM) + memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM; + memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM; +#endif + +#if defined(CONFIG_SYS_OR4_PRELIM) && defined(CONFIG_SYS_BR4_PRELIM) + memctl->memc_or4 = CONFIG_SYS_OR4_PRELIM; + memctl->memc_br4 = CONFIG_SYS_BR4_PRELIM; +#endif + +#if defined(CONFIG_SYS_OR5_PRELIM) && defined(CONFIG_SYS_BR5_PRELIM) + memctl->memc_or5 = CONFIG_SYS_OR5_PRELIM; + memctl->memc_br5 = CONFIG_SYS_BR5_PRELIM; +#endif + +#if defined(CONFIG_SYS_OR6_PRELIM) && defined(CONFIG_SYS_BR6_PRELIM) + memctl->memc_or6 = CONFIG_SYS_OR6_PRELIM; + memctl->memc_br6 = CONFIG_SYS_BR6_PRELIM; +#endif + +#if defined(CONFIG_SYS_OR7_PRELIM) && defined(CONFIG_SYS_BR7_PRELIM) + memctl->memc_or7 = CONFIG_SYS_OR7_PRELIM; + memctl->memc_br7 = CONFIG_SYS_BR7_PRELIM; +#endif + +#endif /* ! CONFIG_MBX */ + + /* + * Reset CPM + */ + immr->im_cpm.cp_cpcr = CPM_CR_RST | CPM_CR_FLG; + do { /* Spin until command processed */ + __asm__ ("eieio"); + } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG); + +#ifdef CONFIG_MBX + /* + * on the MBX, things are a little bit different: + * - we need to read the VPD to get board information + * - the plprcr is set up dynamically + * - the memory controller is set up dynamically + */ + mbx_init (); +#endif /* CONFIG_MBX */ + +#ifdef CONFIG_RPXCLASSIC + rpxclassic_init (); +#endif + +#if defined(CONFIG_RPXLITE) && defined(CONFIG_ENV_IS_IN_NVRAM) + rpxlite_init (); +#endif + +#ifdef CONFIG_SYS_RCCR /* must be done before cpm_load_patch() */ + /* write config value */ + immr->im_cpm.cp_rccr = CONFIG_SYS_RCCR; +#endif + +#if defined(CONFIG_SYS_I2C_UCODE_PATCH) || defined(CONFIG_SYS_SPI_UCODE_PATCH) || \ + defined(CONFIG_SYS_SMC_UCODE_PATCH) + cpm_load_patch (immr); /* load mpc8xx microcode patch */ +#endif +} + +/* + * initialize higher level parts of CPU like timers + */ +int cpu_init_r (void) +{ +#if defined(CONFIG_SYS_RTCSC) || defined(CONFIG_SYS_RMDS) + bd_t *bd = gd->bd; + volatile immap_t *immr = (volatile immap_t *) (bd->bi_immr_base); +#endif + +#ifdef CONFIG_SYS_RTCSC + /* Unlock RTSC register */ + immr->im_sitk.sitk_rtcsck = KAPWR_KEY; + /* write config value */ + immr->im_sit.sit_rtcsc = CONFIG_SYS_RTCSC; +#endif + +#ifdef CONFIG_SYS_RMDS + /* write config value */ + immr->im_cpm.cp_rmds = CONFIG_SYS_RMDS; +#endif + return (0); +} |
