diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 101 |
1 files changed, 82 insertions, 19 deletions
@@ -54,6 +54,11 @@ In case of problems see the CHANGELOG and CREDITS files to find out who contributed the specific port. The MAINTAINERS file lists board maintainers. +Note: There is no CHANGELOG file in the actual U-Boot source tree; +it can be created dynamically from the Git log using: + + make CHANGELOG + Where to get help: ================== @@ -1409,6 +1414,13 @@ CBFS (Coreboot Filesystem) support boot. See the documentation file README.video for a description of this variable. + CONFIG_VIDEO_VGA + + Enable the VGA video / BIOS for x86. The alternative if you + are using coreboot is to use the coreboot frame buffer + driver. + + - Keyboard Support: CONFIG_KEYBOARD @@ -1469,21 +1481,10 @@ CBFS (Coreboot Filesystem) support Normally display is black on white background; define CONFIG_SYS_WHITE_ON_BLACK to get it inverted. + CONFIG_LCD_BMP_RLE8 - CONFIG_LCD_ALIGNMENT - - Normally the LCD is page-aligned (tyically 4KB). If this is - defined then the LCD will be aligned to this value instead. - For ARM it is sometimes useful to use MMU_SECTION_SIZE - here, since it is cheaper to change data cache settings on - a per-section basis. + Support drawing of RLE8-compressed bitmaps on the LCD. - CONFIG_CONSOLE_SCROLL_LINES - - When the console need to be scrolled, this is the number of - lines to scroll by. It defaults to 1. Increasing this makes - the console jump but can help speed up operation when scrolling - is slow. - Splash Screen Support: CONFIG_SPLASH_SCREEN @@ -2211,6 +2212,14 @@ CBFS (Coreboot Filesystem) support HERMES, IP860, RPXlite, LWMON, FLAGADM, TQM8260 +- Access to physical memory region (> 4GB) + Some basic support is provided for operations on memory not + normally accessible to U-Boot - e.g. some architectures + support access to more than 4GB of memory on 32-bit + machines using physical address extension or similar. + Define CONFIG_PHYSMEM to access this basic support, which + currently only supports clearing the memory. + - Error Recovery: CONFIG_PANIC_HANG @@ -2613,6 +2622,17 @@ FIT uImage format: -150 common/cmd_nand.c Incorrect FIT image format 151 common/cmd_nand.c FIT image format OK +- FIT image support: + CONFIG_FIT + Enable support for the FIT uImage format. + + CONFIG_FIT_BEST_MATCH + When no configuration is explicitly selected, default to the + one whose fdt's compatibility field best matches that of + U-Boot itself. A match is considered "best" if it matches the + most specific compatibility entry of U-Boot's fdt's root node. + The order of entries in the configuration's fdt is ignored. + - Standalone program support: CONFIG_STANDALONE_LOAD_ADDR @@ -2664,6 +2684,10 @@ FIT uImage format: CONFIG_SPL_TEXT_BASE TEXT_BASE for linking the SPL binary. + CONFIG_SPL_RELOC_TEXT_BASE + Address to relocate to. If unspecified, this is equal to + CONFIG_SPL_TEXT_BASE (i.e. no relocation is done). + CONFIG_SPL_BSS_START_ADDR Link address for the BSS within the SPL binary. @@ -2673,6 +2697,11 @@ FIT uImage format: CONFIG_SPL_STACK Adress of the start of the stack SPL will use + CONFIG_SPL_RELOC_STACK + Adress of the start of the stack SPL will use after + relocation. If unspecified, this is equal to + CONFIG_SPL_STACK. + CONFIG_SYS_SPL_MALLOC_START Starting address of the malloc pool used in SPL. @@ -2688,6 +2717,9 @@ FIT uImage format: For ARM, enable an optional function to print more information about the running system. + CONFIG_SPL_INIT_MINIMAL + Arch init code should be built for a very small image + CONFIG_SPL_LIBCOMMON_SUPPORT Support for common/libcommon.o in SPL binary @@ -2715,8 +2747,19 @@ FIT uImage format: CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME Filename to read to load U-Boot when reading from FAT + CONFIG_SPL_NAND_BASE + Include nand_base.c in the SPL. Requires + CONFIG_SPL_NAND_DRIVERS. + + CONFIG_SPL_NAND_DRIVERS + SPL uses normal NAND drivers, not minimal drivers. + + CONFIG_SPL_NAND_ECC + Include standard software ECC in the SPL + CONFIG_SPL_NAND_SIMPLE - Support for drivers/mtd/nand/libnand.o in SPL binary + Support for NAND boot using simple NAND drivers that + expose the cmd_ctrl() interface. CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT, CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE, @@ -2724,15 +2767,19 @@ FIT uImage format: CONFIG_SYS_NAND_ECCPOS, CONFIG_SYS_NAND_ECCSIZE, CONFIG_SYS_NAND_ECCBYTES Defines the size and behavior of the NAND that SPL uses - to read U-Boot with CONFIG_SPL_NAND_SIMPLE + to read U-Boot CONFIG_SYS_NAND_U_BOOT_OFFS - Location in NAND for CONFIG_SPL_NAND_SIMPLE to read U-Boot - from. + Location in NAND to read U-Boot from + + CONFIG_SYS_NAND_U_BOOT_DST + Location in memory to load U-Boot to + + CONFIG_SYS_NAND_U_BOOT_SIZE + Size of image to load CONFIG_SYS_NAND_U_BOOT_START - Location in memory for CONFIG_SPL_NAND_SIMPLE to load U-Boot - to. + Entry point in loaded image to jump to CONFIG_SYS_NAND_HW_ECC_OOBFIRST Define this if you need to first read the OOB and then the @@ -2757,6 +2804,11 @@ FIT uImage format: CONFIG_SPL_LIBGENERIC_SUPPORT Support for lib/libgeneric.o in SPL binary + CONFIG_SPL_TARGET + Final target image containing SPL and payload. Some SPLs + use an arch-specific makefile fragment instead, for + example if more than one image needs to be produced. + Modem Support: -------------- @@ -3632,6 +3684,16 @@ Low Level (hardware related) configuration options: be used if available. These functions may be faster under some conditions but may increase the binary size. +- CONFIG_X86_NO_RESET_VECTOR + If defined, the x86 reset vector code is excluded. You will need + to do this when U-Boot is running from Coreboot. + +- CONFIG_X86_NO_REAL_MODE + If defined, x86 real mode code is omitted. This assumes a + 32-bit environment where such code is not needed. You will + need to do this when U-Boot is running from Coreboot. + + Freescale QE/FMAN Firmware Support: ----------------------------------- @@ -3859,6 +3921,7 @@ saveenv - save environment variables to persistent storage protect - enable or disable FLASH write protection erase - erase FLASH memory flinfo - print FLASH memory information +nand - NAND memory operations (see doc/README.nand) bdinfo - print Board Info structure iminfo - print header information for application image coninfo - print console devices and informations |
