diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 43 |
1 files changed, 28 insertions, 15 deletions
@@ -634,14 +634,6 @@ The following options need to be configured: boot loader that has already initialized the UART. Define this variable to flush the UART at init time. - CONFIG_SYS_NS16550_BROKEN_TEMT - - 16550 UART set the Transmitter Empty (TEMT) Bit when all output - has finished and the transmitter is totally empty. U-Boot waits - for this bit to be set to initialize the serial console. On some - broken platforms this bit is not set in SPL making U-Boot to - hang while waiting for TEMT. Define this option to avoid it. - - Console Interface: Depending on board, define exactly one serial port @@ -2839,8 +2831,18 @@ FIT uImage format: CONFIG_SPL_LDSCRIPT LDSCRIPT for linking the SPL binary. + CONFIG_SPL_MAX_FOOTPRINT + Maximum size in memory allocated to the SPL, BSS included. + When defined, the linker checks that the actual memory + used by SPL from _start to __bss_end does not exceed it. + CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE + must not be both defined at the same time. + CONFIG_SPL_MAX_SIZE - Maximum binary size (text, data and rodata) of the SPL binary. + Maximum size of the SPL image (text, data, rodata, and + linker lists sections), BSS excluded. + When defined, the linker checks that the actual size does + not exceed it. CONFIG_SPL_TEXT_BASE TEXT_BASE for linking the SPL binary. @@ -2853,7 +2855,11 @@ FIT uImage format: Link address for the BSS within the SPL binary. CONFIG_SPL_BSS_MAX_SIZE - Maximum binary size of the BSS section of the SPL binary. + Maximum size in memory allocated to the SPL BSS. + When defined, the linker checks that the actual memory used + by SPL from __bss_start to __bss_end does not exceed it. + CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE + must not be both defined at the same time. CONFIG_SPL_STACK Adress of the start of the stack SPL will use @@ -2972,8 +2978,11 @@ FIT uImage format: Support for lib/libgeneric.o in SPL binary CONFIG_SPL_PAD_TO - Linker address to which the SPL should be padded before - appending the SPL payload. + Image offset to which the SPL should be padded before appending + the SPL payload. By default, this is defined as + CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined. + CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL + payload without any padding, or >= CONFIG_SPL_MAX_SIZE. CONFIG_SPL_TARGET Final target image containing SPL and payload. Some SPLs @@ -3846,9 +3855,13 @@ Low Level (hardware related) configuration options: - CONFIG_SYS_SRIOn_MEM_SIZE: Size of SRIO port 'n' memory region -- CONFIG_SYS_NDFC_16 - Defined to tell the NDFC that the NAND chip is using a - 16 bit bus. +- CONFIG_SYS_NAND_BUSWIDTH_16BIT + Defined to tell the NAND controller that the NAND chip is using + a 16 bit bus. + Not all NAND drivers use this symbol. + Example of drivers that use it: + - drivers/mtd/nand/ndfc.c + - drivers/mtd/nand/mxc_nand.c - CONFIG_SYS_NDFC_EBC0_CFG Sets the EBC0_CFG register for the NDFC. If not defined |
