diff options
97 files changed, 2682 insertions, 2999 deletions
@@ -438,6 +438,11 @@ $(obj)u-boot.kwb: $(obj)u-boot.bin $(obj)tools/mkimage -n $(CONFIG_SYS_KWD_CONFIG) -T kwbimage \ -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE) -d $< $@ +$(obj)u-boot.pbl: $(obj)u-boot.bin + $(obj)tools/mkimage -n $(CONFIG_PBLRCW_CONFIG) \ + -R $(CONFIG_PBLPBI_CONFIG) -T pblimage \ + -d $< $@ + $(obj)u-boot.sha1: $(obj)u-boot.bin $(obj)tools/ubsha1 $(obj)u-boot.bin @@ -808,6 +813,7 @@ clobber: tidy $(obj)cscope.* $(obj)*.*~ @rm -f $(obj)u-boot $(obj)u-boot.map $(obj)u-boot.hex $(ALL-y) @rm -f $(obj)u-boot.kwb + @rm -f $(obj)u-boot.pbl @rm -f $(obj)u-boot.imx @rm -f $(obj)u-boot.ubl @rm -f $(obj)u-boot.ais @@ -383,6 +383,31 @@ The following options need to be configured: symbol should be set to the TLB1 entry to be used for this purpose. + CONFIG_SYS_FSL_ERRATUM_A004510 + + Enables a workaround for erratum A004510. If set, + then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and + CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set. + + CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV + CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional) + + Defines one or two SoC revisions (low 8 bits of SVR) + for which the A004510 workaround should be applied. + + The rest of SVR is either not relevant to the decision + of whether the erratum is present (e.g. p2040 versus + p2041) or is implied by the build target, which controls + whether CONFIG_SYS_FSL_ERRATUM_A004510 is set. + + See Freescale App Note 4493 for more information about + this erratum. + + CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY + + This is the value to write into CCSR offset 0x18600 + according to the A004510 workaround. + - Generic CPU options: CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN @@ -3100,12 +3125,12 @@ to save the current settings. These two #defines specify the address and size of the environment area within the remote memory space. The local device can get the environment from remote memory - space by SRIO or other links. + space by SRIO or PCIE links. BE CAREFUL! For some special cases, the local device can not use "saveenv" command. For example, the local device will get the -environment stored in a remote NOR flash by SRIO link, but it can -not erase, write this NOR flash by SRIO interface. +environment stored in a remote NOR flash by SRIO or PCIE link, +but it can not erase, write this NOR flash by SRIO or PCIE interface. - CONFIG_ENV_IS_IN_NAND: @@ -3553,9 +3578,9 @@ within that device. - CONFIG_SYS_QE_FMAN_FW_IN_REMOTE Specifies that QE/FMAN firmware is located in the remote (master) memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which - can be mapped from slave TLB->slave LAW->slave SRIO outbound window - ->master inbound window->master LAW->the ucode address in master's - NOR flash. + can be mapped from slave TLB->slave LAW->slave SRIO or PCIE outbound + window->master inbound window->master LAW->the ucode address in + master's memory space. Building the Software: ====================== diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile index 34f6c54698..33e93c88d7 100644 --- a/arch/powerpc/cpu/mpc85xx/Makefile +++ b/arch/powerpc/cpu/mpc85xx/Makefile @@ -55,8 +55,6 @@ COBJS-$(CONFIG_P1011) += ddr-gen3.o COBJS-$(CONFIG_P1012) += ddr-gen3.o COBJS-$(CONFIG_P1013) += ddr-gen3.o COBJS-$(CONFIG_P1014) += ddr-gen3.o -COBJS-$(CONFIG_P1015) += ddr-gen3.o -COBJS-$(CONFIG_P1016) += ddr-gen3.o COBJS-$(CONFIG_P1020) += ddr-gen3.o COBJS-$(CONFIG_P1021) += ddr-gen3.o COBJS-$(CONFIG_P1022) += ddr-gen3.o @@ -64,10 +62,8 @@ COBJS-$(CONFIG_P1024) += ddr-gen3.o COBJS-$(CONFIG_P1025) += ddr-gen3.o COBJS-$(CONFIG_P2010) += ddr-gen3.o COBJS-$(CONFIG_P2020) += ddr-gen3.o -COBJS-$(CONFIG_PPC_P2040) += ddr-gen3.o COBJS-$(CONFIG_PPC_P2041) += ddr-gen3.o COBJS-$(CONFIG_PPC_P3041) += ddr-gen3.o -COBJS-$(CONFIG_PPC_P3060) += ddr-gen3.o COBJS-$(CONFIG_PPC_P4080) += ddr-gen3.o COBJS-$(CONFIG_PPC_P5020) += ddr-gen3.o COBJS-$(CONFIG_BSC9131) += ddr-gen3.o @@ -80,10 +76,8 @@ COBJS-$(CONFIG_PCI) += pci.o COBJS-$(CONFIG_SYS_DPAA_QBMAN) += portals.o # various SoC specific assignments -COBJS-$(CONFIG_PPC_P2040) += p2041_ids.o COBJS-$(CONFIG_PPC_P2041) += p2041_ids.o COBJS-$(CONFIG_PPC_P3041) += p3041_ids.o -COBJS-$(CONFIG_PPC_P3060) += p3060_ids.o COBJS-$(CONFIG_PPC_P4080) += p4080_ids.o COBJS-$(CONFIG_PPC_P5020) += p5020_ids.o @@ -103,8 +97,6 @@ COBJS-$(CONFIG_P1011) += p1021_serdes.o COBJS-$(CONFIG_P1012) += p1021_serdes.o COBJS-$(CONFIG_P1013) += p1022_serdes.o COBJS-$(CONFIG_P1014) += p1010_serdes.o -COBJS-$(CONFIG_P1015) += p1021_serdes.o -COBJS-$(CONFIG_P1016) += p1021_serdes.o COBJS-$(CONFIG_P1017) += p1023_serdes.o COBJS-$(CONFIG_P1020) += p1021_serdes.o COBJS-$(CONFIG_P1021) += p1021_serdes.o @@ -114,10 +106,8 @@ COBJS-$(CONFIG_P1024) += p1021_serdes.o COBJS-$(CONFIG_P1025) += p1021_serdes.o COBJS-$(CONFIG_P2010) += p2020_serdes.o COBJS-$(CONFIG_P2020) += p2020_serdes.o -COBJS-$(CONFIG_PPC_P2040) += p2041_serdes.o COBJS-$(CONFIG_PPC_P2041) += p2041_serdes.o COBJS-$(CONFIG_PPC_P3041) += p3041_serdes.o -COBJS-$(CONFIG_PPC_P3060) += p3060_serdes.o COBJS-$(CONFIG_PPC_P4080) += p4080_serdes.o COBJS-$(CONFIG_PPC_P5020) += p5020_serdes.o diff --git a/arch/powerpc/cpu/mpc85xx/cmd_errata.c b/arch/powerpc/cpu/mpc85xx/cmd_errata.c index 4e1a54ad0c..e8989bdf45 100644 --- a/arch/powerpc/cpu/mpc85xx/cmd_errata.c +++ b/arch/powerpc/cpu/mpc85xx/cmd_errata.c @@ -27,6 +27,9 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { +#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011 + extern int enable_cpu_a011_workaround; +#endif __maybe_unused u32 svr = get_svr(); #if defined(CONFIG_FSL_SATA_V2) && defined(CONFIG_FSL_SATA_ERRATUM_A001) @@ -56,8 +59,9 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) /* * NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in 3.0 * also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1 + * The SVR has been checked by cpu_init_r(). */ - if (SVR_SOC_VER(svr) != SVR_P4080 || SVR_MAJ(svr) < 3) + if (enable_cpu_a011_workaround) puts("Work-around for Erratum CPU-A011 enabled\n"); #endif #if defined(CONFIG_SYS_FSL_ERRATUM_CPU_A003999) @@ -120,6 +124,9 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) if ((SVR_MAJ(svr) == 1) || IS_SVR_REV(svr, 2, 0)) puts("Work-around for Erratum NMG ETSEC129 enabled\n"); #endif +#ifdef CONFIG_SYS_FSL_ERRATUM_A004510 + puts("Work-around for Erratum A004510 enabled\n"); +#endif return 0; } diff --git a/arch/powerpc/cpu/mpc85xx/cpu.c b/arch/powerpc/cpu/mpc85xx/cpu.c index c1815e8860..5ddb29435c 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu.c +++ b/arch/powerpc/cpu/mpc85xx/cpu.c @@ -117,6 +117,9 @@ int checkcpu (void) case PVR_VER_E5500: puts("E5500"); break; + case PVR_VER_E6500: + puts("E6500"); + break; default: puts("Unknown"); break; @@ -427,11 +430,21 @@ static void dump_spd_ddr_reg(void) case 0: ddr[i] = (void *)CONFIG_SYS_MPC85xx_DDR_ADDR; break; -#ifdef CONFIG_SYS_MPC85xx_DDR2_ADDR +#if defined(CONFIG_SYS_MPC85xx_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1) case 1: ddr[i] = (void *)CONFIG_SYS_MPC85xx_DDR2_ADDR; break; #endif +#if defined(CONFIG_SYS_MPC85xx_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2) + case 2: + ddr[i] = (void *)CONFIG_SYS_MPC85xx_DDR3_ADDR; + break; +#endif +#if defined(CONFIG_SYS_MPC85xx_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3) + case 3: + ddr[i] = (void *)CONFIG_SYS_MPC85xx_DDR4_ADDR; + break; +#endif default: printf("%s unexpected controller number = %u\n", __func__, i); diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c index fc6c2877d2..afb56719da 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c @@ -38,6 +38,7 @@ #include <asm/fsl_law.h> #include <asm/fsl_serdes.h> #include <asm/fsl_srio.h> +#include <hwconfig.h> #include <linux/compiler.h> #include "mp.h" #ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND @@ -311,11 +312,41 @@ int cpu_init_r(void) #if defined(CONFIG_SYS_P4080_ERRATUM_CPU22) || \ defined(CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011) /* + * CPU22 and NMG_CPU_A011 share the same workaround. * CPU22 applies to P4080 rev 1.0, 2.0, fixed in 3.0 * NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in 3.0 - * also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1 + * also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1, both + * fixed in 2.0. NMG_CPU_A011 is activated by default and can + * be disabled by hwconfig with syntax: + * + * fsl_cpu_a011:disable */ - if (SVR_SOC_VER(svr) != SVR_P4080 || SVR_MAJ(svr) < 3) { + extern int enable_cpu_a011_workaround; +#ifdef CONFIG_SYS_P4080_ERRATUM_CPU22 + enable_cpu_a011_workaround = (SVR_MAJ(svr) < 3); +#else + char buffer[HWCONFIG_BUFFER_SIZE]; + char *buf = NULL; + int n, res; + + n = getenv_f("hwconfig", buffer, sizeof(buffer)); + if (n > 0) + buf = buffer; + + res = hwconfig_arg_cmp_f("fsl_cpu_a011", "disable", buf); + if (res > 0) + enable_cpu_a011_workaround = 0; + else { + if (n >= HWCONFIG_BUFFER_SIZE) { + printf("fsl_cpu_a011 was not found. hwconfig variable " + "may be too long\n"); + } + enable_cpu_a011_workaround = + (SVR_SOC_VER(svr) == SVR_P4080 && SVR_MAJ(svr) < 3) || + (SVR_SOC_VER(svr) != SVR_P4080 && SVR_MAJ(svr) < 2); + } +#endif + if (enable_cpu_a011_workaround) { flush_dcache(); mtspr(L1CSR2, (mfspr(L1CSR2) | L1CSR2_DCWS)); sync(); @@ -447,11 +478,18 @@ skip_l2: #ifdef CONFIG_SYS_SRIO srio_init(); -#ifdef CONFIG_SRIOBOOT_MASTER - srio_boot_master(); -#ifdef CONFIG_SRIOBOOT_SLAVE_HOLDOFF - srio_boot_master_release_slave(); -#endif +#ifdef CONFIG_FSL_CORENET + char *s = getenv("bootmaster"); + if (s) { + if (!strcmp(s, "SRIO1")) { + srio_boot_master(1); + srio_boot_master_release_slave(1); + } + if (!strcmp(s, "SRIO2")) { + srio_boot_master(2); + srio_boot_master_release_slave(2); + } + } #endif #endif diff --git a/arch/powerpc/cpu/mpc85xx/ddr-gen3.c b/arch/powerpc/cpu/mpc85xx/ddr-gen3.c index 81961def1b..ca4ed62645 100644 --- a/arch/powerpc/cpu/mpc85xx/ddr-gen3.c +++ b/arch/powerpc/cpu/mpc85xx/ddr-gen3.c @@ -1,5 +1,5 @@ /* - * Copyright 2008-2011 Freescale Semiconductor, Inc. + * Copyright 2008-2012 Freescale Semiconductor, Inc. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -32,9 +32,21 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, case 0: ddr = (void *)CONFIG_SYS_MPC85xx_DDR_ADDR; break; +#if defined(CONFIG_SYS_MPC85xx_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1) case 1: ddr = (void *)CONFIG_SYS_MPC85xx_DDR2_ADDR; break; +#endif +#if defined(CONFIG_SYS_MPC85xx_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2) + case 2: + ddr = (void *)CONFIG_SYS_MPC85xx_DDR3_ADDR; + break; +#endif +#if defined(CONFIG_SYS_MPC85xx_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3) + case 3: + ddr = (void *)CONFIG_SYS_MPC85xx_DDR4_ADDR; + break; +#endif default: printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num); return; @@ -43,6 +55,7 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, out_be32(&ddr->eor, regs->ddr_eor); #ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 + debug("Workaround for ERRATUM_DDR111_DDR134\n"); for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { cs_sa = (regs->cs[i].bnds >> 16) & 0xfff; cs_ea = regs->cs[i].bnds & 0xfff; @@ -115,8 +128,12 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, out_be32(&ddr->ddr_cdr2, regs->ddr_cdr2); out_be32(&ddr->err_disable, regs->err_disable); out_be32(&ddr->err_int_en, regs->err_int_en); - for (i = 0; i < 32; i++) - out_be32(&ddr->debug[i], regs->debug[i]); + for (i = 0; i < 32; i++) { + if (regs->debug[i]) { + debug("Write to debug_%d as %08x\n", i+1, regs->debug[i]); + out_be32(&ddr->debug[i], regs->debug[i]); + } + } #ifdef CONFIG_SYS_FSL_ERRATUM_DDR_A003474 out_be32(&ddr->debug[12], 0x00000015); @@ -128,6 +145,7 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, temp_sdram_cfg &= ~(SDRAM_CFG_MEM_EN); out_be32(&ddr->sdram_cfg, temp_sdram_cfg); #ifdef CONFIG_SYS_FSL_ERRATUM_DDR_A003 + debug("Workaround for ERRATUM_DDR_A003\n"); if (regs->ddr_sdram_rcw_2 & 0x00f00000) { out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2 & 0xf07fffff); out_be32(&ddr->debug[2], 0x00000400); @@ -209,6 +227,7 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, * This erratum does not affect DDR3 mode, only for DDR2 mode. */ #ifdef CONFIG_SYS_FSL_ERRATUM_DDR_115 + debug("Workaround for ERRATUM_DDR_115\n"); if ((((in_be32(&ddr->sdram_cfg) >> 24) & 0x7) == SDRAM_TYPE_DDR2) && in_be32(&ddr->sdram_cfg) & 0x80000) { /* set DEBUG_1[31] */ @@ -216,6 +235,7 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, } #endif #ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 + debug("Workaround for ERRATUM_DDR111_DDR134\n"); /* * This is the combined workaround for DDR111 and DDR134 * following the published errata for MPC8572 diff --git a/arch/powerpc/cpu/mpc85xx/fdt.c b/arch/powerpc/cpu/mpc85xx/fdt.c index 21c3ad49bf..a0a9b4c5ae 100644 --- a/arch/powerpc/cpu/mpc85xx/fdt.c +++ b/arch/powerpc/cpu/mpc85xx/fdt.c @@ -57,8 +57,9 @@ void ft_fixup_cpu(void *blob, u64 memory_limit) u32 *reg = (u32 *)fdt_getprop(blob, off, "reg", 0); if (reg) { - u64 val = *reg * SIZE_BOOT_ENTRY + spin_tbl_addr; - val = cpu_to_fdt32(val); + u32 phys_cpu_id = thread_to_core(*reg); + u64 val = phys_cpu_id * SIZE_BOOT_ENTRY + spin_tbl_addr; + val = cpu_to_fdt64(val); if (*reg == id) { fdt_setprop_string(blob, off, "status", "okay"); @@ -534,7 +535,7 @@ void fdt_fixup_fman_firmware(void *blob) #define fdt_fixup_fman_firmware(x) #endif -#if defined(CONFIG_PPC_P4080) || defined(CONFIG_PPC_P3060) +#if defined(CONFIG_PPC_P4080) static void fdt_fixup_usb(void *fdt) { ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); diff --git a/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c b/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c index 4b52dad56c..2a68060369 100644 --- a/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c +++ b/arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c @@ -46,8 +46,6 @@ static u32 serdes_prtcl_map; -#define HWCONFIG_BUFFER_SIZE 128 - #ifdef DEBUG static const char *serdes_prtcl_str[] = { [NONE] = "NA", @@ -68,6 +66,7 @@ static const char *serdes_prtcl_str[] = { [SGMII_FM2_DTSEC2] = "SGMII_FM2_DTSEC2", [SGMII_FM2_DTSEC3] = "SGMII_FM2_DTSEC3", [SGMII_FM2_DTSEC4] = "SGMII_FM2_DTSEC4", + [SGMII_FM2_DTSEC5] = "SGMII_FM2_DTSEC5", [XAUI_FM1] = "XAUI_FM1", [XAUI_FM2] = "XAUI_FM2", [AURORA] = "DEBUG", @@ -658,6 +657,7 @@ void fsl_serdes_init(void) case SGMII_FM2_DTSEC2: case SGMII_FM2_DTSEC3: case SGMII_FM2_DTSEC4: + case SGMII_FM2_DTSEC5: case XAUI_FM1: case XAUI_FM2: case SRIO1: @@ -717,6 +717,10 @@ void fsl_serdes_init(void) serdes8_devdisr2 |= FSL_CORENET_DEVDISR2_FM2 | FSL_CORENET_DEVDISR2_DTSEC2_4; break; + case SGMII_FM2_DTSEC5: + serdes8_devdisr2 |= FSL_CORENET_DEVDISR2_FM2 | + FSL_CORENET_DEVDISR2_DTSEC2_5; + break; case XAUI_FM1: serdes8_devdisr2 |= FSL_CORENET_DEVDISR2_FM1 | FSL_CORENET_DEVDISR2_10GEC1; diff --git a/arch/powerpc/cpu/mpc85xx/p3060_ids.c b/arch/powerpc/cpu/mpc85xx/p3060_ids.c deleted file mode 100644 index d32142f636..0000000000 --- a/arch/powerpc/cpu/mpc85xx/p3060_ids.c +++ /dev/null @@ -1,117 +0,0 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <common.h> -#include <asm/fsl_portals.h> -#include <asm/fsl_liodn.h> - -#ifdef CONFIG_SYS_DPAA_QBMAN -struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = { - /* dqrr liodn, frame data liodn, liodn off, sdest */ - SET_QP_INFO( 1, 2, 1, 0), - SET_QP_INFO( 3, 4, 2, 1), - SET_QP_INFO( 5, 6, 3, 2), - SET_QP_INFO( 7, 8, 4, 3), - SET_QP_INFO( 9, 10, 5, 4), - SET_QP_INFO(11, 12, 6, 5), - SET_QP_INFO(13, 14, 7, 6), - SET_QP_INFO(15, 16, 8, 7), - SET_QP_INFO(17, 18, 9, 0), /* for now sdest to 0 */ - SET_QP_INFO(19, 20, 10, 0), /* for now sdest to 0 */ -}; -#endif - -struct srio_liodn_id_table srio_liodn_tbl[] = { - SET_SRIO_LIODN_1(1, 198), - SET_SRIO_LIODN_1(2, 199), -}; -int srio_liodn_tbl_sz = ARRAY_SIZE(srio_liodn_tbl); - -struct liodn_id_table liodn_tbl[] = { - SET_USB_LIODN(1, "fsl-usb2-mph", 127), - SET_USB_LIODN(2, "fsl-usb2-dr", 157), - - SET_PCI_LIODN("fsl,qoriq-pcie-v2.2", 1, 193), - SET_PCI_LIODN("fsl,qoriq-pcie-v2.2", 2, 194), - - SET_DMA_LIODN(1, 196), - SET_DMA_LIODN(2, 197), - - SET_GUTS_LIODN("fsl,srio-rmu", 200, rmuliodnr, 0xd3000), - -#ifdef CONFIG_SYS_DPAA_QBMAN - SET_QMAN_LIODN(31), - SET_BMAN_LIODN(32), -#endif - SET_PME_LIODN(128), -}; -int liodn_tbl_sz = ARRAY_SIZE(liodn_tbl); - -#ifdef CONFIG_SYS_DPAA_FMAN -struct liodn_id_table fman1_liodn_tbl[] = { - SET_FMAN_RX_1G_LIODN(1, 0, 11), - SET_FMAN_RX_1G_LIODN(1, 1, 12), - SET_FMAN_RX_1G_LIODN(1, 2, 13), - SET_FMAN_RX_1G_LIODN(1, 3, 14), -}; -int fman1_liodn_tbl_sz = ARRAY_SIZE(fman1_liodn_tbl); - -#if (CONFIG_SYS_NUM_FMAN == 2) -struct liodn_id_table fman2_liodn_tbl[] = { - SET_FMAN_RX_1G_LIODN(2, 0, 16), - SET_FMAN_RX_1G_LIODN(2, 1, 17), - SET_FMAN_RX_1G_LIODN(2, 2, 18), - SET_FMAN_RX_1G_LIODN(2, 3, 19), -}; -int fman2_liodn_tbl_sz = ARRAY_SIZE(fman2_liodn_tbl); -#endif -#endif - -struct liodn_id_table sec_liodn_tbl[] = { - SET_SEC_JR_LIODN_ENTRY(0, 146, 154), - SET_SEC_JR_LIODN_ENTRY(1, 147, 155), - SET_SEC_JR_LIODN_ENTRY(2, 178, 186), - SET_SEC_JR_LIODN_ENTRY(3, 179, 187), - SET_SEC_RTIC_LIODN_ENTRY(a, 144), - SET_SEC_RTIC_LIODN_ENTRY(b, 145), - SET_SEC_RTIC_LIODN_ENTRY(c, 176), - SET_SEC_RTIC_LIODN_ENTRY(d, 177), - SET_SEC_DECO_LIODN_ENTRY(0, 129, 161), - SET_SEC_DECO_LIODN_ENTRY(1, 130, 162), - SET_SEC_DECO_LIODN_ENTRY(2, 131, 163), - SET_SEC_DECO_LIODN_ENTRY(3, 132, 164), - SET_SEC_DECO_LIODN_ENTRY(4, 133, 165), -}; -int sec_liodn_tbl_sz = ARRAY_SIZE(sec_liodn_tbl); - -struct liodn_id_table liodn_bases[] = { - [FSL_HW_PORTAL_SEC] = SET_LIODN_BASE_2(96, 106), -#ifdef CONFIG_SYS_DPAA_FMAN - [FSL_HW_PORTAL_FMAN1] = SET_LIODN_BASE_1(32), -#if (CONFIG_SYS_NUM_FMAN == 2) - [FSL_HW_PORTAL_FMAN2] = SET_LIODN_BASE_1(64), -#endif -#endif -#ifdef CONFIG_SYS_DPAA_PME - [FSL_HW_PORTAL_PME] = SET_LIODN_BASE_2(116, 133), -#endif -}; diff --git a/arch/powerpc/cpu/mpc85xx/p3060_serdes.c b/arch/powerpc/cpu/mpc85xx/p3060_serdes.c deleted file mode 100644 index e720dcf6bd..0000000000 --- a/arch/powerpc/cpu/mpc85xx/p3060_serdes.c +++ /dev/null @@ -1,118 +0,0 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <common.h> -#include <asm/io.h> -#include <asm/fsl_serdes.h> -#include <asm/processor.h> -#include <asm/io.h> -#include "fsl_corenet_serdes.h" - -static u8 serdes_cfg_tbl[][SRDS_MAX_LANES] = { - [0x03] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, PCIE2, PCIE2, - SGMII_FM2_DTSEC4, SGMII_FM1_DTSEC4, SGMII_FM2_DTSEC1, - SGMII_FM1_DTSEC1, SGMII_FM2_DTSEC2, SGMII_FM1_DTSEC2, - NONE, NONE, AURORA, AURORA}, - [0x06] = {PCIE1, PCIE1, PCIE1, PCIE1, NONE, NONE, SGMII_FM2_DTSEC3, - SGMII_FM1_DTSEC3, SGMII_FM2_DTSEC4, SGMII_FM1_DTSEC4, - SGMII_FM2_DTSEC1, SGMII_FM1_DTSEC1, SGMII_FM2_DTSEC2, - SGMII_FM1_DTSEC2, NONE, NONE, AURORA, AURORA}, - [0x16] = {SRIO2, SRIO2, SRIO2, SRIO2, SRIO1, SRIO1, SRIO1, SRIO1, - AURORA, AURORA, SGMII_FM2_DTSEC1, SGMII_FM1_DTSEC1, - SGMII_FM2_DTSEC2, SGMII_FM1_DTSEC2, SGMII_FM2_DTSEC3, - SGMII_FM1_DTSEC3, SGMII_FM2_DTSEC4, SGMII_FM1_DTSEC4}, - [0x19] = {SRIO2, SRIO2, SRIO2, SRIO2, SRIO1, SRIO1, SRIO1, SRIO1, - AURORA, AURORA, PCIE2, PCIE2, PCIE2, PCIE2, SGMII_FM2_DTSEC3, - SGMII_FM1_DTSEC3, SGMII_FM2_DTSEC4, SGMII_FM1_DTSEC4}, - [0x1c] = {NONE, NONE, SRIO1, SRIO2, NONE, NONE, NONE, NONE, - AURORA, AURORA, SGMII_FM2_DTSEC1, SGMII_FM1_DTSEC1, - SGMII_FM2_DTSEC2, SGMII_FM1_DTSEC2, SGMII_FM2_DTSEC3, - SGMII_FM1_DTSEC3, SGMII_FM2_DTSEC4, SGMII_FM1_DTSEC4}, -}; - -enum srds_prtcl serdes_get_prtcl(int cfg, int lane) -{ - if (!serdes_lane_enabled(lane)) - return NONE; - - return serdes_cfg_tbl[cfg][lane]; -} - -int is_serdes_prtcl_valid(u32 prtcl) -{ - int i; - - if (prtcl > ARRAY_SIZE(serdes_cfg_tbl)) - return 0; - - for (i = 0; i < SRDS_MAX_LANES; i++) { - if (serdes_cfg_tbl[prtcl][i] != NONE) - return 1; - } - - return 0; -} - -void soc_serdes_init(void) -{ - /* - * On the P3060 the devdisr2 register does not correctly reflect - * the state of the MACs based on the RCW fields. So disable the MACs - * based on the srds_prtcl and ec1, ec2, ec3 fields - */ - - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 devdisr2 = in_be32(&gur->devdisr2); - u32 rcwsr11 = in_be32(&gur->rcwsr[11]); - - /* NOTE: Leave FM1-1,FM1-2 alone for MDIO access */ - - if (!is_serdes_configured(SGMII_FM1_DTSEC3)) - devdisr2 |= FSL_CORENET_DEVDISR2_DTSEC1_3; - - if (!is_serdes_configured(SGMII_FM1_DTSEC4)) - devdisr2 |= FSL_CORENET_DEVDISR2_DTSEC1_4; - - if (!is_serdes_configured(SGMII_FM2_DTSEC1)) - devdisr2 |= FSL_CORENET_DEVDISR2_DTSEC2_1; - - if (!is_serdes_configured(SGMII_FM2_DTSEC2)) - devdisr2 |= FSL_CORENET_DEVDISR2_DTSEC2_2; - - if (!is_serdes_configured(SGMII_FM2_DTSEC3)) - devdisr2 |= FSL_CORENET_DEVDISR2_DTSEC2_3; - - if (!is_serdes_configured(SGMII_FM2_DTSEC4)) - devdisr2 |= FSL_CORENET_DEVDISR2_DTSEC2_4; - - if ((rcwsr11 & FSL_CORENET_RCWSR11_EC2) == - FSL_CORENET_RCWSR11_EC2_FM1_DTSEC2) { - devdisr2 &= ~FSL_CORENET_DEVDISR2_DTSEC1_2; - } - - if ((rcwsr11 & FSL_CORENET_RCWSR11_EC2) == - FSL_CORENET_RCWSR11_EC2_FM2_DTSEC1) { - devdisr2 &= ~FSL_CORENET_DEVDISR2_DTSEC2_1; - } - - out_be32(&gur->devdisr2, devdisr2); -} diff --git a/arch/powerpc/cpu/mpc85xx/release.S b/arch/powerpc/cpu/mpc85xx/release.S index 1860684c11..22e73e0661 100644 --- a/arch/powerpc/cpu/mpc85xx/release.S +++ b/arch/powerpc/cpu/mpc85xx/release.S @@ -1,5 +1,5 @@ /* - * Copyright 2008-2011 Freescale Semiconductor, Inc. + * Copyright 2008-2012 Freescale Semiconductor, Inc. * Kumar Gala <kumar.gala@freescale.com> * * See file CREDITS for list of people who contributed to this @@ -74,6 +74,33 @@ __secondary_start_page: mtspr 977,r3 #endif +#ifdef CONFIG_SYS_FSL_ERRATUM_A004510 + mfspr r3,SPRN_SVR + rlwinm r3,r3,0,0xff + li r4,CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV + cmpw r3,r4 + beq 1f + +#ifdef CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 + li r4,CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 + cmpw r3,r4 + beq 1f +#endif + + /* Not a supported revision affected by erratum */ + b 2f + +1: /* Erratum says set bits 55:60 to 001001 */ + msync + isync + mfspr r3,976 + li r4,0x48 + rlwimi r3,r4,0,0x1f8 + mtspr 976,r3 + isync +2: +#endif + /* Enable branch prediction */ lis r3,BUCSR_ENABLE@h ori r3,r3,BUCSR_ENABLE@l @@ -128,7 +155,27 @@ __secondary_start_page: /* r10 has the base address for the entry */ mfspr r0,SPRN_PIR -#ifdef CONFIG_E500MC +#if defined(CONFIG_E6500) +/* + * PIR definition for E6500 + * 0-17 Reserved (logic 0s) + * 8-19 CHIP_ID, 2’b00 - SoC 1 + * all others - reserved + * 20-24 CLUSTER_ID 5’b00000 - CCM 1 + * all others - reserved + * 25-26 CORE_CLUSTER_ID 2’b00 - cluster 1 + * 2’b01 - cluster 2 + * 2’b10 - cluster 3 + * 2’b11 - cluster 4 + * 27-28 CORE_ID 2’b00 - core 0 + * 2’b01 - core 1 + * 2’b10 - core 2 + * 2’b11 - core 3 + * 29-31 THREAD_ID 3’b000 - thread 0 + * 3’b001 - thread 1 + */ + rlwinm r4,r0,29,25,31 +#elif defined(CONFIG_E500MC) rlwinm r4,r0,27,27,31 #else mr r4,r0 @@ -143,6 +190,25 @@ __secondary_start_page: mtspr L1CSR2,r8 #endif +#ifdef CONFIG_E6500 + mfspr r0,SPRN_PIR + /* + * core 0 thread 0: pir reset value 0x00, new pir 0 + * core 0 thread 1: pir reset value 0x01, new pir 1 + * core 1 thread 0: pir reset value 0x08, new pir 2 + * core 1 thread 1: pir reset value 0x09, new pir 3 + * core 2 thread 0: pir reset value 0x10, new pir 4 + * core 2 thread 1: pir reset value 0x11, new pir 5 + * etc. + * + * Only thread 0 of each core will be running, updating PIR doesn't + * need to deal with the thread bits. + */ + rlwinm r4,r0,30,24,30 +#endif + + mtspr SPRN_PIR,r4 /* write to PIR register */ + #if defined(CONFIG_SYS_P4080_ERRATUM_CPU22) || \ defined(CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011) /* @@ -163,6 +229,12 @@ __secondary_start_page: cmpw r3,r5 bge 2f 1: +#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011 + lis r3,toreset(enable_cpu_a011_workaround)@ha + lwz r3,toreset(enable_cpu_a011_workaround)@l(r3) + cmpwi r3,0 + beq 2f +#endif mfspr r3,L1CSR2 oris r3,r3,(L1CSR2_DCWS)@h mtspr L1CSR2,r3 @@ -220,7 +292,7 @@ __secondary_start_page: /* setup the entry */ li r3,0 li r8,1 - stw r0,ENTRY_PIR(r10) + stw r4,ENTRY_PIR(r10) stw r3,ENTRY_ADDR_UPPER(r10) stw r8,ENTRY_ADDR_LOWER(r10) stw r3,ENTRY_R3_UPPER(r10) @@ -346,6 +418,15 @@ __bootpg_addr: __spin_table: .space CONFIG_MAX_CPUS*ENTRY_SIZE + /* + * This variable is set by cpu_init_r() after parsing hwconfig + * to enable workaround for erratum NMG_CPU_A011. + */ + .align L1_CACHE_SHIFT + .global enable_cpu_a011_workaround +enable_cpu_a011_workaround: + .long 1 + /* Fill in the empty space. The actual reset vector is * the last word of the page */ __secondary_start_code_end: diff --git a/arch/powerpc/cpu/mpc85xx/speed.c b/arch/powerpc/cpu/mpc85xx/speed.c index ce47532455..abfeb268d4 100644 --- a/arch/powerpc/cpu/mpc85xx/speed.c +++ b/arch/powerpc/cpu/mpc85xx/speed.c @@ -186,8 +186,7 @@ void get_sys_info (sys_info_t * sysInfo) #endif #ifdef CONFIG_QE -#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ - defined(CONFIG_P1021) || defined(CONFIG_P1025) +#if defined(CONFIG_P1012) || defined(CONFIG_P1021) || defined(CONFIG_P1025) sysInfo->freqQE = sysInfo->freqSystemBus; #else qe_ratio = ((gur->porpllsr) & MPC85xx_PORPLLSR_QE_RATIO) diff --git a/arch/powerpc/cpu/mpc85xx/start.S b/arch/powerpc/cpu/mpc85xx/start.S index 6aabc30c28..9e04257d2c 100644 --- a/arch/powerpc/cpu/mpc85xx/start.S +++ b/arch/powerpc/cpu/mpc85xx/start.S @@ -86,6 +86,35 @@ _start_e500: li r1,MSR_DE mtmsr r1 +#ifdef CONFIG_SYS_FSL_ERRATUM_A004510 + mfspr r3,SPRN_SVR + rlwinm r3,r3,0,0xff + li r4,CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV + cmpw r3,r4 + beq 1f + +#ifdef CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 + li r4,CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 + cmpw r3,r4 + beq 1f +#endif + + /* Not a supported revision affected by erratum */ + li r27,0 + b 2f + +1: li r27,1 /* Remember for later that we have the erratum */ + /* Erratum says set bits 55:60 to 001001 */ + msync + isync + mfspr r3,976 + li r4,0x48 + rlwimi r3,r4,0,0x1f8 + mtspr 976,r3 + isync +2: +#endif + #if defined(CONFIG_SECURE_BOOT) && defined(CONFIG_E500MC) /* ISBC uses L2 as stack. * Disable L2 cache here so that u-boot can enable it later @@ -406,12 +435,11 @@ l2_disabled: * Search for the TLB that covers the code we're executing, and shrink it * so that it covers only this 4K page. That will ensure that any other * TLB we create won't interfere with it. We assume that the TLB exists, - * which is why we don't check the Valid bit of MAS1. + * which is why we don't check the Valid bit of MAS1. We also assume + * it is in TLB1. * * This is necessary, for example, when booting from the on-chip ROM, * which (oddly) creates a single 4GB TLB that covers CCSR and DDR. - * If we don't shrink this TLB now, then we'll accidentally delete it - * in "purge_old_ccsr_tlb" below. */ bl nexti /* Find our address */ nexti: mflr r1 /* R1 = our PC */ @@ -421,11 +449,15 @@ nexti: mflr r1 /* R1 = our PC */ msync tlbsx 0, r1 /* This must succeed */ + mfspr r14, MAS0 /* Save ESEL for later */ + rlwinm r14, r14, 16, 0xfff + /* Set the size of the TLB to 4KB */ mfspr r3, MAS1 li r2, 0xF00 andc r3, r3, r2 /* Clear the TSIZE bits */ ori r3, r3, MAS1_TSIZE(BOOKE_PAGESZ_4K)@l + oris r3, r3, MAS1_IPROT@h mtspr MAS1, r3 /* @@ -440,6 +472,14 @@ nexti: mflr r1 /* R1 = our PC */ mfspr r2, MAS2 andc r2, r2, r3 or r2, r2, r1 +#ifdef CONFIG_SYS_FSL_ERRATUM_A004510 + cmpwi r27,0 + beq 1f + andi. r15, r2, MAS2_I|MAS2_G /* save the old I/G for later */ + rlwinm r2, r2, 0, ~MAS2_I + ori r2, r2, MAS2_G +1: +#endif mtspr MAS2, r2 /* Set the EPN to our PC base address */ mfspr r2, MAS3 @@ -452,6 +492,39 @@ nexti: mflr r1 /* R1 = our PC */ tlbwe /* + * Clear out any other TLB entries that may exist, to avoid conflicts. + * Our TLB entry is in r14. + */ + li r0, TLBIVAX_ALL | TLBIVAX_TLB0 + tlbivax 0, r0 + tlbsync + + mfspr r4, SPRN_TLB1CFG + rlwinm r4, r4, 0, TLBnCFG_NENTRY_MASK + + li r3, 0 + mtspr MAS1, r3 +1: cmpw r3, r14 +#if defined(CONFIG_SYS_PPC_E500_DEBUG_TLB) && !defined(CONFIG_NAND_SPL) + cmpwi cr1, r3, CONFIG_SYS_PPC_E500_DEBUG_TLB + cror cr0*4+eq, cr0*4+eq, cr1*4+eq +#endif + rlwinm r5, r3, 16, MAS0_ESEL_MSK + addi r3, r3, 1 + beq 2f /* skip the entry we're executing from */ + + oris r5, r5, MAS0_TLBSEL(1)@h + mtspr MAS0, r5 + + isync + tlbwe + isync + msync + +2: cmpw r3, r4 + blt 1b + +/* * Relocate CCSR, if necessary. We relocate CCSR if (obviously) the default * location is not where we want it. This typically happens on a 36-bit * system, where we want to move CCSR to near the top of 36-bit address space. @@ -469,41 +542,15 @@ nexti: mflr r1 /* R1 = our PC */ #error "CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW) must be defined." #endif -purge_old_ccsr_tlb: - lis r8, CONFIG_SYS_CCSRBAR@h - ori r8, r8, CONFIG_SYS_CCSRBAR@l - lis r9, (CONFIG_SYS_CCSRBAR + 0x1000)@h - ori r9, r9, (CONFIG_SYS_CCSRBAR + 0x1000)@l - - /* - * In a multi-stage boot (e.g. NAND boot), a previous stage may have - * created a TLB for CCSR, which will interfere with our relocation - * code. Since we're going to create a new TLB for CCSR anyway, - * it should be safe to delete this old TLB here. We have to search - * for it, though. - */ - - li r1, 0 - mtspr MAS6, r1 /* Search the current address space and PID */ - isync - msync - tlbsx 0, r8 - mfspr r1, MAS1 - andis. r2, r1, MAS1_VALID@h /* Check for the Valid bit */ - beq 1f /* Skip if no TLB found */ - - rlwinm r1, r1, 0, 1, 31 /* Clear Valid bit */ - mtspr MAS1, r1 - isync - msync - tlbwe -1: - create_ccsr_new_tlb: /* * Create a TLB for the new location of CCSR. Register R8 is reserved * for the virtual address of this TLB (CONFIG_SYS_CCSRBAR). */ + lis r8, CONFIG_SYS_CCSRBAR@h + ori r8, r8, CONFIG_SYS_CCSRBAR@l + lis r9, (CONFIG_SYS_CCSRBAR + 0x1000)@h + ori r9, r9, (CONFIG_SYS_CCSRBAR + 0x1000)@l lis r0, FSL_BOOKE_MAS0(0, 0, 0)@h ori r0, r0, FSL_BOOKE_MAS0(0, 0, 0)@l lis r1, FSL_BOOKE_MAS1(1, 0, 0, 0, BOOKE_PAGESZ_4K)@h @@ -719,6 +766,253 @@ delete_temp_tlbs: tlbwe #endif /* #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR_PHYS) */ +#ifdef CONFIG_SYS_FSL_ERRATUM_A004510 +#define DCSR_LAWBARH0 (CONFIG_SYS_CCSRBAR + 0x1000) +#define LAW_SIZE_1M 0x13 +#define DCSRBAR_LAWAR (LAW_EN | (0x1d << 20) | LAW_SIZE_1M) + + cmpwi r27,0 + beq 9f + + /* + * Create a TLB entry for CCSR + * + * We're executing out of TLB1 entry in r14, and that's the only + * TLB entry that exists. To allocate some TLB entries for our + * own use, flip a bit high enough that we won't flip it again + * via incrementing. + */ + + xori r8, r14, 32 + lis r0, MAS0_TLBSEL(1)@h + rlwimi r0, r8, 16, MAS0_ESEL_MSK + lis r1, FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)@h + ori r1, r1, FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)@l + lis r7, CONFIG_SYS_CCSRBAR@h + ori r7, r7, CONFIG_SYS_CCSRBAR@l + ori r2, r7, MAS2_I|MAS2_G + lis r3, FSL_BOOKE_MAS3(CONFIG_SYS_CCSRBAR_PHYS_LOW, 0, (MAS3_SW|MAS3_SR))@h + ori r3, r3, FSL_BOOKE_MAS3(CONFIG_SYS_CCSRBAR_PHYS_LOW, 0, (MAS3_SW|MAS3_SR))@l + lis r4, CONFIG_SYS_CCSRBAR_PHYS_HIGH@h + ori r4, r4, CONFIG_SYS_CCSRBAR_PHYS_HIGH@l + mtspr MAS0, r0 + mtspr MAS1, r1 + mtspr MAS2, r2 + mtspr MAS3, r3 + mtspr MAS7, r4 + isync + tlbwe + isync + msync + + /* Map DCSR temporarily to physical address zero */ + li r0, 0 + lis r3, DCSRBAR_LAWAR@h + ori r3, r3, DCSRBAR_LAWAR@l + + stw r0, 0xc00(r7) /* LAWBARH0 */ + stw r0, 0xc04(r7) /* LAWBARL0 */ + sync + stw r3, 0xc08(r7) /* LAWAR0 */ + + /* Read back from LAWAR to ensure the update is complete. */ + lwz r3, 0xc08(r7) /* LAWAR0 */ + isync + + /* Create a TLB entry for DCSR at zero */ + + addi r9, r8, 1 + lis r0, MAS0_TLBSEL(1)@h + rlwimi r0, r9, 16, MAS0_ESEL_MSK + lis r1, FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)@h + ori r1, r1, FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)@l + li r6, 0 /* DCSR effective address */ + ori r2, r6, MAS2_I|MAS2_G + li r3, MAS3_SW|MAS3_SR + li r4, 0 + mtspr MAS0, r0 + mtspr MAS1, r1 + mtspr MAS2, r2 + mtspr MAS3, r3 + mtspr MAS7, r4 + isync + tlbwe + isync + msync + + /* enable the timebase */ +#define CTBENR 0xe2084 + li r3, 1 + addis r4, r7, CTBENR@ha + stw r3, CTBENR@l(r4) + lwz r3, CTBENR@l(r4) + twi 0,r3,0 + isync + + .macro erratum_set_ccsr offset value + addis r3, r7, \offset@ha + lis r4, \value@h + addi r3, r3, \offset@l + ori r4, r4, \value@l + bl erratum_set_value + .endm + + .macro erratum_set_dcsr offset value + addis r3, r6, \offset@ha + lis r4, \value@h + addi r3, r3, \offset@l + ori r4, r4, \value@l + bl erratum_set_value + .endm + + erratum_set_dcsr 0xb0e08 0xe0201800 + erratum_set_dcsr 0xb0e18 0xe0201800 + erratum_set_dcsr 0xb0e38 0xe0400000 + erratum_set_dcsr 0xb0008 0x00900000 + erratum_set_dcsr 0xb0e40 0xe00a0000 + erratum_set_ccsr 0x18600 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY + erratum_set_ccsr 0x10f00 0x415e5000 + erratum_set_ccsr 0x11f00 0x415e5000 + + /* Make temp mapping uncacheable again, if it was initially */ + bl 2f +2: mflr r3 + tlbsx 0, r3 + mfspr r4, MAS2 + rlwimi r4, r15, 0, MAS2_I + rlwimi r4, r15, 0, MAS2_G + mtspr MAS2, r4 + isync + tlbwe + isync + msync + + /* Clear the cache */ + lis r3,(L1CSR1_ICFI|L1CSR1_ICLFR)@h + ori r3,r3,(L1CSR1_ICFI|L1CSR1_ICLFR)@l + sync + isync + mtspr SPRN_L1CSR1,r3 + isync +2: sync + mfspr r4,SPRN_L1CSR1 + and. r4,r4,r3 + bne 2b + + lis r3,(L1CSR1_CPE|L1CSR1_ICE)@h + ori r3,r3,(L1CSR1_CPE|L1CSR1_ICE)@l + sync + isync + mtspr SPRN_L1CSR1,r3 + isync +2: sync + mfspr r4,SPRN_L1CSR1 + and. r4,r4,r3 + beq 2b + + /* Remove temporary mappings */ + lis r0, MAS0_TLBSEL(1)@h + rlwimi r0, r9, 16, MAS0_ESEL_MSK + li r3, 0 + mtspr MAS0, r0 + mtspr MAS1, r3 + isync + tlbwe + isync + msync + + li r3, 0 + stw r3, 0xc08(r7) /* LAWAR0 */ + lwz r3, 0xc08(r7) + isync + + lis r0, MAS0_TLBSEL(1)@h + rlwimi r0, r8, 16, MAS0_ESEL_MSK + li r3, 0 + mtspr MAS0, r0 + mtspr MAS1, r3 + isync + tlbwe + isync + msync + + b 9f + + /* r3 = addr, r4 = value, clobbers r5, r11, r12 */ +erratum_set_value: + /* Lock two cache lines into I-Cache */ + sync + mfspr r11, SPRN_L1CSR1 + rlwinm r11, r11, 0, ~L1CSR1_ICUL + sync + isync + mtspr SPRN_L1CSR1, r11 + isync + + mflr r12 + bl 5f +5: mflr r5 + addi r5, r5, 2f - 5b + icbtls 0, 0, r5 + addi r5, r5, 64 + + sync + mfspr r11, SPRN_L1CSR1 +3: andi. r11, r11, L1CSR1_ICUL + bne 3b + + icbtls 0, 0, r5 + addi r5, r5, 64 + + sync + mfspr r11, SPRN_L1CSR1 +3: andi. r11, r11, L1CSR1_ICUL + bne 3b + + b 2f + .align 6 + /* Inside a locked cacheline, wait a while, write, then wait a while */ +2: sync + + mfspr r5, SPRN_TBRL + addis r11, r5, 0x10000@h /* wait 65536 timebase ticks */ +4: mfspr r5, SPRN_TBRL + subf. r5, r5, r11 + bgt 4b + + stw r4, 0(r3) + + mfspr r5, SPRN_TBRL + addis r11, r5, 0x10000@h /* wait 65536 timebase ticks */ +4: mfspr r5, SPRN_TBRL + subf. r5, r5, r11 + bgt 4b + + sync + + /* + * Fill out the rest of this cache line and the next with nops, + * to ensure that nothing outside the locked area will be + * fetched due to a branch. + */ + .rept 19 + nop + .endr + + sync + mfspr r11, SPRN_L1CSR1 + rlwinm r11, r11, 0, ~L1CSR1_ICUL + sync + isync + mtspr SPRN_L1CSR1, r11 + isync + + mtlr r12 + blr + +9: +#endif + create_init_ram_area: lis r6,FSL_BOOKE_MAS0(1, 15, 0)@h ori r6,r6,FSL_BOOKE_MAS0(1, 15, 0)@l @@ -855,18 +1149,12 @@ version_string: .globl _start_cont _start_cont: /* Setup the stack in initial RAM,could be L2-as-SRAM or L1 dcache*/ - lis r1,CONFIG_SYS_INIT_RAM_ADDR@h - ori r1,r1,CONFIG_SYS_INIT_SP_OFFSET@l - + lis r3,(CONFIG_SYS_INIT_RAM_ADDR)@h + ori r3,r3,((CONFIG_SYS_INIT_SP_OFFSET-16)&~0xf)@l /* Align to 16 */ li r0,0 - stwu r0,-4(r1) - stwu r0,-4(r1) /* Terminate call chain */ - - stwu r1,-8(r1) /* Save back chain and move SP */ - lis r0,RESET_VECTOR@h /* Address of reset vector */ - ori r0,r0,RESET_VECTOR@l - stwu r1,-8(r1) /* Save back chain and move SP */ - stw r0,+12(r1) /* Save return addr (underflow vect) */ + stw r0,0(r3) /* Terminate Back Chain */ + stw r0,+4(r3) /* NULL return address. */ + mr r1,r3 /* Transfer to SP(r1) */ GET_GOT bl cpu_init_early_f diff --git a/arch/powerpc/cpu/mpc8xxx/cpu.c b/arch/powerpc/cpu/mpc8xxx/cpu.c index cbc674211a..78a8f926b3 100644 --- a/arch/powerpc/cpu/mpc8xxx/cpu.c +++ b/arch/powerpc/cpu/mpc8xxx/cpu.c @@ -57,8 +57,6 @@ struct cpu_type cpu_type_list [] = { CPU_TYPE_ENTRY(P1012, P1012, 1), CPU_TYPE_ENTRY(P1013, P1013, 1), CPU_TYPE_ENTRY(P1014, P1014, 1), - CPU_TYPE_ENTRY(P1015, P1015, 1), - CPU_TYPE_ENTRY(P1016, P1016, 1), CPU_TYPE_ENTRY(P1017, P1017, 1), CPU_TYPE_ENTRY(P1020, P1020, 2), CPU_TYPE_ENTRY(P1021, P1021, 2), @@ -71,7 +69,6 @@ struct cpu_type cpu_type_list [] = { CPU_TYPE_ENTRY(P2040, P2040, 4), CPU_TYPE_ENTRY(P2041, P2041, 4), CPU_TYPE_ENTRY(P3041, P3041, 4), - CPU_TYPE_ENTRY_MASK(P3060, P3060, 6, 0xf3), CPU_TYPE_ENTRY(P4040, P4040, 4), CPU_TYPE_ENTRY(P4080, P4080, 8), CPU_TYPE_ENTRY(P5010, P5010, 1), @@ -85,7 +82,39 @@ struct cpu_type cpu_type_list [] = { #endif }; -struct cpu_type cpu_type_unknown = CPU_TYPE_ENTRY(Unknown, Unknown, 1); +#ifdef CONFIG_SYS_FSL_QORIQ_CHASSIS2 +u32 compute_ppc_cpumask(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + int i = 0, count = 0; + u32 cluster, mask = 0; + + do { + int j; + cluster = in_be32(&gur->tp_cluster[i++].lower); + for (j = 0; j < 4; j++) { + u32 idx = (cluster >> (j*8)) & TP_CLUSTER_INIT_MASK; + u32 type = in_be32(&gur->tp_ityp[idx]); + + if (type & TP_ITYP_AV) { + if (TP_ITYP_TYPE(type) == TP_ITYP_TYPE_PPC) + mask |= 1 << count; + } + count++; + } + } while ((cluster & TP_CLUSTER_EOC) != TP_CLUSTER_EOC); + + return mask; +} +#else /* CONFIG_SYS_FSL_QORIQ_CHASSIS2 */ +/* + * Before chassis genenration 2, the cpumask should be hard-coded. + * In case of cpu type unknown or cpumask unset, use 1 as fail save. + */ +#define compute_ppc_cpumask() 1 +#endif /* CONFIG_SYS_FSL_QORIQ_CHASSIS2 */ + +struct cpu_type cpu_type_unknown = CPU_TYPE_ENTRY(Unknown, Unknown, 0); struct cpu_type *identify_cpu(u32 ver) { @@ -113,6 +142,9 @@ u32 cpu_mask() return ((in_be32(&pic->frr) & MPC8xxx_PICFRR_NCPU_MASK) >> MPC8xxx_PICFRR_NCPU_SHIFT) + 1; + if (cpu->num_cores == 0) + return compute_ppc_cpumask(); + return cpu->mask; } @@ -120,13 +152,14 @@ u32 cpu_mask() * Return the number of cores on this SOC. */ int cpu_numcores() { - ccsr_pic_t __iomem *pic = (void *)CONFIG_SYS_MPC8xxx_PIC_ADDR; struct cpu_type *cpu = gd->cpu; - /* better to query feature reporting register than just assume 1 */ - if (cpu == &cpu_type_unknown) - return ((in_be32(&pic->frr) & MPC8xxx_PICFRR_NCPU_MASK) >> - MPC8xxx_PICFRR_NCPU_SHIFT) + 1; + /* + * Report # of cores in terms of the cpu_mask if we haven't + * figured out how many there are yet + */ + if (cpu->num_cores == 0) + return hweight32(cpu_mask()); return cpu->num_cores; } @@ -138,9 +171,7 @@ int cpu_numcores() { */ int is_core_valid(unsigned int core) { - struct cpu_type *cpu = gd->cpu; - - return !!((1 << core) & cpu->mask); + return !!((1 << core) & cpu_mask()); } int probecpu (void) @@ -156,6 +187,19 @@ int probecpu (void) return 0; } +/* Once in memory, compute mask & # cores once and save them off */ +int fixup_cpu(void) +{ + struct cpu_type *cpu = gd->cpu; + + if (cpu->num_cores == 0) { + cpu->mask = cpu_mask(); + cpu->num_cores = cpu_numcores(); + } + + return 0; +} + /* * Initializes on-chip ethernet controllers. * to override, implement board_eth_init() diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c b/arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c index 2067d53ad2..2592873c9f 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c @@ -1,5 +1,5 @@ /* - * Copyright 2008-2011 Freescale Semiconductor, Inc. + * Copyright 2008-2012 Freescale Semiconductor, Inc. * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the Free @@ -151,8 +151,19 @@ static void set_csn_config(int dimm_number, int i, fsl_ddr_cfg_regs_t *ddr, if (dimm_params[dimm_number].n_ranks > 0) { go_config = 1; /* These fields only available in CS0_CONFIG */ - intlv_en = popts->memctl_interleaving; - intlv_ctl = popts->memctl_interleaving_mode; + if (!popts->memctl_interleaving) + break; + switch (popts->memctl_interleaving_mode) { + case FSL_DDR_CACHE_LINE_INTERLEAVING: + case FSL_DDR_PAGE_INTERLEAVING: + case FSL_DDR_BANK_INTERLEAVING: + case FSL_DDR_SUPERBANK_INTERLEAVING: + intlv_en = popts->memctl_interleaving; + intlv_ctl = popts->memctl_interleaving_mode; + break; + default: + break; + } } break; case 1: @@ -302,29 +313,41 @@ static void set_timing_cfg_0(fsl_ddr_cfg_regs_t *ddr, /* DDR SDRAM Timing Configuration 3 (TIMING_CFG_3) */ static void set_timing_cfg_3(fsl_ddr_cfg_regs_t *ddr, + const memctl_options_t *popts, const common_timing_params_t *common_dimm, unsigned int cas_latency) { + /* Extended precharge to activate interval (tRP) */ + unsigned int ext_pretoact = 0; /* Extended Activate to precharge interval (tRAS) */ unsigned int ext_acttopre = 0; - unsigned int ext_refrec; /* Extended refresh recovery time (tRFC) */ - unsigned int ext_caslat = 0; /* Extended MCAS latency from READ cmd */ - unsigned int cntl_adj = 0; /* Control Adjust */ - - /* If the tRAS > 19 MCLK, we use the ext mode */ - if (picos_to_mclk(common_dimm->tRAS_ps) > 0x13) - ext_acttopre = 1; - + /* Extended activate to read/write interval (tRCD) */ + unsigned int ext_acttorw = 0; + /* Extended refresh recovery time (tRFC) */ + unsigned int ext_refrec; + /* Extended MCAS latency from READ cmd */ + unsigned int ext_caslat = 0; + /* Extended last data to precharge interval (tWR) */ + unsigned int ext_wrrec = 0; + /* Control Adjust */ + unsigned int cntl_adj = 0; + + ext_pretoact = picos_to_mclk(common_dimm->tRP_ps) >> 4; + ext_acttopre = picos_to_mclk(common_dimm->tRAS_ps) >> 4; + ext_acttorw = picos_to_mclk(common_dimm->tRCD_ps) >> 4; + ext_caslat = (2 * cas_latency - 1) >> 4; ext_refrec = (picos_to_mclk(common_dimm->tRFC_ps) - 8) >> 4; - - /* If the CAS latency more than 8, use the ext mode */ - if (cas_latency > 8) - ext_caslat = 1; + /* ext_wrrec only deals with 16 clock and above, or 14 with OTF */ + ext_wrrec = (picos_to_mclk(common_dimm->tWR_ps) + + (popts->OTF_burst_chop_en ? 2 : 0)) >> 4; ddr->timing_cfg_3 = (0 - | ((ext_acttopre & 0x1) << 24) - | ((ext_refrec & 0xF) << 16) - | ((ext_caslat & 0x1) << 12) + | ((ext_pretoact & 0x1) << 28) + | ((ext_acttopre & 0x2) << 24) + | ((ext_acttorw & 0x1) << 22) + | ((ext_refrec & 0x1F) << 16) + | ((ext_caslat & 0x3) << 12) + | ((ext_wrrec & 0x1) << 8) | ((cntl_adj & 0x7) << 0) ); debug("FSLDDR: timing_cfg_3 = 0x%08x\n", ddr->timing_cfg_3); @@ -386,15 +409,16 @@ static void set_timing_cfg_1(fsl_ddr_cfg_regs_t *ddr, * we need set extend bit for it at * TIMING_CFG_3[EXT_CASLAT] */ - if (cas_latency > 8) - cas_latency -= 8; caslat_ctrl = 2 * cas_latency - 1; #endif refrec_ctrl = picos_to_mclk(common_dimm->tRFC_ps) - 8; wrrec_mclk = picos_to_mclk(common_dimm->tWR_ps); - wrrec_mclk = wrrec_table[wrrec_mclk - 1]; + if (wrrec_mclk > 16) + printf("Error: WRREC doesn't support more than 16 clocks\n"); + else + wrrec_mclk = wrrec_table[wrrec_mclk - 1]; if (popts->OTF_burst_chop_en) wrrec_mclk += 2; @@ -825,7 +849,7 @@ static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr, /* Mode Register - MR0 */ unsigned int dll_on; /* DLL control for precharge PD, 0=off, 1=on */ - unsigned int wr; /* Write Recovery */ + unsigned int wr = 0; /* Write Recovery */ unsigned int dll_rst; /* DLL Reset */ unsigned int mode; /* Normal=0 or Test=1 */ unsigned int caslat = 4;/* CAS# latency, default set as 6 cycles */ @@ -885,24 +909,37 @@ static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr, dll_on = 1; wr_mclk = (common_dimm->tWR_ps + mclk_ps - 1) / mclk_ps; - wr = wr_table[wr_mclk - 5]; + if (wr_mclk <= 16) { + wr = wr_table[wr_mclk - 5]; + } else { + printf("Error: unsupported write recovery for mode register " + "wr_mclk = %d\n", wr_mclk); + } dll_rst = 0; /* dll no reset */ mode = 0; /* normal mode */ /* look up table to get the cas latency bits */ - if (cas_latency >= 5 && cas_latency <= 11) { - unsigned char cas_latency_table[7] = { + if (cas_latency >= 5 && cas_latency <= 16) { + unsigned char cas_latency_table[] = { 0x2, /* 5 clocks */ 0x4, /* 6 clocks */ 0x6, /* 7 clocks */ 0x8, /* 8 clocks */ 0xa, /* 9 clocks */ 0xc, /* 10 clocks */ - 0xe /* 11 clocks */ + 0xe, /* 11 clocks */ + 0x1, /* 12 clocks */ + 0x3, /* 13 clocks */ + 0x5, /* 14 clocks */ + 0x7, /* 15 clocks */ + 0x9, /* 16 clocks */ }; caslat = cas_latency_table[cas_latency - 5]; + } else { + printf("Error: unsupported cas latency for mode register\n"); } + bt = 0; /* Nibble sequential */ switch (popts->burst_length) { @@ -930,6 +967,7 @@ static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr, | ((mode & 0x1) << 7) | (((caslat >> 1) & 0x7) << 4) | ((bt & 0x1) << 3) + | ((caslat & 1) << 2) | ((bl & 0x3) << 0) ); @@ -1399,73 +1437,37 @@ compute_fsl_memctl_config_regs(const memctl_options_t *popts, /* Chip Select Memory Bounds (CSn_BNDS) */ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { - unsigned long long ea = 0, sa = 0; + unsigned long long ea, sa; unsigned int cs_per_dimm = CONFIG_CHIP_SELECTS_PER_CTRL / CONFIG_DIMM_SLOTS_PER_CTLR; unsigned int dimm_number = i / cs_per_dimm; unsigned long long rank_density - = dimm_params[dimm_number].rank_density; + = dimm_params[dimm_number].rank_density >> dbw_cap_adj; - if (((i == 1) && (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1)) || - ((i == 2) && (popts->ba_intlv_ctl & 0x04)) || - ((i == 3) && (popts->ba_intlv_ctl & FSL_DDR_CS2_CS3))) { - /* - * Don't set up boundaries for unused CS - * cs1 for cs0_cs1, cs0_cs1_and_cs2_cs3, cs0_cs1_cs2_cs3 - * cs2 for cs0_cs1_cs2_cs3 - * cs3 for cs2_cs3, cs0_cs1_and_cs2_cs3, cs0_cs1_cs2_cs3 - * But we need to set the ODT_RD_CFG and - * ODT_WR_CFG for CS1_CONFIG here. - */ - set_csn_config(dimm_number, i, ddr, popts, dimm_params); - continue; - } if (dimm_params[dimm_number].n_ranks == 0) { debug("Skipping setup of CS%u " "because n_ranks on DIMM %u is 0\n", i, dimm_number); continue; } - if (popts->memctl_interleaving && popts->ba_intlv_ctl) { - /* - * This works superbank 2CS - * There are 2 or more memory controllers configured - * identically, memory is interleaved between them, - * and each controller uses rank interleaving within - * itself. Therefore the starting and ending address - * on each controller is twice the amount present on - * each controller. If any CS is not included in the - * interleaving, the memory on that CS is not accssible - * and the total memory size is reduced. The CS is also - * disabled. - */ - unsigned long long ctlr_density = 0; + if (popts->memctl_interleaving) { switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) { + case FSL_DDR_CS0_CS1_CS2_CS3: + break; case FSL_DDR_CS0_CS1: case FSL_DDR_CS0_CS1_AND_CS2_CS3: - ctlr_density = dimm_params[0].rank_density * 2; if (i > 1) cs_en = 0; break; case FSL_DDR_CS2_CS3: - ctlr_density = dimm_params[0].rank_density; + default: if (i > 0) cs_en = 0; break; - case FSL_DDR_CS0_CS1_CS2_CS3: - /* - * The four CS interleaving should have been verified by - * populate_memctl_options() - */ - ctlr_density = dimm_params[0].rank_density * 4; - break; - default: - break; } - ea = (CONFIG_NUM_DDR_CONTROLLERS * - (ctlr_density >> dbw_cap_adj)) - 1; - } - else if (!popts->memctl_interleaving && popts->ba_intlv_ctl) { + sa = common_dimm->base_address; + ea = common_dimm->total_mem - 1; + } else if (!popts->memctl_interleaving) { /* * If memory interleaving between controllers is NOT * enabled, the starting address for each memory @@ -1477,49 +1479,40 @@ compute_fsl_memctl_config_regs(const memctl_options_t *popts, */ switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) { case FSL_DDR_CS0_CS1_CS2_CS3: - /* CS0+CS1+CS2+CS3 interleaving, only CS0_CNDS - * needs to be set. - */ sa = common_dimm->base_address; - ea = sa + (4 * (rank_density >> dbw_cap_adj))-1; + ea = common_dimm->total_mem - 1; break; case FSL_DDR_CS0_CS1_AND_CS2_CS3: - /* CS0+CS1 and CS2+CS3 interleaving, CS0_CNDS - * and CS2_CNDS need to be set. - */ - if ((i == 2) && (dimm_number == 0)) { + if ((i >= 2) && (dimm_number == 0)) { sa = dimm_params[dimm_number].base_address + - 2 * (rank_density >> dbw_cap_adj); - ea = sa + 2 * (rank_density >> dbw_cap_adj) - 1; + 2 * rank_density; + ea = sa + 2 * rank_density - 1; } else { sa = dimm_params[dimm_number].base_address; - ea = sa + (2 * (rank_density >> - dbw_cap_adj)) - 1; + ea = sa + 2 * rank_density - 1; } break; case FSL_DDR_CS0_CS1: - /* CS0+CS1 interleaving, CS0_CNDS needs - * to be set - */ if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) { sa = dimm_params[dimm_number].base_address; - ea = sa + (rank_density >> dbw_cap_adj) - 1; - sa += (i % cs_per_dimm) * (rank_density >> dbw_cap_adj); - ea += (i % cs_per_dimm) * (rank_density >> dbw_cap_adj); + ea = sa + rank_density - 1; + if (i != 1) + sa += (i % cs_per_dimm) * rank_density; + ea += (i % cs_per_dimm) * rank_density; } else { sa = 0; ea = 0; } if (i == 0) - ea += (rank_density >> dbw_cap_adj); + ea += rank_density; break; case FSL_DDR_CS2_CS3: - /* CS2+CS3 interleaving*/ if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) { sa = dimm_params[dimm_number].base_address; - ea = sa + (rank_density >> dbw_cap_adj) - 1; - sa += (i % cs_per_dimm) * (rank_density >> dbw_cap_adj); - ea += (i % cs_per_dimm) * (rank_density >> dbw_cap_adj); + ea = sa + rank_density - 1; + if (i != 3) + sa += (i % cs_per_dimm) * rank_density; + ea += (i % cs_per_dimm) * rank_density; } else { sa = 0; ea = 0; @@ -1528,38 +1521,18 @@ compute_fsl_memctl_config_regs(const memctl_options_t *popts, ea += (rank_density >> dbw_cap_adj); break; default: /* No bank(chip-select) interleaving */ + sa = dimm_params[dimm_number].base_address; + ea = sa + rank_density - 1; + if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) { + sa += (i % cs_per_dimm) * rank_density; + ea += (i % cs_per_dimm) * rank_density; + } else { + sa = 0; + ea = 0; + } break; } } - else if (popts->memctl_interleaving && !popts->ba_intlv_ctl) { - /* - * Only the rank on CS0 of each memory controller may - * be used if memory controller interleaving is used - * without rank interleaving within each memory - * controller. However, the ending address programmed - * into each CS0 must be the sum of the amount of - * memory in the two CS0 ranks. - */ - if (i == 0) { - ea = (2 * (rank_density >> dbw_cap_adj)) - 1; - } - - } - else if (!popts->memctl_interleaving && !popts->ba_intlv_ctl) { - /* - * No rank interleaving and no memory controller - * interleaving. - */ - sa = dimm_params[dimm_number].base_address; - ea = sa + (rank_density >> dbw_cap_adj) - 1; - if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) { - sa += (i % cs_per_dimm) * (rank_density >> dbw_cap_adj); - ea += (i % cs_per_dimm) * (rank_density >> dbw_cap_adj); - } else { - sa = 0; - ea = 0; - } - } sa >>= 24; ea >>= 24; @@ -1574,7 +1547,7 @@ compute_fsl_memctl_config_regs(const memctl_options_t *popts, set_csn_config(dimm_number, i, ddr, popts, dimm_params); set_csn_config_2(i, ddr); } else - printf("CS%d is disabled.\n", i); + debug("CS%d is disabled.\n", i); } /* @@ -1590,7 +1563,7 @@ compute_fsl_memctl_config_regs(const memctl_options_t *popts, set_timing_cfg_0(ddr, popts); #endif - set_timing_cfg_3(ddr, common_dimm, cas_latency); + set_timing_cfg_3(ddr, popts, common_dimm, cas_latency); set_timing_cfg_1(ddr, popts, common_dimm, cas_latency); set_timing_cfg_2(ddr, popts, common_dimm, cas_latency, additive_latency); diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c b/arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c index d0a546610e..3e7c269e40 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c @@ -1,5 +1,5 @@ /* - * Copyright 2008-2009 Freescale Semiconductor, Inc. + * Copyright 2008-2012 Freescale Semiconductor, Inc. * Dave Liu <daveliu@freescale.com> * * calculate the organization and timing parameter @@ -90,6 +90,7 @@ ddr_compute_dimm_parameters(const ddr3_spd_eeprom_t *spd, { unsigned int retval; unsigned int mtb_ps; + int ftb_10th_ps; int i; if (spd->mem_type) { @@ -197,6 +198,14 @@ ddr_compute_dimm_parameters(const ddr3_spd_eeprom_t *spd, pdimm->mtb_ps = mtb_ps; /* + * FTB - fine timebase + * use 1/10th of ps as our unit to avoid floating point + * eg, 10 for 1ps, 25 for 2.5ps, 50 for 5ps + */ + ftb_10th_ps = + ((spd->ftb_div & 0xf0) >> 4) * 10 / (spd->ftb_div & 0x0f); + pdimm->ftb_10th_ps = ftb_10th_ps; + /* * sdram minimum cycle time * we assume the MTB is 0.125ns * eg: @@ -204,7 +213,8 @@ ddr_compute_dimm_parameters(const ddr3_spd_eeprom_t *spd, * =12 MTB (1.5ns) ->DDR3-1333 * =10 MTB (1.25ns) ->DDR3-1600 */ - pdimm->tCKmin_X_ps = spd->tCK_min * mtb_ps; + pdimm->tCKmin_X_ps = spd->tCK_min * mtb_ps + + (spd->fine_tCK_min * ftb_10th_ps) / 10; /* * CAS latency supported @@ -222,7 +232,8 @@ ddr_compute_dimm_parameters(const ddr3_spd_eeprom_t *spd, * DDR3-1333H 108 MTB (13.5ns) * DDR3-1600H 90 MTB (11.25ns) */ - pdimm->tAA_ps = spd->tAA_min * mtb_ps; + pdimm->tAA_ps = spd->tAA_min * mtb_ps + + (spd->fine_tAA_min * ftb_10th_ps) / 10; /* * min write recovery time @@ -239,7 +250,8 @@ ddr_compute_dimm_parameters(const ddr3_spd_eeprom_t *spd, * DDR3-1333H 108 MTB (13.5ns) * DDR3-1600H 90 MTB (11.25) */ - pdimm->tRCD_ps = spd->tRCD_min * mtb_ps; + pdimm->tRCD_ps = spd->tRCD_min * mtb_ps + + (spd->fine_tRCD_min * ftb_10th_ps) / 10; /* * min row active to row active delay time @@ -257,7 +269,8 @@ ddr_compute_dimm_parameters(const ddr3_spd_eeprom_t *spd, * DDR3-1333H 108 MTB (13.5ns) * DDR3-1600H 90 MTB (11.25ns) */ - pdimm->tRP_ps = spd->tRP_min * mtb_ps; + pdimm->tRP_ps = spd->tRP_min * mtb_ps + + (spd->fine_tRP_min * ftb_10th_ps) / 10; /* min active to precharge delay time * eg: tRAS_min = @@ -277,7 +290,7 @@ ddr_compute_dimm_parameters(const ddr3_spd_eeprom_t *spd, * DDR3-1600H 370 MTB (46.25ns) */ pdimm->tRC_ps = (((spd->tRAS_tRC_ext & 0xf0) << 4) | spd->tRC_min_lsb) - * mtb_ps; + * mtb_ps + (spd->fine_tRC_min * ftb_10th_ps) / 10; /* * min refresh recovery delay time * eg: tRFC_min = diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/interactive.c b/arch/powerpc/cpu/mpc8xxx/ddr/interactive.c index 5b724371f6..f59d1051bf 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/interactive.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/interactive.c @@ -1,5 +1,5 @@ /* - * Copyright 2010-2011 Freescale Semiconductor, Inc. + * Copyright 2010-2012 Freescale Semiconductor, Inc. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -1047,7 +1047,7 @@ void ddr3_spd_dump(const ddr3_spd_eeprom_t *spd) /* General Section: Bytes 0-59 */ -#define PRINT_NXS(x, y, z...) printf("%-3d : %02x " z "\n", x, y); +#define PRINT_NXS(x, y, z...) printf("%-3d : %02x " z "\n", x, (u8)y); #define PRINT_NNXXS(n0, n1, x0, x1, s) \ printf("%-3d-%3d: %02x %02x " s "\n", n0, n1, x0, x1); @@ -1121,11 +1121,21 @@ void ddr3_spd_dump(const ddr3_spd_eeprom_t *spd) "therm_sensor SDRAM Thermal Sensor"); PRINT_NXS(33, spd->device_type, "device_type SDRAM Device Type"); - - printf("%-3d-%3d: ", 34, 59); /* Reserved, General Section */ - - for (i = 34; i <= 59; i++) - printf("%02x ", spd->res_34_59[i - 34]); + PRINT_NXS(34, spd->fine_tCK_min, + "fine_tCK_min Fine offset for tCKmin"); + PRINT_NXS(35, spd->fine_tAA_min, + "fine_tAA_min Fine offset for tAAmin"); + PRINT_NXS(36, spd->fine_tRCD_min, + "fine_tRCD_min Fine offset for tRCDmin"); + PRINT_NXS(37, spd->fine_tRP_min, + "fine_tRP_min Fine offset for tRPmin"); + PRINT_NXS(38, spd->fine_tRC_min, + "fine_tRC_min Fine offset for tRCmin"); + + printf("%-3d-%3d: ", 39, 59); /* Reserved, General Section */ + + for (i = 39; i <= 59; i++) + printf("%02x ", spd->res_39_59[i - 39]); puts("\n"); @@ -1388,7 +1398,7 @@ unsigned long long fsl_ddr_interactive(fsl_ddr_info_t *pinfo) * No need to worry for buffer overflow here in * this function; readline() maxes out at CFG_CBSIZE */ - readline_into_buffer(prompt, buffer); + readline_into_buffer(prompt, buffer, 0); argc = parse_line(buffer, argv); if (argc == 0) continue; diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/lc_common_dimm_params.c b/arch/powerpc/cpu/mpc8xxx/ddr/lc_common_dimm_params.c index 20c7db03ed..03a784cd47 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/lc_common_dimm_params.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/lc_common_dimm_params.c @@ -1,5 +1,5 @@ /* - * Copyright 2008-2011 Freescale Semiconductor, Inc. + * Copyright 2008-2012 Freescale Semiconductor, Inc. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -27,8 +27,10 @@ compute_cas_latency_ddr3(const dimm_params_t *dimm_params, /* compute the common CAS latency supported between slots */ tmp = dimm_params[0].caslat_X; - for (i = 1; i < number_of_dimms; i++) - tmp &= dimm_params[i].caslat_X; + for (i = 1; i < number_of_dimms; i++) { + if (dimm_params[i].n_ranks) + tmp &= dimm_params[i].caslat_X; + } common_caslat = tmp; /* compute the max tAAmin tCKmin between slots */ @@ -491,5 +493,15 @@ compute_lowest_common_dimm_parameters(const dimm_params_t *dimm_params, */ outpdimm->additive_latency = additive_latency; + debug("tCKmin_ps = %u\n", outpdimm->tCKmin_X_ps); + debug("tRCD_ps = %u\n", outpdimm->tRCD_ps); + debug("tRP_ps = %u\n", outpdimm->tRP_ps); + debug("tRAS_ps = %u\n", outpdimm->tRAS_ps); + debug("tWR_ps = %u\n", outpdimm->tWR_ps); + debug("tWTR_ps = %u\n", outpdimm->tWTR_ps); + debug("tRFC_ps = %u\n", outpdimm->tRFC_ps); + debug("tRRD_ps = %u\n", outpdimm->tRRD_ps); + debug("tRC_ps = %u\n", outpdimm->tRC_ps); + return 0; } diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/main.c b/arch/powerpc/cpu/mpc8xxx/ddr/main.c index c2a03e334c..b47268c20e 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/main.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/main.c @@ -1,5 +1,5 @@ /* - * Copyright 2008-2011 Freescale Semiconductor, Inc. + * Copyright 2008-2012 Freescale Semiconductor, Inc. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -15,13 +15,15 @@ #include <common.h> #include <i2c.h> #include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_law.h> #include "ddr.h" -extern void fsl_ddr_set_lawbar( +void fsl_ddr_set_lawbar( const common_timing_params_t *memctl_common_params, unsigned int memctl_interleaved, unsigned int ctrl_num); +void fsl_ddr_set_intl3r(const unsigned int granule_size); /* processor specific function */ extern void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, @@ -51,6 +53,22 @@ u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { [1][0] = SPD_EEPROM_ADDRESS3, /* controller 2 */ [1][1] = SPD_EEPROM_ADDRESS4, /* controller 2 */ }; +#elif (CONFIG_NUM_DDR_CONTROLLERS == 3) && (CONFIG_DIMM_SLOTS_PER_CTLR == 1) +u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { + [0][0] = SPD_EEPROM_ADDRESS1, /* controller 1 */ + [1][0] = SPD_EEPROM_ADDRESS2, /* controller 2 */ + [2][0] = SPD_EEPROM_ADDRESS3, /* controller 3 */ +}; +#elif (CONFIG_NUM_DDR_CONTROLLERS == 3) && (CONFIG_DIMM_SLOTS_PER_CTLR == 2) +u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { + [0][0] = SPD_EEPROM_ADDRESS1, /* controller 1 */ + [0][1] = SPD_EEPROM_ADDRESS2, /* controller 1 */ + [1][0] = SPD_EEPROM_ADDRESS3, /* controller 2 */ + [1][1] = SPD_EEPROM_ADDRESS4, /* controller 2 */ + [2][0] = SPD_EEPROM_ADDRESS5, /* controller 3 */ + [2][1] = SPD_EEPROM_ADDRESS6, /* controller 3 */ +}; + #endif static void __get_spd(generic_spd_eeprom_t *spd, u8 i2c_address) @@ -156,12 +174,12 @@ const char * step_to_string(unsigned int step) { return step_string_tbl[s]; } -int step_assign_addresses(fsl_ddr_info_t *pinfo, - unsigned int dbw_cap_adj[], - unsigned int *all_memctl_interleaving, - unsigned int *all_ctlr_rank_interleaving) +unsigned long long step_assign_addresses(fsl_ddr_info_t *pinfo, + unsigned int dbw_cap_adj[]) { int i, j; + unsigned long long total_mem, current_mem_base, total_ctlr_mem; + unsigned long long rank_density, ctlr_density = 0; /* * If a reduced data width is requested, but the SPD @@ -220,86 +238,108 @@ int step_assign_addresses(fsl_ddr_info_t *pinfo, "specified controller %u\n", i); return 1; } + debug("dbw_cap_adj[%d]=%d\n", i, dbw_cap_adj[i]); } - j = 0; - for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) - if (pinfo->memctl_opts[i].memctl_interleaving) - j++; - /* - * Not support less than all memory controllers interleaving - * if more than two controllers - */ - if (j == CONFIG_NUM_DDR_CONTROLLERS) - *all_memctl_interleaving = 1; - - /* Check that all controllers are rank interleaving. */ - j = 0; - for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) - if (pinfo->memctl_opts[i].ba_intlv_ctl) - j++; - /* - * All memory controllers must be populated to qualify for - * all controller rank interleaving - */ - if (j == CONFIG_NUM_DDR_CONTROLLERS) - *all_ctlr_rank_interleaving = 1; - - if (*all_memctl_interleaving) { - unsigned long long addr, total_mem_per_ctlr = 0; - /* - * If interleaving between memory controllers, - * make each controller start at a base address - * of 0. - * - * Also, if bank interleaving (chip select - * interleaving) is enabled on each memory - * controller, CS0 needs to be programmed to - * cover the entire memory range on that memory - * controller - * - * Bank interleaving also implies that each - * addressed chip select is identical in size. - */ - + current_mem_base = 0ull; + total_mem = 0; + if (pinfo->memctl_opts[0].memctl_interleaving) { + rank_density = pinfo->dimm_params[0][0].rank_density >> + dbw_cap_adj[0]; + switch (pinfo->memctl_opts[0].ba_intlv_ctl & + FSL_DDR_CS0_CS1_CS2_CS3) { + case FSL_DDR_CS0_CS1_CS2_CS3: + ctlr_density = 4 * rank_density; + break; + case FSL_DDR_CS0_CS1: + case FSL_DDR_CS0_CS1_AND_CS2_CS3: + ctlr_density = 2 * rank_density; + break; + case FSL_DDR_CS2_CS3: + default: + ctlr_density = rank_density; + break; + } + debug("rank density is 0x%llx, ctlr density is 0x%llx\n", + rank_density, ctlr_density); for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { - addr = 0; - pinfo->common_timing_params[i].base_address = 0ull; - for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { - unsigned long long cap - = pinfo->dimm_params[i][j].capacity; - - pinfo->dimm_params[i][j].base_address = addr; - addr += cap >> dbw_cap_adj[i]; - total_mem_per_ctlr += cap >> dbw_cap_adj[i]; + if (pinfo->memctl_opts[i].memctl_interleaving) { + switch (pinfo->memctl_opts[i].memctl_interleaving_mode) { + case FSL_DDR_CACHE_LINE_INTERLEAVING: + case FSL_DDR_PAGE_INTERLEAVING: + case FSL_DDR_BANK_INTERLEAVING: + case FSL_DDR_SUPERBANK_INTERLEAVING: + total_ctlr_mem = 2 * ctlr_density; + break; + case FSL_DDR_3WAY_1KB_INTERLEAVING: + case FSL_DDR_3WAY_4KB_INTERLEAVING: + case FSL_DDR_3WAY_8KB_INTERLEAVING: + total_ctlr_mem = 3 * ctlr_density; + break; + case FSL_DDR_4WAY_1KB_INTERLEAVING: + case FSL_DDR_4WAY_4KB_INTERLEAVING: + case FSL_DDR_4WAY_8KB_INTERLEAVING: + total_ctlr_mem = 4 * ctlr_density; + break; + default: + panic("Unknown interleaving mode"); + } + pinfo->common_timing_params[i].base_address = + current_mem_base; + pinfo->common_timing_params[i].total_mem = + total_ctlr_mem; + total_mem = current_mem_base + total_ctlr_mem; + debug("ctrl %d base 0x%llx\n", i, current_mem_base); + debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); + } else { + /* when 3rd controller not interleaved */ + current_mem_base = total_mem; + total_ctlr_mem = 0; + pinfo->common_timing_params[i].base_address = + current_mem_base; + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { + unsigned long long cap = + pinfo->dimm_params[i][j].capacity >> dbw_cap_adj[i]; + pinfo->dimm_params[i][j].base_address = + current_mem_base; + debug("ctrl %d dimm %d base 0x%llx\n", i, j, current_mem_base); + current_mem_base += cap; + total_ctlr_mem += cap; + } + debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); + pinfo->common_timing_params[i].total_mem = + total_ctlr_mem; + total_mem += total_ctlr_mem; } } - pinfo->common_timing_params[0].total_mem = total_mem_per_ctlr; } else { /* * Simple linear assignment if memory * controllers are not interleaved. */ - unsigned long long cur_memsize = 0; for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { - u64 total_mem_per_ctlr = 0; + total_ctlr_mem = 0; pinfo->common_timing_params[i].base_address = - cur_memsize; + current_mem_base; for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { /* Compute DIMM base addresses. */ unsigned long long cap = - pinfo->dimm_params[i][j].capacity; + pinfo->dimm_params[i][j].capacity >> dbw_cap_adj[i]; pinfo->dimm_params[i][j].base_address = - cur_memsize; - cur_memsize += cap >> dbw_cap_adj[i]; - total_mem_per_ctlr += cap >> dbw_cap_adj[i]; + current_mem_base; + debug("ctrl %d dimm %d base 0x%llx\n", i, j, current_mem_base); + current_mem_base += cap; + total_ctlr_mem += cap; } + debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); pinfo->common_timing_params[i].total_mem = - total_mem_per_ctlr; + total_ctlr_mem; + total_mem += total_ctlr_mem; } } + debug("Total mem by %s is 0x%llx\n", __func__, total_mem); - return 0; + return total_mem; } unsigned long long @@ -307,8 +347,6 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, unsigned int size_only) { unsigned int i, j; - unsigned int all_controllers_memctl_interleaving = 0; - unsigned int all_controllers_rank_interleaving = 0; unsigned long long total_mem = 0; fsl_ddr_cfg_regs_t *ddr_reg = pinfo->fsl_ddr_config_reg; @@ -345,9 +383,10 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, retval = compute_dimm_parameters(spd, pdimm, i); #ifdef CONFIG_SYS_DDR_RAW_TIMING - if (retval != 0) { - printf("SPD error! Trying fallback to " - "raw timing calculation\n"); + if (!i && !j && retval) { + printf("SPD error on controller %d! " + "Trying fallback to raw timing " + "calculation\n", i); fsl_ddr_get_dimm_params(pdimm, i, j); } #else @@ -407,17 +446,14 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, &pinfo->memctl_opts[i], pinfo->dimm_params[i], i); } - check_interleaving_options(pinfo); case STEP_ASSIGN_ADDRESSES: /* STEP 5: Assign addresses to chip selects */ - step_assign_addresses(pinfo, - dbw_capacity_adjust, - &all_controllers_memctl_interleaving, - &all_controllers_rank_interleaving); + check_interleaving_options(pinfo); + total_mem = step_assign_addresses(pinfo, dbw_capacity_adjust); case STEP_COMPUTE_REGS: /* STEP 6: compute controller register values */ - debug("FSL Memory ctrl cg register computation\n"); + debug("FSL Memory ctrl register computation\n"); for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { if (timing_params[i].ndimms_present == 0) { memset(&ddr_reg[i], 0, @@ -437,21 +473,7 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, break; } - /* Compute the total amount of memory. */ - - /* - * If bank interleaving but NOT memory controller interleaving - * CS_BNDS describe the quantity of memory on each memory - * controller, so the total is the sum across. - */ - if (!all_controllers_memctl_interleaving - && all_controllers_rank_interleaving) { - total_mem = 0; - for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { - total_mem += timing_params[i].total_mem; - } - - } else { + { /* * Compute the amount of memory available just by * looking for the highest valid CSn_BNDS value. @@ -489,7 +511,7 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, phys_size_t fsl_ddr_sdram(void) { unsigned int i; - unsigned int memctl_interleaved; + unsigned int law_memctl = LAW_TRGT_IF_DDR_1; unsigned long long total_memory; fsl_ddr_info_t info; @@ -504,34 +526,6 @@ phys_size_t fsl_ddr_sdram(void) #endif total_memory = fsl_ddr_compute(&info, STEP_GET_SPD, 0); - /* Check for memory controller interleaving. */ - memctl_interleaved = 0; - for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { - memctl_interleaved += - info.memctl_opts[i].memctl_interleaving; - } - - if (memctl_interleaved) { - if (memctl_interleaved == CONFIG_NUM_DDR_CONTROLLERS) { - debug("memctl interleaving\n"); - /* - * Change the meaning of memctl_interleaved - * to be "boolean". - */ - memctl_interleaved = 1; - } else { - printf("Warning: memctl interleaving not " - "properly configured on all controllers\n"); - memctl_interleaved = 0; - for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) - info.memctl_opts[i].memctl_interleaving = 0; - debug("Recomputing with memctl_interleaving off.\n"); - total_memory = fsl_ddr_compute(&info, - STEP_ASSIGN_ADDRESSES, - 0); - } - } - /* Program configuration registers. */ for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { debug("Programming controller %u\n", i); @@ -544,24 +538,69 @@ phys_size_t fsl_ddr_sdram(void) fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]), i); } - if (memctl_interleaved) { - const unsigned int ctrl_num = 0; - - /* Only set LAWBAR1 if memory controller interleaving is on. */ - fsl_ddr_set_lawbar(&info.common_timing_params[0], - memctl_interleaved, ctrl_num); - } else { - /* - * Memory controller interleaving is NOT on; - * set each lawbar individually. - */ - for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + /* program LAWs */ + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + if (info.memctl_opts[i].memctl_interleaving) { + switch (info.memctl_opts[i].memctl_interleaving_mode) { + case FSL_DDR_CACHE_LINE_INTERLEAVING: + case FSL_DDR_PAGE_INTERLEAVING: + case FSL_DDR_BANK_INTERLEAVING: + case FSL_DDR_SUPERBANK_INTERLEAVING: + if (i == 0) { + law_memctl = LAW_TRGT_IF_DDR_INTRLV; + fsl_ddr_set_lawbar(&info.common_timing_params[i], + law_memctl, i); + } else if (i == 2) { + law_memctl = LAW_TRGT_IF_DDR_INTLV_34; + fsl_ddr_set_lawbar(&info.common_timing_params[i], + law_memctl, i); + } + break; + case FSL_DDR_3WAY_1KB_INTERLEAVING: + case FSL_DDR_3WAY_4KB_INTERLEAVING: + case FSL_DDR_3WAY_8KB_INTERLEAVING: + law_memctl = LAW_TRGT_IF_DDR_INTLV_123; + if (i == 0) { + fsl_ddr_set_intl3r(info.memctl_opts[i].memctl_interleaving_mode); + fsl_ddr_set_lawbar(&info.common_timing_params[i], + law_memctl, i); + } + break; + case FSL_DDR_4WAY_1KB_INTERLEAVING: + case FSL_DDR_4WAY_4KB_INTERLEAVING: + case FSL_DDR_4WAY_8KB_INTERLEAVING: + law_memctl = LAW_TRGT_IF_DDR_INTLV_1234; + if (i == 0) + fsl_ddr_set_lawbar(&info.common_timing_params[i], + law_memctl, i); + /* place holder for future 4-way interleaving */ + break; + default: + break; + } + } else { + switch (i) { + case 0: + law_memctl = LAW_TRGT_IF_DDR_1; + break; + case 1: + law_memctl = LAW_TRGT_IF_DDR_2; + break; + case 2: + law_memctl = LAW_TRGT_IF_DDR_3; + break; + case 3: + law_memctl = LAW_TRGT_IF_DDR_4; + break; + default: + break; + } fsl_ddr_set_lawbar(&info.common_timing_params[i], - 0, i); + law_memctl, i); } } - debug("total_memory = %llu\n", total_memory); + debug("total_memory by %s = %llu\n", __func__, total_memory); #if !defined(CONFIG_PHYS_64BIT) /* Check for 4G or more. Bad. */ diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/options.c b/arch/powerpc/cpu/mpc8xxx/ddr/options.c index 00ec57be1f..13e4825274 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/options.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/options.c @@ -1,5 +1,5 @@ /* - * Copyright 2008, 2010-2011 Freescale Semiconductor, Inc. + * Copyright 2008, 2010-2012 Freescale Semiconductor, Inc. * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the Free @@ -19,7 +19,6 @@ * This is pretty fragile on both the use of stack and if the buffer is big * enough. However we will get a warning from getenv_f for the later. */ -#define HWCONFIG_BUFFER_SIZE 128 /* Board-specific functions defined in each board's ddr.c */ extern void fsl_ddr_board_options(memctl_options_t *popts, @@ -790,46 +789,97 @@ unsigned int populate_memctl_options(int all_DIMMs_registered, * should be a subset of the requested configuration. */ #if (CONFIG_NUM_DDR_CONTROLLERS > 1) - if (hwconfig_sub_f("fsl_ddr", "ctlr_intlv", buf)) { - if (pdimm[0].n_ranks == 0) { - printf("There is no rank on CS0 for controller %d. Because only" - " rank on CS0 and ranks chip-select interleaved with CS0" - " are controller interleaved, force non memory " - "controller interleaving\n", ctrl_num); - popts->memctl_interleaving = 0; - } else { - popts->memctl_interleaving = 1; - /* - * test null first. if CONFIG_HWCONFIG is not defined - * hwconfig_arg_cmp returns non-zero - */ - if (hwconfig_subarg_cmp_f("fsl_ddr", "ctlr_intlv", - "null", buf)) { - popts->memctl_interleaving = 0; - debug("memory controller interleaving disabled.\n"); - } else if (hwconfig_subarg_cmp_f("fsl_ddr", - "ctlr_intlv", - "cacheline", buf)) - popts->memctl_interleaving_mode = - FSL_DDR_CACHE_LINE_INTERLEAVING; - else if (hwconfig_subarg_cmp_f("fsl_ddr", "ctlr_intlv", - "page", buf)) - popts->memctl_interleaving_mode = - FSL_DDR_PAGE_INTERLEAVING; - else if (hwconfig_subarg_cmp_f("fsl_ddr", "ctlr_intlv", - "bank", buf)) - popts->memctl_interleaving_mode = - FSL_DDR_BANK_INTERLEAVING; - else if (hwconfig_subarg_cmp_f("fsl_ddr", "ctlr_intlv", - "superbank", buf)) - popts->memctl_interleaving_mode = - FSL_DDR_SUPERBANK_INTERLEAVING; - else { - popts->memctl_interleaving = 0; - printf("hwconfig has unrecognized parameter for ctlr_intlv.\n"); - } - } + if (!hwconfig_sub_f("fsl_ddr", "ctlr_intlv", buf)) + goto done; + + if (pdimm[0].n_ranks == 0) { + printf("There is no rank on CS0 for controller %d.\n", ctrl_num); + popts->memctl_interleaving = 0; + goto done; + } + popts->memctl_interleaving = 1; + /* + * test null first. if CONFIG_HWCONFIG is not defined + * hwconfig_arg_cmp returns non-zero + */ + if (hwconfig_subarg_cmp_f("fsl_ddr", "ctlr_intlv", + "null", buf)) { + popts->memctl_interleaving = 0; + debug("memory controller interleaving disabled.\n"); + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "cacheline", buf)) { + popts->memctl_interleaving_mode = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : FSL_DDR_CACHE_LINE_INTERLEAVING; + popts->memctl_interleaving = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : 1; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "page", buf)) { + popts->memctl_interleaving_mode = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : FSL_DDR_PAGE_INTERLEAVING; + popts->memctl_interleaving = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : 1; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "bank", buf)) { + popts->memctl_interleaving_mode = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : FSL_DDR_BANK_INTERLEAVING; + popts->memctl_interleaving = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : 1; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "superbank", buf)) { + popts->memctl_interleaving_mode = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : FSL_DDR_SUPERBANK_INTERLEAVING; + popts->memctl_interleaving = + ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? + 0 : 1; +#if (CONFIG_NUM_DDR_CONTROLLERS == 3) + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "3way_1KB", buf)) { + popts->memctl_interleaving_mode = + FSL_DDR_3WAY_1KB_INTERLEAVING; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "3way_4KB", buf)) { + popts->memctl_interleaving_mode = + FSL_DDR_3WAY_4KB_INTERLEAVING; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "3way_8KB", buf)) { + popts->memctl_interleaving_mode = + FSL_DDR_3WAY_8KB_INTERLEAVING; +#elif (CONFIG_NUM_DDR_CONTROLLERS == 4) + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "4way_1KB", buf)) { + popts->memctl_interleaving_mode = + FSL_DDR_4WAY_1KB_INTERLEAVING; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "4way_4KB", buf)) { + popts->memctl_interleaving_mode = + FSL_DDR_4WAY_4KB_INTERLEAVING; + } else if (hwconfig_subarg_cmp_f("fsl_ddr", + "ctlr_intlv", + "4way_8KB", buf)) { + popts->memctl_interleaving_mode = + FSL_DDR_4WAY_8KB_INTERLEAVING; +#endif + } else { + popts->memctl_interleaving = 0; + printf("hwconfig has unrecognized parameter for ctlr_intlv.\n"); } +done: #endif if ((hwconfig_sub_f("fsl_ddr", "bank_intlv", buf)) && (CONFIG_CHIP_SELECTS_PER_CTRL > 1)) { @@ -859,20 +909,20 @@ unsigned int populate_memctl_options(int all_DIMMs_registered, popts->ba_intlv_ctl = 0; printf("Not enough bank(chip-select) for " "CS0+CS1+CS2+CS3 on controller %d, " - "force non-interleaving!\n", ctrl_num); + "interleaving disabled!\n", ctrl_num); } #elif (CONFIG_DIMM_SLOTS_PER_CTLR == 2) if ((pdimm[0].n_ranks < 2) && (pdimm[1].n_ranks < 2)) { popts->ba_intlv_ctl = 0; printf("Not enough bank(chip-select) for " "CS0+CS1+CS2+CS3 on controller %d, " - "force non-interleaving!\n", ctrl_num); + "interleaving disabled!\n", ctrl_num); } if (pdimm[0].capacity != pdimm[1].capacity) { popts->ba_intlv_ctl = 0; printf("Not identical DIMM size for " "CS0+CS1+CS2+CS3 on controller %d, " - "force non-interleaving!\n", ctrl_num); + "interleaving disabled!\n", ctrl_num); } #endif break; @@ -881,7 +931,7 @@ unsigned int populate_memctl_options(int all_DIMMs_registered, popts->ba_intlv_ctl = 0; printf("Not enough bank(chip-select) for " "CS0+CS1 on controller %d, " - "force non-interleaving!\n", ctrl_num); + "interleaving disabled!\n", ctrl_num); } break; case FSL_DDR_CS2_CS3: @@ -889,13 +939,13 @@ unsigned int populate_memctl_options(int all_DIMMs_registered, if (pdimm[0].n_ranks < 4) { popts->ba_intlv_ctl = 0; printf("Not enough bank(chip-select) for CS2+CS3 " - "on controller %d, force non-interleaving!\n", ctrl_num); + "on controller %d, interleaving disabled!\n", ctrl_num); } #elif (CONFIG_DIMM_SLOTS_PER_CTLR == 2) if (pdimm[1].n_ranks < 2) { popts->ba_intlv_ctl = 0; printf("Not enough bank(chip-select) for CS2+CS3 " - "on controller %d, force non-interleaving!\n", ctrl_num); + "on controller %d, interleaving disabled!\n", ctrl_num); } #endif break; @@ -905,14 +955,14 @@ unsigned int populate_memctl_options(int all_DIMMs_registered, popts->ba_intlv_ctl = 0; printf("Not enough bank(CS) for CS0+CS1 and " "CS2+CS3 on controller %d, " - "force non-interleaving!\n", ctrl_num); + "interleaving disabled!\n", ctrl_num); } #elif (CONFIG_DIMM_SLOTS_PER_CTLR == 2) if ((pdimm[0].n_ranks < 2) || (pdimm[1].n_ranks < 2)) { popts->ba_intlv_ctl = 0; printf("Not enough bank(CS) for CS0+CS1 and " "CS2+CS3 on controller %d, " - "force non-interleaving!\n", ctrl_num); + "interleaving disabled!\n", ctrl_num); } #endif break; @@ -954,33 +1004,73 @@ unsigned int populate_memctl_options(int all_DIMMs_registered, void check_interleaving_options(fsl_ddr_info_t *pinfo) { - int i, j, check_n_ranks, intlv_fixed = 0; + int i, j, k, check_n_ranks, intlv_invalid = 0; + unsigned int check_intlv, check_n_row_addr, check_n_col_addr; unsigned long long check_rank_density; + struct dimm_params_s *dimm; /* * Check if all controllers are configured for memory * controller interleaving. Identical dimms are recommended. At least - * the size should be checked. + * the size, row and col address should be checked. */ j = 0; check_n_ranks = pinfo->dimm_params[0][0].n_ranks; check_rank_density = pinfo->dimm_params[0][0].rank_density; + check_n_row_addr = pinfo->dimm_params[0][0].n_row_addr; + check_n_col_addr = pinfo->dimm_params[0][0].n_col_addr; + check_intlv = pinfo->memctl_opts[0].memctl_interleaving_mode; for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { - if ((pinfo->memctl_opts[i].memctl_interleaving) && \ - (check_rank_density == pinfo->dimm_params[i][0].rank_density) && \ - (check_n_ranks == pinfo->dimm_params[i][0].n_ranks)) { + dimm = &pinfo->dimm_params[i][0]; + if (!pinfo->memctl_opts[i].memctl_interleaving) { + continue; + } else if (((check_rank_density != dimm->rank_density) || + (check_n_ranks != dimm->n_ranks) || + (check_n_row_addr != dimm->n_row_addr) || + (check_n_col_addr != dimm->n_col_addr) || + (check_intlv != + pinfo->memctl_opts[i].memctl_interleaving_mode))){ + intlv_invalid = 1; + break; + } else { j++; } + } - if (j != CONFIG_NUM_DDR_CONTROLLERS) { + if (intlv_invalid) { for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) - if (pinfo->memctl_opts[i].memctl_interleaving) { + pinfo->memctl_opts[i].memctl_interleaving = 0; + printf("Not all DIMMs are identical. " + "Memory controller interleaving disabled.\n"); + } else { + switch (check_intlv) { + case FSL_DDR_CACHE_LINE_INTERLEAVING: + case FSL_DDR_PAGE_INTERLEAVING: + case FSL_DDR_BANK_INTERLEAVING: + case FSL_DDR_SUPERBANK_INTERLEAVING: + if (3 == CONFIG_NUM_DDR_CONTROLLERS) + k = 2; + else + k = CONFIG_NUM_DDR_CONTROLLERS; + break; + case FSL_DDR_3WAY_1KB_INTERLEAVING: + case FSL_DDR_3WAY_4KB_INTERLEAVING: + case FSL_DDR_3WAY_8KB_INTERLEAVING: + case FSL_DDR_4WAY_1KB_INTERLEAVING: + case FSL_DDR_4WAY_4KB_INTERLEAVING: + case FSL_DDR_4WAY_8KB_INTERLEAVING: + default: + k = CONFIG_NUM_DDR_CONTROLLERS; + break; + } + debug("%d of %d controllers are interleaving.\n", j, k); + if (j != k) { + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) pinfo->memctl_opts[i].memctl_interleaving = 0; - intlv_fixed = 1; - } - if (intlv_fixed) - printf("Not all DIMMs are identical in size. " - "Memory controller interleaving disabled.\n"); + printf("Not all controllers have compatible " + "interleaving mode. All disabled.\n"); + } } + debug("Checking interleaving options completed\n"); } int fsl_use_spd(void) diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/util.c b/arch/powerpc/cpu/mpc8xxx/ddr/util.c index eb6a17a850..664ad09298 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/util.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/util.c @@ -1,5 +1,5 @@ /* - * Copyright 2008-2011 Freescale Semiconductor, Inc. + * Copyright 2008-2012 Freescale Semiconductor, Inc. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -79,7 +79,7 @@ unsigned int mclk_to_picos(unsigned int mclk) void __fsl_ddr_set_lawbar(const common_timing_params_t *memctl_common_params, - unsigned int memctl_interleaved, + unsigned int law_memctl, unsigned int ctrl_num) { unsigned long long base = memctl_common_params->base_address; @@ -98,28 +98,13 @@ __fsl_ddr_set_lawbar(const common_timing_params_t *memctl_common_params, if ((base + size) >= CONFIG_MAX_MEM_MAPPED) size = CONFIG_MAX_MEM_MAPPED - base; #endif - - if (ctrl_num == 0) { - /* - * Set up LAW for DDR controller 1 space. - */ - unsigned int lawbar1_target_id = memctl_interleaved - ? LAW_TRGT_IF_DDR_INTRLV : LAW_TRGT_IF_DDR_1; - - if (set_ddr_laws(base, size, lawbar1_target_id) < 0) { - printf("%s: ERROR (ctrl #0, intrlv=%d)\n", __func__, - memctl_interleaved); - return ; - } - } else if (ctrl_num == 1) { - if (set_ddr_laws(base, size, LAW_TRGT_IF_DDR_2) < 0) { - printf("%s: ERROR (ctrl #1)\n", __func__); - return ; - } - } else { - printf("%s: unexpected DDR controller number (%u)\n", __func__, - ctrl_num); + if (set_ddr_laws(base, size, law_memctl) < 0) { + printf("%s: ERROR (ctrl #%d, TRGT ID=%x)\n", __func__, ctrl_num, + law_memctl); + return ; } + debug("setup ddr law base = 0x%llx, size 0x%llx, TRGT_ID 0x%x\n", + base, size, law_memctl); } __attribute__((weak, alias("__fsl_ddr_set_lawbar"))) void @@ -127,6 +112,15 @@ fsl_ddr_set_lawbar(const common_timing_params_t *memctl_common_params, unsigned int memctl_interleaved, unsigned int ctrl_num); +void fsl_ddr_set_intl3r(const unsigned int granule_size) +{ +#ifdef CONFIG_E6500 + u32 *mcintl3r = (void *) (CONFIG_SYS_IMMR + 0x18004); + *mcintl3r = 0x80000000 | (granule_size & 0x1f); + debug("Enable MCINTL3R with granule size 0x%x\n", granule_size); +#endif +} + void board_add_ram_info(int use_default) { #if defined(CONFIG_MPC83xx) @@ -137,6 +131,9 @@ void board_add_ram_info(int use_default) #elif defined(CONFIG_MPC86xx) ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_MPC86xx_DDR_ADDR); #endif +#if defined(CONFIG_E6500) && (CONFIG_NUM_DDR_CONTROLLERS == 3) + u32 *mcintl3r = (void *) (CONFIG_SYS_IMMR + 0x18004); +#endif #if (CONFIG_NUM_DDR_CONTROLLERS > 1) uint32_t cs0_config = in_be32(&ddr->cs0_config); #endif @@ -180,7 +177,29 @@ void board_add_ram_info(int use_default) else puts(", ECC off)"); -#if (CONFIG_NUM_DDR_CONTROLLERS > 1) +#if (CONFIG_NUM_DDR_CONTROLLERS == 3) +#ifdef CONFIG_E6500 + if (*mcintl3r & 0x80000000) { + puts("\n"); + puts(" DDR Controller Interleaving Mode: "); + switch (*mcintl3r & 0x1f) { + case FSL_DDR_3WAY_1KB_INTERLEAVING: + puts("3-way 1KB"); + break; + case FSL_DDR_3WAY_4KB_INTERLEAVING: + puts("3-way 4KB"); + break; + case FSL_DDR_3WAY_8KB_INTERLEAVING: + puts("3-way 8KB"); + break; + default: + puts("3-way UNKNOWN"); + break; + } + } +#endif +#endif +#if (CONFIG_NUM_DDR_CONTROLLERS >= 2) if (cs0_config & 0x20000000) { puts("\n"); puts(" DDR Controller Interleaving Mode: "); diff --git a/arch/powerpc/cpu/mpc8xxx/fdt.c b/arch/powerpc/cpu/mpc8xxx/fdt.c index 09810be7d3..32ab050962 100644 --- a/arch/powerpc/cpu/mpc8xxx/fdt.c +++ b/arch/powerpc/cpu/mpc8xxx/fdt.c @@ -62,8 +62,9 @@ void ft_fixup_num_cores(void *blob) { off = fdt_node_offset_by_prop_value(blob, -1, "device_type", "cpu", 4); while (off != -FDT_ERR_NOTFOUND) { u32 *reg = (u32 *)fdt_getprop(blob, off, "reg", 0); + u32 phys_cpu_id = thread_to_core(*reg); - if (!is_core_valid(*reg) || is_core_disabled(*reg)) { + if (!is_core_valid(phys_cpu_id) || is_core_disabled(phys_cpu_id)) { int ph = fdt_get_phandle(blob, off); /* Delete the cpu node once there are no cpu handles */ diff --git a/arch/powerpc/cpu/mpc8xxx/fsl_ifc.c b/arch/powerpc/cpu/mpc8xxx/fsl_ifc.c index 66824960d3..56b319f5d4 100644 --- a/arch/powerpc/cpu/mpc8xxx/fsl_ifc.c +++ b/arch/powerpc/cpu/mpc8xxx/fsl_ifc.c @@ -44,12 +44,18 @@ void init_early_memctl_regs(void) set_ifc_ftim(IFC_CS0, IFC_FTIM3, CONFIG_SYS_CS0_FTIM3); #if !defined(CONFIG_SYS_FSL_ERRATUM_IFC_A003399) || defined(CONFIG_SYS_RAMBOOT) +#ifdef CONFIG_SYS_CSPR0_EXT + set_ifc_cspr_ext(IFC_CS0, CONFIG_SYS_CSPR0_EXT); +#endif set_ifc_cspr(IFC_CS0, CONFIG_SYS_CSPR0); set_ifc_amask(IFC_CS0, CONFIG_SYS_AMASK0); set_ifc_csor(IFC_CS0, CONFIG_SYS_CSOR0); #endif #endif +#ifdef CONFIG_SYS_CSPR1_EXT + set_ifc_cspr_ext(IFC_CS1, CONFIG_SYS_CSPR1_EXT); +#endif #if defined(CONFIG_SYS_CSPR1) && defined(CONFIG_SYS_CSOR1) set_ifc_ftim(IFC_CS1, IFC_FTIM0, CONFIG_SYS_CS1_FTIM0); set_ifc_ftim(IFC_CS1, IFC_FTIM1, CONFIG_SYS_CS1_FTIM1); @@ -61,6 +67,9 @@ void init_early_memctl_regs(void) set_ifc_cspr(IFC_CS1, CONFIG_SYS_CSPR1); #endif +#ifdef CONFIG_SYS_CSPR2_EXT + set_ifc_cspr_ext(IFC_CS2, CONFIG_SYS_CSPR2_EXT); +#endif #if defined(CONFIG_SYS_CSPR2) && defined(CONFIG_SYS_CSOR2) set_ifc_ftim(IFC_CS2, IFC_FTIM0, CONFIG_SYS_CS2_FTIM0); set_ifc_ftim(IFC_CS2, IFC_FTIM1, CONFIG_SYS_CS2_FTIM1); @@ -72,6 +81,9 @@ void init_early_memctl_regs(void) set_ifc_cspr(IFC_CS2, CONFIG_SYS_CSPR2); #endif +#ifdef CONFIG_SYS_CSPR3_EXT + set_ifc_cspr_ext(IFC_CS3, CONFIG_SYS_CSPR3_EXT); +#endif #if defined(CONFIG_SYS_CSPR3) && defined(CONFIG_SYS_CSOR3) set_ifc_ftim(IFC_CS3, IFC_FTIM0, CONFIG_SYS_CS3_FTIM0); set_ifc_ftim(IFC_CS3, IFC_FTIM1, CONFIG_SYS_CS3_FTIM1); diff --git a/arch/powerpc/cpu/mpc8xxx/srio.c b/arch/powerpc/cpu/mpc8xxx/srio.c index c7f394972b..0cb65b32e4 100644 --- a/arch/powerpc/cpu/mpc8xxx/srio.c +++ b/arch/powerpc/cpu/mpc8xxx/srio.c @@ -95,126 +95,92 @@ void srio_init(void) } } -#ifdef CONFIG_SRIOBOOT_MASTER -void srio_boot_master(void) +#ifdef CONFIG_FSL_CORENET +void srio_boot_master(int port) { struct ccsr_rio *srio = (void *)CONFIG_SYS_FSL_SRIO_ADDR; /* set port accept-all */ - out_be32((void *)&srio->impl.port[CONFIG_SRIOBOOT_MASTER_PORT].ptaacr, + out_be32((void *)&srio->impl.port[port - 1].ptaacr, SRIO_PORT_ACCEPT_ALL); - debug("SRIOBOOT - MASTER: Master port [ %d ] for srio boot.\n", - CONFIG_SRIOBOOT_MASTER_PORT); + debug("SRIOBOOT - MASTER: Master port [ %d ] for srio boot.\n", port); /* configure inbound window for slave's u-boot image */ debug("SRIOBOOT - MASTER: Inbound window for slave's image; " "Local = 0x%llx, Srio = 0x%llx, Size = 0x%x\n", - (u64)CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS1, - (u64)CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS1, - CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[0].riwtar, - CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS1 >> 12); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[0].riwbar, - CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS1 >> 12); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[0].riwar, + (u64)CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS, + (u64)CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1, + CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE); + out_be32((void *)&srio->atmu.port[port - 1].inbw[0].riwtar, + CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS >> 12); + out_be32((void *)&srio->atmu.port[port - 1].inbw[0].riwbar, + CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 >> 12); + out_be32((void *)&srio->atmu.port[port - 1].inbw[0].riwar, SRIO_IB_ATMU_AR - | atmu_size_mask(CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE)); + | atmu_size_mask(CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE)); /* configure inbound window for slave's u-boot image */ debug("SRIOBOOT - MASTER: Inbound window for slave's image; " "Local = 0x%llx, Srio = 0x%llx, Size = 0x%x\n", - (u64)CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS2, - (u64)CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS2, - CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[1].riwtar, - CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS2 >> 12); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[1].riwbar, - CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS2 >> 12); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[1].riwar, + (u64)CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS, + (u64)CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2, + CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE); + out_be32((void *)&srio->atmu.port[port - 1].inbw[1].riwtar, + CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS >> 12); + out_be32((void *)&srio->atmu.port[port - 1].inbw[1].riwbar, + CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 >> 12); + out_be32((void *)&srio->atmu.port[port - 1].inbw[1].riwar, SRIO_IB_ATMU_AR - | atmu_size_mask(CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE)); + | atmu_size_mask(CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE)); - /* configure inbound window for slave's ucode */ - debug("SRIOBOOT - MASTER: Inbound window for slave's ucode; " + /* configure inbound window for slave's ucode and ENV */ + debug("SRIOBOOT - MASTER: Inbound window for slave's ucode and ENV; " "Local = 0x%llx, Srio = 0x%llx, Size = 0x%x\n", - (u64)CONFIG_SRIOBOOT_SLAVE_UCODE_LAW_PHYS, - (u64)CONFIG_SRIOBOOT_SLAVE_UCODE_SRIO_PHYS, - CONFIG_SRIOBOOT_SLAVE_UCODE_SIZE); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[2].riwtar, - CONFIG_SRIOBOOT_SLAVE_UCODE_LAW_PHYS >> 12); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[2].riwbar, - CONFIG_SRIOBOOT_SLAVE_UCODE_SRIO_PHYS >> 12); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[2].riwar, - SRIO_IB_ATMU_AR - | atmu_size_mask(CONFIG_SRIOBOOT_SLAVE_UCODE_SIZE)); - - /* configure inbound window for slave's ENV */ - debug("SRIOBOOT - MASTER: Inbound window for slave's ENV; " - "Local = 0x%llx, Siro = 0x%llx, Size = 0x%x\n", - CONFIG_SRIOBOOT_SLAVE_ENV_LAW_PHYS, - CONFIG_SRIOBOOT_SLAVE_ENV_SRIO_PHYS, - CONFIG_SRIOBOOT_SLAVE_ENV_SIZE); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[3].riwtar, - CONFIG_SRIOBOOT_SLAVE_ENV_LAW_PHYS >> 12); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[3].riwbar, - CONFIG_SRIOBOOT_SLAVE_ENV_SRIO_PHYS >> 12); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[3].riwar, + (u64)CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS, + (u64)CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS, + CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE); + out_be32((void *)&srio->atmu.port[port - 1].inbw[2].riwtar, + CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS >> 12); + out_be32((void *)&srio->atmu.port[port - 1].inbw[2].riwbar, + CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS >> 12); + out_be32((void *)&srio->atmu.port[port - 1].inbw[2].riwar, SRIO_IB_ATMU_AR - | atmu_size_mask(CONFIG_SRIOBOOT_SLAVE_ENV_SIZE)); + | atmu_size_mask(CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE)); } -#ifdef CONFIG_SRIOBOOT_SLAVE_HOLDOFF -void srio_boot_master_release_slave(void) +void srio_boot_master_release_slave(int port) { struct ccsr_rio *srio = (void *)CONFIG_SYS_FSL_SRIO_ADDR; u32 escsr; debug("SRIOBOOT - MASTER: " "Check the port status and release slave core ...\n"); - escsr = in_be32((void *)&srio->lp_serial - .port[CONFIG_SRIOBOOT_MASTER_PORT].pescsr); + escsr = in_be32((void *)&srio->lp_serial.port[port - 1].pescsr); if (escsr & 0x2) { if (escsr & 0x10100) { debug("SRIOBOOT - MASTER: Port [ %d ] is error.\n", - CONFIG_SRIOBOOT_MASTER_PORT); + port); } else { debug("SRIOBOOT - MASTER: " - "Port [ %d ] is ready, now release slave's core ...\n", - CONFIG_SRIOBOOT_MASTER_PORT); + "Port [ %d ] is ready, now release slave's core ...\n", + port); /* * configure outbound window * with maintenance attribute to set slave's LCSBA1CSR */ - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT] + out_be32((void *)&srio->atmu.port[port - 1] .outbw[1].rowtar, 0); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT] + out_be32((void *)&srio->atmu.port[port - 1] .outbw[1].rowtear, 0); - if (CONFIG_SRIOBOOT_MASTER_PORT) - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT] + if (port - 1) + out_be32((void *)&srio->atmu.port[port - 1] .outbw[1].rowbar, CONFIG_SYS_SRIO2_MEM_PHYS >> 12); else - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT] + out_be32((void *)&srio->atmu.port[port - 1] .outbw[1].rowbar, CONFIG_SYS_SRIO1_MEM_PHYS >> 12); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT] + out_be32((void *)&srio->atmu.port[port - 1] .outbw[1].rowar, SRIO_OB_ATMU_AR_MAINT | atmu_size_mask(SRIO_MAINT_WIN_SIZE)); @@ -223,27 +189,22 @@ void srio_boot_master_release_slave(void) * configure outbound window * with R/W attribute to set slave's BRR */ - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT] + out_be32((void *)&srio->atmu.port[port - 1] .outbw[2].rowtar, SRIO_LCSBA1CSR >> 9); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT] + out_be32((void *)&srio->atmu.port[port - 1] .outbw[2].rowtear, 0); - if (CONFIG_SRIOBOOT_MASTER_PORT) - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT] + if (port - 1) + out_be32((void *)&srio->atmu.port[port - 1] .outbw[2].rowbar, (CONFIG_SYS_SRIO2_MEM_PHYS + SRIO_MAINT_WIN_SIZE) >> 12); else - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT] + out_be32((void *)&srio->atmu.port[port - 1] .outbw[2].rowbar, (CONFIG_SYS_SRIO1_MEM_PHYS + SRIO_MAINT_WIN_SIZE) >> 12); - out_be32((void *)&srio->atmu - .port[CONFIG_SRIOBOOT_MASTER_PORT] + out_be32((void *)&srio->atmu.port[port - 1] .outbw[2].rowar, SRIO_OB_ATMU_AR_RW | atmu_size_mask(SRIO_RW_WIN_SIZE)); @@ -252,7 +213,7 @@ void srio_boot_master_release_slave(void) * Set the LCSBA1CSR register in slave * by the maint-outbound window */ - if (CONFIG_SRIOBOOT_MASTER_PORT) { + if (port - 1) { out_be32((void *)CONFIG_SYS_SRIO2_MEM_VIRT + SRIO_LCSBA1CSR_OFFSET, SRIO_LCSBA1CSR); @@ -266,8 +227,8 @@ void srio_boot_master_release_slave(void) */ out_be32((void *)CONFIG_SYS_SRIO2_MEM_VIRT + SRIO_MAINT_WIN_SIZE - + CONFIG_SRIOBOOT_SLAVE_BRR_OFFSET, - CONFIG_SRIOBOOT_SLAVE_RELEASE_MASK); + + CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET, + CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK); } else { out_be32((void *)CONFIG_SYS_SRIO1_MEM_VIRT + SRIO_LCSBA1CSR_OFFSET, @@ -282,15 +243,13 @@ void srio_boot_master_release_slave(void) */ out_be32((void *)CONFIG_SYS_SRIO1_MEM_VIRT + SRIO_MAINT_WIN_SIZE - + CONFIG_SRIOBOOT_SLAVE_BRR_OFFSET, - CONFIG_SRIOBOOT_SLAVE_RELEASE_MASK); + + CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET, + CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK); } debug("SRIOBOOT - MASTER: " "Release slave successfully! Now the slave should start up!\n"); } } else - debug("SRIOBOOT - MASTER: Port [ %d ] is not ready.\n", - CONFIG_SRIOBOOT_MASTER_PORT); + debug("SRIOBOOT - MASTER: Port [ %d ] is not ready.\n", port); } #endif -#endif diff --git a/arch/powerpc/include/asm/config.h b/arch/powerpc/include/asm/config.h index d138636939..67cea01aae 100644 --- a/arch/powerpc/include/asm/config.h +++ b/arch/powerpc/include/asm/config.h @@ -29,6 +29,10 @@ #include <asm/config_mpc86xx.h> #endif +#ifndef HWCONFIG_BUFFER_SIZE + #define HWCONFIG_BUFFER_SIZE 256 +#endif + /* CONFIG_HARD_SPI triggers SPI bus initialization in PowerPC */ #if defined(CONFIG_MPC8XXX_SPI) || defined(CONFIG_FSL_ESPI) # ifndef CONFIG_HARD_SPI diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index b6c44bb11d..aa27741a92 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -37,6 +37,7 @@ #if defined(CONFIG_MPC8536) #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 12 +#define CONFIG_SYS_PPC_E500_DEBUG_TLB 1 #define CONFIG_SYS_FSL_SEC_COMPAT 2 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 @@ -54,12 +55,14 @@ #elif defined(CONFIG_MPC8544) #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 10 +#define CONFIG_SYS_PPC_E500_DEBUG_TLB 0 #define CONFIG_SYS_FSL_SEC_COMPAT 2 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #elif defined(CONFIG_MPC8548) #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 10 +#define CONFIG_SYS_PPC_E500_DEBUG_TLB 0 #define CONFIG_SYS_FSL_SEC_COMPAT 2 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_NMG_DDR120 @@ -113,6 +116,7 @@ #elif defined(CONFIG_MPC8572) #define CONFIG_MAX_CPUS 2 #define CONFIG_SYS_FSL_NUM_LAWS 12 +#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2 #define CONFIG_SYS_FSL_SEC_COMPAT 2 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_DDR_115 @@ -191,33 +195,6 @@ #define CONFIG_SYS_FSL_ERRATUM_P1010_A003549 #define CONFIG_SYS_FSL_ERRATUM_IFC_A003399 -/* P1015 is single core version of P1024 */ -#elif defined(CONFIG_P1015) -#define CONFIG_MAX_CPUS 1 -#define CONFIG_SYS_FSL_NUM_LAWS 12 -#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2 -#define CONFIG_TSECV2 -#define CONFIG_FSL_PCIE_DISABLE_ASPM -#define CONFIG_SYS_FSL_SEC_COMPAT 2 -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 -#define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 -#define CONFIG_SYS_FSL_ERRATUM_ESDHC111 - -/* P1016 is single core version of P1025 */ -#elif defined(CONFIG_P1016) -#define CONFIG_MAX_CPUS 1 -#define CONFIG_SYS_FSL_NUM_LAWS 12 -#define CONFIG_SYS_PPC_E500_DEBUG_TLB 2 -#define CONFIG_TSECV2 -#define CONFIG_FSL_PCIE_DISABLE_ASPM -#define CONFIG_SYS_FSL_SEC_COMPAT 2 -#define CONFIG_SYS_FSL_ERRATUM_ELBC_A001 -#define CONFIG_SYS_FSL_ERRATUM_ESDHC111 -#define QE_MURAM_SIZE 0x6000UL -#define MAX_QE_RISC 1 -#define QE_NUM_OF_SNUM 28 -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 - /* P1017 is single core version of P1023 */ #elif defined(CONFIG_P1017) #define CONFIG_MAX_CPUS 1 @@ -333,30 +310,7 @@ #define CONFIG_SYS_FSL_RMU #define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2 -#elif defined(CONFIG_PPC_P2040) -#define CONFIG_MAX_CPUS 4 -#define CONFIG_SYS_FSL_NUM_CC_PLLS 2 -#define CONFIG_SYS_FSL_NUM_LAWS 32 -#define CONFIG_SYS_FSL_SEC_COMPAT 4 -#define CONFIG_SYS_NUM_FMAN 1 -#define CONFIG_SYS_NUM_FM1_DTSEC 5 -#define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_SYS_FM_MURAM_SIZE 0x28000 -#define CONFIG_SYS_FSL_TBCLK_DIV 32 -#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 -#define CONFIG_SYS_FSL_USB1_PHY_ENABLE -#define CONFIG_SYS_FSL_USB2_PHY_ENABLE -#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY -#define CONFIG_SYS_FSL_ERRATUM_ESDHC111 -#define CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011 -#define CONFIG_SYS_FSL_ERRATUM_CPU_A003999 -#define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 -#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 -#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 -#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 - -#elif defined(CONFIG_PPC_P2041) +#elif defined(CONFIG_PPC_P2041) /* also supports P2040 */ #define CONFIG_MAX_CPUS 4 #define CONFIG_SYS_FSL_NUM_CC_PLLS 2 #define CONFIG_SYS_FSL_NUM_LAWS 32 @@ -380,6 +334,10 @@ #define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 #define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 #define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 +#define CONFIG_SYS_FSL_ERRATUM_A004510 +#define CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV 0x10 +#define CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 0x11 +#define CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY 0xf0000000 #elif defined(CONFIG_PPC_P3041) #define CONFIG_MAX_CPUS 4 @@ -399,47 +357,18 @@ #define CONFIG_SYS_FSL_USB2_PHY_ENABLE #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 +#define CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011 #define CONFIG_SYS_FSL_ERRATUM_CPU_A003999 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 #define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 #define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 #define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 +#define CONFIG_SYS_FSL_ERRATUM_A004510 +#define CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV 0x10 +#define CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 0x11 +#define CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY 0xf0000000 -#elif defined(CONFIG_PPC_P3060) -#define CONFIG_MAX_CPUS 8 -#define CONFIG_SYS_FSL_NUM_CC_PLLS 4 -#define CONFIG_SYS_FSL_NUM_LAWS 32 -#define CONFIG_SYS_FSL_SEC_COMPAT 4 -#define CONFIG_SYS_NUM_FMAN 2 -#define CONFIG_SYS_NUM_FM1_DTSEC 4 -#define CONFIG_SYS_NUM_FM2_DTSEC 4 -#define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_SYS_FM_MURAM_SIZE 0x28000 -#define CONFIG_SYS_FSL_TBCLK_DIV 16 -#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 -#define CONFIG_SYS_FSL_ERRATUM_DDR_A003 -#define CONFIG_SYS_FSL_ERRATUM_CPU_A003999 -#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 -#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 -#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 - -#elif defined(CONFIG_PPC_P4040) -#define CONFIG_MAX_CPUS 4 -#define CONFIG_SYS_FSL_NUM_CC_PLLS 4 -#define CONFIG_SYS_FSL_NUM_LAWS 32 -#define CONFIG_SYS_FSL_SEC_COMPAT 4 -#define CONFIG_SYS_FM_MURAM_SIZE 0x28000 -#define CONFIG_SYS_FSL_TBCLK_DIV 16 -#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,p4080-pcie" -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 -#define CONFIG_SYS_FSL_ERRATUM_CPU_A003999 -#define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 -#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 -#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 -#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 - -#elif defined(CONFIG_PPC_P4080) +#elif defined(CONFIG_PPC_P4080) /* also supports P4040 */ #define CONFIG_MAX_CPUS 8 #define CONFIG_SYS_FSL_NUM_CC_PLLS 4 #define CONFIG_SYS_FSL_NUM_LAWS 32 @@ -474,32 +403,11 @@ #define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 #define CONFIG_SYS_FSL_RMU #define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2 +#define CONFIG_SYS_FSL_ERRATUM_A004510 +#define CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV 0x20 +#define CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY 0xff000000 -/* P5010 is single core version of P5020 */ -#elif defined(CONFIG_PPC_P5010) -#define CONFIG_MAX_CPUS 1 -#define CONFIG_SYS_FSL_NUM_CC_PLLS 2 -#define CONFIG_SYS_FSL_NUM_LAWS 32 -#define CONFIG_SYS_FSL_SEC_COMPAT 4 -#define CONFIG_FSL_SATA_V2 -#define CONFIG_SYS_NUM_FMAN 1 -#define CONFIG_SYS_NUM_FM1_DTSEC 5 -#define CONFIG_SYS_NUM_FM1_10GEC 1 -#define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_SYS_FM_MURAM_SIZE 0x28000 -#define CONFIG_SYS_FSL_TBCLK_DIV 32 -#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2" -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 -#define CONFIG_SYS_FSL_USB1_PHY_ENABLE -#define CONFIG_SYS_FSL_USB2_PHY_ENABLE -#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY -#define CONFIG_SYS_FSL_ERRATUM_ESDHC111 -#define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 -#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 -#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 -#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 - -#elif defined(CONFIG_PPC_P5020) +#elif defined(CONFIG_PPC_P5020) /* also supports P5010 */ #define CONFIG_MAX_CPUS 2 #define CONFIG_SYS_FSL_NUM_CC_PLLS 2 #define CONFIG_SYS_FSL_NUM_LAWS 32 @@ -521,6 +429,9 @@ #define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 #define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 #define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 +#define CONFIG_SYS_FSL_ERRATUM_A004510 +#define CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV 0x10 +#define CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY 0xc0000000 #elif defined(CONFIG_BSC9131) #define CONFIG_MAX_CPUS 1 diff --git a/arch/powerpc/include/asm/fsl_ddr_dimm_params.h b/arch/powerpc/include/asm/fsl_ddr_dimm_params.h index 982b809462..ffe4db8b8a 100644 --- a/arch/powerpc/include/asm/fsl_ddr_dimm_params.h +++ b/arch/powerpc/include/asm/fsl_ddr_dimm_params.h @@ -43,6 +43,7 @@ typedef struct dimm_params_s { /* DIMM timing parameters */ unsigned int mtb_ps; /* medium timebase ps, only for ddr3 */ + unsigned int ftb_10th_ps; /* fine timebase, in 1/10 ps, only for ddr3 */ unsigned int tAA_ps; /* minimum CAS latency time, only for ddr3 */ unsigned int tFAW_ps; /* four active window delay, only for ddr3 */ diff --git a/arch/powerpc/include/asm/fsl_ddr_sdram.h b/arch/powerpc/include/asm/fsl_ddr_sdram.h index 93639ba851..e271342f08 100644 --- a/arch/powerpc/include/asm/fsl_ddr_sdram.h +++ b/arch/powerpc/include/asm/fsl_ddr_sdram.h @@ -76,6 +76,13 @@ typedef ddr3_spd_eeprom_t generic_spd_eeprom_t; #define FSL_DDR_PAGE_INTERLEAVING 0x1 #define FSL_DDR_BANK_INTERLEAVING 0x2 #define FSL_DDR_SUPERBANK_INTERLEAVING 0x3 +#define FSL_DDR_3WAY_1KB_INTERLEAVING 0xA +#define FSL_DDR_3WAY_4KB_INTERLEAVING 0xC +#define FSL_DDR_3WAY_8KB_INTERLEAVING 0xD +/* placeholder for 4-way interleaving */ +#define FSL_DDR_4WAY_1KB_INTERLEAVING 0x1A +#define FSL_DDR_4WAY_4KB_INTERLEAVING 0x1C +#define FSL_DDR_4WAY_8KB_INTERLEAVING 0x1D /* DDR_SDRAM_CFG - DDR SDRAM Control Configuration */ @@ -88,6 +95,7 @@ typedef ddr3_spd_eeprom_t generic_spd_eeprom_t; #define SDRAM_CFG_SDRAM_TYPE_MASK 0x07000000 #define SDRAM_CFG_SDRAM_TYPE_SHIFT 24 #define SDRAM_CFG_DYN_PWR 0x00200000 +#define SDRAM_CFG_DBW_MASK 0x00180000 #define SDRAM_CFG_32_BE 0x00080000 #define SDRAM_CFG_16_BE 0x00100000 #define SDRAM_CFG_8_BE 0x00040000 diff --git a/arch/powerpc/include/asm/fsl_ifc.h b/arch/powerpc/include/asm/fsl_ifc.h index 7d95eb4416..ba41b73cc0 100644 --- a/arch/powerpc/include/asm/fsl_ifc.h +++ b/arch/powerpc/include/asm/fsl_ifc.h @@ -783,12 +783,16 @@ extern void init_early_memctl_regs(void); #define IFC_BASE_ADDR ((struct fsl_ifc *)CONFIG_SYS_IFC_ADDR) +#define get_ifc_cspr_ext(i) (in_be32(&(IFC_BASE_ADDR)->cspr_cs[i].cspr_ext)) #define get_ifc_cspr(i) (in_be32(&(IFC_BASE_ADDR)->cspr_cs[i].cspr)) +#define get_ifc_csor_ext(i) (in_be32(&(IFC_BASE_ADDR)->csor_cs[i].csor_ext)) #define get_ifc_csor(i) (in_be32(&(IFC_BASE_ADDR)->csor_cs[i].csor)) #define get_ifc_amask(i) (in_be32(&(IFC_BASE_ADDR)->amask_cs[i].amask)) #define get_ifc_ftim(i, j) (in_be32(&(IFC_BASE_ADDR)->ftim_cs[i].ftim[j])) +#define set_ifc_cspr_ext(i, v) (out_be32(&(IFC_BASE_ADDR)->cspr_cs[i].cspr_ext, v)) #define set_ifc_cspr(i, v) (out_be32(&(IFC_BASE_ADDR)->cspr_cs[i].cspr, v)) +#define set_ifc_csor_ext(i, v) (out_be32(&(IFC_BASE_ADDR)->csor_cs[i].csor_ext, v)) #define set_ifc_csor(i, v) (out_be32(&(IFC_BASE_ADDR)->csor_cs[i].csor, v)) #define set_ifc_amask(i, v) (out_be32(&(IFC_BASE_ADDR)->amask_cs[i].amask, v)) #define set_ifc_ftim(i, j, v) \ @@ -909,22 +913,24 @@ struct fsl_ifc_gpcm { */ struct fsl_ifc { u32 ifc_rev; - u32 res1[0x3]; + u32 res1[0x2]; struct { + u32 cspr_ext; u32 cspr; - u32 res2[0x2]; + u32 res2; } cspr_cs[FSL_IFC_BANK_COUNT]; - u32 res3[0x18]; + u32 res3[0x19]; struct { u32 amask; u32 res4[0x2]; } amask_cs[FSL_IFC_BANK_COUNT]; - u32 res5[0x18]; + u32 res5[0x17]; struct { + u32 csor_ext; u32 csor; - u32 res6[0x2]; + u32 res6; } csor_cs[FSL_IFC_BANK_COUNT]; - u32 res7[0x18]; + u32 res7[0x19]; struct { u32 ftim[4]; u32 res8[0x8]; diff --git a/arch/powerpc/include/asm/fsl_law.h b/arch/powerpc/include/asm/fsl_law.h index 13caffd96e..f9cec8ea44 100644 --- a/arch/powerpc/include/asm/fsl_law.h +++ b/arch/powerpc/include/asm/fsl_law.h @@ -60,14 +60,19 @@ enum law_trgt_if { LAW_TRGT_IF_DDR_1 = 0x10, LAW_TRGT_IF_DDR_2 = 0x11, /* 2nd controller */ + LAW_TRGT_IF_DDR_3 = 0x12, + LAW_TRGT_IF_DDR_4 = 0x13, LAW_TRGT_IF_DDR_INTRLV = 0x14, - + LAW_TRGT_IF_DDR_INTLV_34 = 0x15, + LAW_TRGT_IF_DDR_INTLV_123 = 0x17, + LAW_TRGT_IF_DDR_INTLV_1234 = 0x16, LAW_TRGT_IF_BMAN = 0x18, LAW_TRGT_IF_DCSR = 0x1d, LAW_TRGT_IF_LBC = 0x1f, LAW_TRGT_IF_QMAN = 0x3c, }; #define LAW_TRGT_IF_DDR LAW_TRGT_IF_DDR_1 +#define LAW_TRGT_IF_IFC LAW_TRGT_IF_LBC #else enum law_trgt_if { LAW_TRGT_IF_PCI = 0x00, @@ -86,6 +91,12 @@ enum law_trgt_if { LAW_TRGT_IF_DPAA_SWP_SRAM = 0x0e, LAW_TRGT_IF_DDR = 0x0f, LAW_TRGT_IF_DDR_2 = 0x16, /* 2nd controller */ + /* place holder for 3-way and 4-way interleaving */ + LAW_TRGT_IF_DDR_3, + LAW_TRGT_IF_DDR_4, + LAW_TRGT_IF_DDR_INTLV_34, + LAW_TRGT_IF_DDR_INTLV_123, + LAW_TRGT_IF_DDR_INTLV_1234, }; #define LAW_TRGT_IF_DDR_1 LAW_TRGT_IF_DDR #define LAW_TRGT_IF_PCI_1 LAW_TRGT_IF_PCI diff --git a/arch/powerpc/include/asm/fsl_serdes.h b/arch/powerpc/include/asm/fsl_serdes.h index 0f31af1db3..22525f1156 100644 --- a/arch/powerpc/include/asm/fsl_serdes.h +++ b/arch/powerpc/include/asm/fsl_serdes.h @@ -41,6 +41,7 @@ enum srds_prtcl { SGMII_FM2_DTSEC2, SGMII_FM2_DTSEC3, SGMII_FM2_DTSEC4, + SGMII_FM2_DTSEC5, SGMII_TSEC1, SGMII_TSEC2, SGMII_TSEC3, diff --git a/arch/powerpc/include/asm/fsl_srio.h b/arch/powerpc/include/asm/fsl_srio.h index a905a266c4..dfd8e08f3e 100644 --- a/arch/powerpc/include/asm/fsl_srio.h +++ b/arch/powerpc/include/asm/fsl_srio.h @@ -55,10 +55,8 @@ enum atmu_size { #define atmu_size_bytes(x) (1ULL << ((x & 0x3f) + 1)) extern void srio_init(void); -#ifdef CONFIG_SRIOBOOT_MASTER -extern void srio_boot_master(void); -#ifdef CONFIG_SRIOBOOT_SLAVE_HOLDOFF -extern void srio_boot_master_release_slave(void); -#endif +#ifdef CONFIG_FSL_CORENET +extern void srio_boot_master(int port); +extern void srio_boot_master_release_slave(int port); #endif #endif diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index 53d563ed0a..7de33a7dde 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -1729,6 +1729,7 @@ typedef struct ccsr_gur { #define FSL_CORENET_DEVDISR2_DTSEC2_2 0x00004000 #define FSL_CORENET_DEVDISR2_DTSEC2_3 0x00002000 #define FSL_CORENET_DEVDISR2_DTSEC2_4 0x00001000 +#define FSL_CORENET_DEVDISR2_DTSEC2_5 0x00000800 #define FSL_CORENET_NUM_DEVDISR 2 u8 res7[8]; u32 powmgtcsr; /* Power management status & control */ @@ -1758,13 +1759,14 @@ typedef struct ccsr_gur { #define FSL_CORENET_RCWSR5_DDR_SYNC 0x00000080 #define FSL_CORENET_RCWSR5_DDR_SYNC_SHIFT 7 #define FSL_CORENET_RCWSR5_SRDS_EN 0x00002000 +#define FSL_CORENET_RCWSR6_BOOT_LOC 0x0f800000 #define FSL_CORENET_RCWSRn_SRDS_LPD_B2 0x3c000000 /* bits 162..165 */ #define FSL_CORENET_RCWSRn_SRDS_LPD_B3 0x003c0000 /* bits 170..173 */ #define FSL_CORENET_RCWSR7_MCK_TO_PLAT_RAT 0x00400000 #define FSL_CORENET_RCWSR8_HOST_AGT_B1 0x00e00000 #define FSL_CORENET_RCWSR8_HOST_AGT_B2 0x00100000 #define FSL_CORENET_RCWSR11_EC1 0x00c00000 /* bits 360..361 */ -#if defined(CONFIG_PPC_P4080) || defined(CONFIG_PPC_P3060) +#ifdef CONFIG_PPC_P4080 #define FSL_CORENET_RCWSR11_EC1_FM1_DTSEC1 0x00000000 #define FSL_CORENET_RCWSR11_EC1_FM1_USB1 0x00800000 #define FSL_CORENET_RCWSR11_EC2 0x001c0000 /* bits 363..365 */ @@ -1772,7 +1774,7 @@ typedef struct ccsr_gur { #define FSL_CORENET_RCWSR11_EC2_FM1_DTSEC2 0x00080000 #define FSL_CORENET_RCWSR11_EC2_USB2 0x00100000 #endif -#if defined(CONFIG_PPC_P2040) || defined(CONFIG_PPC_P2041) \ +#if defined(CONFIG_PPC_P2041) \ || defined(CONFIG_PPC_P3041) || defined(CONFIG_PPC_P5020) #define FSL_CORENET_RCWSR11_EC1_FM1_DTSEC4_RGMII 0x00000000 #define FSL_CORENET_RCWSR11_EC1_FM1_DTSEC4_MII 0x00800000 @@ -1836,7 +1838,13 @@ typedef struct ccsr_gur { u8 res31[184]; u32 sriopstecr; /* SRIO prescaler timer enable control */ u32 dcsrcr; /* DCSR Control register */ - u8 res32[1784]; + u8 res31a[56]; + u32 tp_ityp[64]; /* Topology Initiator Type Register */ + struct { + u32 upper; + u32 lower; + } tp_cluster[16]; /* Core Cluster n Topology Register */ + u8 res32[1344]; u32 pmuxcr; /* Pin multiplexing control */ u8 res33[60]; u32 iovselsr; /* I/O voltage selection status */ @@ -1849,6 +1857,18 @@ typedef struct ccsr_gur { u8 res37[380]; } ccsr_gur_t; +#define TP_ITYP_AV 0x00000001 /* Initiator available */ +#define TP_ITYP_TYPE(x) (((x) & 0x6) >> 1) /* Initiator Type */ +#define TP_ITYP_TYPE_OTHER 0x0 +#define TP_ITYP_TYPE_PPC 0x1 /* PowerPC */ +#define TP_ITYP_TYPE_SC 0x2 /* StarCore DSP */ +#define TP_ITYP_TYPE_HA 0x3 /* HW Accelerator */ +#define TP_ITYP_THDS(x) (((x) & 0x18) >> 3) /* # threads */ +#define TP_ITYP_VER(x) (((x) & 0xe0) >> 5) /* Initiator Version */ + +#define TP_CLUSTER_EOC 0x80000000 /* end of clusters */ +#define TP_CLUSTER_INIT_MASK 0x0000003f /* initiator mask */ + #define FSL_CORENET_DCSR_SZ_MASK 0x00000003 #define FSL_CORENET_DCSR_SZ_4M 0x0 #define FSL_CORENET_DCSR_SZ_1G 0x3 @@ -1890,6 +1910,73 @@ typedef struct ccsr_clk { u8 res15[0x3dc]; } ccsr_clk_t; +#ifdef CONFIG_SYS_FSL_QORIQ_CHASSIS2 +typedef struct ccsr_rcpm { + u8 res_00[12]; + u32 tph10sr0; /* Thread PH10 Status Register */ + u8 res_10[12]; + u32 tph10setr0; /* Thread PH10 Set Control Register */ + u8 res_20[12]; + u32 tph10clrr0; /* Thread PH10 Clear Control Register */ + u8 res_30[12]; + u32 tph10psr0; /* Thread PH10 Previous Status Register */ + u8 res_40[12]; + u32 twaitsr0; /* Thread Wait Status Register */ + u8 res_50[96]; + u32 pcph15sr; /* Physical Core PH15 Status Register */ + u32 pcph15setr; /* Physical Core PH15 Set Control Register */ + u32 pcph15clrr; /* Physical Core PH15 Clear Control Register */ + u32 pcph15psr; /* Physical Core PH15 Prev Status Register */ + u8 res_c0[16]; + u32 pcph20sr; /* Physical Core PH20 Status Register */ + u32 pcph20setr; /* Physical Core PH20 Set Control Register */ + u32 pcph20clrr; /* Physical Core PH20 Clear Control Register */ + u32 pcph20psr; /* Physical Core PH20 Prev Status Register */ + u32 pcpw20sr; /* Physical Core PW20 Status Register */ + u8 res_e0[12]; + u32 pcph30sr; /* Physical Core PH30 Status Register */ + u32 pcph30setr; /* Physical Core PH30 Set Control Register */ + u32 pcph30clrr; /* Physical Core PH30 Clear Control Register */ + u32 pcph30psr; /* Physical Core PH30 Prev Status Register */ + u8 res_100[32]; + u32 ippwrgatecr; /* IP Power Gating Control Register */ + u8 res_124[12]; + u32 powmgtcsr; /* Power Management Control & Status Reg */ + u8 res_134[12]; + u32 ippdexpcr[4]; /* IP Powerdown Exception Control Reg */ + u8 res_150[12]; + u32 tpmimr0; /* Thread PM Interrupt Mask Reg */ + u8 res_160[12]; + u32 tpmcimr0; /* Thread PM Crit Interrupt Mask Reg */ + u8 res_170[12]; + u32 tpmmcmr0; /* Thread PM Machine Check Interrupt Mask Reg */ + u8 res_180[12]; + u32 tpmnmimr0; /* Thread PM NMI Mask Reg */ + u8 res_190[12]; + u32 tmcpmaskcr0; /* Thread Machine Check Mask Control Reg */ + u32 pctbenr; /* Physical Core Time Base Enable Reg */ + u32 pctbclkselr; /* Physical Core Time Base Clock Select */ + u32 tbclkdivr; /* Time Base Clock Divider Register */ + u8 res_1ac[4]; + u32 ttbhltcr[4]; /* Thread Time Base Halt Control Register */ + u32 clpcl10sr; /* Cluster PCL10 Status Register */ + u32 clpcl10setr; /* Cluster PCL30 Set Control Register */ + u32 clpcl10clrr; /* Cluster PCL30 Clear Control Register */ + u32 clpcl10psr; /* Cluster PCL30 Prev Status Register */ + u32 cddslpsetr; /* Core Domain Deep Sleep Set Register */ + u32 cddslpclrr; /* Core Domain Deep Sleep Clear Register */ + u32 cdpwroksetr; /* Core Domain Power OK Set Register */ + u32 cdpwrokclrr; /* Core Domain Power OK Clear Register */ + u32 cdpwrensr; /* Core Domain Power Enable Status Register */ + u32 cddslsr; /* Core Domain Deep Sleep Status Register */ + u8 res_1e8[8]; + u32 dslpcntcr[8]; /* Deep Sleep Counter Cfg Register */ + u8 res_300[3568]; +} ccsr_rcpm_t; + +#define ctbenrl pctbenr + +#else typedef struct ccsr_rcpm { u8 res1[4]; u32 cdozsrl; /* Core Doze Status */ @@ -1926,6 +2013,7 @@ typedef struct ccsr_rcpm { u32 ctbhltcrl; /* Core Time Base Halt Control */ u8 res18[0xf68]; } ccsr_rcpm_t; +#endif /* CONFIG_SYS_FSL_QORIQ_CHASSIS2 */ #else typedef struct ccsr_gur { @@ -2259,8 +2347,7 @@ typedef struct ccsr_gur { u8 res11a[76]; par_io_t qe_par_io[7]; u8 res11b[1600]; -#elif defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ - defined(CONFIG_P1021) || defined(CONFIG_P1025) +#elif defined(CONFIG_P1012) || defined(CONFIG_P1021) || defined(CONFIG_P1025) u8 res11a[12]; u32 iovselsr; u8 res11b[60]; @@ -2534,6 +2621,7 @@ struct ccsr_rman { #define CONFIG_SYS_FSL_CORENET_CCM_OFFSET 0x0000 #define CONFIG_SYS_MPC85xx_DDR_OFFSET 0x8000 #define CONFIG_SYS_MPC85xx_DDR2_OFFSET 0x9000 +#define CONFIG_SYS_MPC85xx_DDR3_OFFSET 0xA000 #define CONFIG_SYS_FSL_CORENET_CLK_OFFSET 0xE1000 #define CONFIG_SYS_FSL_CORENET_RCPM_OFFSET 0xE2000 #define CONFIG_SYS_FSL_CORENET_SERDES_OFFSET 0xEA000 @@ -2544,6 +2632,7 @@ struct ccsr_rman { #define CONFIG_SYS_MPC85xx_ESPI_OFFSET 0x110000 #define CONFIG_SYS_MPC85xx_ESDHC_OFFSET 0x114000 #define CONFIG_SYS_MPC85xx_LBC_OFFSET 0x124000 +#define CONFIG_SYS_MPC85xx_IFC_OFFSET 0x124000 #define CONFIG_SYS_MPC85xx_GPIO_OFFSET 0x130000 #define CONFIG_SYS_FSL_CORENET_RMAN_OFFSET 0x1e0000 #define CONFIG_SYS_MPC85xx_PCIE1_OFFSET 0x200000 @@ -2652,6 +2741,8 @@ struct ccsr_rman { (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_DDR_OFFSET) #define CONFIG_SYS_MPC85xx_DDR2_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_DDR2_OFFSET) +#define CONFIG_SYS_MPC85xx_DDR3_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_DDR3_OFFSET) #define CONFIG_SYS_LBC_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_LBC_OFFSET) #define CONFIG_SYS_IFC_ADDR \ diff --git a/arch/powerpc/include/asm/io.h b/arch/powerpc/include/asm/io.h index ec0bfaee99..9e208618d9 100644 --- a/arch/powerpc/include/asm/io.h +++ b/arch/powerpc/include/asm/io.h @@ -162,7 +162,7 @@ static inline void __raw_writel(unsigned int v, volatile void __iomem *addr) * is actually performed (i.e. the data has come back) before we start * executing any following instructions. */ -static inline u8 in_8(const volatile unsigned char __iomem *addr) +extern inline u8 in_8(const volatile unsigned char __iomem *addr) { u8 ret; @@ -173,7 +173,7 @@ static inline u8 in_8(const volatile unsigned char __iomem *addr) return ret; } -static inline void out_8(volatile unsigned char __iomem *addr, u8 val) +extern inline void out_8(volatile unsigned char __iomem *addr, u8 val) { __asm__ __volatile__("sync;\n" "stb%U0%X0 %1,%0;\n" @@ -181,7 +181,7 @@ static inline void out_8(volatile unsigned char __iomem *addr, u8 val) : "r" (val)); } -static inline u16 in_le16(const volatile unsigned short __iomem *addr) +extern inline u16 in_le16(const volatile unsigned short __iomem *addr) { u16 ret; @@ -192,7 +192,7 @@ static inline u16 in_le16(const volatile unsigned short __iomem *addr) return ret; } -static inline u16 in_be16(const volatile unsigned short __iomem *addr) +extern inline u16 in_be16(const volatile unsigned short __iomem *addr) { u16 ret; @@ -202,18 +202,18 @@ static inline u16 in_be16(const volatile unsigned short __iomem *addr) return ret; } -static inline void out_le16(volatile unsigned short __iomem *addr, u16 val) +extern inline void out_le16(volatile unsigned short __iomem *addr, u16 val) { __asm__ __volatile__("sync; sthbrx %1,0,%2" : "=m" (*addr) : "r" (val), "r" (addr)); } -static inline void out_be16(volatile unsigned short __iomem *addr, u16 val) +extern inline void out_be16(volatile unsigned short __iomem *addr, u16 val) { __asm__ __volatile__("sync; sth%U0%X0 %1,%0" : "=m" (*addr) : "r" (val)); } -static inline u32 in_le32(const volatile unsigned __iomem *addr) +extern inline u32 in_le32(const volatile unsigned __iomem *addr) { u32 ret; @@ -224,7 +224,7 @@ static inline u32 in_le32(const volatile unsigned __iomem *addr) return ret; } -static inline u32 in_be32(const volatile unsigned __iomem *addr) +extern inline u32 in_be32(const volatile unsigned __iomem *addr) { u32 ret; @@ -234,13 +234,13 @@ static inline u32 in_be32(const volatile unsigned __iomem *addr) return ret; } -static inline void out_le32(volatile unsigned __iomem *addr, u32 val) +extern inline void out_le32(volatile unsigned __iomem *addr, u32 val) { __asm__ __volatile__("sync; stwbrx %1,0,%2" : "=m" (*addr) : "r" (val), "r" (addr)); } -static inline void out_be32(volatile unsigned __iomem *addr, u32 val) +extern inline void out_be32(volatile unsigned __iomem *addr, u32 val) { __asm__ __volatile__("sync; stw%U0%X0 %1,%0" : "=m" (*addr) : "r" (val)); } diff --git a/arch/powerpc/include/asm/mmu.h b/arch/powerpc/include/asm/mmu.h index 209103e3ce..2e0e292da0 100644 --- a/arch/powerpc/include/asm/mmu.h +++ b/arch/powerpc/include/asm/mmu.h @@ -475,6 +475,10 @@ extern void print_bats(void); #define BOOKE_PAGESZ_256GB 14 #define BOOKE_PAGESZ_1TB 15 +#define TLBIVAX_ALL 4 +#define TLBIVAX_TLB0 0 +#define TLBIVAX_TLB1 8 + #ifdef CONFIG_E500 #ifndef __ASSEMBLY__ extern void set_tlb(u8 tlb, u32 epn, u64 rpn, diff --git a/arch/powerpc/include/asm/mp.h b/arch/powerpc/include/asm/mp.h index 3ffa30b978..fe490bac05 100644 --- a/arch/powerpc/include/asm/mp.h +++ b/arch/powerpc/include/asm/mp.h @@ -28,4 +28,10 @@ void cpu_mp_lmb_reserve(struct lmb *lmb); u32 determine_mp_bootpg(void); int is_core_disabled(int nr); +#ifdef CONFIG_E6500 +#define thread_to_core(x) (x >> 1) +#else +#define thread_to_core(x) (x) +#endif + #endif diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h index dc009d6604..36695e2fb6 100644 --- a/arch/powerpc/include/asm/processor.h +++ b/arch/powerpc/include/asm/processor.h @@ -486,11 +486,13 @@ #define SPRN_L2CFG0 0x207 /* L2 Cache Configuration Register 0 */ #define SPRN_L1CSR0 0x3f2 /* L1 Data Cache Control and Status Register 0 */ #define L1CSR0_CPE 0x00010000 /* Data Cache Parity Enable */ +#define L1CSR0_CUL 0x00000400 /* (D-)Cache Unable to Lock */ #define L1CSR0_DCLFR 0x00000100 /* D-Cache Lock Flash Reset */ #define L1CSR0_DCFI 0x00000002 /* Data Cache Flash Invalidate */ #define L1CSR0_DCE 0x00000001 /* Data Cache Enable */ #define SPRN_L1CSR1 0x3f3 /* L1 Instruction Cache Control and Status Register 1 */ #define L1CSR1_CPE 0x00010000 /* Instruction Cache Parity Enable */ +#define L1CSR1_ICUL 0x00000400 /* I-Cache Unable to Lock */ #define L1CSR1_ICLFR 0x00000100 /* I-Cache Lock Flash Reset */ #define L1CSR1_ICFI 0x00000002 /* Instruction Cache Flash Invalidate */ #define L1CSR1_ICE 0x00000001 /* Instruction Cache Enable */ @@ -513,6 +515,7 @@ #define SPRN_TLB0CFG 0x2B0 /* TLB 0 Config Register */ #define SPRN_TLB1CFG 0x2B1 /* TLB 1 Config Register */ +#define TLBnCFG_NENTRY_MASK 0x00000fff #define SPRN_TLB0PS 0x158 /* TLB 0 Page Size Register */ #define SPRN_TLB1PS 0x159 /* TLB 1 Page Size Register */ #define SPRN_MMUCSR0 0x3f4 /* MMU control and status register 0 */ @@ -948,6 +951,7 @@ #define PVR_VER_E500_V2 0x8021 #define PVR_VER_E500MC 0x8023 #define PVR_VER_E5500 0x8024 +#define PVR_VER_E6500 0x8040 #define PVR_86xx 0x80040000 @@ -1075,8 +1079,6 @@ #define SVR_P1012 0x80E501 #define SVR_P1013 0x80E700 #define SVR_P1014 0x80F101 -#define SVR_P1015 0x80E502 -#define SVR_P1016 0x80E503 #define SVR_P1017 0x80F700 #define SVR_P1020 0x80E400 #define SVR_P1021 0x80E401 @@ -1089,7 +1091,6 @@ #define SVR_P2040 0x821000 #define SVR_P2041 0x821001 #define SVR_P3041 0x821103 -#define SVR_P3060 0x820002 #define SVR_P4040 0x820100 #define SVR_P4080 0x820000 #define SVR_P5010 0x822100 @@ -1158,6 +1159,7 @@ struct cpu_type { }; struct cpu_type *identify_cpu(u32 ver); +int fixup_cpu(void); #if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) #define CPU_TYPE_ENTRY(n, v, nc) \ diff --git a/arch/powerpc/lib/board.c b/arch/powerpc/lib/board.c index fea310eedd..07feaf55fc 100644 --- a/arch/powerpc/lib/board.c +++ b/arch/powerpc/lib/board.c @@ -345,6 +345,13 @@ ulong get_effective_memsize(void) #endif } +int __fixup_cpu(void) +{ + return 0; +} + +int fixup_cpu(void) __attribute__((weak, alias("__fixup_cpu"))); + /* * This is the first part of the initialization sequence that is * implemented in C, but still running from ROM. @@ -521,9 +528,8 @@ void board_init_f(ulong bootflag) addr_sp -= 16; addr_sp &= ~0xF; s = (ulong *) addr_sp; - *s-- = 0; - *s-- = 0; - addr_sp = (ulong) s; + *s = 0; /* Terminate back chain */ + *++s = 0; /* NULL return address */ debug("Stack Pointer at: %08lx\n", addr_sp); /* @@ -647,6 +653,12 @@ void board_init_r(gd_t *id, ulong dest_addr) * We need to update it to point to the same CPU entry in RAM. */ gd->cpu += dest_addr - CONFIG_SYS_MONITOR_BASE; + + /* + * If we didn't know the cpu mask & # cores, we can save them of + * now rather than 'computing' them constantly + */ + fixup_cpu(); #endif #ifdef CONFIG_SYS_EXTRA_ENV_RELOC diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index 0b40dc7bf7..54cb098a91 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -51,14 +51,12 @@ COBJS-$(CONFIG_MPC8572DS) += ics307_clk.o COBJS-$(CONFIG_P1022DS) += ics307_clk.o COBJS-$(CONFIG_P2020DS) += ics307_clk.o COBJS-$(CONFIG_P3041DS) += ics307_clk.o -COBJS-$(CONFIG_P3060QDS) += ics307_clk.o COBJS-$(CONFIG_P4080DS) += ics307_clk.o COBJS-$(CONFIG_P5020DS) += ics307_clk.o # deal with common files for P-series corenet based devices SUBLIB-$(CONFIG_P2041RDB) += p_corenet/libp_corenet.o SUBLIB-$(CONFIG_P3041DS) += p_corenet/libp_corenet.o -SUBLIB-$(CONFIG_P3060QDS) += p_corenet/libp_corenet.o SUBLIB-$(CONFIG_P4080DS) += p_corenet/libp_corenet.o SUBLIB-$(CONFIG_P5020DS) += p_corenet/libp_corenet.o diff --git a/board/freescale/common/fman.c b/board/freescale/common/fman.c index 6ddf816201..3ef49369a4 100644 --- a/board/freescale/common/fman.c +++ b/board/freescale/common/fman.c @@ -25,6 +25,9 @@ #include <libfdt_env.h> #include <fdt_support.h> +#include <fm_eth.h> +#include <asm/fsl_serdes.h> + /* * Given the following ... * @@ -67,3 +70,31 @@ int fdt_set_phy_handle(void *fdt, char *compat, phys_addr_t addr, return fdt_setprop(fdt, offset, "phy-handle", &ph, sizeof(ph)); } + +/* + * Return the SerDes device enum for a given Fman port + * + * This function just maps the fm_port namespace to the srds_prtcl namespace. + */ +enum srds_prtcl serdes_device_from_fm_port(enum fm_port port) +{ + static const enum srds_prtcl srds_table[] = { + [FM1_DTSEC1] = SGMII_FM1_DTSEC1, + [FM1_DTSEC2] = SGMII_FM1_DTSEC2, + [FM1_DTSEC3] = SGMII_FM1_DTSEC3, + [FM1_DTSEC4] = SGMII_FM1_DTSEC4, + [FM1_DTSEC5] = SGMII_FM1_DTSEC5, + [FM1_10GEC1] = XAUI_FM1, + [FM2_DTSEC1] = SGMII_FM2_DTSEC1, + [FM2_DTSEC2] = SGMII_FM2_DTSEC2, + [FM2_DTSEC3] = SGMII_FM2_DTSEC3, + [FM2_DTSEC4] = SGMII_FM2_DTSEC4, + [FM2_DTSEC5] = SGMII_FM2_DTSEC5, + [FM2_10GEC1] = XAUI_FM2, + }; + + if ((port < FM1_DTSEC1) || (port > FM2_10GEC1)) + return NONE; + else + return srds_table[port]; +} diff --git a/board/freescale/common/fman.h b/board/freescale/common/fman.h index d39ef080c1..734b1da1d6 100644 --- a/board/freescale/common/fman.h +++ b/board/freescale/common/fman.h @@ -23,4 +23,6 @@ int fdt_set_phy_handle(void *fdt, char *compat, phys_addr_t addr, const char *alias); +enum srds_prtcl serdes_device_from_fm_port(enum fm_port port); + #endif diff --git a/board/freescale/common/p_corenet/law.c b/board/freescale/common/p_corenet/law.c index c4566ddd4f..09ef5615d2 100644 --- a/board/freescale/common/p_corenet/law.c +++ b/board/freescale/common/p_corenet/law.c @@ -48,19 +48,6 @@ struct law_entry law_table[] = { #ifdef CONFIG_SYS_NAND_BASE_PHYS SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC), #endif -#ifdef CONFIG_SRIOBOOT_SLAVE -#if defined(CONFIG_SRIOBOOT_SLAVE_PORT0) - SET_LAW(CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS, - LAW_SIZE_1M, LAW_TRGT_IF_RIO_1), - SET_LAW(CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS, - LAW_SIZE_1M, LAW_TRGT_IF_RIO_1), -#elif defined(CONFIG_SRIOBOOT_SLAVE_PORT1) - SET_LAW(CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS, - LAW_SIZE_1M, LAW_TRGT_IF_RIO_2), - SET_LAW(CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS, - LAW_SIZE_1M, LAW_TRGT_IF_RIO_2), -#endif -#endif }; int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/common/p_corenet/tlb.c b/board/freescale/common/p_corenet/tlb.c index da2162728f..e5cf208a90 100644 --- a/board/freescale/common/p_corenet/tlb.c +++ b/board/freescale/common/p_corenet/tlb.c @@ -66,13 +66,13 @@ struct fsl_e_tlb_entry tlb_table[] = { SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 0, BOOKE_PAGESZ_1M, 1), -#elif defined(CONFIG_SRIOBOOT_SLAVE) +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) /* - * SRIOBOOT-SLAVE. When slave boot, the address of the + * SRIO_PCIE_BOOT-SLAVE. When slave boot, the address of the * space is at 0xfff00000, it covered the 0xfffff000. */ - SET_TLB_ENTRY(1, CONFIG_SYS_SRIOBOOT_SLAVE_ADDR, - CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS, + SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR, + CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, 0, 0, BOOKE_PAGESZ_1M, 1), #else @@ -147,13 +147,13 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 16, BOOKE_PAGESZ_1M, 1), #endif -#ifdef CONFIG_SRIOBOOT_SLAVE +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE /* - * SRIOBOOT-SLAVE. 1M space from 0xffe00000 for fetching ucode - * and ENV from master + * SRIO_PCIE_BOOT-SLAVE. 1M space from 0xffe00000 for + * fetching ucode and ENV from master */ - SET_TLB_ENTRY(1, CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR, - CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS, + SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR, + CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, 0, 17, BOOKE_PAGESZ_1M, 1), #endif diff --git a/board/freescale/corenet_ds/eth_p4080.c b/board/freescale/corenet_ds/eth_p4080.c index b87b0922ac..2c69c516dd 100644 --- a/board/freescale/corenet_ds/eth_p4080.c +++ b/board/freescale/corenet_ds/eth_p4080.c @@ -68,6 +68,15 @@ static char *mdio_names[16] = { NULL, NULL, NULL, }; +/* + * Mapping of all 18 SERDES lanes to board slots. A value of '0' here means + * that the mapping must be determined dynamically, or that the lane maps to + * something other than a board slot. + */ +static u8 lane_to_slot[] = { + 1, 1, 2, 2, 3, 3, 3, 3, 6, 6, 4, 4, 4, 4, 5, 5, 5, 5 +}; + static char *p4080ds_mdio_name_for_muxval(u32 muxval) { return mdio_names[(muxval & EMI_MASK) >> 28]; @@ -290,15 +299,6 @@ void fdt_fixup_board_enet(void *fdt) } } -enum board_slots { - SLOT1 = 1, - SLOT2, - SLOT3, - SLOT4, - SLOT5, - SLOT6, -}; - int board_eth_init(bd_t *bis) { #ifdef CONFIG_FMAN_ENET @@ -307,27 +307,6 @@ int board_eth_init(bd_t *bis) struct fsl_pq_mdio_info dtsec_mdio_info; struct tgec_mdio_info tgec_mdio_info; - u8 lane_to_slot[] = { - SLOT1, /* 0 - Bank 1:A */ - SLOT1, /* 1 - Bank 1:B */ - SLOT2, /* 2 - Bank 1:C */ - SLOT2, /* 3 - Bank 1:D */ - SLOT3, /* 4 - Bank 1:E */ - SLOT3, /* 5 - Bank 1:F */ - SLOT3, /* 6 - Bank 1:G */ - SLOT3, /* 7 - Bank 1:H */ - SLOT6, /* 8 - Bank 1:I */ - SLOT6, /* 9 - Bank 1:J */ - SLOT4, /* 10 - Bank 2:A */ - SLOT4, /* 11 - Bank 2:B */ - SLOT4, /* 12 - Bank 2:C */ - SLOT4, /* 13 - Bank 2:D */ - SLOT5, /* 14 - Bank 3:A */ - SLOT5, /* 15 - Bank 3:B */ - SLOT5, /* 16 - Bank 3:C */ - SLOT5, /* 17 - Bank 3:D */ - }; - /* Initialize the mdio_mux array so we can recognize empty elements */ for (i = 0; i < NUM_FM_PORTS; i++) mdio_mux[i] = EMI_NONE; @@ -380,17 +359,17 @@ int board_eth_init(bd_t *bis) break; slot = lane_to_slot[lane]; switch (slot) { - case SLOT3: + case 3: mdio_mux[i] = EMI1_SLOT3; fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); break; - case SLOT4: + case 4: mdio_mux[i] = EMI1_SLOT4; fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); break; - case SLOT5: + case 5: mdio_mux[i] = EMI1_SLOT5; fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); @@ -417,12 +396,12 @@ int board_eth_init(bd_t *bis) break; slot = lane_to_slot[lane]; switch (slot) { - case SLOT4: + case 4: mdio_mux[i] = EMI2_SLOT4; fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); break; - case SLOT5: + case 5: mdio_mux[i] = EMI2_SLOT5; fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); @@ -444,17 +423,17 @@ int board_eth_init(bd_t *bis) break; slot = lane_to_slot[lane]; switch (slot) { - case SLOT3: + case 3: mdio_mux[i] = EMI1_SLOT3; fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); break; - case SLOT4: + case 4: mdio_mux[i] = EMI1_SLOT4; fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); break; - case SLOT5: + case 5: mdio_mux[i] = EMI1_SLOT5; fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); @@ -481,12 +460,12 @@ int board_eth_init(bd_t *bis) break; slot = lane_to_slot[lane]; switch (slot) { - case SLOT4: + case 4: mdio_mux[i] = EMI2_SLOT4; fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); break; - case SLOT5: + case 5: mdio_mux[i] = EMI2_SLOT5; fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); diff --git a/board/freescale/corenet_ds/pbi.cfg b/board/freescale/corenet_ds/pbi.cfg new file mode 100644 index 0000000000..50806ca8a0 --- /dev/null +++ b/board/freescale/corenet_ds/pbi.cfg @@ -0,0 +1,51 @@ +# +# Copyright 2012 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# +# Refer docs/README.pblimage for more details about how-to configure +# and create PBL boot image +# + +#PBI commands +#Initialize CPC1 as 1MB SRAM +09010000 00200400 +09138000 00000000 +091380c0 00000100 +09010100 00000000 +09010104 fff0000b +09010f00 08000000 +09010000 80000000 +#Configure LAW for CPC1 +09000d00 00000000 +09000d04 fff00000 +09000d08 81000013 +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Initialize eSPI controller, default configuration is slow for eSPI to +#load data, this configuration comes from u-boot eSPI driver. +09110000 80000403 +09110020 2d170008 +09110024 00100008 +09110028 00100008 +0911002c 00100008 +#Flush PBL data +09138000 00000000 +091380c0 00000000 diff --git a/board/freescale/corenet_ds/rcw_p3041ds.cfg b/board/freescale/corenet_ds/rcw_p3041ds.cfg new file mode 100644 index 0000000000..8813156219 --- /dev/null +++ b/board/freescale/corenet_ds/rcw_p3041ds.cfg @@ -0,0 +1,11 @@ +# +# Default RCW for P3041DS. +# + +#PBL preamble and RCW header +aa55aa55 010e0100 +#64 bytes RCW data +12600000 00000000 241C0000 00000000 +D8984A01 03002000 58000000 41000000 +00000000 00000000 00000000 10070000 +00000000 00000000 00000000 00000000 diff --git a/board/freescale/corenet_ds/rcw_p4080ds.cfg b/board/freescale/corenet_ds/rcw_p4080ds.cfg new file mode 100644 index 0000000000..6a26339599 --- /dev/null +++ b/board/freescale/corenet_ds/rcw_p4080ds.cfg @@ -0,0 +1,11 @@ +# +# Default RCW for P4080DS. +# + +#PBL preamble and RCW header +aa55aa55 010e0100 +#64 bytes RCW data +105a0000 00000000 1e1e181e 0000cccc +58400000 3c3c2000 58000000 e1000000 +00000000 00000000 00000000 008b6000 +00000000 00000000 00000000 00000000 diff --git a/board/freescale/corenet_ds/rcw_p5020ds.cfg b/board/freescale/corenet_ds/rcw_p5020ds.cfg new file mode 100644 index 0000000000..b09e409bbf --- /dev/null +++ b/board/freescale/corenet_ds/rcw_p5020ds.cfg @@ -0,0 +1,11 @@ +# +# Default RCW for P5020DS. +# + +#PBL preamble and RCW header +aa55aa55 010e0100 +#64 bytes RCW data +0C540000 00000000 1E120000 00000000 +D8984A01 03002000 58000000 41000000 +00000000 00000000 00000000 10070000 +00000000 00000000 00000000 00000000 diff --git a/board/freescale/mpc8540ads/mpc8540ads.c b/board/freescale/mpc8540ads/mpc8540ads.c index c75585e28c..a275d3a074 100644 --- a/board/freescale/mpc8540ads/mpc8540ads.c +++ b/board/freescale/mpc8540ads/mpc8540ads.c @@ -87,10 +87,10 @@ local_bus_init(void) lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { - lbc->lcrr = CONFIG_SYS_LBC_LCRR | 0x80000000; /* DLL Bypass */ + lbc->lcrr = CONFIG_SYS_LBC_LCRR | LCRR_DBYP; /* DLL Bypass */ } else if (lbc_hz >= 133) { - lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000); /* DLL Enabled */ + lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~LCRR_DBYP); /* DLL Enabled */ } else { /* @@ -105,7 +105,7 @@ local_bus_init(void) lbc->lcrr = 0x10000004; } - lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000); /* DLL Enabled */ + lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~LCRR_DBYP); /* DLL Enabled */ udelay(200); /* diff --git a/board/freescale/mpc8541cds/mpc8541cds.c b/board/freescale/mpc8541cds/mpc8541cds.c index 532d32ac7c..13ca84b652 100644 --- a/board/freescale/mpc8541cds/mpc8541cds.c +++ b/board/freescale/mpc8541cds/mpc8541cds.c @@ -269,13 +269,13 @@ local_bus_init(void) lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { - lbc->lcrr |= 0x80000000; /* DLL Bypass */ + lbc->lcrr |= LCRR_DBYP; /* DLL Bypass */ } else if (lbc_hz >= 133) { - lbc->lcrr &= (~0x80000000); /* DLL Enabled */ + lbc->lcrr &= (~LCRR_DBYP); /* DLL Enabled */ } else { - lbc->lcrr &= (~0x80000000); /* DLL Enabled */ + lbc->lcrr &= (~LCRR_DBYP); /* DLL Enabled */ udelay(200); /* diff --git a/board/freescale/mpc8555cds/mpc8555cds.c b/board/freescale/mpc8555cds/mpc8555cds.c index 3361614de5..4cfd61cdd9 100644 --- a/board/freescale/mpc8555cds/mpc8555cds.c +++ b/board/freescale/mpc8555cds/mpc8555cds.c @@ -267,13 +267,13 @@ local_bus_init(void) lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { - lbc->lcrr |= 0x80000000; /* DLL Bypass */ + lbc->lcrr |= LCRR_DBYP; /* DLL Bypass */ } else if (lbc_hz >= 133) { - lbc->lcrr &= (~0x80000000); /* DLL Enabled */ + lbc->lcrr &= (~LCRR_DBYP); /* DLL Enabled */ } else { - lbc->lcrr &= (~0x80000000); /* DLL Enabled */ + lbc->lcrr &= (~LCRR_DBYP); /* DLL Enabled */ udelay(200); /* diff --git a/board/freescale/mpc8560ads/mpc8560ads.c b/board/freescale/mpc8560ads/mpc8560ads.c index 1a165bff86..285edbce6b 100644 --- a/board/freescale/mpc8560ads/mpc8560ads.c +++ b/board/freescale/mpc8560ads/mpc8560ads.c @@ -292,10 +292,10 @@ local_bus_init(void) lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { - lbc->lcrr = CONFIG_SYS_LBC_LCRR | 0x80000000; /* DLL Bypass */ + lbc->lcrr = CONFIG_SYS_LBC_LCRR | LCRR_DBYP; /* DLL Bypass */ } else if (lbc_hz >= 133) { - lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000); /* DLL Enabled */ + lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~LCRR_DBYP); /* DLL Enabled */ } else { /* @@ -310,7 +310,7 @@ local_bus_init(void) lbc->lcrr = 0x10000004; } - lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000);/* DLL Enabled */ + lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~LCRR_DBYP);/* DLL Enabled */ udelay(200); /* diff --git a/board/freescale/p1010rdb/ddr.c b/board/freescale/p1010rdb/ddr.c index 10c5a42d1e..6d00caffa3 100644 --- a/board/freescale/p1010rdb/ddr.c +++ b/board/freescale/p1010rdb/ddr.c @@ -147,10 +147,11 @@ phys_size_t fixed_sdram(void) cpu = gd->cpu; /* P1014 and it's derivatives support max 16bit DDR width */ if (cpu->soc_ver == SVR_P1014) { + ddr_cfg_regs.ddr_sdram_cfg &= ~SDRAM_CFG_DBW_MASK; ddr_cfg_regs.ddr_sdram_cfg |= SDRAM_CFG_16_BE; - ddr_cfg_regs.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS >> 1; - ddr_cfg_regs.ddr_sdram_cfg &= ~0x00180000; - ddr_cfg_regs.ddr_sdram_cfg |= 0x001080000; + /* divide SA and EA by two and then mask the rest so we don't + * write to reserved fields */ + ddr_cfg_regs.cs[0].bnds = (CONFIG_SYS_DDR_CS0_BNDS >> 1) & 0x0fff0fff; } ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; diff --git a/board/freescale/p1_p2_rdb_pc/law.c b/board/freescale/p1_p2_rdb_pc/law.c index 79689199c1..0da8300c6f 100644 --- a/board/freescale/p1_p2_rdb_pc/law.c +++ b/board/freescale/p1_p2_rdb_pc/law.c @@ -25,13 +25,11 @@ #include <asm/mmu.h> struct law_entry law_table[] = { -#ifndef CONFIG_NAND_SPL SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC), SET_LAW(CONFIG_SYS_PMC_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_LBC), #ifdef CONFIG_VSC7385_ENET SET_LAW(CONFIG_SYS_VSC7385_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC), #endif -#endif SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_LBC), #ifdef CONFIG_SYS_NAND_BASE_PHYS SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC), diff --git a/board/freescale/p3060qds/Makefile b/board/freescale/p3060qds/Makefile deleted file mode 100644 index ae136f4626..0000000000 --- a/board/freescale/p3060qds/Makefile +++ /dev/null @@ -1,54 +0,0 @@ -# -# Copyright 2011 Freescale Semiconductor, Inc. -# (C) Copyright 2001-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -include $(TOPDIR)/config.mk - -LIB = $(obj)lib$(BOARD).o - -COBJS-y += $(BOARD).o -COBJS-y += ddr.o -COBJS-y += eth.o -COBJS-y += fixed_ddr.o - -SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS-y)) -SOBJS := $(addprefix $(obj),$(SOBJS)) - -$(LIB): $(obj).depend $(OBJS) $(SOBJS) - $(call cmd_link_o_target, $(OBJS)) - -clean: - rm -f $(OBJS) $(SOBJS) - -distclean: clean - rm -f $(LIB) core *.bak .depend - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### diff --git a/board/freescale/p3060qds/README b/board/freescale/p3060qds/README deleted file mode 100644 index ec627980c1..0000000000 --- a/board/freescale/p3060qds/README +++ /dev/null @@ -1,110 +0,0 @@ -Overview -========= -The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC. - -The P3060 Processor combines six e500mc Power Architecture processor -cores(1.2GHz) with high-performance datapath acceleration -architecture(DPAA), CoreNet fabric infrastructure, as well as network -and peripheral bus interfaces required for networking, telecom/datacom, -wireless infrastructure, and military/aerospace applications. - - -P3060QDS Board Specifications: -============================== -Memory subsystem: - * 2G Bytes UDIMM DDR3(64bit bus) with ECC on - * 128M Bytes NOR flash single-chip memory - * 16M Bytes SPI flash - * 8K Bytes AT24C64 I2C EEPROM for RCW - -Ethernet(Default SERDES 0x19): - * FM1-dTSEC1: connected to RGMII PHY1 (Vitesse VSC8641 on board,Bottom of dual RJ45) - * FM1-dTSEC2: connected to RGMII PHY2 (Vitesse VSC8641 on board,Top of dual RJ45) - * FM1-dTSEC3: connected to SGMII PHY (Vitesse VSC8234 port1 in slot1) - * FM1-dTSEC4: connected to SGMII PHY (Vitesse VSC8234 port3 in slot1) - * FM2-dTSEC1: connected to SGMII PHY (Vitesse VSC8234 port0 in slot2) - * FM2-dTSEC2: connected to SGMII PHY (Vitesse VSC8234 port2 in slot2) - * FM2-dTSEC3: connected to SGMII PHY (Vitesse VSC8234 port0 in slot1) - * FM2-dTSEC4: connected to SGMII PHY (Vitesse VSC8234 port2 in slot1) - -PCIe: - * PCIe1: Lanes A, B, C and D of Bank1 are connected to one x4 PCIe SLOT4 - * PCIe2: Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT3 - -RapidIO: - * sRIO1: Lanes E, F, G and H of Bank1 are connected to sRIO1 (SLOT3) - * sRIO2: Lanes A, B, C and D of Bank1 are connected to sRIO2 (SLOT4) - -USB: - * USB1: connected via an external ULPI PHY SMC3315 to a TYPE-A interface - * USB2: connected via an external ULPI PHY SMC3315 to a TYPE-AB interface - -I2C: - * I2C1_CH0: EEPROM AT24C64(0x50) RCW, AT24C02(0x51) DDR SPD, - AT24C02(0x53) DDR SPD, AT24C02(0x57) SystemID, RTC DS3232(0x68) - * I2C1_CH1: 1588 RiserCard(0x55), HSLB Testport, TempMon - ADT7461(0x4C), SerDesMux DS64MB201(0x51/59/5C/5D) - * I2C1_CH2: VDD/GVDD/GIDD ZL6100 (0x21/0x22/0x23/0x24/0x40) - * I2C1_CH3: OCM CFG AT24C02(0x55), OCM IPL AT24C64(0x56) - * I2C1_CH4: PCIe SLOT1 - * I2C1_CH5: PCIe SLOT2 - * I2C1_CH6: PCIe SLOT3 - * I2C1_CH7: PCIe SLOT4 - * I2C2: NULL - * I2C3: NULL - -UART: - * Supports two UARTs up to 115200 bps for console - - -Boot from NOR flash -=================== -1. Build image - export ARCH=powerpc - export CROSS_COMPILE=/your_path/gcc-4.5.xx-eglibc-2.11.xx/powerpc-linux-gnu/bin/powerpc-linux-gnu- - make P3060QDS_config - make - -2. Program image - => tftp 1000000 u-boot.bin - => protect off all - => erase eff80000 efffffff - => cp.b 1000000 eff80000 80000 - -3. Program RCW - => tftp 1000000 rcw.bin - => protect off all - => erase e8000000 e801ffff - => cp.b 1000000 e8000000 50 - -4. Program FMAN Firmware ucode - => tftp 1000000 ucode.bin - => protect off all - => erase ef000000 ef0fffff - => cp.b 1000000 ef000000 2000 - -5. Change DIP-switch - RCW Location: SW1[1-5] = 01101 (eLBC 16bit NOR flash) - Note: 1 stands for 'on', 0 stands for 'off' - - -Using the Device Tree Source File -================================= -To create the DTB (Device Tree Binary) image file, use a command -similar to this: - dtc -O dtb -b 0 -p 1024 p3060qds.dts > p3060qds.dtb - -Or use the following command: - {linux-2.6}/make p3060qds.dtb ARCH=powerpc - -then the dtb file will be generated under the following directory: - {linux-2.6}/arch/powerpc/boot/p3060qds.dtb - - -Booting Linux -============= -Place a linux uImage in the TFTP disk area. - tftp 1000000 uImage - tftp 2000000 rootfs.ext2.gz.uboot - tftp 3000000 p3060rdb.dtb - bootm 1000000 2000000 3000000 diff --git a/board/freescale/p3060qds/ddr.c b/board/freescale/p3060qds/ddr.c deleted file mode 100644 index 9affbf09f7..0000000000 --- a/board/freescale/p3060qds/ddr.c +++ /dev/null @@ -1,248 +0,0 @@ -/* - * Copyright 2009-2011 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * Version 2 as published by the Free Software Foundation. - */ - -#include <common.h> -#include <i2c.h> -#include <hwconfig.h> -#include <asm/mmu.h> -#include <asm/fsl_ddr_sdram.h> -#include <asm/fsl_ddr_dimm_params.h> -#include <asm/fsl_law.h> - -#include "p3060qds.h" - -/* - * Fixed sdram init -- doesn't use serial presence detect. - */ - -phys_size_t fixed_sdram(void) -{ - int i; - char buf[32]; - fsl_ddr_cfg_regs_t ddr_cfg_regs; - phys_size_t ddr_size; - unsigned int lawbar1_target_id; - ulong ddr_freq, ddr_freq_mhz; - - ddr_freq = get_ddr_freq(0); - ddr_freq_mhz = ddr_freq / 1000000; - - printf("Configuring DDR for %s MT/s data rate\n", - strmhz(buf, ddr_freq)); - - for (i = 0; fixed_ddr_parm_0[i].max_freq > 0; i++) { - if ((ddr_freq_mhz > fixed_ddr_parm_0[i].min_freq) && - (ddr_freq_mhz <= fixed_ddr_parm_0[i].max_freq)) { - memcpy(&ddr_cfg_regs, - fixed_ddr_parm_0[i].ddr_settings, - sizeof(ddr_cfg_regs)); - break; - } - } - - if (fixed_ddr_parm_0[i].max_freq == 0) - panic("Unsupported DDR data rate %s MT/s data rate\n", - strmhz(buf, ddr_freq)); - - ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; - ddr_cfg_regs.ddr_cdr1 = DDR_CDR1_DHC_EN; - fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0); - - /* - * setup laws for DDR. If not interleaving, presuming half memory on - * DDR1 and the other half on DDR2 - */ - if (fixed_ddr_parm_0[i].ddr_settings->cs[0].config & 0x20000000) { - if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, - ddr_size, - LAW_TRGT_IF_DDR_INTRLV) < 0) { - printf("ERROR setting Local Access Windows for DDR\n"); - return 0; - } - } else { - lawbar1_target_id = LAW_TRGT_IF_DDR_1; - if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, - ddr_size, - lawbar1_target_id) < 0) { - printf("ERROR setting Local Access Windows for DDR\n"); - return 0; - } - } - return ddr_size; -} - -struct board_specific_params { - u32 n_ranks; - u32 datarate_mhz_high; - u32 clk_adjust; - u32 wrlvl_start; - u32 cpo; - u32 write_data_delay; - u32 force_2T; -}; - -/* - * This table contains all valid speeds we want to override with board - * specific parameters. datarate_mhz_high values need to be in ascending order - * for each n_ranks group. - */ -static const struct board_specific_params udimm[] = { - /* - * memory controller 0 - * num| hi| clk| wrlvl | cpo |wrdata|2T - * ranks| mhz|adjst| start | |delay | - */ - {4, 850, 4, 6, 0xff, 2, 0}, - {4, 950, 5, 7, 0xff, 2, 0}, - {4, 1050, 5, 8, 0xff, 2, 0}, - {4, 1250, 5, 10, 0xff, 2, 0}, - {4, 1350, 5, 11, 0xff, 2, 0}, - {4, 1666, 5, 12, 0xff, 2, 0}, - {2, 850, 5, 6, 0xff, 2, 0}, - {2, 950, 5, 7, 0xff, 2, 0}, - {2, 1250, 4, 6, 0xff, 2, 0}, - {2, 1350, 5, 7, 0xff, 2, 0}, - {2, 1666, 5, 8, 0xff, 2, 0}, - {1, 850, 4, 5, 0xff, 2, 0}, - {1, 950, 4, 7, 0xff, 2, 0}, - {1, 1666, 4, 8, 0xff, 2, 0}, - {} -}; - -static const struct board_specific_params rdimm[] = { - /* - * memory controller 0 - * num| hi| clk| wrlvl | cpo |wrdata|2T - * ranks| mhz|adjst| start | |delay | - */ - {4, 850, 4, 6, 0xff, 2, 0}, - {4, 950, 5, 7, 0xff, 2, 0}, - {4, 1050, 5, 8, 0xff, 2, 0}, - {4, 1250, 5, 10, 0xff, 2, 0}, - {4, 1350, 5, 11, 0xff, 2, 0}, - {4, 1666, 5, 12, 0xff, 2, 0}, - {2, 850, 4, 6, 0xff, 2, 0}, - {2, 1050, 4, 7, 0xff, 2, 0}, - {2, 1666, 4, 8, 0xff, 2, 0}, - {1, 850, 4, 5, 0xff, 2, 0}, - {1, 950, 4, 7, 0xff, 2, 0}, - {1, 1666, 4, 8, 0xff, 2, 0}, - {} -}; - -void fsl_ddr_board_options(memctl_options_t *popts, - dimm_params_t *pdimm, - unsigned int ctrl_num) -{ - const struct board_specific_params *pbsp, *pbsp_highest = NULL; - ulong ddr_freq; - - if (ctrl_num) { - printf("Wrong parameter for controller number %d", ctrl_num); - return; - } - if (!pdimm->n_ranks) - return; - - if (popts->registered_dimm_en) - pbsp = rdimm; - else - pbsp = udimm; - - /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr - * freqency and n_banks specified in board_specific_parameters table. - */ - ddr_freq = get_ddr_freq(0) / 1000000; - while (pbsp->datarate_mhz_high) { - if (pbsp->n_ranks == pdimm->n_ranks) { - if (ddr_freq <= pbsp->datarate_mhz_high) { - popts->cpo_override = pbsp->cpo; - popts->write_data_delay = - pbsp->write_data_delay; - popts->clk_adjust = pbsp->clk_adjust; - popts->wrlvl_start = pbsp->wrlvl_start; - popts->twoT_en = pbsp->force_2T; - goto found; - } - pbsp_highest = pbsp; - } - pbsp++; - } - - if (pbsp_highest) { - printf("Error: board specific timing not found " - "for data rate %lu MT/s!\n" - "Trying to use the highest speed (%u) parameters\n", - ddr_freq, pbsp_highest->datarate_mhz_high); - popts->cpo_override = pbsp_highest->cpo; - popts->write_data_delay = pbsp_highest->write_data_delay; - popts->clk_adjust = pbsp_highest->clk_adjust; - popts->wrlvl_start = pbsp_highest->wrlvl_start; - popts->twoT_en = pbsp_highest->force_2T; - } else { - panic("DIMM is not supported by this board"); - } - - -found: - - /* - * The datasheet of HMT125U7BFR8C-H9 blocks CL=7 as reservered. - * However SPD still claims CL=7 is supported. Extensive tests - * confirmed this board cannot work stably with CL=7 with this - * particular DIMM. - */ - if (ddr_freq >= 800 && ddr_freq < 1066 && \ - !strncmp(pdimm[0].mpart, "HMT125U7BFR8C-H9", 16)) { - popts->cas_latency_override = 1; - popts->cas_latency_override_value = 8; - debug("Override CL to 8\n"); - } - /* - * Factors to consider for half-strength driver enable: - * - number of DIMMs installed - */ - popts->half_strength_driver_enable = 0; - /* - * Write leveling override - */ - popts->wrlvl_override = 1; - popts->wrlvl_sample = 0xf; - - /* - * Rtt and Rtt_WR override - */ - popts->rtt_override = 0; - - /* Enable ZQ calibration */ - popts->zq_en = 1; - - /* DHC_EN =1, ODT = 60 Ohm */ - popts->ddr_cdr1 = DDR_CDR1_DHC_EN; -} - -phys_size_t initdram(int board_type) -{ - phys_size_t dram_size; - - puts("Initializing...."); - - if (fsl_use_spd()) { - puts("using SPD\n"); - dram_size = fsl_ddr_sdram(); - } else { - puts("using fixed parameters\n"); - dram_size = fixed_sdram(); - } - - dram_size = setup_ddr_tlbs(dram_size / 0x100000); - dram_size *= 0x100000; - - debug(" DDR: "); - return dram_size; -} diff --git a/board/freescale/p3060qds/eth.c b/board/freescale/p3060qds/eth.c deleted file mode 100644 index 3f812dbd3c..0000000000 --- a/board/freescale/p3060qds/eth.c +++ /dev/null @@ -1,482 +0,0 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <common.h> -#include <command.h> -#include <netdev.h> -#include <asm/mmu.h> -#include <asm/processor.h> -#include <asm/cache.h> -#include <asm/immap_85xx.h> -#include <asm/fsl_law.h> -#include <asm/fsl_ddr_sdram.h> -#include <asm/fsl_serdes.h> -#include <asm/fsl_portals.h> -#include <asm/fsl_liodn.h> -#include <malloc.h> -#include <fm_eth.h> -#include <fsl_mdio.h> -#include <miiphy.h> -#include <phy.h> -#include <asm/fsl_dtsec.h> - -#include "../common/qixis.h" -#include "../common/fman.h" - -#include "p3060qds_qixis.h" - -#define EMI_NONE 0xffffffff -#define EMI1_RGMII1 0 -#define EMI1_SLOT1 1 -#define EMI1_SLOT2 2 -#define EMI1_SLOT3 3 -#define EMI1_RGMII2 4 - -static int mdio_mux[NUM_FM_PORTS]; - -static char *mdio_names[5] = { - "P3060QDS_MDIO0", - "P3060QDS_MDIO1", - "P3060QDS_MDIO2", - "P3060QDS_MDIO3", - "P3060QDS_MDIO4", -}; - -/* - * Mapping of all 18 SERDES lanes to board slots. - * A value of '0' here means that the mapping must be determined - * dynamically, Lane 8/9/16/17 map to Slot1 or Aurora debug - */ -static u8 lane_to_slot[] = { - 4, 4, 4, 4, 3, 3, 3, 3, 0, 0, 2, 2, 2, 2, 1, 1, 0, 0 -}; - -static char *p3060qds_mdio_name_for_muxval(u32 muxval) -{ - return mdio_names[muxval]; -} - -struct mii_dev *mii_dev_for_muxval(u32 muxval) -{ - struct mii_dev *bus; - char *name = p3060qds_mdio_name_for_muxval(muxval); - - if (!name) { - printf("No bus for muxval %x\n", muxval); - return NULL; - } - - bus = miiphy_get_dev_by_name(name); - - if (!bus) { - printf("No bus by name %s\n", name); - return NULL; - } - - return bus; -} - -struct p3060qds_mdio { - u32 muxval; - struct mii_dev *realbus; -}; - -static void p3060qds_mux_mdio(u32 muxval) -{ - u8 brdcfg4; - - brdcfg4 = QIXIS_READ(brdcfg[4]); - brdcfg4 &= ~BRDCFG4_EMISEL_MASK; - brdcfg4 |= (muxval << 4); - QIXIS_WRITE(brdcfg[4], brdcfg4); -} - -static int p3060qds_mdio_read(struct mii_dev *bus, int addr, int devad, - int regnum) -{ - struct p3060qds_mdio *priv = bus->priv; - - p3060qds_mux_mdio(priv->muxval); - - return priv->realbus->read(priv->realbus, addr, devad, regnum); -} - -static int p3060qds_mdio_write(struct mii_dev *bus, int addr, int devad, - int regnum, u16 value) -{ - struct p3060qds_mdio *priv = bus->priv; - - p3060qds_mux_mdio(priv->muxval); - - return priv->realbus->write(priv->realbus, addr, devad, regnum, value); -} - -static int p3060qds_mdio_reset(struct mii_dev *bus) -{ - struct p3060qds_mdio *priv = bus->priv; - - return priv->realbus->reset(priv->realbus); -} - -static int p3060qds_mdio_init(char *realbusname, u32 muxval) -{ - struct p3060qds_mdio *pmdio; - struct mii_dev *bus = mdio_alloc(); - - if (!bus) { - printf("Failed to allocate P3060QDS MDIO bus\n"); - return -1; - } - - pmdio = malloc(sizeof(*pmdio)); - if (!pmdio) { - printf("Failed to allocate P3060QDS private data\n"); - free(bus); - return -1; - } - - bus->read = p3060qds_mdio_read; - bus->write = p3060qds_mdio_write; - bus->reset = p3060qds_mdio_reset; - sprintf(bus->name, p3060qds_mdio_name_for_muxval(muxval)); - - pmdio->realbus = miiphy_get_dev_by_name(realbusname); - - if (!pmdio->realbus) { - printf("No bus with name %s\n", realbusname); - free(bus); - free(pmdio); - return -1; - } - - pmdio->muxval = muxval; - bus->priv = pmdio; - - return mdio_register(bus); -} - -void board_ft_fman_fixup_port(void *blob, char * prop, phys_addr_t pa, - enum fm_port port, int offset) -{ - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - int srds_prtcl = (in_be32(&gur->rcwsr[4]) & - FSL_CORENET_RCWSR4_SRDS_PRTCL) >> 26; - - if (mdio_mux[port] == EMI1_RGMII1) - fdt_set_phy_handle(blob, prop, pa, "phy_rgmii1"); - - if (mdio_mux[port] == EMI1_RGMII2) - fdt_set_phy_handle(blob, prop, pa, "phy_rgmii2"); - - if ((mdio_mux[port] == EMI1_SLOT1) && ((srds_prtcl == 0x3) - || (srds_prtcl == 0x6))) { - switch (port) { - case FM2_DTSEC4: - fdt_set_phy_handle(blob, prop, pa, "phy2_slot1"); - break; - case FM1_DTSEC4: - fdt_set_phy_handle(blob, prop, pa, "phy3_slot1"); - break; - default: - break; - } - } - - if (mdio_mux[port] == EMI1_SLOT3) { - switch (port) { - case FM2_DTSEC3: - fdt_set_phy_handle(blob, prop, pa, "phy0_slot3"); - break; - case FM1_DTSEC3: - fdt_set_phy_handle(blob, prop, pa, "phy1_slot3"); - break; - default: - break; - } - } -} - -void fdt_fixup_board_enet(void *fdt) -{ - int i, lane, idx; - - for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { - idx = i - FM1_DTSEC1; - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_SGMII: - lane = serdes_get_first_lane(SGMII_FM1_DTSEC1 + idx); - if (lane < 0) - break; - - switch (mdio_mux[i]) { - case EMI1_SLOT1: - if (lane >= 14) { - fdt_status_okay_by_alias(fdt, - "emi1_slot1"); - fdt_status_disabled_by_alias(fdt, - "emi1_slot1_bk1"); - } else { - fdt_status_disabled_by_alias(fdt, - "emi1_slot1"); - fdt_status_okay_by_alias(fdt, - "emi1_slot1_bk1"); - } - break; - case EMI1_SLOT2: - fdt_status_okay_by_alias(fdt, "emi1_slot2"); - break; - case EMI1_SLOT3: - fdt_status_okay_by_alias(fdt, "emi1_slot3"); - break; - } - break; - case PHY_INTERFACE_MODE_RGMII: - if (i == FM1_DTSEC1) - fdt_status_okay_by_alias(fdt, "emi1_rgmii1"); - - if (i == FM1_DTSEC2) - fdt_status_okay_by_alias(fdt, "emi1_rgmii2"); - break; - default: - break; - } - } -#if (CONFIG_SYS_NUM_FMAN == 2) - for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) { - idx = i - FM2_DTSEC1; - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_SGMII: - lane = serdes_get_first_lane(SGMII_FM2_DTSEC1 + idx); - if (lane >= 0) { - switch (mdio_mux[i]) { - case EMI1_SLOT1: - if (lane >= 14) - fdt_status_okay_by_alias(fdt, - "emi1_slot1"); - else - fdt_status_okay_by_alias(fdt, - "emi1_slot1_bk1"); - break; - case EMI1_SLOT2: - fdt_status_okay_by_alias(fdt, - "emi1_slot2"); - break; - case EMI1_SLOT3: - fdt_status_okay_by_alias(fdt, - "emi1_slot3"); - break; - } - } - break; - default: - break; - } - } -#endif -} - -static void initialize_lane_to_slot(void) -{ - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - int sdprtl = (in_be32(&gur->rcwsr[4]) & - FSL_CORENET_RCWSR4_SRDS_PRTCL) >> 26; - - switch (sdprtl) { - case 0x03: - case 0x06: - lane_to_slot[8] = 1; - lane_to_slot[9] = lane_to_slot[8]; - lane_to_slot[16] = 5; - lane_to_slot[17] = lane_to_slot[16]; - break; - case 0x16: - case 0x19: - case 0x1C: - lane_to_slot[8] = 5; - lane_to_slot[9] = lane_to_slot[8]; - lane_to_slot[16] = 1; - lane_to_slot[17] = lane_to_slot[16]; - break; - default: - puts("Invalid SerDes protocol for P3060QDS\n"); - break; - } -} - -int board_eth_init(bd_t *bis) -{ -#ifdef CONFIG_FMAN_ENET - struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR; - int i; - struct fsl_pq_mdio_info dtsec_mdio_info; - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - int srds_cfg = (in_be32(&gur->rcwsr[4]) & - FSL_CORENET_RCWSR4_SRDS_PRTCL) >> 26; - - initialize_lane_to_slot(); - - /* - * Set TBIPA on FM1@DTSEC1. This is needed for configurations - * where FM1@DTSEC1 isn't used directly, since it provides - * MDIO for other ports. - */ - out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE); - - /* Initialize the mdio_mux array so we can recognize empty elements */ - for (i = 0; i < NUM_FM_PORTS; i++) - mdio_mux[i] = EMI_NONE; - - dtsec_mdio_info.regs = - (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR; - dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; - - /* Register the 1G MDIO bus */ - fsl_pq_mdio_init(bis, &dtsec_mdio_info); - - /* Register the 5 muxing front-ends to the MDIO buses */ - if (fm_info_get_enet_if(FM1_DTSEC1) == PHY_INTERFACE_MODE_RGMII) - p3060qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1); - - if (fm_info_get_enet_if(FM1_DTSEC2) == PHY_INTERFACE_MODE_RGMII) - p3060qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2); - p3060qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1); - p3060qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2); - p3060qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3); - - if (fm_info_get_enet_if(FM1_DTSEC1) == PHY_INTERFACE_MODE_RGMII) - fm_info_set_phy_address(FM1_DTSEC1, 1); /* RGMII1 */ - else if (fm_info_get_enet_if(FM1_DTSEC1) == PHY_INTERFACE_MODE_SGMII) - fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT2_PHY_ADDR); - - if (fm_info_get_enet_if(FM1_DTSEC2) == PHY_INTERFACE_MODE_RGMII) - fm_info_set_phy_address(FM1_DTSEC2, 2); /* RGMII2 */ - else if (fm_info_get_enet_if(FM1_DTSEC2) == PHY_INTERFACE_MODE_SGMII) - fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR); - - fm_info_set_phy_address(FM2_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); - fm_info_set_phy_address(FM2_DTSEC2, SGMII_CARD_PORT3_PHY_ADDR); - - switch (srds_cfg) { - case 0x03: - case 0x06: - fm_info_set_phy_address(FM2_DTSEC3, SGMII_CARD_PORT3_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT4_PHY_ADDR); - fm_info_set_phy_address(FM2_DTSEC4, SGMII_CARD_PORT1_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC4, SGMII_CARD_PORT2_PHY_ADDR); - break; - case 0x16: - case 0x19: - case 0x1C: - fm_info_set_phy_address(FM2_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT2_PHY_ADDR); - fm_info_set_phy_address(FM2_DTSEC4, SGMII_CARD_PORT3_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC4, SGMII_CARD_PORT4_PHY_ADDR); - break; - default: - puts("Invalid SerDes protocol for P3060QDS\n"); - break; - } - - for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { - int idx = i - FM1_DTSEC1, lane, slot; - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_SGMII: - lane = serdes_get_first_lane(SGMII_FM1_DTSEC1 + idx); - if (lane < 0) - break; - slot = lane_to_slot[lane]; - if (QIXIS_READ(present) & (1 << (slot - 1))) - fm_disable_port(i); - switch (slot) { - case 1: - mdio_mux[i] = EMI1_SLOT1; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - break; - case 2: - mdio_mux[i] = EMI1_SLOT2; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - break; - case 3: - mdio_mux[i] = EMI1_SLOT3; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - break; - }; - break; - case PHY_INTERFACE_MODE_RGMII: - if (i == FM1_DTSEC1) { - mdio_mux[i] = EMI1_RGMII1; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - } else if (i == FM1_DTSEC2) { - mdio_mux[i] = EMI1_RGMII2; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - } - break; - default: - break; - } - } - -#if (CONFIG_SYS_NUM_FMAN == 2) - for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) { - int idx = i - FM2_DTSEC1, lane, slot; - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_SGMII: - lane = serdes_get_first_lane(SGMII_FM2_DTSEC1 + idx); - if (lane < 0) - break; - slot = lane_to_slot[lane]; - if (QIXIS_READ(present) & (1 << (slot - 1))) - fm_disable_port(i); - switch (slot) { - case 1: - mdio_mux[i] = EMI1_SLOT1; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - break; - case 2: - mdio_mux[i] = EMI1_SLOT2; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - break; - case 3: - mdio_mux[i] = EMI1_SLOT3; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - break; - }; - break; - default: - break; - } - } -#endif /* CONFIG_SYS_NUM_FMAN */ - - cpu_eth_init(bis); -#endif /* CONFIG_FMAN_ENET */ - - return pci_eth_init(bis); -} diff --git a/board/freescale/p3060qds/fixed_ddr.c b/board/freescale/p3060qds/fixed_ddr.c deleted file mode 100644 index 125988da82..0000000000 --- a/board/freescale/p3060qds/fixed_ddr.c +++ /dev/null @@ -1,214 +0,0 @@ -/* - * Copyright 2009-2011 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * Version 2 as published by the Free Software Foundation. - */ - -#include <common.h> -#include <asm/fsl_ddr_sdram.h> - -#define CONFIG_SYS_DDR_TIMING_3_1200 0x01030000 -#define CONFIG_SYS_DDR_TIMING_0_1200 0xCC550104 -#define CONFIG_SYS_DDR_TIMING_1_1200 0x868FAA45 -#define CONFIG_SYS_DDR_TIMING_2_1200 0x0FB8A912 -#define CONFIG_SYS_DDR_MODE_1_1200 0x00441A40 -#define CONFIG_SYS_DDR_MODE_2_1200 0x00100000 -#define CONFIG_SYS_DDR_INTERVAL_1200 0x12480100 -#define CONFIG_SYS_DDR_CLK_CTRL_1200 0x02800000 - -#define CONFIG_SYS_DDR_TIMING_3_1000 0x00020000 -#define CONFIG_SYS_DDR_TIMING_0_1000 0xCC440104 -#define CONFIG_SYS_DDR_TIMING_1_1000 0x727DF944 -#define CONFIG_SYS_DDR_TIMING_2_1000 0x0FB088CF -#define CONFIG_SYS_DDR_MODE_1_1000 0x00441830 -#define CONFIG_SYS_DDR_MODE_2_1000 0x00080000 -#define CONFIG_SYS_DDR_INTERVAL_1000 0x0F3C0100 -#define CONFIG_SYS_DDR_CLK_CTRL_1000 0x02800000 - -#define CONFIG_SYS_DDR_TIMING_3_900 0x00020000 -#define CONFIG_SYS_DDR_TIMING_0_900 0xCC440104 -#define CONFIG_SYS_DDR_TIMING_1_900 0x616ba844 -#define CONFIG_SYS_DDR_TIMING_2_900 0x0fb088ce -#define CONFIG_SYS_DDR_MODE_1_900 0x00441620 -#define CONFIG_SYS_DDR_MODE_2_900 0x00080000 -#define CONFIG_SYS_DDR_INTERVAL_900 0x0db60100 -#define CONFIG_SYS_DDR_CLK_CTRL_900 0x02800000 - -#define CONFIG_SYS_DDR_TIMING_3_800 0x00020000 -#define CONFIG_SYS_DDR_TIMING_0_800 0xcc330104 -#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b4744 -#define CONFIG_SYS_DDR_TIMING_2_800 0x0fa888cc -#define CONFIG_SYS_DDR_MODE_1_800 0x00441420 -#define CONFIG_SYS_DDR_MODE_2_800 0x00000000 -#define CONFIG_SYS_DDR_INTERVAL_800 0x0c300100 -#define CONFIG_SYS_DDR_CLK_CTRL_800 0x02800000 - -#define CONFIG_SYS_DDR_CS0_BNDS 0x000000FF -#define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 -#define CONFIG_SYS_DDR_CS2_BNDS 0x000000FF -#define CONFIG_SYS_DDR_CS3_BNDS 0x000000FF -#define CONFIG_SYS_DDR2_CS0_BNDS 0x000000FF -#define CONFIG_SYS_DDR2_CS1_BNDS 0x00000000 -#define CONFIG_SYS_DDR2_CS2_BNDS 0x000000FF -#define CONFIG_SYS_DDR2_CS3_BNDS 0x000000FF -#define CONFIG_SYS_DDR_CS0_CONFIG 0xA0044202 -#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 -#define CONFIG_SYS_DDR_CS1_CONFIG 0x80004202 -#define CONFIG_SYS_DDR_CS2_CONFIG 0x00000000 -#define CONFIG_SYS_DDR_CS3_CONFIG 0x00000000 -#define CONFIG_SYS_DDR2_CS0_CONFIG 0x80044202 -#define CONFIG_SYS_DDR2_CS1_CONFIG 0x80004202 -#define CONFIG_SYS_DDR2_CS2_CONFIG 0x00000000 -#define CONFIG_SYS_DDR2_CS3_CONFIG 0x00000000 -#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 -#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 -#define CONFIG_SYS_DDR_CS1_CONFIG 0x80004202 -#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef -#define CONFIG_SYS_DDR_TIMING_4 0x00000001 -#define CONFIG_SYS_DDR_TIMING_5 0x02401400 -#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 -#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600 -#define CONFIG_SYS_DDR_WRLVL_CNTL 0x8675F607 -#define CONFIG_SYS_DDR_SDRAM_CFG 0xE7044000 -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x24401031 -#define CONFIG_SYS_DDR_RCW_1 0x00000000 -#define CONFIG_SYS_DDR_RCW_2 0x00000000 -#define CONFIG_MEM_INIT_VALUE 0xdeadbeef - -fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = { - .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS, - .cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS, - .cs[2].bnds = CONFIG_SYS_DDR_CS2_BNDS, - .cs[3].bnds = CONFIG_SYS_DDR_CS3_BNDS, - .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG, - .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2, - .cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG, - .cs[2].config = CONFIG_SYS_DDR_CS2_CONFIG, - .cs[3].config = CONFIG_SYS_DDR_CS3_CONFIG, - .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_800, - .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_800, - .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_800, - .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_800, - .ddr_sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG, - .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_SDRAM_CFG2, - .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_800, - .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_800, - .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL, - .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_800, - .ddr_data_init = CONFIG_MEM_INIT_VALUE, - .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_800, - .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR, - .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR, - .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4, - .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5, - .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CNTL, - .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CNTL, - .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1, - .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2 -}; - -fsl_ddr_cfg_regs_t ddr_cfg_regs_900 = { - .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS, - .cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS, - .cs[2].bnds = CONFIG_SYS_DDR_CS2_BNDS, - .cs[3].bnds = CONFIG_SYS_DDR_CS3_BNDS, - .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG, - .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2, - .cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG, - .cs[2].config = CONFIG_SYS_DDR_CS2_CONFIG, - .cs[3].config = CONFIG_SYS_DDR_CS3_CONFIG, - .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_900, - .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_900, - .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_900, - .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_900, - .ddr_sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG, - .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_SDRAM_CFG2, - .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_900, - .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_900, - .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL, - .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_900, - .ddr_data_init = CONFIG_MEM_INIT_VALUE, - .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_900, - .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR, - .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR, - .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4, - .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5, - .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CNTL, - .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CNTL, - .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1, - .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2 -}; - -fsl_ddr_cfg_regs_t ddr_cfg_regs_1000 = { - .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS, - .cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS, - .cs[2].bnds = CONFIG_SYS_DDR_CS2_BNDS, - .cs[3].bnds = CONFIG_SYS_DDR_CS3_BNDS, - .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG, - .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2, - .cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG, - .cs[2].config = CONFIG_SYS_DDR_CS2_CONFIG, - .cs[3].config = CONFIG_SYS_DDR_CS3_CONFIG, - .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_1000, - .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_1000, - .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_1000, - .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_1000, - .ddr_sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG, - .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_SDRAM_CFG2, - .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_1000, - .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_1000, - .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL, - .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_1000, - .ddr_data_init = CONFIG_MEM_INIT_VALUE, - .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_1000, - .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR, - .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR, - .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4, - .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5, - .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CNTL, - .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CNTL, - .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1, - .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2 -}; - -fsl_ddr_cfg_regs_t ddr_cfg_regs_1200 = { - .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS, - .cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS, - .cs[2].bnds = CONFIG_SYS_DDR_CS2_BNDS, - .cs[3].bnds = CONFIG_SYS_DDR_CS3_BNDS, - .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG, - .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2, - .cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG, - .cs[2].config = CONFIG_SYS_DDR_CS2_CONFIG, - .cs[3].config = CONFIG_SYS_DDR_CS3_CONFIG, - .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_1200, - .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_1200, - .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_1200, - .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_1200, - .ddr_sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG, - .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_SDRAM_CFG2, - .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_1200, - .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_1200, - .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL, - .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_1200, - .ddr_data_init = CONFIG_MEM_INIT_VALUE, - .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_1200, - .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR, - .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR, - .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4, - .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5, - .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CNTL, - .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CNTL, - .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1, - .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2 -}; - -fixed_ddr_parm_t fixed_ddr_parm_0[] = { - {750, 850, &ddr_cfg_regs_800}, - {850, 950, &ddr_cfg_regs_900}, - {950, 1050, &ddr_cfg_regs_1000}, - {1050, 1250, &ddr_cfg_regs_1200}, - {0, 0, NULL} -}; diff --git a/board/freescale/p3060qds/p3060qds.c b/board/freescale/p3060qds/p3060qds.c deleted file mode 100644 index 43e7f2888a..0000000000 --- a/board/freescale/p3060qds/p3060qds.c +++ /dev/null @@ -1,342 +0,0 @@ -/* - * Copyright 2011-2012 Freescale Semiconductor, Inc. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <common.h> -#include <command.h> -#include <netdev.h> -#include <linux/compiler.h> -#include <asm/mmu.h> -#include <asm/processor.h> -#include <asm/cache.h> -#include <asm/immap_85xx.h> -#include <asm/fsl_law.h> -#include <asm/fsl_serdes.h> -#include <asm/fsl_portals.h> -#include <asm/fsl_liodn.h> -#include <fm_eth.h> -#include <configs/P3060QDS.h> -#include <libfdt.h> -#include <fdt_support.h> - -#include "../common/qixis.h" -#include "p3060qds.h" -#include "p3060qds_qixis.h" - -DECLARE_GLOBAL_DATA_PTR; - -int checkboard(void) -{ - u8 sw; - struct cpu_type *cpu = gd->cpu; - ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; - unsigned int i; - - printf("Board: %s", cpu->name); - puts("QDS, "); - - printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", - QIXIS_READ(id), QIXIS_READ(arch), QIXIS_READ(scver)); - - sw = QIXIS_READ(brdcfg[0]); - sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; - - if (sw < 0x8) - printf("vBank: %d\n", sw); - else if (sw == 0x8) - puts("Promjet\n"); - else if (sw == 0x9) - puts("NAND\n"); - else - printf("invalid setting of SW%u\n", PIXIS_LBMAP_SWITCH); - - puts("Reset Configuration Word (RCW):"); - for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) { - u32 rcw = in_be32(&gur->rcwsr[i]); - - if ((i % 4) == 0) - printf("\n %08x:", i * 4); - printf(" %08x", rcw); - } - puts("\n"); - - puts("SERDES Reference Clocks: "); - sw = QIXIS_READ(brdcfg[2]); - for (i = 0; i < 3; i++) { - static const char * const freq[] = {"100", "125", "Reserved", - "156.25"}; - unsigned int clock = (sw >> (2 * i)) & 3; - - printf("Bank%u=%sMhz ", i+1, freq[clock]); - } - puts("\n"); - - return 0; -} - -int board_early_init_f(void) -{ - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - - /* only single DDR controller on QDS board, disable DDR1_MCK4/5 */ - setbits_be32(&gur->ddrclkdr, 0x00030000); - - return 0; -} - -void board_config_serdes_mux(void) -{ - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - int cfg = (in_be32(&gur->rcwsr[4]) & - FSL_CORENET_RCWSR4_SRDS_PRTCL) >> 26; - - switch (cfg) { - case 0x03: - case 0x06: - /* set Lane I,J as SGMII */ - QIXIS_WRITE(brdcfg[6], BRDCFG6_SD4MX_B | BRDCFG6_SD3MX_A | - BRDCFG6_SD2MX_B | BRDCFG6_SD1MX_A); - break; - case 0x16: - case 0x19: - case 0x1c: - /* set Lane I,J as Aurora Debug */ - QIXIS_WRITE(brdcfg[6], BRDCFG6_SD4MX_A | BRDCFG6_SD3MX_B | - BRDCFG6_SD2MX_A | BRDCFG6_SD1MX_B); - break; - default: - puts("Invalid SerDes protocol for P3060QDS\n"); - break; - } -} - -void board_config_usb_mux(void) -{ - u8 brdcfg4, brdcfg5, brdcfg7; - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 rcwsr11 = in_be32(&gur->rcwsr[11]); - u32 ec1 = rcwsr11 & FSL_CORENET_RCWSR11_EC1; - u32 ec2 = rcwsr11 & FSL_CORENET_RCWSR11_EC2; - - brdcfg4 = QIXIS_READ(brdcfg[4]); - brdcfg4 &= ~BRDCFG4_EC_MODE_MASK; - if ((ec1 == FSL_CORENET_RCWSR11_EC1_FM1_USB1) && - (ec2 == FSL_CORENET_RCWSR11_EC2_USB2)) { - brdcfg4 |= BRDCFG4_EC2_USB_EC1_USB; - - } else if ((ec1 == FSL_CORENET_RCWSR11_EC1_FM1_USB1) && - ((ec2 == FSL_CORENET_RCWSR11_EC2_FM1_DTSEC2) || - (ec2 == FSL_CORENET_RCWSR11_EC2_FM2_DTSEC1))) { - brdcfg4 |= BRDCFG4_EC2_RGMII_EC1_USB; - - } else if ((ec1 == FSL_CORENET_RCWSR11_EC1_FM1_DTSEC1) && - (ec2 == FSL_CORENET_RCWSR11_EC2_USB2)) { - brdcfg4 |= BRDCFG4_EC2_USB_EC1_RGMII; - - } else if ((ec1 == FSL_CORENET_RCWSR11_EC1_FM1_DTSEC1) && - ((ec2 == FSL_CORENET_RCWSR11_EC2_FM1_DTSEC2) || - (ec2 == FSL_CORENET_RCWSR11_EC2_FM2_DTSEC1))) { - brdcfg4 |= BRDCFG4_EC2_RGMII_EC1_RGMII; - } else { - brdcfg4 |= BRDCFG4_EC2_MII_EC1_MII; - } - QIXIS_WRITE(brdcfg[4], brdcfg4); - - brdcfg5 = QIXIS_READ(brdcfg[5]); - brdcfg5 &= ~(BRDCFG5_USB1ID_MASK | BRDCFG5_USB2ID_MASK); - brdcfg5 |= (BRDCFG5_USB1ID_CTRL | BRDCFG5_USB2ID_CTRL); - QIXIS_WRITE(brdcfg[5], brdcfg5); - - brdcfg7 = BRDCFG7_JTAGMX_COP_JTAG | BRDCFG7_IQ1MX_IRQ_EVT | - BRDCFG7_G1MX_USB1 | BRDCFG7_D1MX_TSEC3USB | BRDCFG7_I3MX_USB1; - QIXIS_WRITE(brdcfg[7], brdcfg7); -} - -int board_early_init_r(void) -{ - const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; - const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); - - /* - * Remap Boot flash + PROMJET region to caching-inhibited - * so that flash can be erased properly. - */ - - /* Flush d-cache and invalidate i-cache of any FLASH data */ - flush_dcache(); - invalidate_icache(); - - /* invalidate existing TLB entry for flash + promjet */ - disable_tlb(flash_esel); - - set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, flash_esel, BOOKE_PAGESZ_256M, 1); - - set_liodns(); -#ifdef CONFIG_SYS_DPAA_QBMAN - setup_portals(); -#endif - board_config_serdes_mux(); - board_config_usb_mux(); - - return 0; -} - -static const char *serdes_clock_to_string(u32 clock) -{ - switch (clock) { - case SRDS_PLLCR0_RFCK_SEL_100: - return "100"; - case SRDS_PLLCR0_RFCK_SEL_125: - return "125"; - case SRDS_PLLCR0_RFCK_SEL_156_25: - return "156.25"; - default: - return "150"; - } -} - -#define NUM_SRDS_BANKS 3 - -int misc_init_r(void) -{ - serdes_corenet_t *srds_regs; - u32 actual[NUM_SRDS_BANKS]; - unsigned int i; - u8 sw; - - sw = QIXIS_READ(brdcfg[2]); - for (i = 0; i < 3; i++) { - unsigned int clock = (sw >> (2 * i)) & 3; - switch (clock) { - case 0: - actual[i] = SRDS_PLLCR0_RFCK_SEL_100; - break; - case 1: - actual[i] = SRDS_PLLCR0_RFCK_SEL_125; - break; - case 3: - actual[i] = SRDS_PLLCR0_RFCK_SEL_156_25; - break; - default: - printf("Warning: SDREFCLK%u switch setting of '10' is " - "unsupported\n", i + 1); - break; - } - } - - srds_regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; - for (i = 0; i < NUM_SRDS_BANKS; i++) { - u32 pllcr0 = in_be32(&srds_regs->bank[i].pllcr0); - u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK; - if (expected != actual[i]) { - printf("Warning: SERDES bank %u expects reference clock" - " %sMHz, but actual is %sMHz\n", i + 1, - serdes_clock_to_string(expected), - serdes_clock_to_string(actual[i])); - } - } - - return 0; -} - -/* - * This is map of CVDD values. 33 means CVDD is 3.3v, 25 means CVDD is 2.5v, - * 18 means CVDD is 1.8v. - */ -static u8 IO_VSEL[] = { - 33, 33, 33, 25, 25, 25, 18, 18, 18, - 33, 33, 33, 25, 25, 25, 18, 18, 18, - 33, 33, 33, 25, 25, 25, 18, 18, 18, - 33, 33, 33, 33, 33 -}; - -#define IO_VSEL_MASK 0x1f - -/* - * different CVDD selects diffenert spi flashs, read dutcfg[3] to get CVDD, - * then set status of spi flash nodes to 'disabled' according to CVDD. - * CVDD '33' will select spi flash0 and flash1, CVDD '25' will select spi - * flash2, CVDD '18' will select spi flash3. - */ -void fdt_fixup_board_spi(void *blob) -{ - u8 sw5 = QIXIS_READ(dutcfg[3]); - - switch (IO_VSEL[sw5 & IO_VSEL_MASK]) { - /* 3.3v */ - case 33: - do_fixup_by_compat(blob, "atmel,at45db081d", "status", - "disabled", strlen("disabled") + 1, 1); - do_fixup_by_compat(blob, "spansion,sst25wf040", "status", - "disabled", strlen("disabled") + 1, 1); - break; - /* 2.5v */ - case 25: - do_fixup_by_compat(blob, "spansion,s25sl12801", "status", - "disabled", strlen("disabled") + 1, 1); - do_fixup_by_compat(blob, "spansion,en25q32", "status", - "disabled", strlen("disabled") + 1, 1); - do_fixup_by_compat(blob, "spansion,sst25wf040", "status", - "disabled", strlen("disabled") + 1, 1); - break; - /* 1.8v */ - case 18: - do_fixup_by_compat(blob, "spansion,s25sl12801", "status", - "disabled", strlen("disabled") + 1, 1); - do_fixup_by_compat(blob, "spansion,en25q32", "status", - "disabled", strlen("disabled") + 1, 1); - do_fixup_by_compat(blob, "atmel,at45db081d", "status", - "disabled", strlen("disabled") + 1, 1); - break; - } -} - -void ft_board_setup(void *blob, bd_t *bd) -{ - phys_addr_t base; - phys_size_t size; - - ft_cpu_setup(blob, bd); - - base = getenv_bootm_low(); - size = getenv_bootm_size(); - - fdt_fixup_memory(blob, (u64)base, (u64)size); - -#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) - fdt_fixup_dr_usb(blob, bd); -#endif - -#ifdef CONFIG_PCI - pci_of_setup(blob, bd); -#endif - - fdt_fixup_liodn(blob); - fdt_fixup_dr_usb(blob, bd); - fdt_fixup_board_spi(blob); - -#ifdef CONFIG_SYS_DPAA_FMAN - fdt_fixup_fman_ethernet(blob); - fdt_fixup_board_enet(blob); -#endif -} diff --git a/board/freescale/p3060qds/p3060qds_qixis.h b/board/freescale/p3060qds/p3060qds_qixis.h deleted file mode 100644 index 4d5d6a25eb..0000000000 --- a/board/freescale/p3060qds/p3060qds_qixis.h +++ /dev/null @@ -1,74 +0,0 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef __P3060QDS_QIXIS_H__ -#define __P3060QDS_QIXIS_H__ - -/* Definitions of QIXIS Registers for P3060QDS */ - -/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */ -#define BRDCFG4_EC_MODE_MASK 0x0F -#define BRDCFG4_EC2_MII_EC1_MII 0x00 -#define BRDCFG4_EC2_MII_EC1_USB 0x03 -#define BRDCFG4_EC2_USB_EC1_MII 0x0C -#define BRDCFG4_EC2_USB_EC1_USB 0x0F -#define BRDCFG4_EC2_USB_EC1_RGMII 0x0E -#define BRDCFG4_EC2_RGMII_EC1_USB 0x0B -#define BRDCFG4_EC2_RGMII_EC1_RGMII 0x0A -#define BRDCFG4_EMISEL_MASK 0xF0 - -#define BRDCFG5_ECLKS_MASK 0x80 -#define BRDCFG5_USB1ID_MASK 0x40 -#define BRDCFG5_USB2ID_MASK 0x20 -#define BRDCFG5_GC2MX_MASK 0x0C -#define BRDCFG5_T15MX_MASK 0x03 -#define BRDCFG5_ECLKS_IEEE1588_CM 0x80 -#define BRDCFG5_USB1ID_CTRL 0x40 -#define BRDCFG5_USB2ID_CTRL 0x20 - -#define BRDCFG6_SD1MX_A 0x01 -#define BRDCFG6_SD1MX_B 0x00 -#define BRDCFG6_SD2MX_A 0x02 -#define BRDCFG6_SD2MX_B 0x00 -#define BRDCFG6_SD3MX_A 0x04 -#define BRDCFG6_SD3MX_B 0x00 -#define BRDCFG6_SD4MX_A 0x08 -#define BRDCFG6_SD4MX_B 0x00 - -#define BRDCFG7_JTAGMX_MASK 0xC0 -#define BRDCFG7_IQ1MX_MASK 0x20 -#define BRDCFG7_G1MX_MASK 0x10 -#define BRDCFG7_D1MX_MASK 0x0C -#define BRDCFG7_I3MX_MASK 0x03 -#define BRDCFG7_JTAGMX_AURORA 0x00 -#define BRDCFG7_JTAGMX_FPGA 0x80 -#define BRDCFG7_JTAGMX_COP_JTAG 0xC0 -#define BRDCFG7_IQ1MX_IRQ_EVT 0x00 -#define BRDCFG7_IQ1MX_USB2 0x20 -#define BRDCFG7_G1MX_USB1 0x00 -#define BRDCFG7_G1MX_TSEC3 0x10 -#define BRDCFG7_D1MX_DMA 0x00 -#define BRDCFG7_D1MX_TSEC3USB 0x04 -#define BRDCFG7_D1MX_HDLC2 0x08 -#define BRDCFG7_I3MX_UART2_I2C34 0x00 -#define BRDCFG7_I3MX_GPIO_EVT 0x01 -#define BRDCFG7_I3MX_USB1 0x02 -#define BRDCFG7_I3MX_TSEC3 0x03 - -#endif diff --git a/boards.cfg b/boards.cfg index 091c79f5cf..f789539e85 100644 --- a/boards.cfg +++ b/boards.cfg @@ -809,29 +809,24 @@ P2041RDB_NAND powerpc mpc85xx p2041rdb freescale P2041RDB_SDCARD powerpc mpc85xx p2041rdb freescale - P2041RDB:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000 P2041RDB_SECURE_BOOT powerpc mpc85xx p2041rdb freescale - P2041RDB:SECURE_BOOT P2041RDB_SPIFLASH powerpc mpc85xx p2041rdb freescale - P2041RDB:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 +P2041RDB_SRIO_PCIE_BOOT powerpc mpc85xx p2041rdb freescale - P2041RDB:SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 P3041DS powerpc mpc85xx corenet_ds freescale P3041DS_NAND powerpc mpc85xx corenet_ds freescale - P3041DS:RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000 P3041DS_SDCARD powerpc mpc85xx corenet_ds freescale - P3041DS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000 P3041DS_SECURE_BOOT powerpc mpc85xx corenet_ds freescale - P3041DS:SECURE_BOOT P3041DS_SPIFLASH powerpc mpc85xx corenet_ds freescale - P3041DS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 -P3041DS_SRIOBOOT_MASTER powerpc mpc85xx corenet_ds freescale - P3041DS:SRIOBOOT_MASTER -P3041DS_SRIOBOOT_SLAVE powerpc mpc85xx corenet_ds freescale - P3041DS:SRIOBOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 -P3060QDS powerpc mpc85xx p3060qds freescale -P3060QDS_NAND powerpc mpc85xx p3060qds freescale - P3060QDS:RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000 -P3060QDS_SECURE_BOOT powerpc mpc85xx p3060qds freescale - P3060QDS:SECURE_BOOT +P3041DS_SRIO_PCIE_BOOT powerpc mpc85xx corenet_ds freescale - P3041DS:SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 P4080DS powerpc mpc85xx corenet_ds freescale P4080DS_SDCARD powerpc mpc85xx corenet_ds freescale - P4080DS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000 P4080DS_SECURE_BOOT powerpc mpc85xx corenet_ds freescale - P4080DS:SECURE_BOOT P4080DS_SPIFLASH powerpc mpc85xx corenet_ds freescale - P4080DS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 -P4080DS_SRIOBOOT_MASTER powerpc mpc85xx corenet_ds freescale - P4080DS:SRIOBOOT_MASTER -P4080DS_SRIOBOOT_SLAVE powerpc mpc85xx corenet_ds freescale - P4080DS:SRIOBOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 +P4080DS_SRIO_PCIE_BOOT powerpc mpc85xx corenet_ds freescale - P4080DS:SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 P5020DS powerpc mpc85xx corenet_ds freescale P5020DS_NAND powerpc mpc85xx corenet_ds freescale - P5020DS:RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000 P5020DS_SDCARD powerpc mpc85xx corenet_ds freescale - P5020DS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000 P5020DS_SECURE_BOOT powerpc mpc85xx corenet_ds freescale - P5020DS:SECURE_BOOT P5020DS_SPIFLASH powerpc mpc85xx corenet_ds freescale - P5020DS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 -P5020DS_SRIOBOOT_MASTER powerpc mpc85xx corenet_ds freescale - P5020DS:SRIOBOOT_MASTER -P5020DS_SRIOBOOT_SLAVE powerpc mpc85xx corenet_ds freescale - P5020DS:SRIOBOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 +P5020DS_SRIO_PCIE_BOOT powerpc mpc85xx corenet_ds freescale - P5020DS:SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 BSC9131RDB_SPIFLASH powerpc mpc85xx bsc9131rdb freescale - BSC9131RDB:BSC9131RDB,SPIFLASH stxgp3 powerpc mpc85xx stxgp3 stx stxssa powerpc mpc85xx stxssa stx - stxssa diff --git a/common/env_remote.c b/common/env_remote.c index 3bf0f957b3..a7b147b20d 100644 --- a/common/env_remote.c +++ b/common/env_remote.c @@ -62,8 +62,8 @@ int env_init(void) #ifdef CONFIG_CMD_SAVEENV int saveenv(void) { -#ifdef CONFIG_SRIOBOOT_SLAVE - printf("Can not support the 'saveenv' when boot from SRIO!\n"); +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE + printf("Can not support the 'saveenv' when boot from SRIO or PCIE!\n"); return 1; #else return 0; diff --git a/common/image.c b/common/image.c index 70a112d36f..f084d2baed 100644 --- a/common/image.c +++ b/common/image.c @@ -143,6 +143,7 @@ static const table_entry_t uimage_type[] = { { IH_TYPE_INVALID, NULL, "Invalid Image", }, { IH_TYPE_MULTI, "multi", "Multi-File Image", }, { IH_TYPE_OMAPIMAGE, "omapimage", "TI OMAP SPL With GP CH",}, + { IH_TYPE_PBLIMAGE, "pblimage", "Freescale PBL Boot Image",}, { IH_TYPE_RAMDISK, "ramdisk", "RAMDisk Image", }, { IH_TYPE_SCRIPT, "script", "Script", }, { IH_TYPE_STANDALONE, "standalone", "Standalone Program", }, diff --git a/doc/README.fsl-ddr b/doc/README.fsl-ddr index 5e21658765..f94b56f628 100644 --- a/doc/README.fsl-ddr +++ b/doc/README.fsl-ddr @@ -1,5 +1,28 @@ - -Table of interleaving modes supported in cpu/8xxx/ddr/ +Table of interleaving 2-4 controllers +===================================== + +--------------+-----------------------------------------------------------+ + |Configuration | Memory Controller | + | | 1 2 3 4 | + |--------------+--------------+--------------+-----------------------------+ + | Two memory | Not Intlv'ed | Not Intlv'ed | | + | complexes +--------------+--------------+ | + | | 2-way Intlv'ed | | + |--------------+--------------+--------------+--------------+ | + | | Not Intlv'ed | Not Intlv'ed | Not Intlv'ed | | + | Three memory +--------------+--------------+--------------+ | + | complexes | 2-way Intlv'ed | Not Intlv'ed | | + | +-----------------------------+--------------+ | + | | 3-way Intlv'ed | | + +--------------+--------------+--------------+--------------+--------------+ + | | Not Intlv'ed | Not Intlv'ed | Not Intlv'ed | Not Intlv'ed | + | Four memory +--------------+--------------+--------------+--------------+ + | complexes | 2-way Intlv'ed | 2-way Intlv'ed | + | +-----------------------------+-----------------------------+ + | | 4-way Intlv'ed | + +--------------+-----------------------------------------------------------+ + + +Table of 2-way interleaving modes supported in cpu/8xxx/ddr/ ====================================================== +-------------+---------------------------------------------------------+ | | Rank Interleaving | @@ -56,6 +79,15 @@ The ways to configure the ddr interleaving mode # superbank setenv hwconfig "fsl_ddr:ctlr_intlv=superbank" + # 1KB 3-way interleaving + setenv hwconfig "fsl_ddr:ctlr_intlv=3way_1KB" + + # 4KB 3-way interleaving + setenv hwconfig "fsl_ddr:ctlr_intlv=3way_4KB" + + # 8KB 3-way interleaving + setenv hwconfig "fsl_ddr:ctlr_intlv=3way_8KB" + # disable bank (chip-select) interleaving setenv hwconfig "fsl_ddr:bank_intlv=null" diff --git a/doc/README.pblimage b/doc/README.pblimage new file mode 100644 index 0000000000..2b9bb5c5f5 --- /dev/null +++ b/doc/README.pblimage @@ -0,0 +1,114 @@ +------------------------------------------------------------------ +Freescale PBL(pre-boot loader) Boot Image generation using mkimage +------------------------------------------------------------------ + +The CoreNet SoC's can boot directly from eSPI FLASH, SD/MMC and +NAND, etc. These SoCs use PBL to load RCW and/or pre-initialization +instructions. For more details refer section 5 Pre-boot loader +specifications of reference manual P3041RM/P4080RM/P5020RM at link: +http://www.freescale.com/webapp/search/Serp.jsp?Reference+Manuals + +Building PBL Boot Image and boot steps +-------------------------------------- + +1. Building PBL Boot Image. + The default Image is u-boot.pbl. + + For eSPI boot(available on P3041/P4080/P5020): + To build the eSPI boot image: + make <board_name>_SPIFLASH_config + make u-boot.pbl + + For SD boot(available on P3041/P4080/P5020): + To build the SD boot image: + make <board_name>_SDCARD_config + make u-boot.pbl + + For Nand boot(available on P3041/P5020): + To build the NAND boot image: + make <board_name>_NAND_config + make u-boot.pbl + + +2. pblimage support available with mkimage utility will generate Freescale PBL +boot image that can be flashed on the board eSPI flash, SD/MMC and NAND. +Following steps describe it in detail. + + 1). Boot from eSPI flash + Write u-boot.pbl to eSPI flash from offset 0x0. + for ex in u-boot: + =>tftp 100000 u-boot.pbl + =>sf probe 0 + =>sf erase 0 100000 + =>sf write 100000 0 $filesize + Change SW1[1:5] = off off on off on. + + 2). Boot from SD/MMC + Write u-boot.pbl to SD/MMC from offset 0x1000. + for ex in u-boot: + =>tftp 100000 u-boot.pbl + =>mmcinfo + =>mmc write 100000 8 441 + Change SW1[1:5] = off off on on off. + + 3). Boot from Nand + Write u-boot.pbl to Nand from offset 0x0. + for ex in u-boot: + =>tftp 100000 u-boot.pbl + =>nand info + =>nand erase 0 100000 + =>nand write 100000 0 $filesize + Change SW1[1:5] = off on off off on + Change SW7[1:4] = on off off on + +Board specific configuration file specifications: +------------------------------------------------ +1. Configuration files rcw.cfg and pbi.cfg must present in the +board/freescale/corenet_ds/, rcw.cfg is for RCW, pbi.cfg is for +PBI instructions. File name must not be changed since they are used +in Makefile. +2. These files can have empty lines and lines starting with "#" as first +character to put comments + +Typical example of rcw.cfg file: +----------------------------------- + +#PBL preamble and RCW header +aa55aa55 010e0100 +#64 bytes RCW data +4c580000 00000000 18185218 0000cccc +40464000 3c3c2000 58000000 61000000 +00000000 00000000 00000000 008b6000 +00000000 00000000 00000000 00000000 + +Typical example of pbi.cfg file: +----------------------------------- + +#PBI commands +#Initialize CPC1 +09010000 00200400 +09138000 00000000 +091380c0 00000100 +09010100 00000000 +09010104 fff0000b +09010f00 08000000 +09010000 80000000 +#Configure LAW for CPC1 +09000d00 00000000 +09000d04 fff00000 +09000d08 81000013 +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Initialize eSPI controller +09110000 80000403 +09110020 2d170008 +09110024 00100008 +09110028 00100008 +0911002c 00100008 +#Flush PBL data +09138000 00000000 +091380c0 00000000 + +------------------------------------------------ +Author: Shaohui Xie<Shaohui.Xie@freescale.com> diff --git a/doc/README.srio-boot-corenet b/doc/README.srio-boot-corenet deleted file mode 100644 index 56b094c9a2..0000000000 --- a/doc/README.srio-boot-corenet +++ /dev/null @@ -1,103 +0,0 @@ ------------------------------- -SRIO Boot on Corenet Platforms ------------------------------- - -For some PowerPC processors with SRIO interface, boot location can be configured -to SRIO by RCW. The processor booting from SRIO can do without flash for u-boot -image, ucode and ENV. All the images can be fetched from another processor's -memory space by SRIO link connected between them. - -This document describes the processes based on an example implemented on P4080DS -platforms and a RCW example with boot from SRIO configuration. - -Environment of the SRIO boot: - a) Master and slave can be SOCs in one board or SOCs in separate boards. - b) They are connected with SRIO links, whether 1x or 4x, and directly or - through switch system. - c) Only Master has NorFlash for booting, and all the Master's and Slave's - U-Boot images, UCodes will be stored in this flash. - d) Slave has its own EEPROM for RCW and PBI. - e) Slave's RCW should configure the SerDes for SRIO boot port, set the boot - location to SRIO, and holdoff all the cores if needed. - - ---------- ----------- ----------- - | | | | | | - | | | | | | - | NorFlash|<----->| Master | SRIO | Slave |<---->[EEPROM] - | | | |<===========>| | - | | | | | | - ---------- ----------- ----------- - -The example based on P4080DS platform: - Two P4080DS platforms can be used to implement the boot from SRIO. Their SRIO - ports 0 will be connected directly and will be used for the boot from SRIO. - - 1. Slave's RCW example for boot from SRIO port 0 and core 0 not in holdoff. - 00000000: aa55 aa55 010e 0100 0c58 0000 0000 0000 - 00000010: 1818 1818 0000 8888 7440 4000 0000 2000 - 00000020: f400 0000 0100 0000 0000 0000 0000 0000 - 00000030: 0000 0000 0083 0000 0000 0000 0000 0000 - 00000040: 0000 0000 0000 0000 0813 8040 698b 93fe - - 2. Slave's RCW example for boot from SRIO port 0 and all cores in holdoff. - 00000000: aa55 aa55 010e 0100 0c58 0000 0000 0000 - 00000010: 1818 1818 0000 8888 7440 4000 0000 2000 - 00000020: f440 0000 0100 0000 0000 0000 0000 0000 - 00000030: 0000 0000 0083 0000 0000 0000 0000 0000 - 00000040: 0000 0000 0000 0000 0813 8040 063c 778f - - 3. Sequence in Step by Step. - a) Update RCW for slave with boot from SRIO port 0 configuration. - b) Program slave's U-Boot image, UCode, and ENV parameters into master's - NorFlash. - c) Start up master and it will boot up normally from its NorFlash. - Then, it will finish necessary configurations for slave's boot from - SRIO port 0. - d) Master will set inbound SRIO windows covered slave's U-Boot image stored - in master's NorFlash. - e) Master will set an inbound SRIO window covered slave's UCode stored in - master's NorFlash. - f) Master will set an inbound SRIO window covered slave's ENV stored in - master's NorFlash. - g) If need to release slave's core, master will set outbound SRIO windows - in order to configure slave's registers for the core's releasing. - h) If all cores of slave in holdoff, slave should be powered on before all - the above master's steps, and wait to be released by master. If not all - cores in holdoff, that means core 0 will start up normally, slave should - be powered on after all the above master's steps. In the startup phase - of the slave from SRIO, it will finish some necessary configurations. - i) Slave will set a specific TLB entry for the boot process. - j) Slave will set a LAW entry with the TargetID SRIO port 0 for the boot. - k) Slave will set a specific TLB entry in order to fetch UCode and ENV - from master. - l) Slave will set a LAW entry with the TargetID SRIO port 0 for UCode and ENV. - -How to use this feature: - To use this feature, you need to focus three points. - - 1. Slave's RCW with SRIO boot configurations, and all cores in holdoff - configurations if needed. - Please refer to the examples given above. - - 2. U-Boot image's compilation. - For master, U-Boot image should be generated specifically by - - make xxxx_SRIOBOOT_MASTER_config. - - For example, master U-Boot image used on P4080DS should be compiled with - - make P4080DS_SRIOBOOT_MASTER_config. - - For slave, U-Boot image should be generated specifically by - - make xxxx_SRIOBOOT_SLAVE_config. - - For example, slave U-Boot image used on P4080DS should be compiled with - - make P4080DS_SRIOBOOT_SLAVE_config. - - 3. Necessary modifications based on a specific environment. - For a specific environment, the SRIO port for boot, the addresses of the - slave's U-Boot image, UCode, ENV stored in master's NorFlash, and any other - configurations can be modified in the file: - include/configs/corenet_ds.h. diff --git a/doc/README.srio-pcie-boot-corenet b/doc/README.srio-pcie-boot-corenet new file mode 100644 index 0000000000..cd7e7ee9b3 --- /dev/null +++ b/doc/README.srio-pcie-boot-corenet @@ -0,0 +1,112 @@ +--------------------------------------- +SRIO and PCIE Boot on Corenet Platforms +--------------------------------------- + +For some PowerPC processors with SRIO or PCIE interface, boot location can be +configured to SRIO or PCIE by RCW. The processor booting from SRIO or PCIE can +do without flash for u-boot image, ucode and ENV. All the images can be fetched +from another processor's memory space by SRIO or PCIE link connected between +them. + +This document describes the processes based on an example implemented on P4080DS +platforms and a RCW example with boot from SRIO or PCIE configuration. + +Environment of the SRIO or PCIE boot: + a) Master and slave can be SOCs in one board or SOCs in separate boards. + b) They are connected with SRIO or PCIE links, whether 1x, 2x or 4x, and + directly or through switch system. + c) Only Master has NorFlash for booting, and all the Master's and Slave's + U-Boot images, UCodes will be stored in this flash. + d) Slave has its own EEPROM for RCW and PBI. + e) Slave's RCW should configure the SerDes for SRIO or PCIE boot port, set + the boot location to SRIO or PCIE, and holdoff all the cores. + + ---------- ----------- ----------- + | | | | | | + | | | | | | + | NorFlash|<----->| Master |SRIO or PCIE | Slave |<---->[EEPROM] + | | | |<===========>| | + | | | | | | + ---------- ----------- ----------- + +The example based on P4080DS platform: + Two P4080DS platforms can be used to implement the boot from SRIO or PCIE. + Their SRIO or PCIE ports 1 will be connected directly and will be used for + the boot from SRIO or PCIE. + + 1. Slave's RCW example for boot from SRIO port 1 and all cores in holdoff. + 00000000: aa55 aa55 010e 0100 0c58 0000 0000 0000 + 00000010: 1818 1818 0000 8888 7440 4000 0000 2000 + 00000020: f440 0000 0100 0000 0000 0000 0000 0000 + 00000030: 0000 0000 0083 0000 0000 0000 0000 0000 + 00000040: 0000 0000 0000 0000 0813 8040 063c 778f + + 2. Slave's RCW example for boot from PCIE port 1 and all cores in holdoff. + 00000000: aa55 aa55 010e 0100 0c58 0000 0000 0000 + 00000010: 1818 1818 0000 8888 1440 4000 0000 2000 + 00000020: f040 0000 0100 0000 0020 0000 0000 0000 + 00000030: 0000 0000 0083 0000 0000 0000 0000 0000 + 00000040: 0000 0000 0000 0000 0813 8040 547e ffc9 + + 3. Sequence in Step by Step. + a) Update RCW for slave with boot from SRIO or PCIE port 1 configuration. + b) Program slave's U-Boot image, UCode, and ENV parameters into master's + NorFlash. + c) Set environment variable "bootmaster" to "SRIO1" or "PCIE1" and save + environment for master. + setenv bootmaster SRIO1 + or + setenv bootmaster PCIE1 + saveenv + d) Restart up master and it will boot up normally from its NorFlash. + Then, it will finish necessary configurations for slave's boot from + SRIO or PCIE port 1. + e) Master will set inbound SRIO or PCIE windows covered slave's U-Boot + image stored in master's NorFlash. + f) Master will set an inbound SRIO or PCIE window covered slave's UCode + and ENV stored in master's NorFlash. + g) Master will set outbound SRIO or PCIE windows in order to configure + slave's registers for the core's releasing. + h) Since all cores of slave in holdoff, slave should be powered on before + all the above master's steps, and wait to be released by master. In the + startup phase of the slave from SRIO or PCIE, it will finish some + necessary configurations. + i) Slave will set a specific TLB entry for the boot process. + j) Slave will set a LAW entry with the TargetID SRIO or PCIE port 1 for + the boot. + k) Slave will set a specific TLB entry in order to fetch UCode and ENV + from master. + l) Slave will set a LAW entry with the TargetID SRIO or PCIE port 1 for + UCode and ENV. + +How to use this feature: + To use this feature, you need to focus those points. + + 1. Slave's RCW with SRIO or PCIE boot configurations, and all cores in holdoff + configurations. + Please refer to the examples given above. + + 2. U-Boot image's compilation. + For master, U-Boot image should be generated normally. + + For example, master U-Boot image used on P4080DS should be compiled with + + make P4080DS_config. + + For slave, U-Boot image should be generated specifically by + + make xxxx_SRIO_PCIE_BOOT_config. + + For example, slave U-Boot image used on P4080DS should be compiled with + + make P4080DS_SRIO_PCIE_BOOT_config. + + 3. Necessary modifications based on a specific environment. + For a specific environment, the addresses of the slave's U-Boot image, + UCode, ENV stored in master's NorFlash, and any other configurations + can be modified in the file: + include/configs/corenet_ds.h. + + 4. Set and save the environment variable "bootmaster" with "SRIO1", "SRIO2" + or "PCIE1", "PCIE2", "PCIE3" for master, and then restart it in order to + perform the role as a master for boot from SRIO or PCIE. diff --git a/drivers/misc/fsl_law.c b/drivers/misc/fsl_law.c index a7d04b7ea3..223cd5d65c 100644 --- a/drivers/misc/fsl_law.c +++ b/drivers/misc/fsl_law.c @@ -275,5 +275,59 @@ void init_laws(void) law_table[i].size, law_table[i].trgt_id); } +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE + /* check RCW to get which port is used for boot */ + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + u32 bootloc = in_be32(&gur->rcwsr[6]); + /* + * in SRIO or PCIE boot we need to set specail LAWs for + * SRIO or PCIE interfaces. + */ + switch ((bootloc & FSL_CORENET_RCWSR6_BOOT_LOC) >> 23) { + case 0x0: /* boot from PCIE1 */ + set_next_law(CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS, + LAW_SIZE_1M, + LAW_TRGT_IF_PCIE_1); + set_next_law(CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS, + LAW_SIZE_1M, + LAW_TRGT_IF_PCIE_1); + break; + case 0x1: /* boot from PCIE2 */ + set_next_law(CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS, + LAW_SIZE_1M, + LAW_TRGT_IF_PCIE_2); + set_next_law(CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS, + LAW_SIZE_1M, + LAW_TRGT_IF_PCIE_2); + break; + case 0x2: /* boot from PCIE3 */ + set_next_law(CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS, + LAW_SIZE_1M, + LAW_TRGT_IF_PCIE_3); + set_next_law(CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS, + LAW_SIZE_1M, + LAW_TRGT_IF_PCIE_3); + break; + case 0x8: /* boot from SRIO1 */ + set_next_law(CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS, + LAW_SIZE_1M, + LAW_TRGT_IF_RIO_1); + set_next_law(CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS, + LAW_SIZE_1M, + LAW_TRGT_IF_RIO_1); + break; + case 0x9: /* boot from SRIO2 */ + set_next_law(CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS, + LAW_SIZE_1M, + LAW_TRGT_IF_RIO_2); + set_next_law(CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS, + LAW_SIZE_1M, + LAW_TRGT_IF_RIO_2); + break; + default: + break; + } +#endif + return ; } diff --git a/drivers/net/fm/Makefile b/drivers/net/fm/Makefile index 072b178a04..cc57354755 100644 --- a/drivers/net/fm/Makefile +++ b/drivers/net/fm/Makefile @@ -36,10 +36,8 @@ COBJS-y += tgec_phy.o COBJS-$(CONFIG_P1017) += p1023.o COBJS-$(CONFIG_P1023) += p1023.o # The P204x, P304x, and P5020 are the same -COBJS-$(CONFIG_PPC_P2040) += p5020.o COBJS-$(CONFIG_PPC_P2041) += p5020.o COBJS-$(CONFIG_PPC_P3041) += p5020.o -COBJS-$(CONFIG_PPC_P3060) += p3060.o COBJS-$(CONFIG_PPC_P4080) += p4080.o COBJS-$(CONFIG_PPC_P5020) += p5020.o endif diff --git a/drivers/net/fm/init.c b/drivers/net/fm/init.c index 953c359e6e..736b8b9582 100644 --- a/drivers/net/fm/init.c +++ b/drivers/net/fm/init.c @@ -50,6 +50,9 @@ struct fm_eth_info fm_info[] = { #if (CONFIG_SYS_NUM_FM2_DTSEC >= 4) FM_DTSEC_INFO_INITIALIZER(2, 4), #endif +#if (CONFIG_SYS_NUM_FM2_DTSEC >= 5) + FM_DTSEC_INFO_INITIALIZER(2, 5), +#endif #if (CONFIG_SYS_NUM_FM1_10GEC >= 1) FM_TGEC_INFO_INITIALIZER(1, 1), #endif @@ -152,6 +155,22 @@ void fm_info_set_phy_address(enum fm_port port, int address) } /* + * Returns the PHY address for a given Fman port + * + * The port must be set via a prior call to fm_info_set_phy_address(). + * A negative error code is returned if the port is invalid. + */ +int fm_info_get_phy_address(enum fm_port port) +{ + int i = fm_port_to_index(port); + + if (i == -1) + return -1; + + return fm_info[i].phy_addr; +} + +/* * Returns the type of the data interface between the given MAC and its PHY. * This is typically determined by the RCW. */ @@ -181,7 +200,8 @@ void board_ft_fman_fixup_port(void *blob, char * prop, phys_addr_t pa, static void ft_fixup_port(void *blob, struct fm_eth_info *info, char *prop) { - int off, ph; + int off; + uint32_t ph; phys_addr_t paddr = CONFIG_SYS_CCSRBAR_PHYS + info->compat_offset; u64 dtsec1_addr = (u64)CONFIG_SYS_CCSRBAR_PHYS + CONFIG_SYS_FSL_FM1_DTSEC1_OFFSET; @@ -198,12 +218,10 @@ static void ft_fixup_port(void *blob, struct fm_eth_info *info, char *prop) off = fdt_node_offset_by_compat_reg(blob, prop, paddr); /* Don't disable FM1-DTSEC1 MAC as its used for MDIO */ - if (paddr != dtsec1_addr) { - /* disable the mac node */ - fdt_setprop_string(blob, off, "status", "disabled"); - } + if (paddr != dtsec1_addr) + fdt_status_disabled(blob, off); /* disable the MAC node */ - /* disable the node point to the mac */ + /* disable the fsl,dpa-ethernet node that points to the MAC */ ph = fdt_get_phandle(blob, off); do_fixup_by_prop(blob, "fsl,fman-mac", &ph, sizeof(ph), "status", "disabled", strlen("disabled") + 1, 1); diff --git a/drivers/net/fm/p3060.c b/drivers/net/fm/p3060.c deleted file mode 100644 index c9748a954c..0000000000 --- a/drivers/net/fm/p3060.c +++ /dev/null @@ -1,97 +0,0 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ -#include <common.h> -#include <phy.h> -#include <fm_eth.h> -#include <asm/io.h> -#include <asm/immap_85xx.h> -#include <asm/fsl_serdes.h> - -u32 port_to_devdisr[] = { - [FM1_DTSEC1] = FSL_CORENET_DEVDISR2_DTSEC1_1, - [FM1_DTSEC2] = FSL_CORENET_DEVDISR2_DTSEC1_2, - [FM1_DTSEC3] = FSL_CORENET_DEVDISR2_DTSEC1_3, - [FM1_DTSEC4] = FSL_CORENET_DEVDISR2_DTSEC1_4, - [FM2_DTSEC1] = FSL_CORENET_DEVDISR2_DTSEC2_1, - [FM2_DTSEC2] = FSL_CORENET_DEVDISR2_DTSEC2_2, - [FM2_DTSEC3] = FSL_CORENET_DEVDISR2_DTSEC2_3, - [FM2_DTSEC4] = FSL_CORENET_DEVDISR2_DTSEC2_4, -}; - -static int is_device_disabled(enum fm_port port) -{ - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 devdisr2 = in_be32(&gur->devdisr2); - - return port_to_devdisr[port] & devdisr2; -} - -void fman_disable_port(enum fm_port port) -{ - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - - /* don't allow disabling of DTSEC1 as its needed for MDIO */ - if (port == FM1_DTSEC1) - return; - - setbits_be32(&gur->devdisr2, port_to_devdisr[port]); -} - -phy_interface_t fman_port_enet_if(enum fm_port port) -{ - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 rcwsr11 = in_be32(&gur->rcwsr[11]); - - if (is_device_disabled(port)) - return PHY_INTERFACE_MODE_NONE; - - /* handle RGMII/MII first */ - if ((port == FM1_DTSEC1) && ((rcwsr11 & FSL_CORENET_RCWSR11_EC1) == - FSL_CORENET_RCWSR11_EC1_FM1_DTSEC1)) - return PHY_INTERFACE_MODE_RGMII; - - if ((port == FM1_DTSEC2) && ((rcwsr11 & FSL_CORENET_RCWSR11_EC2) == - FSL_CORENET_RCWSR11_EC2_FM1_DTSEC2)) - return PHY_INTERFACE_MODE_RGMII; - - if ((port == FM2_DTSEC1) && ((rcwsr11 & FSL_CORENET_RCWSR11_EC2) == - FSL_CORENET_RCWSR11_EC2_FM2_DTSEC1)) - return PHY_INTERFACE_MODE_RGMII; - - switch (port) { - case FM1_DTSEC1: - case FM1_DTSEC2: - case FM1_DTSEC3: - case FM1_DTSEC4: - if (is_serdes_configured(SGMII_FM1_DTSEC1 + port - FM1_DTSEC1)) - return PHY_INTERFACE_MODE_SGMII; - break; - case FM2_DTSEC1: - case FM2_DTSEC2: - case FM2_DTSEC3: - case FM2_DTSEC4: - if (is_serdes_configured(SGMII_FM2_DTSEC1 + port - FM2_DTSEC1)) - return PHY_INTERFACE_MODE_SGMII; - break; - default: - return PHY_INTERFACE_MODE_NONE; - } - - return PHY_INTERFACE_MODE_NONE; -} diff --git a/drivers/pci/fsl_pci_init.c b/drivers/pci/fsl_pci_init.c index 1d75a82bc3..0d46c96312 100644 --- a/drivers/pci/fsl_pci_init.c +++ b/drivers/pci/fsl_pci_init.c @@ -211,6 +211,95 @@ static int fsl_pci_setup_inbound_windows(struct pci_controller *hose, return 1; } +#ifdef CONFIG_FSL_CORENET +static void fsl_pcie_boot_master(pit_t *pi) +{ + /* configure inbound window for slave's u-boot image */ + debug("PCIEBOOT - MASTER: Inbound window for slave's image; " + "Local = 0x%llx, Bus = 0x%llx, Size = 0x%x\n", + (u64)CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS, + (u64)CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1, + CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE); + struct pci_region r_inbound; + u32 sz_inbound = __ilog2_u64(CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE) + - 1; + pci_set_region(&r_inbound, + CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1, + CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS, + sz_inbound, + PCI_REGION_MEM | PCI_REGION_SYS_MEMORY); + + set_inbound_window(pi--, &r_inbound, + CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE); + + /* configure inbound window for slave's u-boot image */ + debug("PCIEBOOT - MASTER: Inbound window for slave's image; " + "Local = 0x%llx, Bus = 0x%llx, Size = 0x%x\n", + (u64)CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS, + (u64)CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2, + CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE); + pci_set_region(&r_inbound, + CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2, + CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS, + sz_inbound, + PCI_REGION_MEM | PCI_REGION_SYS_MEMORY); + + set_inbound_window(pi--, &r_inbound, + CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE); + + /* configure inbound window for slave's ucode and ENV */ + debug("PCIEBOOT - MASTER: Inbound window for slave's " + "ucode and ENV; " + "Local = 0x%llx, Bus = 0x%llx, Size = 0x%x\n", + (u64)CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS, + (u64)CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS, + CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE); + sz_inbound = __ilog2_u64(CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE) + - 1; + pci_set_region(&r_inbound, + CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS, + CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS, + sz_inbound, + PCI_REGION_MEM | PCI_REGION_SYS_MEMORY); + + set_inbound_window(pi--, &r_inbound, + CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE); +} + +static void fsl_pcie_boot_master_release_slave(int port) +{ + unsigned long release_addr; + + /* now release slave's core 0 */ + switch (port) { + case 1: + release_addr = CONFIG_SYS_PCIE1_MEM_VIRT + + CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET; + break; + case 2: + release_addr = CONFIG_SYS_PCIE2_MEM_VIRT + + CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET; + break; + case 3: + release_addr = CONFIG_SYS_PCIE3_MEM_VIRT + + CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET; + break; + default: + release_addr = 0; + break; + } + if (release_addr != 0) { + out_be32((void *)release_addr, + CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK); + debug("PCIEBOOT - MASTER: " + "Release slave successfully! Now the slave should start up!\n"); + } else { + debug("PCIEBOOT - MASTER: " + "Release slave failed!\n"); + } +} +#endif + void fsl_pci_init(struct pci_controller *hose, struct fsl_pci_info *pci_info) { u32 cfg_addr = (u32)&((ccsr_fsl_pci_t *)pci_info->regs)->cfg_addr; @@ -295,8 +384,25 @@ void fsl_pci_init(struct pci_controller *hose, struct fsl_pci_info *pci_info) /* see if we are a PCIe or PCI controller */ pci_hose_read_config_byte(hose, dev, FSL_PCIE_CAP_ID, &pcie_cap); +#ifdef CONFIG_FSL_CORENET + /* boot from PCIE --master */ + char *s = getenv("bootmaster"); + char pcie[6]; + sprintf(pcie, "PCIE%d", pci_info->pci_num); + + if (s && (strcmp(s, pcie) == 0)) { + debug("PCIEBOOT - MASTER: Master port [ %d ] for pcie boot.\n", + pci_info->pci_num); + fsl_pcie_boot_master((pit_t *)pi); + } else { + /* inbound */ + inbound = fsl_pci_setup_inbound_windows(hose, + out_lo, pcie_cap, pi); + } +#else /* inbound */ inbound = fsl_pci_setup_inbound_windows(hose, out_lo, pcie_cap, pi); +#endif for (r = 0; r < hose->region_count; r++) debug("PCI reg:%d %016llx:%016llx %016llx %08lx\n", r, @@ -488,6 +594,16 @@ int fsl_pci_init_port(struct fsl_pci_info *pci_info, if (fsl_is_pci_agent(hose)) { fsl_pci_config_unlock(hose); hose->last_busno = hose->first_busno; +#ifdef CONFIG_FSL_CORENET + } else { + /* boot from PCIE --master releases slave's core 0 */ + char *s = getenv("bootmaster"); + char pcie[6]; + sprintf(pcie, "PCIE%d", pci_info->pci_num); + + if (s && (strcmp(s, pcie) == 0)) + fsl_pcie_boot_master_release_slave(pci_info->pci_num); +#endif } pci_hose_read_config_byte(hose, dev, FSL_PCIE_CAP_ID, &pcie_cap); diff --git a/drivers/qe/uec.c b/drivers/qe/uec.c index 216c8982be..e6ae709db7 100644 --- a/drivers/qe/uec.c +++ b/drivers/qe/uec.c @@ -580,8 +580,7 @@ static void phy_change(struct eth_device *dev) { uec_private_t *uec = (uec_private_t *)dev->priv; -#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ - defined(CONFIG_P1021) || defined(CONFIG_P1025) +#if defined(CONFIG_P1012) || defined(CONFIG_P1021) || defined(CONFIG_P1025) ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); /* QE9 and QE12 need to be set for enabling QE MII managment signals */ @@ -592,8 +591,7 @@ static void phy_change(struct eth_device *dev) /* Update the link, speed, duplex */ uec->mii_info->phyinfo->read_status(uec->mii_info); -#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ - defined(CONFIG_P1021) || defined(CONFIG_P1025) +#if defined(CONFIG_P1012) || defined(CONFIG_P1021) || defined(CONFIG_P1025) /* * QE12 is muxed with LBCTL, it needs to be released for enabling * LBCTL signal for LBC usage. @@ -1208,16 +1206,14 @@ static int uec_init(struct eth_device* dev, bd_t *bd) uec_private_t *uec; int err, i; struct phy_info *curphy; -#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ - defined(CONFIG_P1021) || defined(CONFIG_P1025) +#if defined(CONFIG_P1012) || defined(CONFIG_P1021) || defined(CONFIG_P1025) ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); #endif uec = (uec_private_t *)dev->priv; if (uec->the_first_run == 0) { -#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ - defined(CONFIG_P1021) || defined(CONFIG_P1025) +#if defined(CONFIG_P1012) || defined(CONFIG_P1021) || defined(CONFIG_P1025) /* QE9 and QE12 need to be set for enabling QE MII managment signals */ setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE9); setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12); @@ -1249,8 +1245,7 @@ static int uec_init(struct eth_device* dev, bd_t *bd) udelay(100000); } while (1); -#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ - defined(CONFIG_P1021) || defined(CONFIG_P1025) +#if defined(CONFIG_P1012) || defined(CONFIG_P1021) || defined(CONFIG_P1025) /* QE12 needs to be released for enabling LBCTL signal*/ clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12); #endif diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h index 1c0eb74017..31696655bb 100644 --- a/include/configs/P2041RDB.h +++ b/include/configs/P2041RDB.h @@ -22,7 +22,7 @@ /* * P2041 RDB board configuration file - * + * Also supports P2040 RDB */ #ifndef __CONFIG_H #define __CONFIG_H @@ -36,6 +36,15 @@ #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc #endif +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE +/* Set 1M boot space */ +#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) +#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ + (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_SYS_NO_FLASH +#endif + /* High Level Configuration Options */ #define CONFIG_BOOKE #define CONFIG_E500 /* BOOKE e500 family */ @@ -73,7 +82,7 @@ #define CONFIG_ENV_OVERWRITE #ifdef CONFIG_SYS_NO_FLASH -#ifndef CONFIG_RAMBOOT_PBL +#if !defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) #define CONFIG_ENV_IS_NOWHERE #endif #else @@ -104,8 +113,12 @@ #define CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE #define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) +#define CONFIG_ENV_IS_IN_REMOTE +#define CONFIG_ENV_ADDR 0xffe20000 +#define CONFIG_ENV_SIZE 0x2000 #elif defined(CONFIG_ENV_IS_NOWHERE) - #define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SIZE 0x2000 #else #define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ @@ -374,6 +387,35 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ /* + * for slave u-boot IMAGE instored in master memory space, + * PHYS must be aligned based on the SIZE + */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull +/* + * for slave UCODE and ENV instored in master memory space, + * PHYS must be aligned based on the SIZE + */ +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ + +/* slave core release by master*/ +#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 +#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ + +/* + * SRIO_PCIE_BOOT - SLAVE + */ +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE +#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 +#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ + (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) +#endif + +/* * eSPI - Enhanced SPI */ #define CONFIG_FSL_ESPI @@ -485,6 +527,16 @@ unsigned long get_board_sys_clk(unsigned long dummy); #elif defined(CONFIG_NAND) #define CONFIG_SYS_QE_FMAN_FW_IN_NAND #define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) +/* + * Slave has no ucode locally, it can fetch this from remote. When implementing + * in two corenet boards, slave's ucode could be stored in master's memory + * space, the address can be mapped from slave TLB->slave LAW-> + * slave SRIO or PCIE outbound window->master inbound window-> + * master LAW->the ucode address in master's memory space. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000 #else #define CONFIG_SYS_QE_FMAN_FW_IN_NOR #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEF000000 diff --git a/include/configs/P3060QDS.h b/include/configs/P3060QDS.h deleted file mode 100644 index 8006547000..0000000000 --- a/include/configs/P3060QDS.h +++ /dev/null @@ -1,48 +0,0 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * P3060 QDS board configuration file - */ -#define CONFIG_P3060QDS -#define CONFIG_PHYS_64BIT -#define CONFIG_PPC_P3060 -#define CONFIG_FSL_QIXIS - -#define CONFIG_NAND_FSL_ELBC - -#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ - -#define CONFIG_SPI_FLASH_ATMEL -#define CONFIG_SPI_FLASH_EON -#define CONFIG_SPI_FLASH_SST - -#include "corenet_ds.h" - -#define SGMII_CARD_PORT1_PHY_ADDR 0x1C -#define SGMII_CARD_PORT2_PHY_ADDR 0x1D -#define SGMII_CARD_PORT3_PHY_ADDR 0x1E -#define SGMII_CARD_PORT4_PHY_ADDR 0x1F - -/* There is a PCA9547 8-channel I2C-bus multiplexer on P3060QDS board */ -#define CONFIG_I2C_MUX -#define CONFIG_I2C_MULTI_BUS diff --git a/include/configs/P4080DS.h b/include/configs/P4080DS.h index 4a2e47513d..d6f2f5ceb8 100644 --- a/include/configs/P4080DS.h +++ b/include/configs/P4080DS.h @@ -22,6 +22,7 @@ /* * P4080 DS board configuration file + * Also supports P4040 DS */ #define CONFIG_P4080DS #define CONFIG_PHYS_64BIT diff --git a/include/configs/P5020DS.h b/include/configs/P5020DS.h index 4afc4f16ed..8625f76290 100644 --- a/include/configs/P5020DS.h +++ b/include/configs/P5020DS.h @@ -22,7 +22,7 @@ /* * P5020 DS board configuration file - * + * Also supports P5010 DS */ #define CONFIG_P5020DS #define CONFIG_PHYS_64BIT diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index f8f7a82aa9..f4f9bd12a4 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -31,13 +31,21 @@ #ifdef CONFIG_RAMBOOT_PBL #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/corenet_ds/pbi.cfg +#if defined(CONFIG_P3041DS) +#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/corenet_ds/rcw_p3041ds.cfg +#elif defined(CONFIG_P4080DS) +#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/corenet_ds/rcw_p4080ds.cfg +#elif defined(CONFIG_P5020DS) +#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/corenet_ds/rcw_p5020ds.cfg +#endif #endif -#ifdef CONFIG_SRIOBOOT_SLAVE +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE /* Set 1M boot space */ -#define CONFIG_SYS_SRIOBOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) -#define CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS \ - (0x300000000ull | CONFIG_SYS_SRIOBOOT_SLAVE_ADDR) +#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) +#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ + (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc #define CONFIG_SYS_NO_FLASH #endif @@ -77,7 +85,7 @@ #define CONFIG_ENV_OVERWRITE #ifdef CONFIG_SYS_NO_FLASH -#if !defined(CONFIG_SRIOBOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL) +#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL) #define CONFIG_ENV_IS_NOWHERE #endif #else @@ -108,7 +116,7 @@ #define CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE #define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) -#elif defined(CONFIG_SRIOBOOT_SLAVE) +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) #define CONFIG_ENV_IS_IN_REMOTE #define CONFIG_ENV_ADDR 0xffe20000 #define CONFIG_ENV_SIZE 0x2000 @@ -186,11 +194,7 @@ #define CONFIG_DDR_SPD #define CONFIG_FSL_DDR3 -#ifdef CONFIG_P3060QDS -#define CONFIG_SYS_SPD_BUS_NUM 0 -#else #define CONFIG_SYS_SPD_BUS_NUM 1 -#endif #define SPD_EEPROM_ADDRESS1 0x51 #define SPD_EEPROM_ADDRESS2 0x52 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */ @@ -389,51 +393,32 @@ #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ /* - * SRIOBOOT - MASTER - */ -#ifdef CONFIG_SRIOBOOT_MASTER -/* master port for srioboot*/ -#define CONFIG_SRIOBOOT_MASTER_PORT 0 -/* #define CONFIG_SRIOBOOT_MASTER_PORT 1 */ -/* * for slave u-boot IMAGE instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS1 0xfef080000ull -#define CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS1 0xfff80000ull -#define CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE 0x80000 /* 512K */ -#define CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS2 0xfef080000ull -#define CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS2 0x3fff80000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull /* - * for slave UCODE instored in master memory space, + * for slave UCODE and ENV instored in master memory space, * PHYS must be aligned based on the SIZE */ -#define CONFIG_SRIOBOOT_SLAVE_UCODE_LAW_PHYS 0xfef020000ull -#define CONFIG_SRIOBOOT_SLAVE_UCODE_SRIO_PHYS 0x3ffe00000ull -#define CONFIG_SRIOBOOT_SLAVE_UCODE_SIZE 0x10000 /* 64K */ -/* - * for slave ENV instored in master memory space, - * PHYS must be aligned based on the SIZE - */ -#define CONFIG_SRIOBOOT_SLAVE_ENV_LAW_PHYS 0xfef060000ull -#define CONFIG_SRIOBOOT_SLAVE_ENV_SRIO_PHYS 0x3ffe20000ull -#define CONFIG_SRIOBOOT_SLAVE_ENV_SIZE 0x20000 /* 128K */ +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ + /* slave core release by master*/ -#define CONFIG_SRIOBOOT_SLAVE_HOLDOFF -#define CONFIG_SRIOBOOT_SLAVE_BRR_OFFSET 0xe00e4 -#define CONFIG_SRIOBOOT_SLAVE_RELEASE_MASK 0x00000001 /* release core 0 */ -#endif +#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 +#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ /* - * SRIOBOOT - SLAVE + * SRIO_PCIE_BOOT - SLAVE */ -#ifdef CONFIG_SRIOBOOT_SLAVE -/* slave port for srioboot */ -#define CONFIG_SRIOBOOT_SLAVE_PORT0 -/* #define CONFIG_SRIOBOOT_SLAVE_PORT1 */ -#define CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR 0xFFE00000 -#define CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS \ - (0x300000000ull | CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR) +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE +#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 +#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ + (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) #endif /* @@ -556,13 +541,13 @@ #elif defined(CONFIG_NAND) #define CONFIG_SYS_QE_FMAN_FW_IN_NAND #define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) -#elif defined(CONFIG_SRIOBOOT_SLAVE) +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) /* * Slave has no ucode locally, it can fetch this from remote. When implementing * in two corenet boards, slave's ucode could be stored in master's memory * space, the address can be mapped from slave TLB->slave LAW-> - * slave SRIO outbound window->master inbound window->master LAW-> - * the ucode address in master's NOR flash. + * slave SRIO or PCIE outbound window->master inbound window-> + * master LAW->the ucode address in master's memory space. */ #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000 @@ -724,7 +709,7 @@ #define CONFIG_BAUDRATE 115200 -#if defined(CONFIG_P4080DS) || defined(CONFIG_P3060QDS) +#ifdef CONFIG_P4080DS #define __USB_PHY_TYPE ulpi #else #define __USB_PHY_TYPE utmi diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h index a8882d49da..b18f4a0ec5 100644 --- a/include/configs/p1_p2_rdb_pc.h +++ b/include/configs/p1_p2_rdb_pc.h @@ -31,7 +31,7 @@ #endif #if defined(CONFIG_P1020MBG) -#define CONFIG_BOARDNAME "P1020MBG" +#define CONFIG_BOARDNAME "P1020MBG-PC" #define CONFIG_P1020 #define CONFIG_VSC7385_ENET #define CONFIG_SLIC @@ -41,7 +41,7 @@ #endif #if defined(CONFIG_P1020UTM) -#define CONFIG_BOARDNAME "P1020UTM" +#define CONFIG_BOARDNAME "P1020UTM-PC" #define CONFIG_P1020 #define __SW_BOOT_MASK 0x03 #define __SW_BOOT_NOR 0xe0 @@ -49,7 +49,7 @@ #endif #if defined(CONFIG_P1020RDB) -#define CONFIG_BOARDNAME "P1020RDB" +#define CONFIG_BOARDNAME "P1020RDB-PC" #define CONFIG_NAND_FSL_ELBC #define CONFIG_P1020 #define CONFIG_SPI_FLASH @@ -64,7 +64,7 @@ #endif #if defined(CONFIG_P1021RDB) -#define CONFIG_BOARDNAME "P1021RDB" +#define CONFIG_BOARDNAME "P1021RDB-PC" #define CONFIG_NAND_FSL_ELBC #define CONFIG_P1021 #define CONFIG_QE @@ -111,7 +111,7 @@ #endif #if defined(CONFIG_P2020RDB) -#define CONFIG_BOARDNAME "P2020RDB" +#define CONFIG_BOARDNAME "P2020RDB-PCA" #define CONFIG_NAND_FSL_ELBC #define CONFIG_P2020 #define CONFIG_SPI_FLASH diff --git a/include/ddr_spd.h b/include/ddr_spd.h index a9230b9108..9e74d8729e 100644 --- a/include/ddr_spd.h +++ b/include/ddr_spd.h @@ -221,7 +221,12 @@ typedef struct ddr3_spd_eeprom_s { unsigned char therm_ref_opt; /* 31 SDRAM Thermal and Refresh Opts */ unsigned char therm_sensor; /* 32 Module Thermal Sensor */ unsigned char device_type; /* 33 SDRAM device type */ - unsigned char res_34_59[26]; /* 34-59 Reserved, General Section */ + int8_t fine_tCK_min; /* 34 Fine offset for tCKmin */ + int8_t fine_tAA_min; /* 35 Fine offset for tAAmin */ + int8_t fine_tRCD_min; /* 36 Fine offset for tRCDmin */ + int8_t fine_tRP_min; /* 37 Fine offset for tRPmin */ + int8_t fine_tRC_min; /* 38 Fine offset for tRCmin */ + unsigned char res_39_59[21]; /* 39-59 Reserved, General Section */ /* Module-Specific Section: Bytes 60-116 */ union { diff --git a/include/fm_eth.h b/include/fm_eth.h index c7c68820d5..e56541df1b 100644 --- a/include/fm_eth.h +++ b/include/fm_eth.h @@ -35,6 +35,7 @@ enum fm_port { FM2_DTSEC2, FM2_DTSEC3, FM2_DTSEC4, + FM2_DTSEC5, FM2_10GEC1, NUM_FM_PORTS, }; @@ -109,6 +110,7 @@ void fman_enet_init(void); void fdt_fixup_fman_ethernet(void *fdt); phy_interface_t fm_info_get_enet_if(enum fm_port port); void fm_info_set_phy_address(enum fm_port port, int address); +int fm_info_get_phy_address(enum fm_port port); void fm_info_set_mdio(enum fm_port port, struct mii_dev *bus); void fm_disable_port(enum fm_port port); diff --git a/include/image.h b/include/image.h index aa9daa2deb..e5f6649291 100644 --- a/include/image.h +++ b/include/image.h @@ -164,6 +164,7 @@ #define IH_TYPE_OMAPIMAGE 12 /* TI OMAP Config Header Image */ #define IH_TYPE_AISIMAGE 13 /* TI Davinci AIS Image */ #define IH_TYPE_KERNEL_NOLOAD 14 /* OS Kernel Image, can run from any load address */ +#define IH_TYPE_PBLIMAGE 15 /* Freescale PBL Boot Image */ /* * Compression Types diff --git a/nand_spl/board/freescale/common.c b/nand_spl/board/freescale/common.c new file mode 100644 index 0000000000..0e099bc7c6 --- /dev/null +++ b/nand_spl/board/freescale/common.c @@ -0,0 +1,40 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * Author: Matthew McClintock <msm@freescale.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include <common.h> +#include <asm/processor.h> +#include <asm/global_data.h> + +DECLARE_GLOBAL_DATA_PTR; + +#ifndef CONFIG_SYS_FSL_TBCLK_DIV +#define CONFIG_SYS_FSL_TBCLK_DIV 8 +#endif + +void udelay(unsigned long usec) +{ + u32 ticks_per_usec = gd->bus_clk / (CONFIG_SYS_FSL_TBCLK_DIV * 1000000); + u32 ticks = ticks_per_usec * usec; + u32 s = mfspr(SPRN_TBRL); + + while ((mfspr(SPRN_TBRL) - s) < ticks); +} diff --git a/nand_spl/board/freescale/p1010rdb/Makefile b/nand_spl/board/freescale/p1010rdb/Makefile index 8d240eadd9..cdbd49292c 100644 --- a/nand_spl/board/freescale/p1010rdb/Makefile +++ b/nand_spl/board/freescale/p1010rdb/Makefile @@ -39,7 +39,8 @@ CFLAGS += -DCONFIG_NAND_SPL SOBJS = start.o resetvec.o ticks.o COBJS = cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o \ - nand_boot.o nand_boot_fsl_ifc.o ns16550.o tlb.o tlb_table.o + nand_boot.o nand_boot_fsl_ifc.o ns16550.o tlb.o tlb_table.o \ + ../common.o SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) @@ -123,6 +124,9 @@ ifneq ($(OBJTREE), $(SRCTREE)) $(obj)nand_boot.c: @rm -f $(obj)nand_boot.c ln -s $(SRCTREE)/nand_spl/board/$(BOARDDIR)/nand_boot.c $(obj)nand_boot.c +$(obj)../common.c: + @rm -f $(obj)../common.c + ln -s $(SRCTREE)/nand_spl/board/freescale/common.c $(obj)../common.c endif ######################################################################### diff --git a/nand_spl/board/freescale/p1010rdb/nand_boot.c b/nand_spl/board/freescale/p1010rdb/nand_boot.c index 16eeb61d85..9c356901b1 100644 --- a/nand_spl/board/freescale/p1010rdb/nand_boot.c +++ b/nand_spl/board/freescale/p1010rdb/nand_boot.c @@ -27,51 +27,61 @@ #include <asm/immap_85xx.h> #include <asm/fsl_ddr_sdram.h> #include <asm/fsl_law.h> +#include <asm/global_data.h> -#define udelay(x) { int j; for (j = 0; j < x * 10000; j++) isync(); } +DECLARE_GLOBAL_DATA_PTR; unsigned long ddr_freq_mhz; void sdram_init(void) { ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR; + /* mask off E bit */ + u32 svr = SVR_SOC_VER(mfspr(SPRN_SVR)); - out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | SDRAM_CFG_32_BE); - out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS); - out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG); - out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL_2); - out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT); + __raw_writel(CONFIG_SYS_DDR_CONTROL | SDRAM_CFG_32_BE, &ddr->sdram_cfg); + __raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds); + __raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config); + __raw_writel(CONFIG_SYS_DDR_CONTROL_2, &ddr->sdram_cfg_2); + __raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init); if (ddr_freq_mhz < 700) { - out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3_667); - out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0_667); - out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1_667); - out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2_667); - out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1_667); - out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2_667); - out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL_667); - out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL_667); - out_be32(&ddr->ddr_wrlvl_cntl, - CONFIG_SYS_DDR_WRLVL_CONTROL_667); + __raw_writel(CONFIG_SYS_DDR_TIMING_3_667, &ddr->timing_cfg_3); + __raw_writel(CONFIG_SYS_DDR_TIMING_0_667, &ddr->timing_cfg_0); + __raw_writel(CONFIG_SYS_DDR_TIMING_1_667, &ddr->timing_cfg_1); + __raw_writel(CONFIG_SYS_DDR_TIMING_2_667, &ddr->timing_cfg_2); + __raw_writel(CONFIG_SYS_DDR_MODE_1_667, &ddr->sdram_mode); + __raw_writel(CONFIG_SYS_DDR_MODE_2_667, &ddr->sdram_mode_2); + __raw_writel(CONFIG_SYS_DDR_INTERVAL_667, &ddr->sdram_interval); + __raw_writel(CONFIG_SYS_DDR_CLK_CTRL_667, &ddr->sdram_clk_cntl); + __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL_667, &ddr->ddr_wrlvl_cntl); } else { - out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3_800); - out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0_800); - out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1_800); - out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2_800); - out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1_800); - out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2_800); - out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL_800); - out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL_800); - out_be32(&ddr->ddr_wrlvl_cntl, - CONFIG_SYS_DDR_WRLVL_CONTROL_800); + __raw_writel(CONFIG_SYS_DDR_TIMING_3_800, &ddr->timing_cfg_3); + __raw_writel(CONFIG_SYS_DDR_TIMING_0_800, &ddr->timing_cfg_0); + __raw_writel(CONFIG_SYS_DDR_TIMING_1_800, &ddr->timing_cfg_1); + __raw_writel(CONFIG_SYS_DDR_TIMING_2_800, &ddr->timing_cfg_2); + __raw_writel(CONFIG_SYS_DDR_MODE_1_800, &ddr->sdram_mode); + __raw_writel(CONFIG_SYS_DDR_MODE_2_800, &ddr->sdram_mode_2); + __raw_writel(CONFIG_SYS_DDR_INTERVAL_800, &ddr->sdram_interval); + __raw_writel(CONFIG_SYS_DDR_CLK_CTRL_800, &ddr->sdram_clk_cntl); + __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL_800, &ddr->ddr_wrlvl_cntl); } - out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4); - out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5); - out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CONTROL); + __raw_writel(CONFIG_SYS_DDR_TIMING_4, &ddr->timing_cfg_4); + __raw_writel(CONFIG_SYS_DDR_TIMING_5, &ddr->timing_cfg_5); + __raw_writel(CONFIG_SYS_DDR_ZQ_CONTROL, &ddr->ddr_zq_cntl); + + /* P1014 and it's derivatives support max 16bit DDR width */ + if (svr == SVR_P1014) { + __raw_writel(ddr->sdram_cfg & ~SDRAM_CFG_DBW_MASK, &ddr->sdram_cfg); + __raw_writel(ddr->sdram_cfg | SDRAM_CFG_16_BE, &ddr->sdram_cfg); + /* For CS0_BNDS we divide the start and end address by 2, so we can just + * shift the entire register to achieve the desired result and the mask + * the value so we don't write reserved fields */ + __raw_writel((CONFIG_SYS_DDR_CS0_BNDS >> 1) & 0x0fff0fff, &ddr->cs0_bnds); + } - /* mimic 500us delay, with busy isync() loop */ - udelay(100); + udelay(500); /* Let the controller go */ out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN); @@ -82,20 +92,19 @@ void sdram_init(void) void board_init_f(ulong bootflag) { u32 plat_ratio, ddr_ratio; - unsigned long bus_clk; ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; /* initialize selected port with appropriate baud rate */ plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; plat_ratio >>= 1; - bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; + gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; ddr_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_DDR_RATIO; ddr_ratio = ddr_ratio >> MPC85xx_PORPLLSR_DDR_RATIO_SHIFT; ddr_freq_mhz = (CONFIG_SYS_CLK_FREQ * ddr_ratio) / 0x1000000; NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, - bus_clk / 16 / CONFIG_BAUDRATE); + gd->bus_clk / 16 / CONFIG_BAUDRATE); puts("\nNAND boot... "); diff --git a/nand_spl/board/freescale/p1023rds/Makefile b/nand_spl/board/freescale/p1023rds/Makefile index 168e868641..da435213fc 100644 --- a/nand_spl/board/freescale/p1023rds/Makefile +++ b/nand_spl/board/freescale/p1023rds/Makefile @@ -34,7 +34,8 @@ CFLAGS += -DCONFIG_NAND_SPL SOBJS = start.o resetvec.o COBJS = cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o \ - nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o + nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o \ + ../common.o SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) @@ -114,6 +115,9 @@ ifneq ($(OBJTREE), $(SRCTREE)) $(obj)nand_boot.c: @rm -f $(obj)nand_boot.c ln -s $(SRCTREE)/nand_spl/board/$(BOARDDIR)/nand_boot.c $(obj)nand_boot.c +$(obj)../common.c: + @rm -f $(obj)../common.c + ln -s $(SRCTREE)/nand_spl/board/freescale/common.c $(obj)../common.c endif ######################################################################### diff --git a/nand_spl/board/freescale/p1023rds/nand_boot.c b/nand_spl/board/freescale/p1023rds/nand_boot.c index 0065c876de..89e339d512 100644 --- a/nand_spl/board/freescale/p1023rds/nand_boot.c +++ b/nand_spl/board/freescale/p1023rds/nand_boot.c @@ -25,6 +25,10 @@ #include <asm/io.h> #include <nand.h> #include <asm/fsl_law.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/global_data.h> + +DECLARE_GLOBAL_DATA_PTR; /* Fixed sdram init -- doesn't use serial presence detect. */ void sdram_init(void) @@ -33,40 +37,47 @@ void sdram_init(void) set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1); - out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS); - out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG); - out_be32(&ddr->cs1_bnds, CONFIG_SYS_DDR_CS1_BNDS); - out_be32(&ddr->cs1_config, CONFIG_SYS_DDR_CS1_CONFIG); - out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3); - out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0); - out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1); - out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2); - out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL2); - out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1); - out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2); - out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL); - out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT); - out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL); - out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4); - out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5); - out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL); - out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL); - out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1); - out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_2); - out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL); + __raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds); + __raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config); + __raw_writel(CONFIG_SYS_DDR_CS1_BNDS, &ddr->cs1_bnds); + __raw_writel(CONFIG_SYS_DDR_CS1_CONFIG, &ddr->cs1_config); + __raw_writel(CONFIG_SYS_DDR_TIMING_3, &ddr->timing_cfg_3); + __raw_writel(CONFIG_SYS_DDR_TIMING_0, &ddr->timing_cfg_0); + __raw_writel(CONFIG_SYS_DDR_TIMING_1, &ddr->timing_cfg_1); + __raw_writel(CONFIG_SYS_DDR_TIMING_2, &ddr->timing_cfg_2); + __raw_writel(CONFIG_SYS_DDR_CONTROL2, &ddr->sdram_cfg_2); + __raw_writel(CONFIG_SYS_DDR_MODE_1, &ddr->sdram_mode); + __raw_writel(CONFIG_SYS_DDR_MODE_2, &ddr->sdram_mode_2); + __raw_writel(CONFIG_SYS_DDR_INTERVAL, &ddr->sdram_interval); + __raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init); + __raw_writel(CONFIG_SYS_DDR_CLK_CTRL, &ddr->sdram_clk_cntl); + __raw_writel(CONFIG_SYS_DDR_TIMING_4, &ddr->timing_cfg_4); + __raw_writel(CONFIG_SYS_DDR_TIMING_5, &ddr->timing_cfg_5); + __raw_writel(CONFIG_SYS_DDR_ZQ_CNTL, &ddr->ddr_zq_cntl); + __raw_writel(CONFIG_SYS_DDR_WRLVL_CNTL, &ddr->ddr_wrlvl_cntl); + __raw_writel(CONFIG_SYS_DDR_CDR_1, &ddr->ddr_cdr1); + __raw_writel(CONFIG_SYS_DDR_CDR_2, &ddr->ddr_cdr2); + /* Set, but do not enable the memory */ + __raw_writel(CONFIG_SYS_DDR_CONTROL & ~SDRAM_CFG_MEM_EN, &ddr->sdram_cfg); + + asm volatile("sync;isync"); + udelay(500); + + /* Let the controller go */ + out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN); } void board_init_f(ulong bootflag) { - u32 plat_ratio, bus_clk; + u32 plat_ratio; ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; /* initialize selected port with appropriate baud rate */ plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; plat_ratio >>= 1; - bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; + gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, - bus_clk / 16 / CONFIG_BAUDRATE); + gd->bus_clk / 16 / CONFIG_BAUDRATE); puts("\nNAND boot... "); /* Initialize the DDR3 */ diff --git a/nand_spl/board/freescale/p1_p2_rdb_pc/Makefile b/nand_spl/board/freescale/p1_p2_rdb_pc/Makefile index 475cc496b3..46cf7099b6 100644 --- a/nand_spl/board/freescale/p1_p2_rdb_pc/Makefile +++ b/nand_spl/board/freescale/p1_p2_rdb_pc/Makefile @@ -39,7 +39,8 @@ CFLAGS += -DCONFIG_NAND_SPL SOBJS = start.o resetvec.o COBJS = cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o \ - nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o + nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o \ + ../common.o SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) @@ -119,6 +120,9 @@ ifneq ($(OBJTREE), $(SRCTREE)) $(obj)nand_boot.c: @rm -f $(obj)nand_boot.c ln -s $(SRCTREE)/nand_spl/board/$(BOARDDIR)/nand_boot.c $(obj)nand_boot.c +$(obj)../common.c: + @rm -f $(obj)../common.c + ln -s $(SRCTREE)/nand_spl/board/freescale/common.c $(obj)../common.c endif ######################################################################### diff --git a/nand_spl/board/freescale/p1_p2_rdb_pc/nand_boot.c b/nand_spl/board/freescale/p1_p2_rdb_pc/nand_boot.c index b9796ea6c9..4c140c1572 100644 --- a/nand_spl/board/freescale/p1_p2_rdb_pc/nand_boot.c +++ b/nand_spl/board/freescale/p1_p2_rdb_pc/nand_boot.c @@ -25,11 +25,9 @@ #include <nand.h> #include <asm/fsl_law.h> #include <asm/fsl_ddr_sdram.h> +#include <asm/global_data.h> -#define udelay(x) {int i, j; \ - for (i = 0; i < x; i++) \ - for (j = 0; j < 10000; j++) \ - ; } +DECLARE_GLOBAL_DATA_PTR; /* * Fixed sdram init -- doesn't use serial presence detect. @@ -38,32 +36,32 @@ void sdram_init(void) { ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR; - out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS); - out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG); + __raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds); + __raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config); #if CONFIG_CHIP_SELECTS_PER_CTRL > 1 - out_be32(&ddr->cs1_bnds, CONFIG_SYS_DDR_CS1_BNDS); - out_be32(&ddr->cs1_config, CONFIG_SYS_DDR_CS1_CONFIG); + __raw_writel(CONFIG_SYS_DDR_CS1_BNDS, &ddr->cs1_bnds); + __raw_writel(CONFIG_SYS_DDR_CS1_CONFIG, &ddr->cs1_config); #endif - out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3); - out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0); - out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1); - out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2); + __raw_writel(CONFIG_SYS_DDR_TIMING_3, &ddr->timing_cfg_3); + __raw_writel(CONFIG_SYS_DDR_TIMING_0, &ddr->timing_cfg_0); + __raw_writel(CONFIG_SYS_DDR_TIMING_1, &ddr->timing_cfg_1); + __raw_writel(CONFIG_SYS_DDR_TIMING_2, &ddr->timing_cfg_2); - out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL_2); - out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1); - out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2); + __raw_writel(CONFIG_SYS_DDR_CONTROL_2, &ddr->sdram_cfg_2); + __raw_writel(CONFIG_SYS_DDR_MODE_1, &ddr->sdram_mode); + __raw_writel(CONFIG_SYS_DDR_MODE_2, &ddr->sdram_mode_2); - out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL); - out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT); - out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL); + __raw_writel(CONFIG_SYS_DDR_INTERVAL, &ddr->sdram_interval); + __raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init); + __raw_writel(CONFIG_SYS_DDR_CLK_CTRL, &ddr->sdram_clk_cntl); - out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4); - out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5); - out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CONTROL); - out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CONTROL); + __raw_writel(CONFIG_SYS_DDR_TIMING_4, &ddr->timing_cfg_4); + __raw_writel(CONFIG_SYS_DDR_TIMING_5, &ddr->timing_cfg_5); + __raw_writel(CONFIG_SYS_DDR_ZQ_CONTROL, &ddr->ddr_zq_cntl); + __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL, &ddr->ddr_wrlvl_cntl); /* Set, but do not enable the memory */ - out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL & ~SDRAM_CFG_MEM_EN); + __raw_writel(CONFIG_SYS_DDR_CONTROL & ~SDRAM_CFG_MEM_EN, &ddr->sdram_cfg); asm volatile("sync;isync"); udelay(500); @@ -76,7 +74,7 @@ void sdram_init(void) void board_init_f(ulong bootflag) { - u32 plat_ratio, bus_clk; + u32 plat_ratio; ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; #ifndef CONFIG_QE ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR); @@ -85,22 +83,22 @@ void board_init_f(ulong bootflag) /* initialize selected port with appropriate baud rate */ plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; plat_ratio >>= 1; - bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; + gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, - bus_clk / 16 / CONFIG_BAUDRATE); + gd->bus_clk / 16 / CONFIG_BAUDRATE); puts("\nNAND boot... "); #ifndef CONFIG_QE /* init DDR3 reset signal */ - out_be32(&pgpio->gpdir, 0x02000000); - out_be32(&pgpio->gpodr, 0x00200000); - out_be32(&pgpio->gpdat, 0x00000000); + __raw_writel(0x02000000, &pgpio->gpdir); + __raw_writel(0x00200000, &pgpio->gpodr); + __raw_writel(0x00000000, &pgpio->gpdat); udelay(1000); - out_be32(&pgpio->gpdat, 0x00200000); + __raw_writel(0x00200000, &pgpio->gpdat); udelay(1000); - out_be32(&pgpio->gpdir, 0x00000000); + __raw_writel(0x00000000, &pgpio->gpdir); #endif /* Initialize the DDR3 */ diff --git a/nand_spl/nand_boot_fsl_elbc.c b/nand_spl/nand_boot_fsl_elbc.c index 502605b1d5..e9d649743e 100644 --- a/nand_spl/nand_boot_fsl_elbc.c +++ b/nand_spl/nand_boot_fsl_elbc.c @@ -66,39 +66,42 @@ static void nand_load(unsigned int offs, int uboot_size, uchar *dst) if (large) { fmr |= FMR_ECCM; - out_be32(®s->fcr, (NAND_CMD_READ0 << FCR_CMD0_SHIFT) | - (NAND_CMD_READSTART << FCR_CMD1_SHIFT)); - out_be32(®s->fir, - (FIR_OP_CW0 << FIR_OP0_SHIFT) | - (FIR_OP_CA << FIR_OP1_SHIFT) | - (FIR_OP_PA << FIR_OP2_SHIFT) | - (FIR_OP_CW1 << FIR_OP3_SHIFT) | - (FIR_OP_RBW << FIR_OP4_SHIFT)); + __raw_writel((NAND_CMD_READ0 << FCR_CMD0_SHIFT) | + (NAND_CMD_READSTART << FCR_CMD1_SHIFT), + ®s->fcr); + __raw_writel( + (FIR_OP_CW0 << FIR_OP0_SHIFT) | + (FIR_OP_CA << FIR_OP1_SHIFT) | + (FIR_OP_PA << FIR_OP2_SHIFT) | + (FIR_OP_CW1 << FIR_OP3_SHIFT) | + (FIR_OP_RBW << FIR_OP4_SHIFT), + ®s->fir); } else { - out_be32(®s->fcr, NAND_CMD_READ0 << FCR_CMD0_SHIFT); - out_be32(®s->fir, - (FIR_OP_CW0 << FIR_OP0_SHIFT) | - (FIR_OP_CA << FIR_OP1_SHIFT) | - (FIR_OP_PA << FIR_OP2_SHIFT) | - (FIR_OP_RBW << FIR_OP3_SHIFT)); + __raw_writel(NAND_CMD_READ0 << FCR_CMD0_SHIFT, ®s->fcr); + __raw_writel( + (FIR_OP_CW0 << FIR_OP0_SHIFT) | + (FIR_OP_CA << FIR_OP1_SHIFT) | + (FIR_OP_PA << FIR_OP2_SHIFT) | + (FIR_OP_RBW << FIR_OP3_SHIFT), + ®s->fir); } - out_be32(®s->fbcr, 0); - clrsetbits_be32(®s->bank[0].br, BR_DECC, BR_DECC_CHK_GEN); + __raw_writel(0, ®s->fbcr); while (pos < uboot_size) { int i = 0; - out_be32(®s->fbar, offs >> block_shift); + __raw_writel(offs >> block_shift, ®s->fbar); do { int j; unsigned int page_offs = (offs & (block_size - 1)) << 1; - out_be32(®s->ltesr, ~0); - out_be32(®s->lteatr, 0); - out_be32(®s->fpar, page_offs); - out_be32(®s->fmr, fmr); - out_be32(®s->lsor, 0); + __raw_writel(~0, ®s->ltesr); + __raw_writel(0, ®s->lteatr); + __raw_writel(page_offs, ®s->fpar); + __raw_writel(fmr, ®s->fmr); + sync(); + __raw_writel(0, ®s->lsor); nand_wait(); page_offs %= WINDOW_SIZE; diff --git a/tools/Makefile b/tools/Makefile index a7d1e18fe2..c31437e6a2 100644 --- a/tools/Makefile +++ b/tools/Makefile @@ -92,6 +92,7 @@ OBJ_FILES-$(CONFIG_CMD_LOADS) += img2srec.o OBJ_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes.o NOPED_OBJ_FILES-y += aisimage.o NOPED_OBJ_FILES-y += kwbimage.o +NOPED_OBJ_FILES-y += pblimage.o NOPED_OBJ_FILES-y += imximage.o NOPED_OBJ_FILES-y += omapimage.o NOPED_OBJ_FILES-y += mkenvimage.o @@ -208,6 +209,7 @@ $(obj)mkimage$(SFX): $(obj)aisimage.o \ $(obj)image.o \ $(obj)imximage.o \ $(obj)kwbimage.o \ + $(obj)pblimage.o \ $(obj)md5.o \ $(obj)mkimage.o \ $(obj)os_support.o \ diff --git a/tools/mkimage.c b/tools/mkimage.c index eeb1b10668..e43b09f766 100644 --- a/tools/mkimage.c +++ b/tools/mkimage.c @@ -39,6 +39,7 @@ struct mkimage_params params = { .comp = IH_COMP_GZIP, .dtc = MKIMAGE_DEFAULT_DTC_OPTIONS, .imagename = "", + .imagename2 = "", }; /* @@ -150,6 +151,8 @@ main (int argc, char **argv) int retval = 0; struct image_type_params *tparams = NULL; + /* Init Freescale PBL Boot image generation/list support */ + init_pbl_image_type(); /* Init Kirkwood Boot image generation/list support */ init_kwb_image_type (); /* Init Freescale imx Boot image generation/list support */ @@ -250,6 +253,15 @@ main (int argc, char **argv) usage (); params.imagename = *++argv; goto NXTARG; + case 'R': + if (--argc <= 0) + usage(); + /* + * This entry is for the second configuration + * file, if only one is not enough. + */ + params.imagename2 = *++argv; + goto NXTARG; case 's': params.skipcpy = 1; break; @@ -440,6 +452,9 @@ NXTARG: ; break; } } + } else if (params.type == IH_TYPE_PBLIMAGE) { + /* PBL has special Image format, implements its' own */ + pbl_load_uboot(ifd, ¶ms); } else { copy_file (ifd, params.datafile, 0); } diff --git a/tools/mkimage.h b/tools/mkimage.h index 5fe1a48ccf..ea45f5c834 100644 --- a/tools/mkimage.h +++ b/tools/mkimage.h @@ -69,6 +69,7 @@ struct mkimage_params { unsigned int addr; unsigned int ep; char *imagename; + char *imagename2; char *datafile; char *imagefile; char *cmdname; @@ -147,6 +148,8 @@ void mkimage_register (struct image_type_params *tparams); * * Supported image types init functions */ +void pbl_load_uboot(int fd, struct mkimage_params *mparams); +void init_pbl_image_type(void); void init_ais_image_type(void); void init_kwb_image_type (void); void init_imx_image_type (void); diff --git a/tools/pblimage.c b/tools/pblimage.c new file mode 100644 index 0000000000..508a747a3f --- /dev/null +++ b/tools/pblimage.c @@ -0,0 +1,331 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#define _GNU_SOURCE + +#include "mkimage.h" +#include <image.h> +#include "pblimage.h" + +/* + * The PBL can load up to 64 bytes at a time, so we split the U-Boot + * image into 64 byte chunks. PBL needs a command for each piece, of + * the form "81xxxxxx", where "xxxxxx" is the offset. SYS_TEXT_BASE + * is 0xFFF80000 for PBL boot, and PBL only cares about low 24-bit, + * so it starts from 0x81F80000. + */ +static uint32_t next_pbl_cmd = 0x81F80000; +/* + * need to store all bytes in memory for calculating crc32, then write the + * bytes to image file for PBL boot. + */ +static unsigned char mem_buf[600000]; +static unsigned char *pmem_buf = mem_buf; +static int pbl_size; +static char *fname = "Unknown"; +static int lineno = -1; +static struct pbl_header pblimage_header; + +static union +{ + char c[4]; + unsigned char l; +} endian_test = { {'l', '?', '?', 'b'} }; + +#define ENDIANNESS ((char)endian_test.l) + +static void generate_pbl_cmd(void) +{ + uint32_t val = next_pbl_cmd; + next_pbl_cmd += 0x40; + int i; + + for (i = 3; i >= 0; i--) { + *pmem_buf++ = (val >> (i * 8)) & 0xff; + pbl_size++; + } +} + +static void pbl_fget(size_t size, FILE *stream) +{ + unsigned char c; + int c_temp; + + while (size && (c_temp = fgetc(stream)) != EOF) { + c = (unsigned char)c_temp; + *pmem_buf++ = c; + pbl_size++; + size--; + } +} + +/* load split u-boot with PBI command 81xxxxxx. */ +static void load_uboot(FILE *fp_uboot) +{ + while (next_pbl_cmd < 0x82000000) { + generate_pbl_cmd(); + pbl_fget(64, fp_uboot); + } +} + +static void check_get_hexval(char *token) +{ + uint32_t hexval; + int i; + + if (!sscanf(token, "%x", &hexval)) { + printf("Error:%s[%d] - Invalid hex data(%s)\n", fname, + lineno, token); + exit(EXIT_FAILURE); + } + for (i = 3; i >= 0; i--) { + *pmem_buf++ = (hexval >> (i * 8)) & 0xff; + pbl_size++; + } +} + +static void pbl_parser(char *name) +{ + FILE *fd = NULL; + char *line = NULL; + char *token, *saveptr1, *saveptr2; + size_t len = 0; + + fname = name; + fd = fopen(name, "r"); + if (fd == NULL) { + printf("Error:%s - Can't open\n", fname); + exit(EXIT_FAILURE); + } + + while ((getline(&line, &len, fd)) > 0) { + lineno++; + token = strtok_r(line, "\r\n", &saveptr1); + /* drop all lines with zero tokens (= empty lines) */ + if (token == NULL) + continue; + for (line = token;; line = NULL) { + token = strtok_r(line, " \t", &saveptr2); + if (token == NULL) + break; + /* Drop all text starting with '#' as comments */ + if (token[0] == '#') + break; + check_get_hexval(token); + } + } + if (line) + free(line); + fclose(fd); +} + +static uint32_t crc_table[256]; + +static void make_crc_table(void) +{ + uint32_t mask; + int i, j; + uint32_t poly; /* polynomial exclusive-or pattern */ + + /* + * the polynomial used by PBL is 1 + x1 + x2 + x4 + x5 + x7 + x8 + x10 + * + x11 + x12 + x16 + x22 + x23 + x26 + x32. + */ + poly = 0x04c11db7; + + for (i = 0; i < 256; i++) { + mask = i << 24; + for (j = 0; j < 8; j++) { + if (mask & 0x80000000) + mask = (mask << 1) ^ poly; + else + mask <<= 1; + } + crc_table[i] = mask; + } +} + +unsigned long pbl_crc32(unsigned long crc, const char *buf, uint32_t len) +{ + uint32_t crc32_val = 0xffffffff; + uint32_t xor = 0x0; + int i; + + make_crc_table(); + + for (i = 0; i < len; i++) + crc32_val = (crc32_val << 8) ^ + crc_table[(crc32_val >> 24) ^ (*buf++ & 0xff)]; + + crc32_val = crc32_val ^ xor; + if (crc32_val < 0) { + crc32_val += 0xffffffff; + crc32_val += 1; + } + return crc32_val; +} + +static uint32_t reverse_byte(uint32_t val) +{ + uint32_t temp; + unsigned char *p1; + int j; + + temp = val; + p1 = (unsigned char *)&temp; + for (j = 3; j >= 0; j--) + *p1++ = (val >> (j * 8)) & 0xff; + return temp; +} + +/* write end command and crc command to memory. */ +static void add_end_cmd(void) +{ + uint32_t pbl_end_cmd[4] = {0x09138000, 0x00000000, + 0x091380c0, 0x00000000}; + uint32_t crc32_pbl; + int i; + unsigned char *p = (unsigned char *)&pbl_end_cmd; + + if (ENDIANNESS == 'l') { + for (i = 0; i < 4; i++) + pbl_end_cmd[i] = reverse_byte(pbl_end_cmd[i]); + } + + for (i = 0; i < 16; i++) { + *pmem_buf++ = *p++; + pbl_size++; + } + + /* Add PBI CRC command. */ + *pmem_buf++ = 0x08; + *pmem_buf++ = 0x13; + *pmem_buf++ = 0x80; + *pmem_buf++ = 0x40; + pbl_size += 4; + + /* calculated CRC32 and write it to memory. */ + crc32_pbl = pbl_crc32(0, (const char *)mem_buf, pbl_size); + *pmem_buf++ = (crc32_pbl >> 24) & 0xff; + *pmem_buf++ = (crc32_pbl >> 16) & 0xff; + *pmem_buf++ = (crc32_pbl >> 8) & 0xff; + *pmem_buf++ = (crc32_pbl) & 0xff; + pbl_size += 4; + + if ((pbl_size % 16) != 0) { + for (i = 0; i < 8; i++) { + *pmem_buf++ = 0x0; + pbl_size++; + } + } + if ((pbl_size % 16 != 0)) { + printf("Error: Bad size of image file\n"); + exit(EXIT_FAILURE); + } +} + +void pbl_load_uboot(int ifd, struct mkimage_params *params) +{ + FILE *fp_uboot; + int size; + + /* parse the rcw.cfg file. */ + pbl_parser(params->imagename); + + /* parse the pbi.cfg file. */ + pbl_parser(params->imagename2); + + fp_uboot = fopen(params->datafile, "r"); + if (fp_uboot == NULL) { + printf("Error: %s open failed\n", params->datafile); + exit(EXIT_FAILURE); + } + + load_uboot(fp_uboot); + add_end_cmd(); + fclose(fp_uboot); + lseek(ifd, 0, SEEK_SET); + + size = pbl_size; + if (write(ifd, (const void *)&mem_buf, size) != size) { + fprintf(stderr, "Write error on %s: %s\n", + params->imagefile, strerror(errno)); + exit(EXIT_FAILURE); + } +} + +static int pblimage_check_image_types(uint8_t type) +{ + if (type == IH_TYPE_PBLIMAGE) + return EXIT_SUCCESS; + else + return EXIT_FAILURE; +} + +static int pblimage_verify_header(unsigned char *ptr, int image_size, + struct mkimage_params *params) +{ + struct pbl_header *pbl_hdr = (struct pbl_header *) ptr; + + /* Only a few checks can be done: search for magic numbers */ + if (ENDIANNESS == 'l') { + if (pbl_hdr->preamble != reverse_byte(RCW_PREAMBLE)) + return -FDT_ERR_BADSTRUCTURE; + + if (pbl_hdr->rcwheader != reverse_byte(RCW_HEADER)) + return -FDT_ERR_BADSTRUCTURE; + } else { + if (pbl_hdr->preamble != RCW_PREAMBLE) + return -FDT_ERR_BADSTRUCTURE; + + if (pbl_hdr->rcwheader != RCW_HEADER) + return -FDT_ERR_BADSTRUCTURE; + } + return 0; +} + +static void pblimage_print_header(const void *ptr) +{ + printf("Image Type: Freescale PBL Boot Image\n"); +} + +static void pblimage_set_header(void *ptr, struct stat *sbuf, int ifd, + struct mkimage_params *params) +{ + /*nothing need to do, pbl_load_uboot takes care of whole file. */ +} + +/* pblimage parameters */ +static struct image_type_params pblimage_params = { + .name = "Freescale PBL Boot Image support", + .header_size = sizeof(struct pbl_header), + .hdr = (void *)&pblimage_header, + .check_image_type = pblimage_check_image_types, + .verify_header = pblimage_verify_header, + .print_header = pblimage_print_header, + .set_header = pblimage_set_header, +}; + +void init_pbl_image_type(void) +{ + pbl_size = 0; + mkimage_register(&pblimage_params); +} diff --git a/board/freescale/p3060qds/p3060qds.h b/tools/pblimage.h index 3da6815f0f..514a477ca4 100644 --- a/board/freescale/p3060qds/p3060qds.h +++ b/tools/pblimage.h @@ -1,5 +1,8 @@ /* - * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -8,7 +11,7 @@ * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License @@ -17,14 +20,17 @@ * MA 02111-1307 USA */ -#ifndef __P3060QDS_H__ -#define __P3060QDS_H__ +#ifndef PBLIMAGE_H +#define PBLIMAGE_H -#include <asm/fsl_ddr_sdram.h> -#include <asm/u-boot.h> +#define RCW_BYTES 64 +#define RCW_PREAMBLE 0xaa55aa55 +#define RCW_HEADER 0x010e0100 -void fdt_fixup_board_enet(void *blob); -void pci_of_setup(void *blob, bd_t *bd); -extern fixed_ddr_parm_t fixed_ddr_parm_0[]; +struct pbl_header { + uint32_t preamble; + uint32_t rcwheader; + uint8_t rcw_data[RCW_BYTES]; +}; -#endif +#endif /* PBLIMAGE_H */ |
