PXA: Remove "wepep250" board

This board is broken and impossible to repair without deep knowledge or
availability of the hardware.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

1 files changed, 0 insertions, 199 deletions

diff --git a/include/configs/wepep250.h b/include/configs/wepep250.h
deleted file mode 100644
index a961a27922..0000000000
--- a/include/configs/wepep250.h
+++ /dev/null
@@ -1,199 +0,0 @@
-/*
- * Copyright (C) 2003 ETC s.r.o.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- * Written by Peter Figuli <peposh@etc.sk>, 2003.
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_PXA250          1        /* this is an PXA250 CPU     */
-#define CONFIG_WEPEP250        1        /* config for wepep250 board */
-#undef  CONFIG_USE_IRQ                  /* don't need use IRQ/FIQ    */
-
-/* we will never enable dcache, because we have to setup MMU first */
-#define CONFIG_SYS_NO_DCACHE
-
-/*
- * Select serial console configuration
- */
-#define CONFIG_PXA_SERIAL
-#define CONFIG_BTUART          1       /* BTUART is default on WEP dev board */
-#define CONFIG_BAUDRATE   115200
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#undef CONFIG_CMD_CONSOLE
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_SOURCE
-
-
-/*
- * Boot options. Setting delay to -1 stops autostart count down.
- * NOTE: Sending parameters to kernel depends on kernel version and
- * 2.4.19-rmk6-pxa1 patch used while my u-boot coding didn't accept
- * parameters at all! Do not get confused by them so.
- */
-#define CONFIG_BOOTDELAY   -1
-#define CONFIG_BOOTARGS    "root=/dev/mtdblock2 mem=32m console=ttyS01,115200n8"
-#define CONFIG_BOOTCOMMAND "bootm 40000"
-
-
-/*
- * General options for u-boot. Modify to save memory foot print
- */
-#define CONFIG_SYS_LONGHELP                                  /* undef saves memory  */
-#define CONFIG_SYS_PROMPT              "WEP> "               /* prompt string       */
-#define CONFIG_SYS_CBSIZE              256                   /* console I/O buffer  */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* print buffer size   */
-#define CONFIG_SYS_MAXARGS             16                    /* max command args    */
-#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE            /* boot args buf size  */
-
-#define CONFIG_SYS_MEMTEST_START       0xa0400000            /* memtest test area   */
-#define CONFIG_SYS_MEMTEST_END         0xa0800000
-
-#define CONFIG_SYS_HZ			1000
-#define CONFIG_SYS_CPUSPEED            0x141        /* core clock - register value  */
-
-#define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Definitions related to passing arguments to kernel.
- */
-#define CONFIG_CMDLINE_TAG           1   /* send commandline to Kernel       */
-#define CONFIG_SETUP_MEMORY_TAGS     1   /* send memory definition to kernel */
-#undef  CONFIG_INITRD_TAG                /* do not send initrd params        */
-#undef  CONFIG_VFD                       /* do not send framebuffer setup    */
-
-
-/*
- * Malloc pool need to host env + 128 Kb reserve for other allocations.
- */
-#define CONFIG_SYS_MALLOC_LEN	  (CONFIG_ENV_SIZE + (128<<10) )
-#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
-
-#define CONFIG_STACKSIZE        (120<<10)      /* stack size */
-
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ    (4<<10)        /* IRQ stack  */
-#define CONFIG_STACKSIZE_FIQ    (4<<10)        /* FIQ stack  */
-#endif
-
-/*
- * SDRAM Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS    1                /* we have 1 bank of SDRAM */
-#define WEP_SDRAM_1            0xa0000000        /* SDRAM bank #1           */
-#define WEP_SDRAM_1_SIZE       0x02000000        /* 32 MB ( 2 chip )        */
-#define WEP_SDRAM_2            0xa2000000        /* SDRAM bank #2           */
-#define WEP_SDRAM_2_SIZE       0x00000000        /* 0 MB                    */
-#define WEP_SDRAM_3            0xa8000000        /* SDRAM bank #3           */
-#define WEP_SDRAM_3_SIZE       0x00000000        /* 0 MB                    */
-#define WEP_SDRAM_4            0xac000000        /* SDRAM bank #4           */
-#define WEP_SDRAM_4_SIZE       0x00000000        /* 0 MB                    */
-
-#define CONFIG_SYS_DRAM_BASE           0xa0000000
-#define CONFIG_SYS_DRAM_SIZE           0x02000000
-
-/* Uncomment used SDRAM chip */
-#define WEP_SDRAM_K4S281633
-/*#define WEP_SDRAM_K4S561633*/
-
-
-/*
- * Configuration for FLASH memory
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* FLASH banks count (not chip count)*/
-#define CONFIG_SYS_MAX_FLASH_SECT	128	/* number of sector in FLASH bank    */
-#define WEP_FLASH_BUS_WIDTH	4	/* we use 32 bit FLASH memory...     */
-#define WEP_FLASH_INTERLEAVE	2	/* ... made of 2 chips */
-#define WEP_FLASH_BANK_SIZE  0x2000000  /* size of one flash bank*/
-#define WEP_FLASH_SECT_SIZE  0x0040000  /* size of erase sector */
-#define WEP_FLASH_BASE       0x0000000  /* location of flash memory */
-#define WEP_FLASH_UNLOCK        1       /* perform hw unlock first */
-
-
-/* This should be defined if CFI FLASH device is present. Actually benefit
-   is not so clear to me. In other words we can provide more informations
-   to user, but this expects more complex flash handling we do not provide
-   now.*/
-#undef  CONFIG_SYS_FLASH_CFI
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT    (2*CONFIG_SYS_HZ)    /* timeout for Erase operation */
-#define CONFIG_SYS_FLASH_WRITE_TOUT    (2*CONFIG_SYS_HZ)    /* timeout for Write operation */
-
-#define CONFIG_SYS_FLASH_BASE          WEP_FLASH_BASE
-
-/*
- * This is setting for JFFS2 support in u-boot.
- * Right now there is no gain for user, but later on booting kernel might be
- * possible. Consider using XIP kernel running from flash to save RAM
- * footprint.
- * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
- */
-#define CONFIG_SYS_JFFS2_FIRST_BANK		0
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR		5
-#define CONFIG_SYS_JFFS2_NUM_BANKS		1
-
-/*
- * Environment setup. Definitions of monitor location and size with
- * definition of environment setup ends up in 2 possibilities.
- * 1. Embeded environment - in u-boot code is space for environment
- * 2. Environment is read from predefined sector of flash
- * Right now we support 2. possiblity, but expecting no env placed
- * on mentioned address right now. This also needs to provide whole
- * sector for it - for us 256Kb is really waste of memory. U-boot uses
- * default env. and until kernel parameters could be sent to kernel
- * env. has no sense to us.
- */
-
-#define CONFIG_SYS_MONITOR_BASE	PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_LEN		0x20000		/* 128kb ( 1 flash sector )  */
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		0x20000	        /* absolute address for now  */
-#define CONFIG_ENV_SIZE		0x2000
-
-#define	PHYS_SDRAM_1			WEP_SDRAM_1
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
-#define	CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_GBL_DATA_SIZE + PHYS_SDRAM_1)
-
-#undef  CONFIG_ENV_OVERWRITE                    /* env is not writable now   */
-
-/*
- * Well this has to be defined, but on the other hand it is used differently
- * one may expect. For instance loadb command do not cares :-)
- * So advice is - do not relay on this...
- */
-#define CONFIG_SYS_LOAD_ADDR        0x40000
-
-#endif  /* __CONFIG_H */