powerpc: hiddendragon: remove orphan board

This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)

Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>

1 files changed, 0 insertions, 371 deletions

diff --git a/include/configs/HIDDEN_DRAGON.h b/include/configs/HIDDEN_DRAGON.h
deleted file mode 100644
index e0a233b28a..0000000000
--- a/include/configs/HIDDEN_DRAGON.h
+++ /dev/null
@@ -1,371 +0,0 @@
-/*
- * (C) Copyright 2004
- * Yusdi Santoso, Adaptec Inc., yusdi_santoso@adaptec.com
- *
- * (C) Copyright 2001, 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8245		1
-#define CONFIG_HIDDEN_DRAGON	1
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF00000
-
-#if 0
-#define USE_DINK32		1
-#else
-#undef USE_DINK32
-#endif
-
-#define CONFIG_CONS_INDEX	3		/* set to '3' for on-chip DUART */
-#define CONFIG_BAUDRATE		9600
-#define CONFIG_DRAM_SPEED	100		/* MHz				*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP		1		/* undef to save memory		*/
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size	*/
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-#define CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address		*/
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_PCI				/* include pci support		*/
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#undef CONFIG_PCI_PNP
-
-
-#define CONFIG_SYS_RX_ETH_BUFFER	8		/* use 8 rx buffer on eepro100	*/
-
-#define PCI_ENET0_IOADDR	0x80000000
-#define PCI_ENET0_MEMADDR	0x80000000
-#define PCI_ENET1_IOADDR	0x81000000
-#define PCI_ENET1_MEMADDR	0x81000000
-
-#define CONFIG_RTL8139
-
-/* Make sure the ethaddr can be overwritten
-   TODO: Remove this on final product
-*/
-#define CONFIG_ENV_OVERWRITE
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE	0x02000000
-
-#define CONFIG_SYS_RESET_ADDRESS	0xFFF00100
-
-#if defined (USE_DINK32)
-#define CONFIG_SYS_MONITOR_LEN		0x00030000
-#define CONFIG_SYS_MONITOR_BASE	0x00090000
-#define CONFIG_SYS_RAMBOOT		1
-#define CONFIG_SYS_INIT_RAM_ADDR	(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_SYS_INIT_RAM_SIZE	0x10000
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-#else
-#undef	CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_MONITOR_LEN		0x00030000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-
-
-#define CONFIG_SYS_INIT_RAM_ADDR     0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE      0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET  (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-#endif
-
-#define CONFIG_SYS_FLASH_BASE		0xFFE00000
-#define CONFIG_SYS_FLASH_SIZE		(2 * 1024 * 1024)	/* Unity has onboard 1MByte flash */
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_OFFSET		0x00004000	/* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE		0x00002000	/* Total Size of Environment Sector */
-
-#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 512 kB for malloc()	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on		*/
-#define CONFIG_SYS_MEMTEST_END		0x02000000	/* 0 ... 32 MB in DRAM		*/
-
-#define CONFIG_SYS_EUMB_ADDR		0xFC000000
-
-#define CONFIG_SYS_ISA_MEM		0xFD000000
-#define CONFIG_SYS_ISA_IO		0xFE000000
-
-#define CONFIG_SYS_FLASH_RANGE_BASE	0xFFE00000	/* flash memory address range	*/
-#define CONFIG_SYS_FLASH_RANGE_SIZE	0x00200000
-#define FLASH_BASE0_PRELIM	0xFFE00000	/* processor board flash	*/
-
-/*
- * select i2c support configuration
- *
- * Supported configurations are {none, software, hardware} drivers.
- * If the software driver is chosen, there are some additional
- * configuration items that the driver uses to drive the port pins.
- */
-#define CONFIG_HARD_I2C		1		/* To enable I2C support	*/
-#undef	CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-#ifdef CONFIG_SYS_I2C_SOFT
-#error "Soft I2C is not configured properly.  Please review!"
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT_SPEED	50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-#define I2C_PORT		3		/* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE		(iop->pdir |=  0x00010000)
-#define I2C_TRISTATE		(iop->pdir &= ~0x00010000)
-#define I2C_READ		((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit)		if(bit) iop->pdat |=  0x00010000; \
-				else	iop->pdat &= ~0x00010000
-#define I2C_SCL(bit)		if(bit) iop->pdat |=  0x00020000; \
-				else	iop->pdat &= ~0x00020000
-#define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
-#endif /* CONFIG_SYS_I2C_SOFT */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57		/* EEPROM IS24C02		*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1		/* Bytes of address		*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
-
-#define CONFIG_SYS_FLASH_BANKS		{ FLASH_BASE0_PRELIM }
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-
-
-/* #define CONFIG_WINBOND_83C553	1	/ *has a winbond bridge			*/
-#define CONFIG_SYS_USE_WINBOND_IDE	0	/*use winbond 83c553 internal IDE ctrlr */
-#define CONFIG_SYS_WINBOND_ISA_CFG_ADDR    0x80005800	/*pci-isa bridge config addr	*/
-#define CONFIG_SYS_WINBOND_IDE_CFG_ADDR    0x80005900	/*ide config addr		*/
-
-#define CONFIG_SYS_IDE_MAXBUS		2   /* max. 2 IDE busses	*/
-#define CONFIG_SYS_IDE_MAXDEVICE	(CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-
-/* TODO: Change this to VIA686A */
-
-/*
- * NS87308 Configuration
- */
-#define CONFIG_NS87308			/* Nat Semi super-io controller on ISA bus */
-
-#define CONFIG_SYS_NS87308_BADDR_10	1
-
-#define CONFIG_SYS_NS87308_DEVS	( CONFIG_SYS_NS87308_UART1   | \
-				  CONFIG_SYS_NS87308_UART2   | \
-				  CONFIG_SYS_NS87308_POWRMAN | \
-				  CONFIG_SYS_NS87308_RTC_APC )
-
-#undef	CONFIG_SYS_NS87308_PS2MOD
-
-#define CONFIG_SYS_NS87308_CS0_BASE	0x0076
-#define CONFIG_SYS_NS87308_CS0_CONF	0x30
-#define CONFIG_SYS_NS87308_CS1_BASE	0x0075
-#define CONFIG_SYS_NS87308_CS1_CONF	0x30
-#define CONFIG_SYS_NS87308_CS2_BASE	0x0074
-#define CONFIG_SYS_NS87308_CS2_CONF	0x30
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-
-#if (CONFIG_CONS_INDEX > 2)
-#define CONFIG_SYS_NS16550_CLK		CONFIG_DRAM_SPEED*1000000
-#else
-#define CONFIG_SYS_NS16550_CLK		1843200
-#endif
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART1_BASE)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART2_BASE)
-#define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_EUMB_ADDR + 0x4500)
-#define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_EUMB_ADDR + 0x4600)
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_CLK_FREQ  33333333	/* external frequency to pll */
-
-#define CONFIG_SYS_ROMNAL		7	/*rom/flash next access time		*/
-#define CONFIG_SYS_ROMFAL		11	/*rom/flash access time			*/
-
-#define CONFIG_SYS_REFINT	430	/* no of clock cycles between CBR refresh cycles */
-
-/* the following are for SDRAM only*/
-#define CONFIG_SYS_BSTOPRE	121	/* Burst To Precharge, sets open page interval */
-#define CONFIG_SYS_REFREC		8	/* Refresh to activate interval		*/
-#define CONFIG_SYS_RDLAT		4	/* data latency from read command	*/
-#define CONFIG_SYS_PRETOACT		3	/* Precharge to activate interval	*/
-#define CONFIG_SYS_ACTTOPRE		5	/* Activate to Precharge interval	*/
-#define CONFIG_SYS_ACTORW		3	/* Activate to R/W			*/
-#define CONFIG_SYS_SDMODE_CAS_LAT	3	/* SDMODE CAS latency			*/
-#define CONFIG_SYS_SDMODE_WRAP		0	/* SDMODE wrap type			*/
-#if 0
-#define CONFIG_SYS_SDMODE_BURSTLEN	2	/* OBSOLETE!  SDMODE Burst length 2=4, 3=8		*/
-#endif
-
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER   1
-#define CONFIG_SYS_EXTROM 1
-#define CONFIG_SYS_REGDIMM 0
-
-
-/* memory bank settings*/
-/*
- * only bits 20-29 are actually used from these vales to set the
- * start/end address the upper two bits will be 0, and the lower 20
- * bits will be set to 0x00000 for a start address, or 0xfffff for an
- * end address
- */
-#define CONFIG_SYS_BANK0_START		0x00000000
-#define CONFIG_SYS_BANK0_END		(CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE	1
-#define CONFIG_SYS_BANK1_START		0x3ff00000
-#define CONFIG_SYS_BANK1_END		0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE	0
-#define CONFIG_SYS_BANK2_START		0x3ff00000
-#define CONFIG_SYS_BANK2_END		0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE	0
-#define CONFIG_SYS_BANK3_START		0x3ff00000
-#define CONFIG_SYS_BANK3_END		0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE	0
-#define CONFIG_SYS_BANK4_START		0x00000000
-#define CONFIG_SYS_BANK4_END		0x00000000
-#define CONFIG_SYS_BANK4_ENABLE	0
-#define CONFIG_SYS_BANK5_START		0x00000000
-#define CONFIG_SYS_BANK5_END		0x00000000
-#define CONFIG_SYS_BANK5_ENABLE	0
-#define CONFIG_SYS_BANK6_START		0x00000000
-#define CONFIG_SYS_BANK6_END		0x00000000
-#define CONFIG_SYS_BANK6_ENABLE	0
-#define CONFIG_SYS_BANK7_START		0x00000000
-#define CONFIG_SYS_BANK7_END		0x00000000
-#define CONFIG_SYS_BANK7_ENABLE	0
-/*
- * Memory bank enable bitmask, specifying which of the banks defined above
- are actually present. MSB is for bank #7, LSB is for bank #0.
- */
-#define CONFIG_SYS_BANK_ENABLE		0x01
-
-#define CONFIG_SYS_ODCR		0xff	/* configures line driver impedances,	*/
-					/* see 8240 book for bit definitions	*/
-#define CONFIG_SYS_PGMAX		0x32	/* how long the 8240 retains the	*/
-					/* currently accessed page in memory	*/
-					/* see 8240 book for details		*/
-
-/* SDRAM 0 - 256MB */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* stack in DCACHE @ 1GB (no backing mem) */
-#if defined(USE_DINK32)
-#define CONFIG_SYS_IBAT1L	(0x40000000 | BATL_PP_00 )
-#define CONFIG_SYS_IBAT1U	(0x40000000 | BATU_BL_128K )
-#else
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#endif
-
-/* PCI memory */
-#define CONFIG_SYS_IBAT2L	(0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U	(0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* Flash, config addrs, etc */
-#define CONFIG_SYS_IBAT3L	(0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	36	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8240 CPU			*/
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-/* values according to the manual */
-#define CONFIG_DRAM_50MHZ	1
-#define CONFIG_SDRAM_50MHZ
-
-#undef	NR_8259_INTS
-#define NR_8259_INTS		1
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-#endif	/* __CONFIG_H */