ppc4xx: remove G2000 board

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>

1 files changed, 0 insertions, 383 deletions

diff --git a/include/configs/G2000.h b/include/configs/G2000.h
deleted file mode 100644
index 0c66092e0b..0000000000
--- a/include/configs/G2000.h
+++ /dev/null
@@ -1,383 +0,0 @@
-/*
- * (C) Copyright 2004
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_G2000		1	/* ...on a PLU405 board		*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
-#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
-
-#define CONFIG_SYS_CLK_FREQ     33333333 /* external frequency to pll   */
-
-#if 0 /* test-only */
-#define CONFIG_BAUDRATE		115200
-#else
-#define CONFIG_BAUDRATE		9600
-#endif
-
-#define CONFIG_PREBOOT
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off\0"				\
-	"addmisc=setenv bootargs ${bootargs} "				\
-		"console=ttyS0,${baudrate} "				\
-		"panic=1\0"						\
-	"flash_nfs=run nfsargs addip addmisc;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addmisc;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};"				\
-		"run nfsargs addip addmisc;bootm\0"			\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/g2000/pImage\0"				\
-	"kernel_addr=ff800000\0"				        \
-	"ramdisk_addr=ff900000\0"				        \
-	"pciconfighost=yes\0"				                \
-	""
-#define CONFIG_BOOTCOMMAND	"run net_nfs"
-
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_PHY_ADDR		0	/* PHY address			*/
-#define CONFIG_PHY1_ADDR	1	/* PHY address			*/
-
-#if 0 /* test-only */
-#define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
-#endif
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_EEPROM
-
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#if 0 /* test-only */
-#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#undef	CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser	*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device	*/
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
-
-#define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_CONS_INDEX	1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
-
-#undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* no external serial clock used */
-#define CONFIG_SYS_BASE_BAUD	    691200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
-	 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
-#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
-
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
-#define CONFIG_SYS_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
-
-/*----------------------------------------------------------------------------*/
-/* adding Ethernet setting:  FTS OUI 00:11:0B */
-/*----------------------------------------------------------------------------*/
-#define CONFIG_ETHADDR          00:11:0B:00:00:01
-#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR         00:11:0B:00:00:02
-#define CONFIG_IPADDR		10.48.8.178
-#define CONFIG_IP1ADDR		10.48.8.188
-#define CONFIG_NETMASK		255.255.255.128
-#define CONFIG_SERVERIP		10.48.8.138
-
-/*-----------------------------------------------------------------------
- * RTC stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_I2C_RTC_ADDR	0x68
-
-#if 0 /* test-only */
-/*-----------------------------------------------------------------------
- * NAND-FLASH stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-
-#define CONFIG_SYS_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CONFIG_SYS_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CONFIG_SYS_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CONFIG_SYS_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#endif
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
-
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_HOST	PCI_HOST_HOST   /* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
-
-#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
-
-#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
-#define CONFIG_SYS_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CONFIG_SYS_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CONFIG_SYS_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CONFIG_SYS_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CONFIG_SYS_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#if 0 /* APC405 */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max number of sectors on one chip	*/
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#undef CONFIG_SYS_FLASH_PROTECTION		/* don't use hardware protection	*/
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
-#define CONFIG_SYS_FLASH_BASE		0xFE000000 /* test-only...*/
-#define CONFIG_SYS_FLASH_INCREMENT	0x01000000 /* test-only */
-#else /* G2000 */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max number of sectors on one chip	*/
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#undef CONFIG_SYS_FLASH_PROTECTION		/* don't use hardware protection	*/
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
-#define CONFIG_SYS_FLASH_BASE		0xFF800000 /* test-only...*/
-#define CONFIG_SYS_FLASH_INCREMENT	0x01000000 /* test-only */
-#endif
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
-
-#define CONFIG_SYS_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
-#define CONFIG_SYS_JFFS2_NUM_BANKS     1           /* ! second bank contains u-boot    */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_MONITOR_BASE	0xFFFC0000
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
-
-/*-----------------------------------------------------------------------
- * Environment Variable setup
- */
-#if 1 /* test-only */
-#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET		0x100	/* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
-				   /* total size of a CAT24WC16 is 2048 bytes */
-
-#else	/* DEFAULT: environment in flash, using redundand flash sectors */
-
-#define CONFIG_ENV_IS_IN_FLASH	1	/* use FLASH for environment vars */
-#define CONFIG_ENV_ADDR		0xFFFA0000 /* environment starts before u-boot */
-#define CONFIG_ENV_SECT_SIZE	0x20000	/* 128k bytes may be used for env vars*/
-
-#endif
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC16) for environment
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
-/* CAT24WC08/16... */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
-					/* 16 byte page write mode using*/
-					/* last 4 bits of the address	*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-/* Memory Bank 0 (Intel Strata Flash) initialization                            */
-#define CONFIG_SYS_EBC_PB0AP   0x92015480
-#define CONFIG_SYS_EBC_PB0CR   0xFF87A000          /* BAS=0xFF8,BS=08MB,BU=R/W,BW=16bit*/
-
-/* Memory Bank 1 ( Power TAU) initialization               */
-/* #define CONFIG_SYS_EBC_PB1AP           0x04041000 */
-/* #define CONFIG_SYS_EBC_PB1CR           0xF0018000   */  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
-#define CONFIG_SYS_EBC_PB1AP           0x00000000
-#define CONFIG_SYS_EBC_PB1CR           0x00000000
-
-/* Memory Bank 2 (Intel Flash) initialization                 */
-#define CONFIG_SYS_EBC_PB2AP           0x00000000
-#define CONFIG_SYS_EBC_PB2CR           0x00000000
-
-/* Memory Bank 3 (NAND) initialization                        */
-#define CONFIG_SYS_EBC_PB3AP           0x92015480
-#define CONFIG_SYS_EBC_PB3CR           0xF40B8000  /*addr 0xF40, BS=32M,BU=R/W, BW=8bit */
-
-/* Memory Bank 4 (FPGA regs) initialization                                     */
-#define CONFIG_SYS_EBC_PB4AP           0x00000000
-#define CONFIG_SYS_EBC_PB4CR           0x00000000  /* leave it blank  */
-
-#define CONFIG_SYS_NAND_BASE   0xF4000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CONFIG_SYS_TEMP_STACK_OCM	  1
-
-/* On Chip Memory location */
-#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
-#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EP specific)
- *
- * GPIO0[0]     - External Bus Controller BLAST output
- * GPIO0[1-9]   - Instruction trace outputs
- * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
- * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs
- * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
- * GPIO0[24-27] - UART0 control signal inputs/outputs
- * GPIO0[28-29] - UART1 data signal input/output
- * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
- *
- * following GPIO setting changed for G20000, 080304
- */
-#define CONFIG_SYS_GPIO0_OSRL          0x40005555
-#define CONFIG_SYS_GPIO0_OSRH          0x40000110
-#define CONFIG_SYS_GPIO0_ISR1L         0x00000000
-#define CONFIG_SYS_GPIO0_ISR1H         0x15555445
-#define CONFIG_SYS_GPIO0_TSRL          0x00000000
-#define CONFIG_SYS_GPIO0_TSRH          0x00000000
-#define CONFIG_SYS_GPIO0_TCR           0xF7FF8014
-
-/*
- * Default speed selection (cpu_plb_opb_ebc) in mhz.
- * This value will be set if iic boot eprom is disabled.
- */
-#if 1
-#define PLLMR0_DEFAULT	 PLLMR0_266_66_33_33
-#define PLLMR1_DEFAULT	 PLLMR1_266_66_33_33
-#endif
-#if 0
-#define PLLMR0_DEFAULT	 PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT	 PLLMR1_266_133_66_33
-#endif
-#if 0
-#define PLLMR0_DEFAULT	 PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT	 PLLMR1_200_100_50_33
-#endif
-#if 0
-#define PLLMR0_DEFAULT	 PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT	 PLLMR1_133_66_66_33
-#endif
-
-#endif	/* __CONFIG_H */