armv8/ls2085a: Update common header file

ls2085a_common.h contains hard-coded information for NOR/NAND flash,
I2C, DDR, etc. These are platform specific. Move them out of common
header file and placed into respective board header files.

Move TEXTBASE to 1MB offset to fit NOR flash with up to 1MB sector
size.

Enable command auto complete. Update prompt symbol. Set fdt_high to
0xa0000000 because Linux requires that the fdt  be 8-byte aligned
and below 512 MiB. Besides ensuring compliance with the 512 MiB
limit, this avoids problems with the dtb being misaligned within
the FIT image.

Change the MC FW, MC DPL and Debug server NOR addresses in compliance
with the NOR flash layouts for 128MB flash.

Add PCIe macros. Enable "loadb" command. Disable debug server.
Enable workaround for erratum A008511.
Stop reset on panic for postmortem debugging.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>

1 files changed, 32 insertions, 109 deletions

diff --git a/include/configs/ls2085a_common.h b/include/configs/ls2085a_common.h
index 26ef32a177..5721b18b6f 100644
--- a/include/configs/ls2085a_common.h
+++ b/include/configs/ls2085a_common.h
@@ -23,7 +23,7 @@
 #define CONFIG_ARCH_MISC_INIT
 
 /* Link Definitions */
-#define CONFIG_SYS_TEXT_BASE		0x30001000
+#define CONFIG_SYS_TEXT_BASE		0x30100000
 
 #ifdef CONFIG_EMU
 #define CONFIG_SYS_NO_FLASH
@@ -47,8 +47,6 @@
 #define CONFIG_SYS_FSL_DDR3		/* Use DDR3 memory */
 #define CONFIG_SYS_DDR_RAW_TIMING
 #endif
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	4
 
 #define CONFIG_SYS_FSL_DDR_INTLV_256B	/* force 256 byte interleaving */
 
@@ -72,7 +70,6 @@
 #define CONFIG_SYS_DP_DDR_BASE_PHY	0
 #define CONFIG_DP_DDR_CTRL		2
 #define CONFIG_DP_DDR_NUM_CTRLS		1
-#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR	1
 
 /* Generic Timer Definitions */
 #define COUNTER_FREQUENCY		12000000	/* 12MHz */
@@ -86,8 +83,6 @@
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
 #define CONFIG_SYS_I2C_MXC_I2C4		/* enable I2C bus 4 */
-#define CONFIG_SYS_MXC_I2C1_SPEED	40000000
-#define CONFIG_SYS_MXC_I2C2_SPEED	40000000
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX       2
@@ -101,8 +96,7 @@
 
 /* IFC */
 #define CONFIG_FSL_IFC
-#define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
-#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
+
 /*
  * During booting, CS0 needs to be at the region of 0x30000000, i.e. the IFC
  * address 0. But this region is limited to 256MB. To accommodate bigger NOR
@@ -116,124 +110,55 @@
 #define CONFIG_SYS_FLASH_BASE_PHYS		0x80000000
 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
 
-/*
- * NOR Flash Timing Params
- */
-#define CONFIG_SYS_NOR0_CSPR					\
-	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)		| \
-	CSPR_PORT_SIZE_16					| \
-	CSPR_MSEL_NOR						| \
-	CSPR_V)
-#define CONFIG_SYS_NOR0_CSPR_EARLY				\
-	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)	| \
-	CSPR_PORT_SIZE_16					| \
-	CSPR_MSEL_NOR						| \
-	CSPR_V)
-#define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(12)
-#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x1) | \
-				FTIM0_NOR_TEADC(0x1) | \
-				FTIM0_NOR_TEAHC(0x1))
-#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x1) | \
-				FTIM1_NOR_TRAD_NOR(0x1))
-#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x0) | \
-				FTIM2_NOR_TCH(0x0) | \
-				FTIM2_NOR_TWP(0x1))
-#define CONFIG_SYS_NOR_FTIM3	0x04000000
-#define CONFIG_SYS_IFC_CCR	0x01000000
-
 #ifndef CONFIG_SYS_NO_FLASH
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 #define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
 #endif
 
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_MAX_ECCPOS	256
-#define CONFIG_SYS_NAND_MAX_OOBFREE	2
 #define CONFIG_SYS_NAND_BASE		0x520000000
 #define CONFIG_SYS_NAND_BASE_PHYS	0x20000000
 
-#define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
-#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
-				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
-				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
-				| CSPR_V)
-#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)
-
-#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
-				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
-				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
-				| CSOR_NAND_RAL_3	/* RAL = 2Byes */ \
-				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
-				| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
-				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
-
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
-					FTIM0_NAND_TWP(0x18)   | \
-					FTIM0_NAND_TWCHT(0x07) | \
-					FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
-					FTIM1_NAND_TWBE(0x39)  | \
-					FTIM1_NAND_TRR(0x0e)   | \
-					FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
-					FTIM2_NAND_TREH(0x0a) | \
-					FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3		0x0
-
-#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_CMD_NAND
-
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
-
-#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
-#define CONFIG_SYS_CSPR0_FINAL		CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
-
 /* Debug Server firmware */
-#define CONFIG_FSL_DEBUG_SERVER
 #define CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE	(512UL * 1024 * 1024)
-#define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
-#define CONFIG_SYS_DEBUG_SERVER_FW_ADDR			0x580C00000ULL
 /* 2 sec timeout */
 #define CONFIG_SYS_DEBUG_SERVER_TIMEOUT			(2 * 1000 * 1000)
 
 /* MC firmware */
 #define CONFIG_FSL_MC_ENET
 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE	(512UL * 1024 * 1024)
-#define CONFIG_SYS_LS_MC_FW_IN_NOR
-#define CONFIG_SYS_LS_MC_FW_ADDR	0x580200000ULL
-#define CONFIG_SYS_LS_MC_DPL_IN_NOR
-#define CONFIG_SYS_LS_MC_DPL_ADDR	0x5806C0000ULL
 /* TODO Actual DPL max length needs to be confirmed with the MC FW team */
-#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH	(256 * 1024)
-#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET    0xe00000
+#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH		(256 * 1024)
+#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET	0xe00000
 
 /* Carve out a DDR region which will not be used by u-boot/Linux */
 #if defined(CONFIG_FSL_MC_ENET) || defined(CONFIG_FSL_DEBUG_SERVER)
 #define CONFIG_SYS_MEM_TOP_HIDE		get_dram_size_to_hide()
 #endif
 
+/* PCIe */
+#define CONFIG_PCIE1		/* PCIE controler 1 */
+#define CONFIG_PCIE2		/* PCIE controler 2 */
+#define CONFIG_PCIE3		/* PCIE controler 3 */
+#define CONFIG_PCIE4		/* PCIE controler 4 */
+#define FSL_PCIE_COMPAT "fsl,20851a-pcie"
+
+#define CONFIG_SYS_PCI_64BIT
+
+#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF	0x00000000
+#define CONFIG_SYS_PCIE_CFG0_SIZE	0x00001000	/* 4k */
+#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF	0x00001000
+#define CONFIG_SYS_PCIE_CFG1_SIZE	0x00001000	/* 4k */
+
+#define CONFIG_SYS_PCIE_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE_IO_PHYS_OFF	0x00010000
+#define CONFIG_SYS_PCIE_IO_SIZE		0x00010000	/* 64k */
+
+#define CONFIG_SYS_PCIE_MEM_BUS		0x40000000
+#define CONFIG_SYS_PCIE_MEM_PHYS_OFF	0x40000000
+#define CONFIG_SYS_PCIE_MEM_SIZE	0x40000000	/* 1G */
+
 /* Command line configuration */
 #define CONFIG_CMD_CACHE
 #define CONFIG_CMD_BDI
@@ -241,6 +166,7 @@
 #define CONFIG_CMD_ENV
 #define CONFIG_CMD_FLASH
 #define CONFIG_CMD_IMI
+#define CONFIG_CMD_LOADB
 #define CONFIG_CMD_MEMORY
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NET
@@ -260,8 +186,6 @@
 /* Physical Memory Map */
 /* fixme: these need to be checked against the board */
 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
-#define CONFIG_SYS_CLK_FREQ	100000000
-#define CONFIG_DDR_CLK_FREQ	133333333
 
 #define CONFIG_NR_DRAM_BANKS		3
 
@@ -277,7 +201,7 @@
 	"kernel_addr=0x100000\0"		\
 	"ramdisk_addr=0x800000\0"		\
 	"ramdisk_size=0x2000000\0"		\
-	"fdt_high=0xffffffffffffffff\0"		\
+	"fdt_high=0xa0000000\0"			\
 	"initrd_high=0xffffffffffffffff\0"	\
 	"kernel_start=0x581200000\0"		\
 	"kernel_load=0xa0000000\0"		\
@@ -292,13 +216,9 @@
 					"$kernel_size && bootm $kernel_load"
 #define CONFIG_BOOTDELAY		1
 
-/* Store environment at top of flash */
-#define CONFIG_ENV_IS_NOWHERE		1
-#define CONFIG_ENV_SIZE			0x1000
-
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
-#define CONFIG_SYS_PROMPT		"> "
+#define CONFIG_SYS_PROMPT		"=> "
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_HUSH_PARSER
@@ -306,10 +226,13 @@
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE /* Boot args buffer */
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_CMDLINE_EDITING		1
+#define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_MAXARGS		64	/* max command args */
 
 #ifndef __ASSEMBLY__
 unsigned long get_dram_size_to_hide(void);
 #endif
 
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
 #endif /* __LS2_COMMON_H */