blackfin: Move blackfin serial driver out of blackfin arch folder.

- Move blackfin serial driver to the generic driver folder.
- Move blackfin serial headers to blackfin arch head folder.
- Update the include path to blackfin serial header in start up code.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

2 files changed, 412 insertions, 0 deletions

diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index fbc4e97e98..442b7ea0df 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -52,6 +52,7 @@ COBJS-$(CONFIG_XILINX_UARTLITE) += serial_xuartlite.o
 COBJS-$(CONFIG_SANDBOX_SERIAL) += sandbox.o
 COBJS-$(CONFIG_SCIF_CONSOLE) += serial_sh.o
 COBJS-$(CONFIG_ZYNQ_SERIAL) += serial_zynq.o
+COBJS-$(CONFIG_BFIN_SERIAL) += serial_bfin.o
 
 ifndef CONFIG_SPL_BUILD
 COBJS-$(CONFIG_USB_TTY) += usbtty.o
diff --git a/drivers/serial/serial_bfin.c b/drivers/serial/serial_bfin.c
new file mode 100644
index 0000000000..0443b8427a
--- /dev/null
+++ b/drivers/serial/serial_bfin.c
@@ -0,0 +1,411 @@
+/*
+ * U-boot - serial.c Blackfin Serial Driver
+ *
+ * Copyright (c) 2005-2008 Analog Devices Inc.
+ *
+ * Copyright (c) 2003	Bas Vermeulen <bas@buyways.nl>,
+ *			BuyWays B.V. (www.buyways.nl)
+ *
+ * Based heavily on:
+ * blkfinserial.c: Serial driver for BlackFin DSP internal USRTs.
+ * Copyright(c) 2003	Metrowerks	<mwaddel@metrowerks.com>
+ * Copyright(c)	2001	Tony Z. Kou	<tonyko@arcturusnetworks.com>
+ * Copyright(c)	2001-2002 Arcturus Networks Inc. <www.arcturusnetworks.com>
+ *
+ * Based on code from 68328 version serial driver imlpementation which was:
+ * Copyright (C) 1995       David S. Miller    <davem@caip.rutgers.edu>
+ * Copyright (C) 1998       Kenneth Albanowski <kjahds@kjahds.com>
+ * Copyright (C) 1998, 1999 D. Jeff Dionne     <jeff@uclinux.org>
+ * Copyright (C) 1999       Vladimir Gurevich  <vgurevic@cisco.com>
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+/* Anomaly notes:
+ *  05000086 - we don't support autobaud
+ *  05000099 - we only use DR bit, so losing others is not a problem
+ *  05000100 - we don't use the UART_IIR register
+ *  05000215 - we poll the uart (no dma/interrupts)
+ *  05000225 - no workaround possible, but this shouldnt cause errors ...
+ *  05000230 - we tweak the baud rate calculation slightly
+ *  05000231 - we always use 1 stop bit
+ *  05000309 - we always enable the uart before we modify it in anyway
+ *  05000350 - we always enable the uart regardless of boot mode
+ *  05000363 - we don't support break signals, so don't generate one
+ */
+
+#include <common.h>
+#include <post.h>
+#include <watchdog.h>
+#include <serial.h>
+#include <linux/compiler.h>
+#include <asm/blackfin.h>
+#include <asm/serial.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_UART_CONSOLE
+
+#ifdef CONFIG_DEBUG_SERIAL
+static uart_lsr_t cached_lsr[256];
+static uart_lsr_t cached_rbr[256];
+static size_t cache_count;
+
+/* The LSR is read-to-clear on some parts, so we have to make sure status
+ * bits aren't inadvertently lost when doing various tests.  This also
+ * works around anomaly 05000099 at the same time by keeping a cumulative
+ * tally of all the status bits.
+ */
+static uart_lsr_t uart_lsr_save;
+static uart_lsr_t uart_lsr_read(uint32_t uart_base)
+{
+	uart_lsr_t lsr = _lsr_read(pUART);
+	uart_lsr_save |= (lsr & (OE|PE|FE|BI));
+	return lsr | uart_lsr_save;
+}
+/* Just do the clear for everyone since it can't hurt. */
+static void uart_lsr_clear(uint32_t uart_base)
+{
+	uart_lsr_save = 0;
+	_lsr_write(pUART, -1);
+}
+#else
+/* When debugging is disabled, we only care about the DR bit, so if other
+ * bits get set/cleared, we don't really care since we don't read them
+ * anyways (and thus anomaly 05000099 is irrelevant).
+ */
+static inline uart_lsr_t uart_lsr_read(uint32_t uart_base)
+{
+	return _lsr_read(pUART);
+}
+static void uart_lsr_clear(uint32_t uart_base)
+{
+	_lsr_write(pUART, -1);
+}
+#endif
+
+static void uart_putc(uint32_t uart_base, const char c)
+{
+	/* send a \r for compatibility */
+	if (c == '\n')
+		serial_putc('\r');
+
+	WATCHDOG_RESET();
+
+	/* wait for the hardware fifo to clear up */
+	while (!(uart_lsr_read(uart_base) & THRE))
+		continue;
+
+	/* queue the character for transmission */
+	bfin_write(&pUART->thr, c);
+	SSYNC();
+
+	WATCHDOG_RESET();
+}
+
+static int uart_tstc(uint32_t uart_base)
+{
+	WATCHDOG_RESET();
+	return (uart_lsr_read(uart_base) & DR) ? 1 : 0;
+}
+
+static int uart_getc(uint32_t uart_base)
+{
+	uint16_t uart_rbr_val;
+
+	/* wait for data ! */
+	while (!uart_tstc(uart_base))
+		continue;
+
+	/* grab the new byte */
+	uart_rbr_val = bfin_read(&pUART->rbr);
+
+#ifdef CONFIG_DEBUG_SERIAL
+	/* grab & clear the LSR */
+	uart_lsr_t uart_lsr_val = uart_lsr_read(uart_base);
+
+	cached_lsr[cache_count] = uart_lsr_val;
+	cached_rbr[cache_count] = uart_rbr_val;
+	cache_count = (cache_count + 1) % ARRAY_SIZE(cached_lsr);
+
+	if (uart_lsr_val & (OE|PE|FE|BI)) {
+		printf("\n[SERIAL ERROR]\n");
+		do {
+			--cache_count;
+			printf("\t%3zu: RBR=0x%02x LSR=0x%02x\n", cache_count,
+				cached_rbr[cache_count], cached_lsr[cache_count]);
+		} while (cache_count > 0);
+		return -1;
+	}
+#endif
+	uart_lsr_clear(uart_base);
+
+	return uart_rbr_val;
+}
+
+#if CONFIG_POST & CONFIG_SYS_POST_UART
+# define LOOP(x) x
+#else
+# define LOOP(x)
+#endif
+
+#if BFIN_UART_HW_VER < 4
+
+LOOP(
+static void uart_loop(uint32_t uart_base, int state)
+{
+	u16 mcr;
+
+	/* Drain the TX fifo first so bytes don't come back */
+	while (!(uart_lsr_read(uart_base) & TEMT))
+		continue;
+
+	mcr = bfin_read(&pUART->mcr);
+	if (state)
+		mcr |= LOOP_ENA | MRTS;
+	else
+		mcr &= ~(LOOP_ENA | MRTS);
+	bfin_write(&pUART->mcr, mcr);
+}
+)
+
+#else
+
+LOOP(
+static void uart_loop(uint32_t uart_base, int state)
+{
+	u32 control;
+
+	/* Drain the TX fifo first so bytes don't come back */
+	while (!(uart_lsr_read(uart_base) & TEMT))
+		continue;
+
+	control = bfin_read(&pUART->control);
+	if (state)
+		control |= LOOP_ENA | MRTS;
+	else
+		control &= ~(LOOP_ENA | MRTS);
+	bfin_write(&pUART->control, control);
+}
+)
+
+#endif
+
+static inline void __serial_set_baud(uint32_t uart_base, uint32_t baud)
+{
+#ifdef CONFIG_DEBUG_EARLY_SERIAL
+	serial_early_set_baud(uart_base, baud);
+#else
+	uint16_t divisor = (get_uart_clk() + (baud * 8)) / (baud * 16)
+			- ANOMALY_05000230;
+
+	/* Program the divisor to get the baud rate we want */
+	serial_set_divisor(uart_base, divisor);
+#endif
+}
+
+static void uart_puts(uint32_t uart_base, const char *s)
+{
+	while (*s)
+		uart_putc(uart_base, *s++);
+}
+
+#define DECL_BFIN_UART(n) \
+static int uart##n##_init(void) \
+{ \
+	const unsigned short pins[] = { _P_UART(n, RX), _P_UART(n, TX), 0, }; \
+	peripheral_request_list(pins, "bfin-uart"); \
+	uart_init(MMR_UART(n)); \
+	__serial_set_baud(MMR_UART(n), gd->baudrate); \
+	uart_lsr_clear(MMR_UART(n)); \
+	return 0; \
+} \
+\
+static int uart##n##_uninit(void) \
+{ \
+	return serial_early_uninit(MMR_UART(n)); \
+} \
+\
+static void uart##n##_setbrg(void) \
+{ \
+	__serial_set_baud(MMR_UART(n), gd->baudrate); \
+} \
+\
+static int uart##n##_getc(void) \
+{ \
+	return uart_getc(MMR_UART(n)); \
+} \
+\
+static int uart##n##_tstc(void) \
+{ \
+	return uart_tstc(MMR_UART(n)); \
+} \
+\
+static void uart##n##_putc(const char c) \
+{ \
+	uart_putc(MMR_UART(n), c); \
+} \
+\
+static void uart##n##_puts(const char *s) \
+{ \
+	uart_puts(MMR_UART(n), s); \
+} \
+\
+LOOP( \
+static void uart##n##_loop(int state) \
+{ \
+	uart_loop(MMR_UART(n), state); \
+} \
+) \
+\
+struct serial_device bfin_serial##n##_device = { \
+	.name   = "bfin_uart"#n, \
+	.start  = uart##n##_init, \
+	.stop   = uart##n##_uninit, \
+	.setbrg = uart##n##_setbrg, \
+	.getc   = uart##n##_getc, \
+	.tstc   = uart##n##_tstc, \
+	.putc   = uart##n##_putc, \
+	.puts   = uart##n##_puts, \
+	LOOP(.loop = uart##n##_loop) \
+};
+
+#ifdef UART0_RBR
+DECL_BFIN_UART(0)
+#endif
+#ifdef UART1_RBR
+DECL_BFIN_UART(1)
+#endif
+#ifdef UART2_RBR
+DECL_BFIN_UART(2)
+#endif
+#ifdef UART3_RBR
+DECL_BFIN_UART(3)
+#endif
+
+__weak struct serial_device *default_serial_console(void)
+{
+#if CONFIG_UART_CONSOLE == 0
+	return &bfin_serial0_device;
+#elif CONFIG_UART_CONSOLE == 1
+	return &bfin_serial1_device;
+#elif CONFIG_UART_CONSOLE == 2
+	return &bfin_serial2_device;
+#elif CONFIG_UART_CONSOLE == 3
+	return &bfin_serial3_device;
+#endif
+}
+
+void bfin_serial_initialize(void)
+{
+#ifdef UART0_RBR
+	serial_register(&bfin_serial0_device);
+#endif
+#ifdef UART1_RBR
+	serial_register(&bfin_serial1_device);
+#endif
+#ifdef UART2_RBR
+	serial_register(&bfin_serial2_device);
+#endif
+#ifdef UART3_RBR
+	serial_register(&bfin_serial3_device);
+#endif
+}
+
+#ifdef CONFIG_DEBUG_EARLY_SERIAL
+inline void uart_early_putc(uint32_t uart_base, const char c)
+{
+	/* send a \r for compatibility */
+	if (c == '\n')
+		uart_early_putc(uart_base, '\r');
+
+	/* wait for the hardware fifo to clear up */
+	while (!(_lsr_read(pUART) & THRE))
+		continue;
+
+	/* queue the character for transmission */
+	bfin_write(&pUART->thr, c);
+	SSYNC();
+}
+
+void uart_early_puts(const char *s)
+{
+	while (*s)
+		uart_early_putc(UART_BASE, *s++);
+}
+
+/* Symbol for our assembly to call. */
+void _serial_early_set_baud(uint32_t baud)
+{
+	serial_early_set_baud(UART_BASE, baud);
+}
+
+/* Symbol for our assembly to call. */
+void _serial_early_init(void)
+{
+	serial_early_init(UART_BASE);
+}
+#endif
+
+#elif defined(CONFIG_UART_MEM)
+
+char serial_logbuf[CONFIG_UART_MEM];
+char *serial_logbuf_head = serial_logbuf;
+
+int serial_mem_init(void)
+{
+	serial_logbuf_head = serial_logbuf;
+	return 0;
+}
+
+void serial_mem_setbrg(void)
+{
+}
+
+int serial_mem_tstc(void)
+{
+	return 0;
+}
+
+int serial_mem_getc(void)
+{
+	return 0;
+}
+
+void serial_mem_putc(const char c)
+{
+	*serial_logbuf_head = c;
+	if (++serial_logbuf_head == serial_logbuf + CONFIG_UART_MEM)
+		serial_logbuf_head = serial_logbuf;
+}
+
+void serial_mem_puts(const char *s)
+{
+	while (*s)
+		serial_putc(*s++);
+}
+
+struct serial_device bfin_serial_mem_device = {
+	.name   = "bfin_uart_mem",
+	.start  = serial_mem_init,
+	.setbrg = serial_mem_setbrg,
+	.getc   = serial_mem_getc,
+	.tstc   = serial_mem_tstc,
+	.putc   = serial_mem_putc,
+	.puts   = serial_mem_puts,
+};
+
+
+__weak struct serial_device *default_serial_console(void)
+{
+	return &bfin_serial_mem_device;
+}
+
+void bfin_serial_initialize(void)
+{
+	serial_register(&bfin_serial_mem_device);
+}
+#endif /* CONFIG_UART_MEM */