armv8: LS2080A: Rename LS2085A to reflect LS2080A

LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>

1 files changed, 0 insertions, 206 deletions

diff --git a/board/freescale/ls2085a/ddr.c b/board/freescale/ls2085a/ddr.c
deleted file mode 100644
index 4884fa24d0..0000000000
--- a/board/freescale/ls2085a/ddr.c
+++ /dev/null
@@ -1,206 +0,0 @@
-/*
- * Copyright 2014 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-#include "ddr.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void fsl_ddr_board_options(memctl_options_t *popts,
-				dimm_params_t *pdimm,
-				unsigned int ctrl_num)
-{
-	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
-	ulong ddr_freq;
-
-	if (ctrl_num > 3) {
-		printf("Not supported controller number %d\n", ctrl_num);
-		return;
-	}
-	if (!pdimm->n_ranks)
-		return;
-
-	/*
-	 * we use identical timing for all slots. If needed, change the code
-	 * to  pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
-	 */
-	if (popts->registered_dimm_en)
-		pbsp = rdimms[ctrl_num];
-	else
-		pbsp = udimms[ctrl_num];
-
-
-	/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
-	 * freqency and n_banks specified in board_specific_parameters table.
-	 */
-	ddr_freq = get_ddr_freq(0) / 1000000;
-	while (pbsp->datarate_mhz_high) {
-		if (pbsp->n_ranks == pdimm->n_ranks &&
-		    (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
-			if (ddr_freq <= pbsp->datarate_mhz_high) {
-				popts->clk_adjust = pbsp->clk_adjust;
-				popts->wrlvl_start = pbsp->wrlvl_start;
-				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
-				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
-				goto found;
-			}
-			pbsp_highest = pbsp;
-		}
-		pbsp++;
-	}
-
-	if (pbsp_highest) {
-		printf("Error: board specific timing not found for data rate %lu MT/s\n"
-			"Trying to use the highest speed (%u) parameters\n",
-			ddr_freq, pbsp_highest->datarate_mhz_high);
-		popts->clk_adjust = pbsp_highest->clk_adjust;
-		popts->wrlvl_start = pbsp_highest->wrlvl_start;
-		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
-		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
-	} else {
-		panic("DIMM is not supported by this board");
-	}
-found:
-	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
-		"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
-		pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
-		pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
-		pbsp->wrlvl_ctl_3);
-
-	if (ctrl_num == CONFIG_DP_DDR_CTRL) {
-		/* force DDR bus width to 32 bits */
-		popts->data_bus_width = 1;
-		popts->otf_burst_chop_en = 0;
-		popts->burst_length = DDR_BL8;
-		popts->bstopre = 0;	/* enable auto precharge */
-	}
-	/*
-	 * Factors to consider for half-strength driver enable:
-	 *	- number of DIMMs installed
-	 */
-	popts->half_strength_driver_enable = 1;
-	/*
-	 * Write leveling override
-	 */
-	popts->wrlvl_override = 1;
-	popts->wrlvl_sample = 0xf;
-
-	/*
-	 * Rtt and Rtt_WR override
-	 */
-	popts->rtt_override = 0;
-
-	/* Enable ZQ calibration */
-	popts->zq_en = 1;
-
-#ifdef CONFIG_SYS_FSL_DDR4
-	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
-	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
-			  DDR_CDR2_VREF_OVRD(70);	/* Vref = 70% */
-#else
-	/* DHC_EN =1, ODT = 75 Ohm */
-	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
-	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
-#endif
-}
-
-#ifdef CONFIG_SYS_DDR_RAW_TIMING
-dimm_params_t ddr_raw_timing = {
-	.n_ranks = 2,
-	.rank_density = 1073741824u,
-	.capacity = 2147483648,
-	.primary_sdram_width = 64,
-	.ec_sdram_width = 0,
-	.registered_dimm = 0,
-	.mirrored_dimm = 0,
-	.n_row_addr = 14,
-	.n_col_addr = 10,
-	.n_banks_per_sdram_device = 8,
-	.edc_config = 0,
-	.burst_lengths_bitmask = 0x0c,
-
-	.tckmin_x_ps = 937,
-	.caslat_x = 0x6FC << 4,  /* 14,13,11,10,9,8,7,6 */
-	.taa_ps = 13090,
-	.twr_ps = 15000,
-	.trcd_ps = 13090,
-	.trrd_ps = 5000,
-	.trp_ps = 13090,
-	.tras_ps = 33000,
-	.trc_ps = 46090,
-	.trfc_ps = 160000,
-	.twtr_ps = 7500,
-	.trtp_ps = 7500,
-	.refresh_rate_ps = 7800000,
-	.tfaw_ps = 25000,
-};
-
-int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
-		unsigned int controller_number,
-		unsigned int dimm_number)
-{
-	const char dimm_model[] = "Fixed DDR on board";
-
-	if (((controller_number == 0) && (dimm_number == 0)) ||
-	    ((controller_number == 1) && (dimm_number == 0))) {
-		memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
-		memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
-		memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
-	}
-
-	return 0;
-}
-#endif
-phys_size_t initdram(int board_type)
-{
-	phys_size_t dram_size;
-
-	puts("Initializing DDR....");
-
-	puts("using SPD\n");
-	dram_size = fsl_ddr_sdram();
-
-	return dram_size;
-}
-
-void dram_init_banksize(void)
-{
-#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
-	phys_size_t dp_ddr_size;
-#endif
-
-	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
-	if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
-		gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
-		gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
-		gd->bd->bi_dram[1].size = gd->ram_size -
-					  CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
-	} else {
-		gd->bd->bi_dram[0].size = gd->ram_size;
-	}
-
-#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
-	/* initialize DP-DDR here */
-	puts("DP-DDR:  ");
-	/*
-	 * DDR controller use 0 as the base address for binding.
-	 * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
-	 */
-	dp_ddr_size = fsl_other_ddr_sdram(CONFIG_SYS_DP_DDR_BASE_PHY,
-					  CONFIG_DP_DDR_CTRL,
-					  CONFIG_DP_DDR_NUM_CTRLS,
-					  CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR,
-					  NULL, NULL, NULL);
-	if (dp_ddr_size) {
-		gd->bd->bi_dram[2].start = CONFIG_SYS_DP_DDR_BASE;
-		gd->bd->bi_dram[2].size = dp_ddr_size;
-	} else {
-		puts("Not detected");
-	}
-#endif
-}