ARM: add assembly routine to switch to non-secure state

While actually switching to non-secure state is one thing, another
part of this process is to make sure that we still have full access
to the interrupt controller (GIC).
The GIC is fully aware of secure vs. non-secure state, some
registers are banked, others may be configured to be accessible from
secure state only.
To be as generic as possible, we get the GIC memory mapped address
based on the PERIPHBASE value in the CBAR register. Since this
register is not architecturally defined, we check the MIDR before to
be from an A15 or A7.
For CPUs not having the CBAR or boards with wrong information herein
we allow providing the base address as a configuration variable.

Now that we know the GIC address, we:
a) allow private interrupts to be delivered to the core
   (GICD_IGROUPR0 = 0xFFFFFFFF)
b) enable the CPU interface (GICC_CTLR[0] = 1)
c) set the priority filter to allow non-secure interrupts
   (GICC_PMR = 0xFF)

Also we allow access to all coprocessor interfaces from non-secure
state by writing the appropriate bits in the NSACR register.

The generic timer base frequency register is only accessible from
secure state, so we have to program it now. Actually this should be
done from primary firmware before, but some boards seems to omit
this, so if needed we do this here with a board specific value.
The Versatile Express board does not need this, so we remove the
frequency from the configuration file here.

After having switched to non-secure state, we also enable the
non-secure GIC CPU interface, since this register is banked.

Since we need to call this routine also directly from the smp_pen
later (where we don't have any stack), we can only use caller saved
registers r0-r3 and r12 to not mess with the compiler.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>

1 files changed, 21 insertions, 0 deletions

diff --git a/arch/arm/include/asm/armv7.h b/arch/arm/include/asm/armv7.h
index 0f7cbbfc12..3dcfc8fb29 100644
--- a/arch/arm/include/asm/armv7.h
+++ b/arch/arm/include/asm/armv7.h
@@ -18,6 +18,22 @@
 #define MIDR_CORTEX_A15_R0P0	0x410FC0F0
 #define MIDR_CORTEX_A15_R2P2	0x412FC0F2
 
+/* Cortex-A7 revisions */
+#define MIDR_CORTEX_A7_R0P0	0x410FC070
+
+#define MIDR_PRIMARY_PART_MASK	0xFF0FFFF0
+
+/* ID_PFR1 feature fields */
+#define CPUID_ARM_SEC_SHIFT		4
+#define CPUID_ARM_SEC_MASK		(0xF << CPUID_ARM_SEC_SHIFT)
+#define CPUID_ARM_VIRT_SHIFT		12
+#define CPUID_ARM_VIRT_MASK		(0xF << CPUID_ARM_VIRT_SHIFT)
+#define CPUID_ARM_GENTIMER_SHIFT	16
+#define CPUID_ARM_GENTIMER_MASK		(0xF << CPUID_ARM_GENTIMER_SHIFT)
+
+/* valid bits in CBAR register / PERIPHBASE value */
+#define CBAR_MASK			0xFFFF8000
+
 /* CCSIDR */
 #define CCSIDR_LINE_SIZE_OFFSET		0
 #define CCSIDR_LINE_SIZE_MASK		0x7
@@ -60,6 +76,11 @@ void v7_outer_cache_inval_all(void);
 void v7_outer_cache_flush_range(u32 start, u32 end);
 void v7_outer_cache_inval_range(u32 start, u32 end);
 
+#ifdef CONFIG_ARMV7_NONSEC
+/* defined in assembly file */
+unsigned int _nonsec_init(void);
+#endif /* CONFIG_ARMV7_NONSEC */
+
 #endif /* ! __ASSEMBLY__ */
 
 #endif