Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm: (146 commits)
  arm: Use common .lds file where possible
  arm: add a common .lds link script
  arm: Remove unneeded setting of LDCSRIPT
  Define CPUDIR for the .lds link script
  arm: Remove zipitz2 link script
  Allow arch directory to contain .lds without requiring Makefile
  OMAP: Remove omap1610inn-based boards
  arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix build warnings
  board/ti/beagle/beagle.c: Fix build warnings
  sdrc.c: Fix typo in do_sdrc_init() for SPL
  tegra: i2c: Add I2C driver
  tegra: fdt: i2c: Add extra I2C bindings for U-Boot
  tegra: i2c: Select I2C ordering for Seaboard
  tegra: i2c: Enable I2C on Seaboard
  tegra: i2c: Select number of controllers for Tegra2 boards
  tegra: i2c: Initialise I2C on Nvidia boards
  tegra: Enhance clock support to handle 16-bit clock divisors
  fdt: Add function to allow aliases to refer to multiple nodes
  tegra: Rename NV_PA_PMC_BASE to TEGRA2_PMC_BASE
  tegra: fdt: Enable FDT support for Ventana
  tegra: fdt: Enable FDT support for Seaboard
  tegra: usb: Enable USB on Seaboard
  tegra: usb: Add common USB defines for tegra2 boards
  tegra: usb: Add USB support to nvidia boards
  arm: Check for valid FDT after console is up
  fdt: Avoid early panic() when there is no FDT present
  tegra: usb: Add support for Tegra USB peripheral
  tegra: fdt: Add function to return peripheral/clock ID
  usb: Add support for txfifo threshold
  tegra: usb: fdt: Add USB definitions for Tegra2 Seaboard
  tegra: usb: fdt: Add additional device tree definitions for USB ports
  tegra: fdt: Add clock bindings for Tegra2 Seaboard
  tegra: fdt: Add clock bindings
  tegra: fdt: Add additional USB binding
  fdt: Add tegra-usb bindings file from linux
  fdt: Add staging area for device tree binding documentation
  tegra: fdt: Add device tree file for Tegra2 Seaboard from kernel
  tegra: fdt: Add Tegra2x device tree file from kernel
  arm: fdt: Add skeleton device tree file from kernel
  fdt: Add basic support for decoding GPIO definitions
  fdt: Add functions to access phandles, arrays and bools
  fdt: Tidy up a few fdtdec problems
  fdt: Add tests for fdtdec
  fdt: Add fdtdec_find_aliases() to deal with alias nodes
  arm: Tegra2: Fix ELDK42 gcc failure with inline asm stack pointer load
  net: fec_mxc: allow use with cache enabled
  net: force PKTALIGN to ARCH_DMA_MINALIGN
  i.MX28: Enable caches by default
  i.MX28: Make use of the bounce buffer
  i.MX28: Do data transfers via DMA in MMC driver
  MMC: Implement generic bounce buffer
  i.MX28: Add cache support to MXS NAND driver
  i.MX28: Add cache support into the APBH DMA driver
  ARM926EJS: Implement cache operations
  board/vpac270/onenand.c: Fix build errors
  nhk8815: fix build errors
  atmel-boards: add missing atmel_mci.h
  ARM: highbank: setup env from boot source register
  ARM: highbank: change env config to use nvram
  ARM: highbank: add reset support
  ARM: highbank: Add boot counter support
  ARM: highbank: change TEXT_BASE to 0x8000
  ARM: highbank: fix us_to_tick calculation
  ARM: highbank: add missing get_tbclk
  ARM: highbank: fix warning for calxedaxgmac_initialize
  net: calxedaxgmac: fix build due to missing __aligned definition
  EXYNOS: Add structure for Exynos4 DMC
  EXYNOS: SMDK5250: Support all 4 UARTs
  ARM: fix s3c2410 timer code
  ARM: davinci: fixes for cam_enc_4xx board
  omap3_spi: receive transmit mode
  calimain, enbw_cmc: Fix typo in comments
  Davinci: ea20: use gpio framework to access gpios
  OMAP3: mt_ventoux: sets its own mtdparts
  OMAP3: mt_ventoux: updated timing for FPGA
  twl4030: fix potential power supply handling issues
  NAND: TI: fix warnings in omap_gpmc.c
  cam_enc_4xx: Rename 'images' to 'imgs'
  arm: Add Prep subcommand support to bootm
  OMAP3: twister: add support to boot Linux from SPL
  SPL: call cleanup_before_linux() before booting Linux
  OMAP3: SPL: do not call I2C init if no I2C is set.
  Add cache functions to SPL for armv7
  devkit8000: Implement and activate direct OS boot
  omap/spl: change output of spl_parse_image_header
  omap-common/spl: Add linux boot to SPL
  devkit8000/spl: init GPMC for dm9000 in SPL
  omap-common: Add NAND SPL linux booting
  devkit8000: add config for spl command
  Add cmd_spl command
  mx53ard: Initialize return code with error
  mx53: Make PLL2 to be the parent of UART clock
  configs: imx: Use CONFIG_SF_DEFAULT_CS
  mx28evk: Provide default values for SPI bus and chip select
  USB: ehci-mx6: Add proper IO accessors
  mx6: Read silicon revision from register
  i.MX28: Drop __naked function from spl_mem_init
  mxs_spi: Return proper timeout error
  i.MX28: Make the stabilization delays shorter
  pmic_i2c: Return error in case of invalid pmic_i2c_tx_num
  mx6: Remove duplicate definition of ANATOP_BASE_ADDR
  mx6: Fix reset cause for Power On Reset case
  i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITE
  i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG
  i.MX28: Enable additional DRAM address bits
  mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use for environment
  mx31: add "ARM11P power gating" to get_reset_cause
  mx31pdk: Fix CONFIG_SYS_MEMTEST_END
  efikamx: Fix CONFIG_SYS_MEMTEST_END
  mx53smd: Fix CONFIG_SYS_MEMTEST_END
  mx53evk: Fix CONFIG_SYS_MEMTEST_END
  mx51evk: Fix CONFIG_SYS_MEMTEST_END
  i.MX6: mx6qsabrelite: add ext2 support
  imximage: Remove overwriting of flash_offset
  IXP: Fix GPIO_INT_ACT_LOW_SET()
  IXP: Fix NAND build warning on PDNB3 and SCPU
  IXP: Move PDNB3 and SCPU from Makefile to boards.cfg
  IXP: Squash warnings in IXP NPE
  IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST}
  IXP: Make IXP buildable with arm-linux- toolchains
  Examples: Properly append LDFLAGS to LD command
  SPL: Enable YMODEM support on BeagleBone and AM335x EVM
  SPL: Add YMODEM over UART load support
  SPL: Add README.omap3
  README: document more SPL config options
  spl.c: Use __noreturn decorator
  config.mk: Check for -fstack-usage support
  config.mk: Make cc-option create a file under include/generated
  ...

1 files changed, 460 insertions, 0 deletions

diff --git a/arch/arm/cpu/armv7/tegra2/usb.c b/arch/arm/cpu/armv7/tegra2/usb.c
new file mode 100644
index 0000000000..c80de7f6a3
--- /dev/null
+++ b/arch/arm/cpu/armv7/tegra2/usb.c
@@ -0,0 +1,460 @@
+/*
+ * Copyright (c) 2011 The Chromium OS Authors.
+ * (C) Copyright 2010,2011 NVIDIA Corporation <www.nvidia.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm-generic/gpio.h>
+#include <asm/arch/tegra2.h>
+#include <asm/arch/clk_rst.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/uart.h>
+#include <asm/arch/usb.h>
+#include <libfdt.h>
+#include <fdtdec.h>
+
+enum {
+	USB_PORTS_MAX	= 4,			/* Maximum ports we allow */
+};
+
+/* Parameters we need for USB */
+enum {
+	PARAM_DIVN,                     /* PLL FEEDBACK DIVIDer */
+	PARAM_DIVM,                     /* PLL INPUT DIVIDER */
+	PARAM_DIVP,                     /* POST DIVIDER (2^N) */
+	PARAM_CPCON,                    /* BASE PLLC CHARGE Pump setup ctrl */
+	PARAM_LFCON,                    /* BASE PLLC LOOP FILter setup ctrl */
+	PARAM_ENABLE_DELAY_COUNT,       /* PLL-U Enable Delay Count */
+	PARAM_STABLE_COUNT,             /* PLL-U STABLE count */
+	PARAM_ACTIVE_DELAY_COUNT,       /* PLL-U Active delay count */
+	PARAM_XTAL_FREQ_COUNT,          /* PLL-U XTAL frequency count */
+	PARAM_DEBOUNCE_A_TIME,          /* 10MS DELAY for BIAS_DEBOUNCE_A */
+	PARAM_BIAS_TIME,                /* 20US DELAY AFter bias cell op */
+
+	PARAM_COUNT
+};
+
+/* Possible port types (dual role mode) */
+enum dr_mode {
+	DR_MODE_NONE = 0,
+	DR_MODE_HOST,		/* supports host operation */
+	DR_MODE_DEVICE,		/* supports device operation */
+	DR_MODE_OTG,		/* supports both */
+};
+
+/* Information about a USB port */
+struct fdt_usb {
+	struct usb_ctlr *reg;	/* address of registers in physical memory */
+	unsigned utmi:1;	/* 1 if port has external tranceiver, else 0 */
+	unsigned enabled:1;	/* 1 to enable, 0 to disable */
+	unsigned has_legacy_mode:1; /* 1 if this port has legacy mode */
+	enum dr_mode dr_mode;	/* dual role mode */
+	enum periph_id periph_id;/* peripheral id */
+	struct fdt_gpio_state vbus_gpio;	/* GPIO for vbus enable */
+};
+
+static struct fdt_usb port[USB_PORTS_MAX];	/* List of valid USB ports */
+static unsigned port_count;			/* Number of available ports */
+static int port_current;			/* Current port (-1 = none) */
+
+/*
+ * This table has USB timing parameters for each Oscillator frequency we
+ * support. There are four sets of values:
+ *
+ * 1. PLLU configuration information (reference clock is osc/clk_m and
+ * PLLU-FOs are fixed at 12MHz/60MHz/480MHz).
+ *
+ *  Reference frequency     13.0MHz      19.2MHz      12.0MHz      26.0MHz
+ *  ----------------------------------------------------------------------
+ *      DIVN                960 (0x3c0)  200 (0c8)    960 (3c0h)   960 (3c0)
+ *      DIVM                13 (0d)      4 (04)       12 (0c)      26 (1a)
+ * Filter frequency (MHz)   1            4.8          6            2
+ * CPCON                    1100b        0011b        1100b        1100b
+ * LFCON0                   0            0            0            0
+ *
+ * 2. PLL CONFIGURATION & PARAMETERS for different clock generators:
+ *
+ * Reference frequency     13.0MHz         19.2MHz         12.0MHz     26.0MHz
+ * ---------------------------------------------------------------------------
+ * PLLU_ENABLE_DLY_COUNT   02 (0x02)       03 (03)         02 (02)     04 (04)
+ * PLLU_STABLE_COUNT       51 (33)         75 (4B)         47 (2F)    102 (66)
+ * PLL_ACTIVE_DLY_COUNT    05 (05)         06 (06)         04 (04)     09 (09)
+ * XTAL_FREQ_COUNT        127 (7F)        187 (BB)        118 (76)    254 (FE)
+ *
+ * 3. Debounce values IdDig, Avalid, Bvalid, VbusValid, VbusWakeUp, and
+ * SessEnd. Each of these signals have their own debouncer and for each of
+ * those one out of two debouncing times can be chosen (BIAS_DEBOUNCE_A or
+ * BIAS_DEBOUNCE_B).
+ *
+ * The values of DEBOUNCE_A and DEBOUNCE_B are calculated as follows:
+ *    0xffff -> No debouncing at all
+ *    <n> ms = <n> *1000 / (1/19.2MHz) / 4
+ *
+ * So to program a 1 ms debounce for BIAS_DEBOUNCE_A, we have:
+ * BIAS_DEBOUNCE_A[15:0] = 1000 * 19.2 / 4  = 4800 = 0x12c0
+ *
+ * We need to use only DebounceA for BOOTROM. We don't need the DebounceB
+ * values, so we can keep those to default.
+ *
+ * 4. The 20 microsecond delay after bias cell operation.
+ */
+static const unsigned usb_pll[CLOCK_OSC_FREQ_COUNT][PARAM_COUNT] = {
+	/* DivN, DivM, DivP, CPCON, LFCON, Delays             Debounce, Bias */
+	{ 0x3C0, 0x0D, 0x00, 0xC,   0,  0x02, 0x33, 0x05, 0x7F, 0x7EF4, 5 },
+	{ 0x0C8, 0x04, 0x00, 0x3,   0,  0x03, 0x4B, 0x06, 0xBB, 0xBB80, 7 },
+	{ 0x3C0, 0x0C, 0x00, 0xC,   0,  0x02, 0x2F, 0x04, 0x76, 0x7530, 5 },
+	{ 0x3C0, 0x1A, 0x00, 0xC,   0,  0x04, 0x66, 0x09, 0xFE, 0xFDE8, 9 }
+};
+
+/* UTMIP Idle Wait Delay */
+static const u8 utmip_idle_wait_delay = 17;
+
+/* UTMIP Elastic limit */
+static const u8 utmip_elastic_limit = 16;
+
+/* UTMIP High Speed Sync Start Delay */
+static const u8 utmip_hs_sync_start_delay = 9;
+
+/* Put the port into host mode (this only works for OTG ports) */
+static void set_host_mode(struct fdt_usb *config)
+{
+	if (config->dr_mode == DR_MODE_OTG) {
+		/* Check whether remote host from USB1 is driving VBus */
+		if (readl(&config->reg->phy_vbus_sensors) & VBUS_VLD_STS)
+			return;
+
+		/*
+		 * If not driving, we set the GPIO to enable VBUS. We assume
+		 * that the pinmux is set up correctly for this.
+		 */
+		if (fdt_gpio_isvalid(&config->vbus_gpio)) {
+			fdtdec_setup_gpio(&config->vbus_gpio);
+			gpio_direction_output(config->vbus_gpio.gpio, 1);
+			debug("set_host_mode: GPIO %d high\n",
+			      config->vbus_gpio.gpio);
+		}
+	}
+}
+
+void usbf_reset_controller(struct fdt_usb *config, struct usb_ctlr *usbctlr)
+{
+	/* Reset the USB controller with 2us delay */
+	reset_periph(config->periph_id, 2);
+
+	/*
+	 * Set USB1_NO_LEGACY_MODE to 1, Registers are accessible under
+	 * base address
+	 */
+	if (config->has_legacy_mode)
+		setbits_le32(&usbctlr->usb1_legacy_ctrl, USB1_NO_LEGACY_MODE);
+
+	/* Put UTMIP1/3 in reset */
+	setbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET);
+
+	/* Enable the UTMIP PHY */
+	if (config->utmi)
+		setbits_le32(&usbctlr->susp_ctrl, UTMIP_PHY_ENB);
+
+	/*
+	 * TODO: where do we take the USB1 out of reset? The old code would
+	 * take USB3 out of reset, but not USB1. This code doesn't do either.
+	 */
+}
+
+/* set up the USB controller with the parameters provided */
+static int init_usb_controller(struct fdt_usb *config,
+				struct usb_ctlr *usbctlr, const u32 timing[])
+{
+	u32 val;
+	int loop_count;
+
+	clock_enable(config->periph_id);
+
+	/* Reset the usb controller */
+	usbf_reset_controller(config, usbctlr);
+
+	/* Stop crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN low */
+	clrbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN);
+
+	/* Follow the crystal clock disable by >100ns delay */
+	udelay(1);
+
+	/*
+	 * To Use the A Session Valid for cable detection logic, VBUS_WAKEUP
+	 * mux must be switched to actually use a_sess_vld threshold.
+	 */
+	if (fdt_gpio_isvalid(&config->vbus_gpio)) {
+		clrsetbits_le32(&usbctlr->usb1_legacy_ctrl,
+			VBUS_SENSE_CTL_MASK,
+			VBUS_SENSE_CTL_A_SESS_VLD << VBUS_SENSE_CTL_SHIFT);
+	}
+
+	/*
+	 * PLL Delay CONFIGURATION settings. The following parameters control
+	 * the bring up of the plls.
+	 */
+	val = readl(&usbctlr->utmip_misc_cfg1);
+	clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK,
+		timing[PARAM_STABLE_COUNT] << UTMIP_PLLU_STABLE_COUNT_SHIFT);
+	clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK,
+		timing[PARAM_ACTIVE_DELAY_COUNT] <<
+			UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT);
+	writel(val, &usbctlr->utmip_misc_cfg1);
+
+	/* Set PLL enable delay count and crystal frequency count */
+	val = readl(&usbctlr->utmip_pll_cfg1);
+	clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK,
+		timing[PARAM_ENABLE_DELAY_COUNT] <<
+			UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT);
+	clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK,
+		timing[PARAM_XTAL_FREQ_COUNT] <<
+			UTMIP_XTAL_FREQ_COUNT_SHIFT);
+	writel(val, &usbctlr->utmip_pll_cfg1);
+
+	/* Setting the tracking length time */
+	clrsetbits_le32(&usbctlr->utmip_bias_cfg1,
+		UTMIP_BIAS_PDTRK_COUNT_MASK,
+		timing[PARAM_BIAS_TIME] << UTMIP_BIAS_PDTRK_COUNT_SHIFT);
+
+	/* Program debounce time for VBUS to become valid */
+	clrsetbits_le32(&usbctlr->utmip_debounce_cfg0,
+		UTMIP_DEBOUNCE_CFG0_MASK,
+		timing[PARAM_DEBOUNCE_A_TIME] << UTMIP_DEBOUNCE_CFG0_SHIFT);
+
+	setbits_le32(&usbctlr->utmip_tx_cfg0, UTMIP_FS_PREAMBLE_J);
+
+	/* Disable battery charge enabling bit */
+	setbits_le32(&usbctlr->utmip_bat_chrg_cfg0, UTMIP_PD_CHRG);
+
+	clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_XCVR_LSBIAS_SE);
+	setbits_le32(&usbctlr->utmip_spare_cfg0, FUSE_SETUP_SEL);
+
+	/*
+	 * Configure the UTMIP_IDLE_WAIT and UTMIP_ELASTIC_LIMIT
+	 * Setting these fields, together with default values of the
+	 * other fields, results in programming the registers below as
+	 * follows:
+	 *         UTMIP_HSRX_CFG0 = 0x9168c000
+	 *         UTMIP_HSRX_CFG1 = 0x13
+	 */
+
+	/* Set PLL enable delay count and Crystal frequency count */
+	val = readl(&usbctlr->utmip_hsrx_cfg0);
+	clrsetbits_le32(&val, UTMIP_IDLE_WAIT_MASK,
+		utmip_idle_wait_delay << UTMIP_IDLE_WAIT_SHIFT);
+	clrsetbits_le32(&val, UTMIP_ELASTIC_LIMIT_MASK,
+		utmip_elastic_limit << UTMIP_ELASTIC_LIMIT_SHIFT);
+	writel(val, &usbctlr->utmip_hsrx_cfg0);
+
+	/* Configure the UTMIP_HS_SYNC_START_DLY */
+	clrsetbits_le32(&usbctlr->utmip_hsrx_cfg1,
+		UTMIP_HS_SYNC_START_DLY_MASK,
+		utmip_hs_sync_start_delay << UTMIP_HS_SYNC_START_DLY_SHIFT);
+
+	/* Preceed the crystal clock disable by >100ns delay. */
+	udelay(1);
+
+	/* Resuscitate crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN */
+	setbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN);
+
+	/* Finished the per-controller init. */
+
+	/* De-assert UTMIP_RESET to bring out of reset. */
+	clrbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET);
+
+	/* Wait for the phy clock to become valid in 100 ms */
+	for (loop_count = 100000; loop_count != 0; loop_count--) {
+		if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID)
+			break;
+		udelay(1);
+	}
+	if (loop_count == 100000)
+		return -1;
+
+	return 0;
+}
+
+static void power_up_port(struct usb_ctlr *usbctlr)
+{
+	/* Deassert power down state */
+	clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_FORCE_PD_POWERDOWN |
+		UTMIP_FORCE_PD2_POWERDOWN | UTMIP_FORCE_PDZI_POWERDOWN);
+	clrbits_le32(&usbctlr->utmip_xcvr_cfg1, UTMIP_FORCE_PDDISC_POWERDOWN |
+		UTMIP_FORCE_PDCHRP_POWERDOWN | UTMIP_FORCE_PDDR_POWERDOWN);
+}
+
+static void config_clock(const u32 timing[])
+{
+	clock_start_pll(CLOCK_ID_USB,
+		timing[PARAM_DIVM], timing[PARAM_DIVN], timing[PARAM_DIVP],
+		timing[PARAM_CPCON], timing[PARAM_LFCON]);
+}
+
+/**
+ * Add a new USB port to the list of available ports.
+ *
+ * @param config	USB port configuration
+ * @return 0 if ok, -1 if error (too many ports)
+ */
+static int add_port(struct fdt_usb *config, const u32 timing[])
+{
+	struct usb_ctlr *usbctlr = config->reg;
+
+	if (port_count == USB_PORTS_MAX) {
+		debug("tegrausb: Cannot register more than %d ports\n",
+		      USB_PORTS_MAX);
+		return -1;
+	}
+	if (init_usb_controller(config, usbctlr, timing)) {
+		debug("tegrausb: Cannot init port\n");
+		return -1;
+	}
+	if (config->utmi) {
+		/* Disable ICUSB FS/LS transceiver */
+		clrbits_le32(&usbctlr->icusb_ctrl, IC_ENB1);
+
+		/* Select UTMI parallel interface */
+		clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK,
+				PTS_UTMI << PTS_SHIFT);
+		clrbits_le32(&usbctlr->port_sc1, STS);
+		power_up_port(usbctlr);
+	}
+	port[port_count++] = *config;
+
+	return 0;
+}
+
+int tegrausb_start_port(unsigned portnum, u32 *hccr, u32 *hcor)
+{
+	struct usb_ctlr *usbctlr;
+
+	if (portnum >= port_count)
+		return -1;
+	tegrausb_stop_port();
+	set_host_mode(&port[portnum]);
+
+	usbctlr = port[portnum].reg;
+	*hccr = (u32)&usbctlr->cap_length;
+	*hcor = (u32)&usbctlr->usb_cmd;
+	port_current = portnum;
+	return 0;
+}
+
+int tegrausb_stop_port(void)
+{
+	struct usb_ctlr *usbctlr;
+
+	if (port_current == -1)
+		return -1;
+
+	usbctlr = port[port_current].reg;
+
+	/* Stop controller */
+	writel(0, &usbctlr->usb_cmd);
+	udelay(1000);
+
+	/* Initiate controller reset */
+	writel(2, &usbctlr->usb_cmd);
+	udelay(1000);
+	port_current = -1;
+	return 0;
+}
+
+int fdt_decode_usb(const void *blob, int node, unsigned osc_frequency_mhz,
+		   struct fdt_usb *config)
+{
+	const char *phy, *mode;
+
+	config->reg = (struct usb_ctlr *)fdtdec_get_addr(blob, node, "reg");
+	mode = fdt_getprop(blob, node, "dr_mode", NULL);
+	if (mode) {
+		if (0 == strcmp(mode, "host"))
+			config->dr_mode = DR_MODE_HOST;
+		else if (0 == strcmp(mode, "peripheral"))
+			config->dr_mode = DR_MODE_DEVICE;
+		else if (0 == strcmp(mode, "otg"))
+			config->dr_mode = DR_MODE_OTG;
+		else {
+			debug("%s: Cannot decode dr_mode '%s'\n", __func__,
+			      mode);
+			return -FDT_ERR_NOTFOUND;
+		}
+	} else {
+		config->dr_mode = DR_MODE_HOST;
+	}
+
+	phy = fdt_getprop(blob, node, "phy_type", NULL);
+	config->utmi = phy && 0 == strcmp("utmi", phy);
+	config->enabled = fdtdec_get_is_enabled(blob, node);
+	config->has_legacy_mode = fdtdec_get_bool(blob, node,
+						  "nvidia,has-legacy-mode");
+	config->periph_id = clock_decode_periph_id(blob, node);
+	if (config->periph_id == PERIPH_ID_NONE) {
+		debug("%s: Missing/invalid peripheral ID\n", __func__);
+		return -FDT_ERR_NOTFOUND;
+	}
+	fdtdec_decode_gpio(blob, node, "nvidia,vbus-gpio", &config->vbus_gpio);
+	debug("enabled=%d, legacy_mode=%d, utmi=%d, periph_id=%d, vbus=%d, "
+	      "dr_mode=%d\n", config->enabled, config->has_legacy_mode,
+	      config->utmi, config->periph_id, config->vbus_gpio.gpio,
+	      config->dr_mode);
+
+	return 0;
+}
+
+int board_usb_init(const void *blob)
+{
+	struct fdt_usb config;
+	unsigned osc_freq = clock_get_rate(CLOCK_ID_OSC);
+	enum clock_osc_freq freq;
+	int node_list[USB_PORTS_MAX];
+	int node, count, i;
+
+	/* Set up the USB clocks correctly based on our oscillator frequency */
+	freq = clock_get_osc_freq();
+	config_clock(usb_pll[freq]);
+
+	/* count may return <0 on error */
+	count = fdtdec_find_aliases_for_id(blob, "usb",
+			COMPAT_NVIDIA_TEGRA20_USB, node_list, USB_PORTS_MAX);
+	for (i = 0; i < count; i++) {
+		debug("USB %d: ", i);
+		node = node_list[i];
+		if (!node)
+			continue;
+		if (fdt_decode_usb(blob, node, osc_freq, &config)) {
+			debug("Cannot decode USB node %s\n",
+			      fdt_get_name(blob, node, NULL));
+			return -1;
+		}
+
+		if (add_port(&config, usb_pll[freq]))
+			return -1;
+		set_host_mode(&config);
+	}
+	port_current = -1;
+
+	return 0;
+}