powerpc/t1023rdb: Add T1023 RDB board support

T1023RDB is a Freescale Reference Design Board that hosts the T1023 SoC.

T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
  - one 1G RGMII port on-board(RTL8211F PHY)
  - one 1G SGMII port on-board(RTL8211F PHY)
  - one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR:  128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging

As well updated T1024RDB to add T1023RDB.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix defconfig files]
Reviewed-by: York Sun <yorksun@freescale.com>

19 files changed, 382 insertions, 44 deletions

diff --git a/board/freescale/t102xrdb/MAINTAINERS b/board/freescale/t102xrdb/MAINTAINERS
index dc554d4d3a..297e63a6ee 100644
--- a/board/freescale/t102xrdb/MAINTAINERS
+++ b/board/freescale/t102xrdb/MAINTAINERS
@@ -8,3 +8,8 @@ F:	configs/T1024RDB_NAND_defconfig
 F:	configs/T1024RDB_SDCARD_defconfig
 F:	configs/T1024RDB_SPIFLASH_defconfig
 F:	configs/T1024RDB_SECURE_BOOT_defconfig
+F:	configs/T1023RDB_defconfig
+F:	configs/T1023RDB_NAND_defconfig
+F:	configs/T1023RDB_SDCARD_defconfig
+F:	configs/T1023RDB_SPIFLASH_defconfig
+F:	configs/T1023RDB_SECURE_BOOT_defconfig
diff --git a/board/freescale/t102xrdb/Makefile b/board/freescale/t102xrdb/Makefile
index a0cf8f6fbf..052006610e 100644
--- a/board/freescale/t102xrdb/Makefile
+++ b/board/freescale/t102xrdb/Makefile
@@ -8,7 +8,7 @@ ifdef CONFIG_SPL_BUILD
 obj-y += spl.o
 else
 obj-y   += t102xrdb.o
-obj-y   += cpld.o
+obj-$(CONFIG_T1024RDB)   += cpld.o
 obj-y   += eth_t102xrdb.o
 obj-$(CONFIG_PCI)       += pci.o
 endif
diff --git a/board/freescale/t102xrdb/README b/board/freescale/t102xrdb/README
index 2b17f50bae..922450e3c7 100644
--- a/board/freescale/t102xrdb/README
+++ b/board/freescale/t102xrdb/README
@@ -98,6 +98,30 @@ T1024RDB board Overview
      - Four I2C ports
 
 
+T1023RDB board Overview
+-----------------------
+- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
+- CoreNet fabric supporting coherent and noncoherent transactions with
+  prioritization and bandwidth allocation
+- SDRAM memory: 2GB Micron MT40A512M8HX unbuffered 32-bit DDR4 w/o ECC
+- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
+- Ethernet interfaces:
+  - one 1G RGMII port on-board(RTL8211FS PHY)
+  - one 1G SGMII port on-board(RTL8211FS PHY)
+  - one 2.5G SGMII port on-board(AQR105 PHY)
+- PCIe: Two Mini-PCIe connectors on-board.
+- SerDes: 4 lanes up to 10.3125GHz
+- NOR:  128MB S29GL01GS110TFIV10 Spansion NOR Flash
+- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
+- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
+- USB: one Type-A USB 2.0 port with internal PHY
+- eSDHC: support SD/MMC and eMMC card
+- 256Kbit M24256 I2C EEPROM
+- RTC: Real-time clock DS1339U on I2C bus
+- UART: one serial port on-board with RJ45 connector
+- Debugging: JTAG/COP for T1023 debugging
+
+
 Memory map on T1024RDB
 ----------------------
 Start Address  End Address      Description			Size
@@ -117,29 +141,39 @@ Start Address  End Address      Description			Size
 0x0_0000_0000  0x0_ffff_ffff    DDR				4GB
 
 
-128MB NOR Flash memory Map
---------------------------
+128MB NOR Flash Memory Layout
+-----------------------------
 Start Address   End Address     Definition			Max size
 0xEFF40000      0xEFFFFFFF      u-boot (current bank)		768KB
 0xEFF20000      0xEFF3FFFF      u-boot env (current bank)	128KB
 0xEFF00000      0xEFF1FFFF      FMAN Ucode (current bank)	128KB
 0xEFE00000      0xEFE3FFFF      QE firmware (current bank)	256KB
-0xED300000      0xEFEFFFFF      rootfs (alt bank)		44MB
+0xED300000      0xEFDFFFFF      rootfs (alt bank)		44MB
+0xED000000      0xED2FFFFF      Guest image #3 (alternate bank) 3MB
+0xECD00000      0xECFFFFFF      Guest image #2 (alternate bank) 3MB
+0xECA00000	0xECCFFFFF	Guest image #1 (alternate bank) 3MB
+0xEC900000	0xEC9FFFFF	HV config device tree(alt bank)	1MB
 0xEC800000      0xEC8FFFFF      Hardware device tree (alt bank) 1MB
-0xEC020000      0xEC7FFFFF      Linux.uImage (alt bank)		7MB + 875KB
+0xEC700000	0xEC7FFFFF	HV.uImage (alternate bank)	1MB
+0xEC020000      0xEC6FFFFF      Linux.uImage (alt bank)		~7MB
 0xEC000000      0xEC01FFFF      RCW (alt bank)			128KB
 0xEBF40000      0xEBFFFFFF      u-boot (alt bank)		768KB
 0xEBF20000      0xEBF3FFFF      u-boot env (alt bank)		128KB
 0xEBF00000      0xEBF1FFFF      FMAN ucode (alt bank)		128KB
 0xEBE00000      0xEBE3FFFF      QE firmware (alt bank)		256KB
-0xE9300000      0xEBEFFFFF      rootfs (current bank)		44MB
+0xE9300000      0xEBDFFFFF      rootfs (current bank)		44MB
+0xE9000000      0xE92FFFFF      Guest image #3 (current bank)   3MB
+0xE8D00000      0xE8FFFFFF      Guest image #2 (current bank)   3MB
+0xE8A00000	0xE8CFFFFF	Guest image #1 (current bank)	3MB
+0xE8900000	0xE89FFFFF	HV config device tree(cur bank) 1MB
 0xE8800000      0xE88FFFFF      Hardware device tree (cur bank) 1MB
-0xE8020000      0xE86FFFFF      Linux.uImage (current bank)	7MB + 875KB
+0xE8700000	0xE87FFFFF	HV.uImage (current bank)	1MB
+0xE8020000      0xE86FFFFF      Linux.uImage (current bank)	~7MB
 0xE8000000      0xE801FFFF      RCW (current bank)		128KB
 
 
-T1024 Clock frequency
----------------------
+T1024/T1023 Clock frequency
+---------------------------
 BIN   Core     DDR       Platform  FMan
 Bin1: 1400MHz  1600MT/s  400MHz    700MHz
 Bin2: 1200MHz  1600MT/s  400MHz    600MHz
@@ -155,16 +189,27 @@ Software configurations and board settings
    b. program u-boot.bin image to NOR flash
 	=> tftp 1000000 u-boot.bin
 	=> pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
-	set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
+	on T1024RDB:
+	   set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
+	on T1023RDB:
+	   set SW1[1:8] = '00010110', SW2[1] = '0', SW3[4] = '0' for NOR boot
 
    Switching between default bank0 and alternate bank4 on NOR flash
    To change boot source to vbank4:
-        via software:   run command 'cpld reset altbank' in u-boot.
-        via DIP-switch: set SW3[5:7] = '100'
+   on T1024RDB:
+	via software:   run command 'cpld reset altbank' in u-boot.
+	via DIP-switch: set SW3[5:7] = '100'
+   on T1023RDB:
+	via software:   run command 'gpio vbank4' in u-boot.
+	via DIP-switch: set SW3[5:7] = '100'
 
    To change boot source to vbank0:
-        via software:   run command 'cpld reset' in u-boot.
-        via DIP-Switch: set SW3[5:7] = '000'
+   on T1024RDB:
+	via software:   run command 'cpld reset' in u-boot.
+	via DIP-Switch: set SW3[5:7] = '000'
+   on T1023RDB:
+	via software:   run command 'gpio vbank0' in u-boot.
+	via DIP-switch: set SW3[5:7] = '000'
 
 2. NAND Boot:
    a. build PBL image for NAND boot
@@ -183,8 +228,11 @@ Software configurations and board settings
    b. program u-boot-with-spl-pbl.bin to SPI flash
 	=> tftp 1000000 u-boot-with-spl-pbl.bin
 	=> sf probe 0
-	=> sf erase 0 f0000
+	=> sf erase 0 100000
 	=> sf write 1000000 0 $filesize
+	=> tftp 1000000 fsl_fman_ucode_t1024_xx.bin
+	=> sf erase 100000 100000
+	=> sf write 1000000 110000 20000
 	set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
 
 4. SD Boot:
@@ -236,23 +284,34 @@ Start		End		Definition	Size
 0x200000	0x27FFFF	QE Firmware	512KB(1 block)
 
 
+NAND Flash memory Map on T1023RDB
+----------------------------------------------------
+Start		End		Definition	Size
+0x000000	0x0FFFFF	u-boot		1MB
+0x100000	0x15FFFF	u-boot env	8KB
+0x160000	0x17FFFF	FMAN Ucode	128KB
+
+
 SD Card memory Map on T1024RDB
 ----------------------------------------------------
 Block		#blocks		Definition	Size
 0x008		2048		u-boot img	1MB
 0x800		0016		u-boot env	8KB
 0x820		0256		FMAN Ucode	128KB
-0x920		0256		QE Firmware	128KB
+0x920		0256		QE Firmware	128KB(only T1024RDB)
 
 
-SPI Flash memory Map on T1024RDB
+64MB SPI Flash memory Map on T102xRDB
 ----------------------------------------------------
 Start		End		Definition	Size
 0x000000	0x0FFFFF	u-boot img	1MB
 0x100000	0x101FFF	u-boot env	8KB
 0x110000	0x12FFFF	FMAN Ucode	128KB
-0x130000	0x14FFFF	QE Firmware	128KB
+0x130000	0x14FFFF	QE Firmware	128KB(only T1024RDB)
+0x300000	0x3FFFFF	device tree	128KB
+0x400000	0x9FFFFF	Linux kernel    6MB
+0xa00000	0x3FFFFFF	rootfs		54MB
 
 
-For more details, please refer to T1024RDB Reference Manual and access
-website www.freescale.com and Freescale QorIQ SDK Infocenter document.
+For more details, please refer to T1024RDB Reference Manual
+and Freescale QorIQ SDK Infocenter document.
diff --git a/board/freescale/t102xrdb/ddr.c b/board/freescale/t102xrdb/ddr.c
index a2a8f4ccf0..adf9fd5f78 100644
--- a/board/freescale/t102xrdb/ddr.c
+++ b/board/freescale/t102xrdb/ddr.c
@@ -135,8 +135,83 @@ found:
 	/* for DDR bus 32bit test on T1024 */
 	popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
 #endif
+
+#ifdef CONFIG_T1023RDB
+	popts->wrlvl_ctl_2 = 0x07070606;
+	popts->half_strength_driver_enable = 1;
+#endif
 }
 
+#ifdef CONFIG_SYS_DDR_RAW_TIMING
+/* 2GB discrete DDR4 MT40A512M8HX on T1023RDB */
+dimm_params_t ddr_raw_timing = {
+	.n_ranks = 1,
+	.rank_density = 0x80000000,
+	.capacity = 0x80000000,
+	.primary_sdram_width = 32,
+	.ec_sdram_width = 8,
+	.registered_dimm = 0,
+	.mirrored_dimm = 0,
+	.n_row_addr = 15,
+	.n_col_addr = 10,
+	.bank_addr_bits = 2,
+	.bank_group_bits = 2,
+	.edc_config = 0,
+	.burst_lengths_bitmask = 0x0c,
+	.tckmin_x_ps = 938,
+	.tckmax_ps = 1500,
+	.caslat_x = 0x000DFA00,
+	.taa_ps = 13500,
+	.trcd_ps = 13500,
+	.trp_ps = 13500,
+	.tras_ps = 33000,
+	.trc_ps = 46500,
+	.trfc1_ps = 260000,
+	.trfc2_ps = 160000,
+	.trfc4_ps = 110000,
+	.tfaw_ps = 25000,
+	.trrds_ps = 3700,
+	.trrdl_ps = 5300,
+	.tccdl_ps = 5355,
+	.refresh_rate_ps = 7800000,
+	.dq_mapping[0] = 0x0,
+	.dq_mapping[1] = 0x0,
+	.dq_mapping[2] = 0x0,
+	.dq_mapping[3] = 0x0,
+	.dq_mapping[4] = 0x0,
+	.dq_mapping[5] = 0x0,
+	.dq_mapping[6] = 0x0,
+	.dq_mapping[7] = 0x0,
+	.dq_mapping[8] = 0x0,
+	.dq_mapping[9] = 0x0,
+	.dq_mapping[10] = 0x0,
+	.dq_mapping[11] = 0x0,
+	.dq_mapping[12] = 0x0,
+	.dq_mapping[13] = 0x0,
+	.dq_mapping[14] = 0x0,
+	.dq_mapping[15] = 0x0,
+	.dq_mapping[16] = 0x0,
+	.dq_mapping[17] = 0x0,
+	.dq_mapping_ors = 1,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+		unsigned int controller_number,
+		unsigned int dimm_number)
+{
+	const char dimm_model[] = "Fixed DDR4 on board";
+
+	if (((controller_number == 0) && (dimm_number == 0)) ||
+	    ((controller_number == 1) && (dimm_number == 0))) {
+		memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+		memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+		memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+	}
+
+	return 0;
+}
+#endif
+
 #if defined(CONFIG_DEEP_SLEEP)
 void board_mem_sleep_setup(void)
 {
@@ -155,8 +230,9 @@ phys_size_t initdram(int board_type)
 	phys_size_t dram_size;
 
 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
+#ifndef CONFIG_SYS_DDR_RAW_TIMING
 	puts("Initializing....using SPD\n");
-
+#endif
 	dram_size = fsl_ddr_sdram();
 	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
 	dram_size *= 0x100000;
diff --git a/board/freescale/t102xrdb/eth_t102xrdb.c b/board/freescale/t102xrdb/eth_t102xrdb.c
index f611ff07e9..dd386bc3a9 100644
--- a/board/freescale/t102xrdb/eth_t102xrdb.c
+++ b/board/freescale/t102xrdb/eth_t102xrdb.c
@@ -1,6 +1,8 @@
 /*
  * Copyright 2014 Freescale Semiconductor, Inc.
  *
+ * Shengzhou Liu <Shengzhou.Liu@freescale.com>
+ *
  * SPDX-License-Identifier:     GPL-2.0+
  */
 
@@ -56,6 +58,7 @@ int board_eth_init(bd_t *bis)
 	fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR);
 
 	switch (srds_s1) {
+#ifdef CONFIG_T1024RDB
 	case 0x95:
 		/* set the on-board RGMII2  PHY */
 		fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
@@ -63,10 +66,17 @@ int board_eth_init(bd_t *bis)
 		/* set 10G XFI with Aquantia AQR105 PHY */
 		fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
 		break;
+#endif
+	case 0x6a:
+	case 0x6b:
 	case 0x77:
 	case 0x135:
 		/* set the on-board 2.5G SGMII AQR105 PHY */
-		fm_info_set_phy_address(FM1_DTSEC3, SGMII_PHY1_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC3, SGMII_AQR_PHY_ADDR);
+#ifdef CONFIG_T1023RDB
+		/* set the on-board 1G SGMII RTL8211F PHY */
+		fm_info_set_phy_address(FM1_DTSEC1, SGMII_RTK_PHY_ADDR);
+#endif
 		break;
 	default:
 		printf("SerDes protocol 0x%x is not supported on T102xRDB\n",
@@ -81,6 +91,14 @@ int board_eth_init(bd_t *bis)
 			dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
 			fm_info_set_mdio(i, dev);
 			break;
+		case PHY_INTERFACE_MODE_SGMII:
+#if defined(CONFIG_T1023RDB)
+			dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+#elif defined(CONFIG_T1024RDB)
+			dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
+#endif
+			fm_info_set_mdio(i, dev);
+			break;
 		case PHY_INTERFACE_MODE_SGMII_2500:
 			dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
 			fm_info_set_mdio(i, dev);
@@ -110,13 +128,16 @@ int board_eth_init(bd_t *bis)
 void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
 			      enum fm_port port, int offset)
 {
-	if ((fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) &&
-	    (port == FM1_DTSEC3)) {
+#if defined(CONFIG_T1024RDB)
+	if (((fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) ||
+	     (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII)) &&
+			(port == FM1_DTSEC3)) {
 		fdt_set_phy_handle(fdt, compat, addr, "sg_2500_aqr105_phy4");
 		fdt_setprop(fdt, offset, "phy-connection-type",
 			    "sgmii-2500", 10);
 		fdt_status_disabled_by_alias(fdt, "xg_aqr105_phy3");
 	}
+#endif
 }
 
 void fdt_fixup_board_enet(void *fdt)
diff --git a/board/freescale/t102xrdb/t1023_rcw.cfg b/board/freescale/t102xrdb/t1023_rcw.cfg
new file mode 100644
index 0000000000..fa781d61a5
--- /dev/null
+++ b/board/freescale/t102xrdb/t1023_rcw.cfg
@@ -0,0 +1,8 @@
+#PBL preamble and RCW header for T1023RDB
+aa55aa55 010e0100
+#SerDes Protocol: 0x77
+#Core/DDR: 1400Mhz/1600MT/s with single source clock
+0810000e 00000000 00000000 00000000
+3b800003 00000012 e8104000 21000000
+00000000 00000000 00000000 00020800
+00000130 04020200 00000000 00000006
diff --git a/board/freescale/t102xrdb/t102xrdb.c b/board/freescale/t102xrdb/t102xrdb.c
index e196f12ac7..f971976d73 100644
--- a/board/freescale/t102xrdb/t102xrdb.c
+++ b/board/freescale/t102xrdb/t102xrdb.c
@@ -18,11 +18,25 @@
 #include <asm/fsl_liodn.h>
 #include <fm_eth.h>
 #include "t102xrdb.h"
+#ifdef CONFIG_T1024RDB
 #include "cpld.h"
+#endif
 #include "../common/sleep.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#ifdef CONFIG_T1023RDB
+enum {
+	GPIO1_SD_SEL    = 0x00020000, /* GPIO1_14, 0: EMMC, 1:SD/MMC */
+	GPIO1_EMMC_SEL,
+	GPIO1_VBANK0,
+	GPIO1_VBANK4    = 0x00008000, /* GPIO1_16/20/22,  100:vBank4 */
+	GPIO1_VBANK_MASK = 0x00008a00,
+	GPIO1_DIR_OUTPUT = 0x00028a00,
+	GPIO1_GET_VAL,
+};
+#endif
+
 int checkboard(void)
 {
 	struct cpu_type *cpu = gd->arch.cpu;
@@ -34,14 +48,17 @@ int checkboard(void)
 	srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
 
 	printf("Board: %sRDB, ", cpu->name);
-	printf("Board rev: 0x%02x CPLD ver: 0x%02x, boot from ",
+#ifdef CONFIG_T1024RDB
+	printf("Board rev: 0x%02x CPLD ver: 0x%02x, ",
 	       CPLD_READ(hw_ver), CPLD_READ(sw_ver));
+#endif
+	printf("boot from ");
 
 #ifdef CONFIG_SDCARD
 	puts("SD/MMC\n");
 #elif CONFIG_SPIFLASH
 	puts("SPI\n");
-#else
+#elif defined(CONFIG_T1024RDB)
 	u8 reg;
 
 	reg = CPLD_READ(flash_csr);
@@ -52,17 +69,25 @@ int checkboard(void)
 		reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
 		printf("NOR vBank%d\n", reg);
 	}
+#elif defined(CONFIG_T1023RDB)
+#ifdef CONFIG_NAND
+	puts("NAND\n");
+#else
+	printf("NOR vBank%d\n", (t1023rdb_gpio_ctrl(GPIO1_GET_VAL) &
+	       GPIO1_VBANK4) >> 15 ? 4 : 0);
+#endif
 #endif
 
 	puts("SERDES Reference Clocks:\n");
 	if (srds_s1 == 0x95)
 		printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]);
 	else
-		printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[0], freq[0]);
+		printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[0], freq[1]);
 
 	return 0;
 }
 
+#ifdef CONFIG_T1024RDB
 static void board_mux_lane(void)
 {
 	ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
@@ -82,6 +107,7 @@ static void board_mux_lane(void)
 	}
 	CPLD_WRITE(boot_override, CPLD_OVERRIDE_MUX_EN);
 }
+#endif
 
 int board_early_init_f(void)
 {
@@ -124,7 +150,9 @@ int board_early_init_r(void)
 #ifdef CONFIG_SYS_DPAA_QBMAN
 	setup_portals();
 #endif
+#ifdef CONFIG_T1024RDB
 	board_mux_lane();
+#endif
 
 	return 0;
 }
@@ -170,3 +198,62 @@ int ft_board_setup(void *blob, bd_t *bd)
 
 	return 0;
 }
+
+
+#ifdef CONFIG_T1023RDB
+static u32 t1023rdb_gpio_ctrl(u32 ctrl_type)
+{
+	ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
+	u32 gpioval;
+
+	setbits_be32(&pgpio->gpdir, GPIO1_DIR_OUTPUT);
+	gpioval = in_be32(&pgpio->gpdat);
+
+	switch (ctrl_type) {
+	case GPIO1_SD_SEL:
+		gpioval |= GPIO1_SD_SEL;
+		break;
+	case GPIO1_EMMC_SEL:
+		gpioval &= ~GPIO1_SD_SEL;
+		break;
+	case GPIO1_VBANK0:
+		gpioval &= ~GPIO1_VBANK_MASK;
+		break;
+	case GPIO1_VBANK4:
+		gpioval &= ~GPIO1_VBANK_MASK;
+		gpioval |= GPIO1_VBANK4;
+		break;
+	case GPIO1_GET_VAL:
+		return gpioval;
+	default:
+		break;
+	}
+	out_be32(&pgpio->gpdat, gpioval);
+
+	return 0;
+}
+
+static int gpio_cmd(cmd_tbl_t *cmdtp, int flag, int argc,
+		    char * const argv[])
+{
+	if (argc < 2)
+		return CMD_RET_USAGE;
+	if (!strcmp(argv[1], "vbank0"))
+		t1023rdb_gpio_ctrl(GPIO1_VBANK0);
+	else if (!strcmp(argv[1], "vbank4"))
+		t1023rdb_gpio_ctrl(GPIO1_VBANK4);
+	else if (!strcmp(argv[1], "sd"))
+		t1023rdb_gpio_ctrl(GPIO1_SD_SEL);
+	else if (!strcmp(argv[1], "EMMC"))
+		t1023rdb_gpio_ctrl(GPIO1_EMMC_SEL);
+	else
+		return CMD_RET_USAGE;
+	return 0;
+}
+
+U_BOOT_CMD(
+	gpio, 2, 0, gpio_cmd,
+	"for vbank0/vbank4/SD/eMMC switch control in runtime",
+	"command (e.g. gpio vbank4)"
+);
+#endif
diff --git a/board/freescale/t102xrdb/t102xrdb.h b/board/freescale/t102xrdb/t102xrdb.h
index 2f23579b8f..3f5d85aa82 100644
--- a/board/freescale/t102xrdb/t102xrdb.h
+++ b/board/freescale/t102xrdb/t102xrdb.h
@@ -9,5 +9,7 @@
 
 void fdt_fixup_board_enet(void *blob);
 void pci_of_setup(void *blob, bd_t *bd);
-
+#ifdef CONFIG_T1023RDB
+static u32 t1023rdb_gpio_ctrl(u32 ctrl_type);
+#endif
 #endif
diff --git a/configs/T1023RDB_NAND_defconfig b/configs/T1023RDB_NAND_defconfig
new file mode 100644
index 0000000000..c3ba6a198b
--- /dev/null
+++ b/configs/T1023RDB_NAND_defconfig
@@ -0,0 +1,5 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1023,T1023RDB,RAMBOOT_PBL,SPL_FSL_PBL,NAND"
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1023RDB_SDCARD_defconfig b/configs/T1023RDB_SDCARD_defconfig
new file mode 100644
index 0000000000..a2632aa2dc
--- /dev/null
+++ b/configs/T1023RDB_SDCARD_defconfig
@@ -0,0 +1,5 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1023,T1023RDB,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD"
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1023RDB_SECURE_BOOT_defconfig b/configs/T1023RDB_SECURE_BOOT_defconfig
new file mode 100644
index 0000000000..c2e2d7ecac
--- /dev/null
+++ b/configs/T1023RDB_SECURE_BOOT_defconfig
@@ -0,0 +1,4 @@
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1023,T1023RDB,SECURE_BOOT"
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1023RDB_SPIFLASH_defconfig b/configs/T1023RDB_SPIFLASH_defconfig
new file mode 100644
index 0000000000..202103cddb
--- /dev/null
+++ b/configs/T1023RDB_SPIFLASH_defconfig
@@ -0,0 +1,5 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1023,T1023RDB,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH"
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1023RDB_defconfig b/configs/T1023RDB_defconfig
new file mode 100644
index 0000000000..a839925fbc
--- /dev/null
+++ b/configs/T1023RDB_defconfig
@@ -0,0 +1,4 @@
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1023,T1023RDB"
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1024RDB_NAND_defconfig b/configs/T1024RDB_NAND_defconfig
index efbd5402d3..721419468f 100644
--- a/configs/T1024RDB_NAND_defconfig
+++ b/configs/T1024RDB_NAND_defconfig
@@ -1,5 +1,5 @@
 CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,RAMBOOT_PBL,SPL_FSL_PBL,NAND"
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,T1024RDB,RAMBOOT_PBL,SPL_FSL_PBL,NAND"
 CONFIG_PPC=y
 CONFIG_MPC85xx=y
 CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1024RDB_SDCARD_defconfig b/configs/T1024RDB_SDCARD_defconfig
index 65ae8d7cdd..9c3350593c 100644
--- a/configs/T1024RDB_SDCARD_defconfig
+++ b/configs/T1024RDB_SDCARD_defconfig
@@ -1,5 +1,5 @@
 CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD"
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,T1024RDB,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD"
 CONFIG_PPC=y
 CONFIG_MPC85xx=y
 CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1024RDB_SECURE_BOOT_defconfig b/configs/T1024RDB_SECURE_BOOT_defconfig
index 83772600a1..be014170d9 100644
--- a/configs/T1024RDB_SECURE_BOOT_defconfig
+++ b/configs/T1024RDB_SECURE_BOOT_defconfig
@@ -1,4 +1,4 @@
-CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,SECURE_BOOT"
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,T1024RDB,SECURE_BOOT"
 CONFIG_PPC=y
 CONFIG_MPC85xx=y
 CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1024RDB_SPIFLASH_defconfig b/configs/T1024RDB_SPIFLASH_defconfig
index 0b995730e6..5a59000bcf 100644
--- a/configs/T1024RDB_SPIFLASH_defconfig
+++ b/configs/T1024RDB_SPIFLASH_defconfig
@@ -1,5 +1,5 @@
 CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,T1024RDB,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH"
 CONFIG_PPC=y
 CONFIG_MPC85xx=y
 CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1024RDB_defconfig b/configs/T1024RDB_defconfig
index e19e404bd1..c22b3edbab 100644
--- a/configs/T1024RDB_defconfig
+++ b/configs/T1024RDB_defconfig
@@ -1,4 +1,4 @@
-CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024"
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,T1024RDB"
 CONFIG_PPC=y
 CONFIG_MPC85xx=y
 CONFIG_TARGET_T102XRDB=y
diff --git a/include/configs/T102xRDB.h b/include/configs/T102xRDB.h
index 84e8336a72..deff617ed4 100644
--- a/include/configs/T102xRDB.h
+++ b/include/configs/T102xRDB.h
@@ -11,6 +11,12 @@
 #ifndef __T1024RDB_H
 #define __T1024RDB_H
 
+#if defined(CONFIG_T1023RDB)
+#ifdef CONFIG_SPL
+#define CONFIG_SYS_NO_FLASH
+#endif
+#endif
+
 /* High Level Configuration Options */
 #define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_DISPLAY_BOARDINFO
@@ -35,7 +41,9 @@
 #define CONFIG_ENV_OVERWRITE
 
 /* support deep sleep */
+#ifdef CONFIG_PPC_T1024
 #define CONFIG_DEEP_SLEEP
+#endif
 #if defined(CONFIG_DEEP_SLEEP)
 #define CONFIG_SILENT_CONSOLE
 #define CONFIG_BOARD_EARLY_INIT_F
@@ -43,7 +51,11 @@
 
 #ifdef CONFIG_RAMBOOT_PBL
 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xrdb/t1024_pbi.cfg
+#if defined(CONFIG_T1024RDB)
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_rcw.cfg
+#elif defined(CONFIG_T1023RDB)
+#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_rcw.cfg
+#endif
 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
 #define CONFIG_SPL_ENV_SUPPORT
 #define CONFIG_SPL_SERIAL_SUPPORT
@@ -177,7 +189,11 @@
 #define CONFIG_ENV_SPI_MODE		0
 #define CONFIG_ENV_SIZE			0x2000		/* 8KB */
 #define CONFIG_ENV_OFFSET		0x100000	/* 1MB */
+#if defined(CONFIG_T1024RDB)
 #define CONFIG_ENV_SECT_SIZE		0x10000
+#elif defined(CONFIG_T1023RDB)
+#define CONFIG_ENV_SECT_SIZE		0x40000
+#endif
 #elif defined(CONFIG_SDCARD)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_ENV_IS_IN_MMC
@@ -188,7 +204,11 @@
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_SIZE			0x2000
+#if defined(CONFIG_T1024RDB)
 #define CONFIG_ENV_OFFSET		(2 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_T1023RDB)
+#define CONFIG_ENV_OFFSET		(10 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#endif
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 #define CONFIG_ENV_IS_IN_REMOTE
 #define CONFIG_ENV_ADDR		0xffe20000
@@ -209,7 +229,7 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 #define CONFIG_SYS_CLK_FREQ	100000000
-#define CONFIG_DDR_CLK_FREQ	66660000
+#define CONFIG_DDR_CLK_FREQ	100000000
 
 /*
  * These can be toggled for performance analysis, otherwise use default.
@@ -224,6 +244,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #endif
 
+#define CONFIG_CMD_MEMTEST
 #define CONFIG_SYS_MEMTEST_START	0x00200000 /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
 #define CONFIG_SYS_ALT_MEMTEST
@@ -265,13 +286,18 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_FSL_DDR_INTERACTIVE
+#if defined(CONFIG_T1024RDB)
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_FSL_DDR3
-
 #define CONFIG_SYS_SPD_BUS_NUM	0
 #define SPD_EEPROM_ADDRESS	0x51
-
 #define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */
+#elif defined(CONFIG_T1023RDB)
+#define CONFIG_SYS_FSL_DDR4
+#define CONFIG_SYS_DDR_RAW_TIMING
+#define CONFIG_SYS_SDRAM_SIZE   2048
+#endif
 
 /*
  * IFC Definitions
@@ -291,7 +317,12 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
 
 /* NOR Flash Timing Params */
+#if defined(CONFIG_T1024RDB)
 #define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
+#elif defined(CONFIG_T1023RDB)
+#define CONFIG_SYS_NOR_CSOR    (CSOR_NOR_ADM_SHIFT(4) | \
+				CSOR_NAND_TRHZ_80 | CSOR_NOR_ADM_SHFT_MODE_EN)
+#endif
 #define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
 				FTIM0_NOR_TEADC(0x5) | \
 				FTIM0_NOR_TEAHC(0x5))
@@ -315,6 +346,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}
 
+#ifdef CONFIG_T1024RDB
 /* CPLD on IFC */
 #define CONFIG_SYS_CPLD_BASE		0xffdf0000
 #define CONFIG_SYS_CPLD_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_CPLD_BASE)
@@ -336,6 +368,7 @@ unsigned long get_board_ddr_clk(void);
 						FTIM2_GPCM_TCH(0x8) | \
 						FTIM2_GPCM_TWP(0x1f))
 #define CONFIG_SYS_CS2_FTIM3		0x0
+#endif
 
 /* NAND Flash on IFC */
 #define CONFIG_NAND_FSL_IFC
@@ -352,6 +385,7 @@ unsigned long get_board_ddr_clk(void);
 				| CSPR_V)
 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
 
+#if defined(CONFIG_T1024RDB)
 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
 				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
@@ -359,9 +393,17 @@ unsigned long get_board_ddr_clk(void);
 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
 				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)
+#elif defined(CONFIG_T1023RDB)
+#define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_RAL_3	/* RAL 3Bytes */ \
+				| CSOR_NAND_RAL_3	/* RAL 3Bytes */ \
+				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
+				| CSOR_NAND_SPRZ_128	/* Spare size = 128 */ \
+				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+#endif
 
 #define CONFIG_SYS_NAND_ONFI_DETECTION
-
 /* ONFI NAND Flash mode0 Timing Params */
 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
 					FTIM0_NAND_TWP(0x18)   | \
@@ -381,8 +423,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_CMD_NAND
 
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)
-
 #if defined(CONFIG_NAND)
 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
@@ -536,7 +576,11 @@ unsigned long get_board_ddr_clk(void);
  */
 #define CONFIG_FSL_ESPI
 #define CONFIG_SPI_FLASH
+#if defined(CONFIG_T1024RDB)
 #define CONFIG_SPI_FLASH_STMICRO
+#elif defined(CONFIG_T1023RDB)
+#define CONFIG_SPI_FLASH_SPANSION
+#endif
 #define CONFIG_CMD_SF
 #define CONFIG_SPI_FLASH_BAR
 #define CONFIG_SF_DEFAULT_SPEED	10000000
@@ -736,8 +780,13 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_QE_FW_ADDR		(512 * 0x920)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#if defined(CONFIG_T1024RDB)
 #define CONFIG_SYS_FMAN_FW_ADDR		(3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #define CONFIG_SYS_QE_FW_ADDR		(4 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_T1023RDB)
+#define CONFIG_SYS_FMAN_FW_ADDR		(11 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_QE_FW_ADDR		(12 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#endif
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
@@ -762,10 +811,16 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_PHYLIB_10G
 #define CONFIG_PHY_REALTEK
 #define CONFIG_PHY_AQUANTIA
+#if defined(CONFIG_T1024RDB)
 #define RGMII_PHY1_ADDR		0x2
 #define RGMII_PHY2_ADDR		0x6
-#define SGMII_PHY1_ADDR		0x2
+#define SGMII_AQR_PHY_ADDR	0x2
 #define FM1_10GEC1_PHY_ADDR	0x1
+#elif defined(CONFIG_T1023RDB)
+#define RGMII_PHY1_ADDR		0x1
+#define SGMII_RTK_PHY_ADDR	0x3
+#define SGMII_AQR_PHY_ADDR	0x2
+#endif
 #endif
 
 #ifdef CONFIG_FMAN_ENET
@@ -855,21 +910,23 @@ unsigned long get_board_ddr_clk(void);
  */
 #define CONFIG_ROOTPATH		"/opt/nfsroot"
 #define CONFIG_BOOTFILE		"uImage"
-#define CONFIG_UBOOTPATH	"u-boot.bin" /* U-Boot image on TFTP server */
+#define CONFIG_UBOOTPATH	u-boot.bin /* U-Boot image on TFTP server */
 #define CONFIG_LOADADDR		1000000 /* default location for tftp, bootm */
 #define CONFIG_BOOTDELAY	10	/* -1 disables auto-boot */
 #define CONFIG_BAUDRATE		115200
 #define __USB_PHY_TYPE		utmi
 
 #ifdef CONFIG_PPC_T1024
-#define CONFIG_BOARDNAME "t1024rdb"
+#define CONFIG_BOARDNAME t1024rdb
+#define BANK_INTLV cs0_cs1
 #else
-#define CONFIG_BOARDNAME "t1023rdb"
+#define CONFIG_BOARDNAME t1023rdb
+#define BANK_INTLV  null
 #endif
 
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
 	"hwconfig=fsl_ddr:ctlr_intlv=cacheline,"		\
-	"bank_intlv=cs0_cs1\0"					\
+	"bank_intlv=" __stringify(BANK_INTLV) "\0"		\
 	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"  \
 	"ramdiskfile=" __stringify(CONFIG_BOARDNAME) "/ramdisk.uboot\0" \
 	"fdtfile=" __stringify(CONFIG_BOARDNAME) "/"		\