usb/ehci: Add USB support for the MX6Q

Currently, only USB Host 1 is supported.

Cc: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>

5 files changed, 223 insertions, 0 deletions

diff --git a/arch/arm/cpu/armv7/mx6/clock.c b/arch/arm/cpu/armv7/mx6/clock.c
index fa3a124807..ef98563ff7 100644
--- a/arch/arm/cpu/armv7/mx6/clock.c
+++ b/arch/arm/cpu/armv7/mx6/clock.c
@@ -36,6 +36,19 @@ enum pll_clocks {
 
 struct imx_ccm_reg *imx_ccm = (struct imx_ccm_reg *)CCM_BASE_ADDR;
 
+void enable_usboh3_clk(unsigned char enable)
+{
+	u32 reg;
+
+	reg = __raw_readl(&imx_ccm->CCGR6);
+	if (enable)
+		reg |= MXC_CCM_CCGR_CG_MASK << MXC_CCM_CCGR0_CG0_OFFSET;
+	else
+		reg &= ~(MXC_CCM_CCGR_CG_MASK << MXC_CCM_CCGR0_CG0_OFFSET);
+	__raw_writel(reg, &imx_ccm->CCGR6);
+
+}
+
 static u32 decode_pll(enum pll_clocks pll, u32 infreq)
 {
 	u32 div;
diff --git a/arch/arm/include/asm/arch-mx6/clock.h b/arch/arm/include/asm/arch-mx6/clock.h
index 636458f8a0..613809bdd6 100644
--- a/arch/arm/include/asm/arch-mx6/clock.h
+++ b/arch/arm/include/asm/arch-mx6/clock.h
@@ -46,5 +46,6 @@ enum mxc_clock {
 u32 imx_get_uartclk(void);
 u32 imx_get_fecclk(void);
 unsigned int mxc_get_clock(enum mxc_clock clk);
+void enable_usboh3_clk(unsigned char enable);
 
 #endif /* __ASM_ARCH_CLOCK_H */
diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h
index 6b7589b78a..6a200bb865 100644
--- a/arch/arm/include/asm/arch-mx6/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx6/imx-regs.h
@@ -111,6 +111,9 @@
 #define KPP_BASE_ADDR               (AIPS1_OFF_BASE_ADDR + 0x38000)
 #define WDOG1_BASE_ADDR             (AIPS1_OFF_BASE_ADDR + 0x3C000)
 #define WDOG2_BASE_ADDR             (AIPS1_OFF_BASE_ADDR + 0x40000)
+#define ANATOP_BASE_ADDR            (AIPS1_OFF_BASE_ADDR + 0x48000)
+#define USB_PHY0_BASE_ADDR          (AIPS1_OFF_BASE_ADDR + 0x49000)
+#define USB_PHY1_BASE_ADDR          (AIPS1_OFF_BASE_ADDR + 0x4a000)
 #define CCM_BASE_ADDR               (AIPS1_OFF_BASE_ADDR + 0x44000)
 #define ANATOP_BASE_ADDR            (AIPS1_OFF_BASE_ADDR + 0x48000)
 #define SNVS_BASE_ADDR              (AIPS1_OFF_BASE_ADDR + 0x4C000)
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 5fdc97b8c8..53ad70af23 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -44,6 +44,7 @@ endif
 COBJS-$(CONFIG_USB_EHCI_MXC) += ehci-mxc.o
 COBJS-$(CONFIG_USB_EHCI_MXS) += ehci-mxs.o
 COBJS-$(CONFIG_USB_EHCI_MX5) += ehci-mx5.o
+COBJS-$(CONFIG_USB_EHCI_MX6) += ehci-mx6.o
 COBJS-$(CONFIG_USB_EHCI_OMAP) += ehci-omap.o
 COBJS-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o
 COBJS-$(CONFIG_USB_EHCI_IXP4XX) += ehci-ixp.o
diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
new file mode 100644
index 0000000000..b7bf49d6a4
--- /dev/null
+++ b/drivers/usb/host/ehci-mx6.c
@@ -0,0 +1,205 @@
+/*
+ * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
+ * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ */
+
+#include <common.h>
+#include <usb.h>
+#include <errno.h>
+#include <linux/compiler.h>
+#include <usb/ehci-fsl.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/mx6x_pins.h>
+#include <asm/arch/iomux-v3.h>
+
+#include "ehci.h"
+#include "ehci-core.h"
+
+#define USB_OTGREGS_OFFSET	0x000
+#define USB_H1REGS_OFFSET	0x200
+#define USB_H2REGS_OFFSET	0x400
+#define USB_H3REGS_OFFSET	0x600
+#define USB_OTHERREGS_OFFSET	0x800
+
+#define USB_H1_CTRL_OFFSET	0x04
+
+#define USBPHY_CTRL				0x00000030
+#define USBPHY_CTRL_SET				0x00000034
+#define USBPHY_CTRL_CLR				0x00000038
+#define USBPHY_CTRL_TOG				0x0000003c
+
+#define USBPHY_PWD				0x00000000
+#define USBPHY_CTRL_SFTRST			0x80000000
+#define USBPHY_CTRL_CLKGATE			0x40000000
+#define USBPHY_CTRL_ENUTMILEVEL3		0x00008000
+#define USBPHY_CTRL_ENUTMILEVEL2		0x00004000
+
+#define ANADIG_USB2_CHRG_DETECT			0x00000210
+#define ANADIG_USB2_CHRG_DETECT_EN_B		0x00100000
+#define ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B	0x00080000
+
+#define ANADIG_USB2_PLL_480_CTRL		0x00000020
+#define ANADIG_USB2_PLL_480_CTRL_SET		0x00000024
+#define ANADIG_USB2_PLL_480_CTRL_CLR		0x00000028
+#define ANADIG_USB2_PLL_480_CTRL_BYPASS		0x00010000
+#define ANADIG_USB2_PLL_480_CTRL_ENABLE		0x00002000
+#define ANADIG_USB2_PLL_480_CTRL_POWER		0x00001000
+#define ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS	0x00000040
+
+
+#define UCTRL_OVER_CUR_POL	(1 << 8) /* OTG Polarity of Overcurrent */
+#define UCTRL_OVER_CUR_DIS	(1 << 7) /* Disable OTG Overcurrent Detection */
+
+/* USBCMD */
+#define UH1_USBCMD_OFFSET	0x140
+#define UCMD_RUN_STOP           (1 << 0) /* controller run/stop */
+#define UCMD_RESET		(1 << 1) /* controller reset */
+
+static void usbh1_internal_phy_clock_gate(int on)
+{
+	void __iomem *phy_reg = (void __iomem *)USB_PHY1_BASE_ADDR;
+
+	phy_reg += on ? USBPHY_CTRL_CLR : USBPHY_CTRL_SET;
+	__raw_writel(USBPHY_CTRL_CLKGATE, phy_reg);
+}
+
+static void usbh1_power_config(void)
+{
+	void __iomem *anatop_base = (void __iomem *)ANATOP_BASE_ADDR;
+
+	/*
+	 * Some phy and power's special controls for host1
+	 * 1. The external charger detector needs to be disabled
+	 * or the signal at DP will be poor
+	 * 2. The PLL's power and output to usb for host 1
+	 * is totally controlled by IC, so the Software only needs
+	 * to enable them at initializtion.
+	 */
+	__raw_writel(ANADIG_USB2_CHRG_DETECT_EN_B |
+		     ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B,
+		     anatop_base + ANADIG_USB2_CHRG_DETECT);
+
+	__raw_writel(ANADIG_USB2_PLL_480_CTRL_BYPASS,
+		     anatop_base + ANADIG_USB2_PLL_480_CTRL_CLR);
+
+	__raw_writel(ANADIG_USB2_PLL_480_CTRL_ENABLE |
+		     ANADIG_USB2_PLL_480_CTRL_POWER |
+		     ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS,
+		     anatop_base + ANADIG_USB2_PLL_480_CTRL_SET);
+}
+
+static int usbh1_phy_enable(void)
+{
+	void __iomem *phy_reg = (void __iomem *)USB_PHY1_BASE_ADDR;
+	void __iomem *phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
+	void __iomem *usb_cmd =	(void __iomem *)(USBOH3_USB_BASE_ADDR +
+						 USB_H1REGS_OFFSET +
+						 UH1_USBCMD_OFFSET);
+	u32 val;
+
+	/* Stop then Reset */
+	val = __raw_readl(usb_cmd);
+	val &= ~UCMD_RUN_STOP;
+	__raw_writel(val, usb_cmd);
+	while (__raw_readl(usb_cmd) & UCMD_RUN_STOP)
+		;
+
+	val = __raw_readl(usb_cmd);
+	val |= UCMD_RESET;
+	__raw_writel(val, usb_cmd);
+	while (__raw_readl(usb_cmd) & UCMD_RESET)
+		;
+
+	/* Reset USBPHY module */
+	val = __raw_readl(phy_ctrl);
+	val |= USBPHY_CTRL_SFTRST;
+	__raw_writel(val, phy_ctrl);
+	udelay(10);
+
+	/* Remove CLKGATE and SFTRST */
+	val = __raw_readl(phy_ctrl);
+	val &= ~(USBPHY_CTRL_CLKGATE | USBPHY_CTRL_SFTRST);
+	__raw_writel(val, phy_ctrl);
+	udelay(10);
+
+	/* Power up the PHY */
+	__raw_writel(0, phy_reg + USBPHY_PWD);
+	/* enable FS/LS device */
+	val = __raw_readl(phy_reg + USBPHY_CTRL);
+	val |= (USBPHY_CTRL_ENUTMILEVEL2 | USBPHY_CTRL_ENUTMILEVEL3);
+	__raw_writel(val, phy_reg + USBPHY_CTRL);
+
+	return 0;
+}
+
+static void usbh1_oc_config(void)
+{
+	void __iomem *usb_base = (void __iomem *)USBOH3_USB_BASE_ADDR;
+	void __iomem *usbother_base = usb_base + USB_OTHERREGS_OFFSET;
+	u32 val;
+
+	val = __raw_readl(usbother_base + USB_H1_CTRL_OFFSET);
+#if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2
+	/* mx6qarm2 seems to required a different setting*/
+	val &= ~UCTRL_OVER_CUR_POL;
+#else
+	val |= UCTRL_OVER_CUR_POL;
+#endif
+	__raw_writel(val, usbother_base + USB_H1_CTRL_OFFSET);
+
+	val = __raw_readl(usbother_base + USB_H1_CTRL_OFFSET);
+	val |= UCTRL_OVER_CUR_DIS;
+	__raw_writel(val, usbother_base + USB_H1_CTRL_OFFSET);
+}
+
+int ehci_hcd_init(void)
+{
+	struct usb_ehci *ehci;
+
+	enable_usboh3_clk(1);
+	mdelay(1);
+
+	/* Do board specific initialization */
+	board_ehci_hcd_init(CONFIG_MXC_USB_PORT);
+
+#if CONFIG_MXC_USB_PORT == 1
+	/* USB Host 1 */
+	usbh1_power_config();
+	usbh1_oc_config();
+	usbh1_internal_phy_clock_gate(1);
+	usbh1_phy_enable();
+#else
+#error "MXC USB port not yet supported"
+#endif
+
+	ehci = (struct usb_ehci *)(USBOH3_USB_BASE_ADDR +
+		(0x200 * CONFIG_MXC_USB_PORT));
+	hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
+	hcor = (struct ehci_hcor *)((uint32_t)hccr +
+			HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
+	setbits_le32(&ehci->usbmode, CM_HOST);
+
+	__raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
+	setbits_le32(&ehci->portsc, USB_EN);
+
+	mdelay(10);
+
+	return 0;
+}
+
+int ehci_hcd_stop(void)
+{
+	return 0;
+}